激光超声方法研究固-固界面波传播特性

对界面波的传播特性进行了理论及实验研究.首先探讨了界面波的求根问题，基于黎曼面分析，给出了求解界面波特征方程所有根的一般方法.理论上对三种常见的界面波——Stoneley波，Leaky Rayleigh及Leaky Interface波传播机理进行了分析，描述了三种界面波的波矢及位移势在两种介质中的状态.最后基于光弹效应原理, 利用全光学的激光超声手段对界面波进行了实验测量，实测结果与理论符合很好.     

Inverse problems in cancellous bone: estimation of the ultrasonic properties of fast and slow waves using Bayesian probability theory

Quantitative ultrasonic characterization of cancellous bone can be complicated by artifacts introduced by analyzing acquired data consisting of two propagating waves (a fast wave and a slow wave) as if only one wave were present. Recovering the ultrasonic properties of overlapping fast and slow waves could therefore lead to enhancement of bone quality assessment. The current study uses Bayesian probability theory to estimate phase velocity and normalized broadband ultrasonic attenuation (nBUA) parameters in a model of fast and slow wave propagation. Calculations are carried out using Markov chain Monte Carlo with simulated annealing to approximate the marginal posterior probability densities for parameters in the model. The technique is applied to simulated data, to data acquired on two phantoms capable of generating two waves in acquired signals, and to data acquired on a human femur condyle specimen. The models are in good agreement with both the simulated and experimental data, and the values of the estimated ultrasonic parameters fall within expected ranges.     

Numerical and experimental study on the wave attenuation in bone--FDTD simulation of ultrasound propagation in cancellous bone

In cancellous bone, longitudinal waves often separate into fast and slow waves depending on the alignment of bone trabeculae in the propagation path. This interesting phenomenon becomes an effective tool for the diagnosis of osteoporosis because wave propagation behavior depends on the bone structure. Since the fast wave mainly propagates in trabeculae, this wave is considered to reflect the structure of trabeculae. For a new diagnosis method using the information of this fast wave, therefore, it is necessary to understand the generation mechanism and propagation behavior precisely. In this study, the generation process of fast wave was examined by numerical simulations using elastic finite-difference time-domain (FDTD) method and experimental measurements. As simulation models, three-dimensional X-ray computer tomography (CT) data of actual bone samples were used. Simulation and experimental results showed that the attenuation of fast wave was always higher in the early state of propagation, and they gradually decreased as the wave propagated in bone. This phenomenon is supposed to come from the complicated propagating paths of fast waves in cancellous bone.     

Determining attenuation properties of interfering fast and slow ultrasonic waves in cancellous bone

Previous studies have shown that interference between fast waves and slow waves can lead to observed negative dispersion in cancellous bone. In this study, the effects of overlapping fast and slow waves on measurements of the apparent attenuation as a function of propagation distance are investigated along with methods of analysis used to determine the attenuation properties. Two methods are applied to simulated data that were generated based on experimentally acquired signals taken from a bovine specimen. The first method uses a time-domain approach that was dictated by constraints imposed by the partial overlap of fast and slow waves. The second method uses a frequency-domain log-spectral subtraction technique on the separated fast and slow waves. Applying the time-domain analysis to the broadband data yields apparent attenuation behavior that is larger in the early stages of propagation and decreases as the wave travels deeper. In contrast, performing frequency-domain analysis on the separated fast waves and slow waves results in attenuation coefficients that are independent of propagation distance. Results suggest that features arising from the analysis of overlapping two-mode data may represent an alternate explanation for the previously reported apparent dependence on propagation distance of the attenuation coefficient of cancellous bone.     

Guided waves in a plate with linearly varying thickness: experimental and numerical results

The aim of this work is to give experimental and numerical results on the behaviour of guided waves that propagate downslope in a free elastic plate with slowly linearly varying thickness. We show experimentally the propagation of adiabatic modes, which are guided waves that adapt to the varying thickness of the plate. As the thickness is decreasing, a given guided wave will reach its thickness cut-off. When this happens, we show that two phenomena occur: the reflection of this wave and its propagation backward in the plate, its conversion into a different guided wave which goes on propagating downslope in the plate. The numerical study is done with the software Ansys, based on the finite element method. The results obtained confirm the experimental ones.     

