Glucose biosensor based on gold nanoparticle-catalyzed luminol electrochemiluminescence on a three-dimensional sol–gel network

An electrochemiluminescent glucose biosensor was proposed based on gold nanoparticle-catalyzed luminol electrochemiluminescence (ECL). Gold nanoparticles were self-assembled onto silica sol–gel network, and then glucose oxidase was adsorbed on the surface of gold nanoparticles. The surface assembly process and the electrochemistry and ECL behaviors of the biosensor were investigated. The assembled gold nanoparticles could efficiently electrocatalyze luminol ECL. ECL intensity of the biosensor depended on scan rate, luminol concentration, and size of gold nanoparticles. The response of the ECL biosensor was linear over the range 1 μM to 5 mM with a detection limit of 0.2 μM glucose and showed satisfying reproducibility, stability and selectivity.     

Polyelectrolyte-mediated non-micellar synthesis of monodispersed ‘aggregates’ of gold nanoparticles using a microwave approach

‘Aggregates’ of monodispersed gold nanoparticles were synthesized for the first time in large quantities. Those particles were made in presence or in absence of gold seed in a polyelectrolyte solution using microwave heating for about 30–60 s. The average diameters of the particles calculated from TEM and SEM analysis were 22 ± 2 nm. Our analysis found that the polyelectrolyte acted as a reducing as well as a stabilizing agent. It controlled the growth of particles by aligning them on the polymeric chain and the nanoparticles were subsequently self-assembled to form an ‘aggregate’ structure. The synthetic procedure is very fast and the particles are stable for at least 6 months under ambient conditions.     

Synthesis and electrophoretic deposition of high-dielectric-constant SrTiO3 nanoparticles

We have investigated on the synthesis of SrTiO₃ nanoparticles whose bulk exhibits dielectric constant of 300, and their colloidal dispersion. As a result, we successfully synthesized SrTiO₃ nanoparticles with an average diameter of 134–485 nm measured by a scanning electron microscopic observation. The SrTiO₃ nanoparticles with a negative charge (ζ = −25 to −31 mV) can be dispersed as colloidal nanoparticles in water, and the average diameter in the dispersion were 138–356 nm measured by a dynamic light scattering technique. The colloidal dispersion of SrTiO₃ nanoparticles is promising for fabrication of low-voltage organic field-effect transistors (FETs) by a wet-processing fabrication. We have also successfully prepared SrTiO₃ films with a thickness of 1–10 μm on n-doped silicon substrates by an electrophoretic deposition technique. The SrTiO₃ films on the silicon substrates are likely used as dielectric gate insulator to low-voltage organic FETs after a sintering treatment.     

A new organic compound for the synthesis of gold nanoparticles

2,3,5,6-Tetrakis-(morpholinomethyl)hydroquinone (1) is used for the first time in the preparation of gold nanoparticles by the reduction of HAuCl₄ in water–methanol medium without using any capping agent. Compound 1 was prepared by Mannich-type aminomethylation of hydroquinone with morpholine. It is characterized by elemental analysis, FT-IR, UV–Vis and mass spectra and finally by single crystal X-ray diffraction. The ratio of HAuCl₄ and compound 1 played a vital role in controlling the shape and size of gold nanoparticles. The samples were characterized by Transmission Electron Microscopy (TEM), XRD, FT-IR, UV–Vis measurements. With the increasing amount of gold(III) solution with respect to compound 1, two different morphologies such as self-assembled and spherical gold nanoparticles have been observed. The results indicate that the morphology of gold nanoparticles with different sizes can be controlled by changing the concentrations of compound 1 and gold(III) solution.     

Influence of biomass and gold salt concentration on nanoparticle synthesis by the tropical marine yeast Yarrowia lipolytica NCIM 3589

Cell-associated gold nanoparticles and nanoplates were produced when varying number of Yarrowia lipolytica cells were incubated with different concentrations of chloroauric acid (HAuCl₄) at pH 4.5. With 10⁹ cells ml⁻¹ and 0.5 or 1.0 mM of the gold salt, the reaction mixtures developed a purple or golden red colour, respectively, and gold nanoparticles were synthesized. Nanoparticles of varying sizes were produced when 10¹⁰ cells ml⁻¹ were incubated with 0.5, 1.0 or 2.0 mM chloroauric acid salt. With 3.0, 4.0 or 5.0 mM HAuCl₄, nanoplates were also observed. With 10¹¹ cells ml⁻¹ nanoparticles were synthesized with almost all the gold salt concentrations. The cell-associated particles were released outside when nanoparticle-loaded cells were incubated at low temperature (20 °C) for 48 h. With increasing salt concentrations and a fixed number of cells, the size of the nanoparticles progressively increased. On the other hand, with increasing cell numbers and a constant gold salt concentration, the size of nanoparticles decreased. These results indicate that by varying the number of cells and the gold salt concentration, a variety of nanoparticles and nanoplates can be synthesized. Fourier transform infrared (FTIR) spectroscopy revealed the possible involvement of carboxyl, hydroxyl and amide groups on the cell surfaces in nanoparticle synthesis.     