Lamb and torsional waves and their use in flaw detection in tubes

Five separate issues concerning Lamb wave propagation are discussed: (1) the actual motion of the particles in sheet material; (2) the mechanism of the initiation of Lamb waves in plates; (3) the effect of pulse propagation as opposed to continuous waves; (4) wave propagation on the inner and outer surfaces of tubes; and (5) the propagation of waves in tubes at large angles of incidence, beyond the Lamb wave regime.     

含左手材料对称三层平板空气波导的模式特性

研究了左手材料作为衬底及覆盖层的对称三层平板空气波导的传输特性.快波和慢波都可以在这种波导中传播.快波不存在基模模式,只有0阶和1阶的TE或TM模才会出现慢波.当左手材料的相对介电常量和相对磁导率相等时,TE、TM模式完全简并,当其相异时简并消除.可以存在同阶模式的双传播模.     

A waveguide finite element aided analysis of the wave field on a stationary tyre, not in contact with the ground

Although tyre/road noise has been a research subject for more than three decades, there is still no consensus in the literature as to which waves on a tyre are mainly responsible for the radiation of sound during rolling. Even the free vibrational behaviour of a stationary (non-rotating) tyre, not in contact with the ground, is still not well understood in the mid- and high-frequency ranges. Thus, gaining an improved understanding of this behaviour is a natural first step towards illuminating the question of which waves on a rolling tyre contribute to sound radiation. This is the topic of the present paper, in which a model based on the waveguide finite element method (WFEM) is used to study free wave propagation, on a stationary tyre, in the range 0-1500 Hz. In the low-frequency region (0-300 Hz), wave propagation is found to be rather straightforward, with two main wave-types present. Both have cross-section modes involving a nearly rigid motion of the belt. For higher frequencies (300-1500 Hz) the behaviour is more complex, including phenomena such as ‘curve veering’ and waves for which the phase speed and group speed have opposite signs. Wave-types identified in this region include (i) waves involving mainly sidewall deformation, (ii) belt bending waves, (iii) a wave with significant extensional deformation of the central belt region and (iv) a wave with a ‘breathing’ cross-section mode. The phase speed corresponding to found waves is computed and their radiation efficiency is discussed, assuming free-field conditions. In a future publication, the tyre model will be used in conjunction with a contact model and a radiation model to investigate the contribution of these waves to radiated sound during rolling.     

Current discontinuities on superconducting cosmic strings

The propagation of current perturbations on superconducting cosmic strings is considered. The conditions for the existence of discontinuities similar to shock waves have been found. The formulas relating the string parameters and the discontinuity propagation speed are derived. The current growth law in a shock wave is deduced. The propagation speeds of shock waves with arbitrary amplitudes are calculated. The reason why there are no shock waves in the case of time-like currents (in the “electric” regime) is explained; this is attributable to the shock wave instability with respect to perturbations of the string world sheet.     

无碰撞等离子体电流片中的低频波

采用两种无碰撞二维三分量不可压缩磁流体力学（MHD）模型，计入电子扰动压力张量效应，研究了电流片等离子体的色散性质和波.由于得到的一般色散关系较为复杂，只解析讨论了电流片的中心区和电子β*e=0两种特殊情况.主要结果如下：(1)在短波区（kdi＞1），存在快磁声 动理学Alfven波和斜Alfven 哨声模，电子磁流体力学模型是足够精确的MHD模型；在长波区（kdi＜1＝，存在Alfven波和离子声波，理想的MHD模型是适用的.（2）电子β*e＝0情况下的结果，显然遗漏了一些波模（如离子声波和快磁声动理 关键词： 电流片 磁流体力学 电子压力张量 色散关系     

Ultrasonic waves propagation in absorbing thin plates application to paper characterization

Guided wave theory is applied to a thin orthotropic and absorbing plate for low frequency propagation of ultrasonic waves. The aim of this paper is to give some physical interpretations of the non-destructive characterization of paper materials, which are cellulosic fibrous networks. It is shown that the propagation problem reduces to two normal modes of propagation in the plane of the plate. Each of them depends on four complex and independent stiffnesses that are combinations of elementary complex stiffnesses of the media. The imaginary part of these stiffnesses corresponds to a possible mechanism of energy dissipation during the wave propagation for this kind of material. The reverse problem, which gives four complex values, is then numerically solved using a small attenuation assumption. The specially designed experimental set-up has led to the first measurements of tracing paper damping factors. The phase velocity measurements of the plate waves agree with the results already found by several paper researchers. As a particular and new result, the shear wave velocities are found to present a quasi-isotropic repartition in the plane of the paper sheet. It was found that the absorbing phenomenon can occur for each propagation mode in such a material. The attenuation values are small, except for one of them that corresponds to a coupling term in the propagation model. The anisotropy of their repartition is also shown in the case of quasi-longitudinal waves.     

Existence of extraordinary zero-curvature slowness curve in anisotropic elastic media

Acoustic wave propagation in elastic media is characterized by the slowness surface. The slowness surface consists of three sheets associated with three modes of wave propagation and the two outer sheets can have zero-curvature locally. It is shown that the outmost sheet can admit extraordinary zero-curvature and the slowness curve can appear as a straight line locally. Using the perturbation method, the conditions for the extraordinary zero-curvature are derived analytically without violating the thermodynamic condition for elastic media. The results can be applied to crystals with higher symmetry and to the study of phonon focusing and surface waves.     

In vitro estimation of fast and slow wave parameters of thin trabecular bone using space-alternating generalized expectation-maximization algorithm

In testing cancellous bone using ultrasound, two types of longitudinal Biot’s waves are observed in the received signal. These are known as fast and slow waves and their appearance depend on the alignment of bone trabeculae in the propagation path and the thickness of the specimen under test (SUT). They can be used as an effective tool for the diagnosis of osteoporosis because wave propagation behavior depends on the bone structure. However, the identification of these waves in the received signal can be difficult to achieve.In this study, ultrasonic wave propagation in a 4 mm thick bovine cancellous bone in the direction parallel to the trabecular alignment is considered. The observed Biot’s fast and slow longitudinal waves are superimposed; which makes it difficult to extract any information from the received signal. These two waves can be separated using the space alternating generalized expectation maximization (SAGE) algorithm. The latter has been used mainly in speech processing.In this new approach, parameters such as, arrival time, center frequency, bandwidth, amplitude, phase and velocity of each wave are estimated. The B-Scan images and its associated A-scans obtained through simulations using Biot’s finite-difference time-domain (FDTD) method are validated experimentally using a thin bone sample obtained from the femoral-head of a 30 months old bovine.     

Theory of sound propagation in superfluid-filled porous media

The theory of sound propagation in macroscopically isotropic and homogeneous porous media saturated with superfluid ⁴He has been developed neglecting all damping processes. The case when the normal fluid component is locked inside a porous medium by viscous forces is investigated in detail. It is shown that in this case one shear wave and two longitudinal, fast and slow, waves exist. Fast wave as well as slow wave is accompanied with temperature oscillations. The velocities of these waves are obtained.     

电磁偏置各向异性石墨烯界面的传播矩阵

基于电磁场边界条件和相位匹配,推导出电、磁偏置下呈各向异性的石墨烯导电界面的传播矩阵,并进一步给出各向异性石墨烯界面的反透射系数解析解;该传播矩阵耦合了基本的横电波和横磁波极化,并包括偏置电、磁场的影响.将跨石墨烯界面传播矩阵嵌入各向同性分层介质传播矩阵,获得的新传播矩阵可用于解析分析平面电磁波以任意角度入射含各向异性...     

Ultrasonic wave propagation in human cancellous bone: application of Biot theory

Ultrasonic wave propagation in human cancellous bone is considered. Reflection and transmission coefficients are derived for a slab of cancellous bone having an elastic frame using Biot's theory modified by the model of Johnson et al. [J. Fluid Mech. 176, 379-402 (1987)] for viscous exchange between fluid and structure. Numerical simulations of transmitted waves in the time domain are worked out by varying the modified Biot parameters. The variation is applied to the governing parameters and is about 20%. From this study, we can gain an insight into the sensitivity of each physical parameter used in this theory. Some parameters play an important role in slow-wave wave form, such as the viscous characteristic length lambda and pore fluid bulk modulus Kf. However, other parameters play an important role in the fast-wave wave form, such as solid density rhos and shear modulus N. We also note from these simulations that some parameters such as porosity phi, tortuosity alpha(infinty), thickness, solid bulk modulus Ks, and skeletal compressibility frame Kb, play an important role simultaneously in both fast and slow wave forms compared to other parameters which act on the wave form of just one of the two waves. The sensitivity of the modified Biot parameters with respect to the transmitted wave depends strongly on the coupling between the solid and fluid phases of the cancellous bone. Experimental results for slow and fast waves transmitted through human cancellous bone samples are given and compared with theoretical predictions.     

Phase and group velocities of fast and slow compressional waves in trabecular bone

This Letter is an extension to a multilayer model of porous bone first proposed by Hughes et al. [Ultrasound Med. Biol. 25, 811-821 (1999)]. Both slow and fast compressional waves propagate when the acoustic wave propagation is parallel to the trabecular alignment. However, a slow wave disappears at high refraction angles. To explain this phenomenon, the multilayer model is extended to compute group velocity surface and arrival times with an angle. Two major effects are highlighted as the refraction angle increases. First, the energy of the slow wave is refracted from the phase propagation direction. Second, the signals of fast and slow waves overlap. As a consequence, the slow wave may not be observed for a refraction angle greater than 40 degrees, which is in agreement with previous experimental data published by Hughes et al. and others.     

基于群速度失配的超声兰姆波二次谐波的时域测量方法

考虑到发射和接收换能器对超声兰姆波时域二次谐波信号所带来的不可避免的影响,提出一种基于基频与二倍频兰姆波群速度失配的超声兰姆波二次谐波的时域测量方法。当基频与二倍频超声兰姆波的相速度匹配而群速度失配时,在超声兰姆波传播过程中所发生的二次谐波信号,在时域上可与源于斜劈换能器的二次谐波信号相分离。采用仅源自于基频兰姆波的时域二次谐波的积分振幅,定量描述兰姆波二次谐波的发生效率。以铝板中传播的兰姆波为例,给出了时域二次谐波的具体测量过程。本文提出的测量方法放宽了超声兰姆波二次谐波的测量条件,且扣除了换能器对二次谐波信号所带来的影响,所测得的二次谐波信号完全来自于基频兰姆波时域信号的二次谐波发生效应。      

The identification of sound generating mechanisms of tyres

Tyre noise is generated by several mechanisms. With a modern tyre, wall vibration, air pumping and air resonant radiation are all considered to be important. But tyre noise generating mechanisms are still not clear due to the complication of tyre vibration behaviour. Vibrations of the tyre shell are the combination of several different wave types which appear at different frequencies. In a low frequency range, where the tyre behaves like an elastically supported beam, the circular ring model is used to analyze the dispersion relations. Above 300 Hz, which is the transition point from one-dimensional to two-dimensional waveguide properties of the passenger car tyre, a cylindrical shell model is used to analyze flexural waves propagation. Two important features on the wave propagation, wave-guide behaviour and the curvature effect of the tyre wall are analyzed. In consideration of noise radiation from tyre waves, most of the tyre waves observed in this study are inefficient sound radiators since their wavenumbers are larger than the acoustic wave number. As a result, It is observed that one of the most important features in sound radiation of a tyre shell is acoustically excited wave motion of the tyre wall.     

含少量气泡流体饱和孔隙介质中的弹性波

考虑孔隙流体中含有少量气泡,且气泡在声波作用下线性振动,研究声波在这种孔隙介质中的传播特性.本文先由流体质量守恒方程和孔隙度微分与流体压力微分的关系推导出了含有气泡形式的渗流连续性方程;在处理渗流连续性方程中的气体体积分数时间导数时,应用Commander气泡线性振动理论导出气体体积分数时间导数与流体压强时间导数的关系,进而得到了修正的Biot形式的渗流连续性方程;最后结合Biot动力学方程求得了含气泡形式的位移场方程,便可得到两类纵波及一类横波的声学特性.通过对快、慢纵波的频散、衰减及两类波引起的流体位移与固体位移关系的考察,发现少量气泡的存在对快纵波和慢纵波的传播特性影响较大.