Chitosan–iron oxide nanobiocomposite based immunosensor for ochratoxin-A

The rabbit immunoglobulin antibodies (IgGs) have been immobilized onto nanobiocomposite film of chitosan (CH)–iron oxide (Fe₃O₄₎ nanoparticles prepared onto indium–tin oxide (ITO) electrode for detection of ochratoxin-A (OTA). Excellent film forming ability and availability of –NH₂ group in CH and affinity of surface charged Fe₃O₄ nanoparticles for oxygen support the immobilization of IgGs. Differential pulse voltammettry (DPV) studies indicate that Fe₃O₄ nanoparticles provide increased electroactive surface area for loading of IgGs and improved electron transport between IgGs and electrode. IgGs/CH–Fe₃O₄ nanobiocomposite/ITO immunoelectrode exhibits improved characteristics such as low detection limit (0.5 ng dL⁻¹), fast response time (18 s) and high sensitivity (36 μA/ng dL⁻¹ cm⁻²) with respect to IgGs/CH/ITO immunoelectrode.     

Construction of simple gold nanoparticle aggregates with controlled plasmon–plasmon interactions

We have developed a colloidal assembly for the study of plasmon–plasmon interactions between gold nanoparticles. Colloidal aggregates of controlled size and interparticle spacing were synthesized on silica nanoparticle substrates. Following the immobilization of isolated gold nanoparticles onto silica nanoparticles, the surfaces of the adsorbed gold nanoparticles were functionalized with 4-aminobenzenethiol. This molecular linker attached additional gold nanoparticles to the ‘parent' gold nanoparticle, forming small nanoparticle aggregates. The optical absorption spectrum of these clusters differed from that of gold colloid in a manner consistent with plasmon–plasmon interactions between the gold nanoparticles.     

Role of electrolytes in the preparation of nanoparticles via the emulsion polymerization of vinyl pivalate

By controlling both the kind of ion and the ionic strength of electrolytes in an emulsion polymerization system of vinyl pivalate containing about 1% sodium lauryl sulfate as a surfactant, nanoparticles of polyvinylpivalate having a diameter of about 25 nm were successfully prepared. The use of high concentrations of lithium chloride and lithium sulfate (1.0 mol L⁻¹) prevented the nanoparticles from aggregating and produced nanoparticles sizes of 25–50 nm. Ammonium acetate and sodium acetate, on the other hand, accelerated the aggregate of the nanoparticles. These phenomena were examined in detail and found to be similar to the Hofmeister phenomena and the combination rule proposed by Craig et al.     

Structural and optical characterization of colloidal Se nanoparticles prepared via the acidic decomposition of sodium selenosulfate

Colloidal selenium nanoparticles (NPs) were synthesized via acidic decomposition of sodium selenosulfate. The effects of synthesis and post-synthesis treatment conditions on the size, structure and size distribution of the Se nanoparticles are discussed. It is shown that the decomposition of sodium selenosulfate with non-oxidative acids (e.g., HCl) in aqueous solutions of polymers (sodium polyphosphate, gelatin, polyvinyl alcohol, polyethyleneglycole) and surfactants (sodium dodecylsulfonate, cetylpyridinium chloride) results in the formation of amorphous 25–200 nm Se nanoparticles converting upon ageing at 90 °C into trigonal 150–250 nm Se nanocrystals. Optical properties (absorption and Raman spectra) of freshly prepared and aged Se nanoparticles both in colloidal solutions and in polymeric (polyvinyl alcohol) films are analyzed.     

Synthesis of MPTS-modified cobalt ferrite nanoparticles and their adsorption properties in relation to Au(III)

Cobalt ferrite magnetic nanoparticles (Co-MNP) were prepared by a co-precipitation method and subsequently coated with (3-mercaptopropyl)trimethoxysilane (MPTS) for the extraction and recovery of Au(III) from aqueous chloride solutions. Physical characterization of the MPTS-modified particles (Co-MPTS) was performed using FT-IR, TGA, and SEM. Results from FT-IR confirmed that MPTS was present on the surface of the magnetic nanoparticles. The amount of MPTS was 0.36 mmol g⁻¹ of Co-MPTS, obtained by elemental analysis. SEM images revealed aggregates composed of nanocrystalline Co-MPTS particles. The extraction efficiency as a function of the pH, contact time, and initial Au(III) concentration was evaluated. The modified particles showed maximum adsorption in the pH range from 1.0 to 4.0. The adsorption behavior of Co-MPTS toward Au(III) followed a Langmuir isotherm and the maximum adsorption capacity was found to be 120.5 mg g⁻¹. The stability of the modified materials was improved as compared to that of bare Co-MNP. The subsequent desorption of gold could be achieved by using acidified thiourea solution; the highest gold recovery reached 85%.     

Synthesis and characterization of the water-soluble silica-coated ZnS:Mn nanoparticles as fluorescent sensor for Cu ions

Silica-coated ZnS:Mn nanoparticles were synthesized by coating hydrophobic ZnS:Mn nanoparticles with silica shell through microemulsion. The core–shell structural nanoparticles were confirmed by X-ray diffraction (XRD) patterns, high-resolution transmission electron microscope (HRTEM) images and energy dispersive spectroscopy (EDS) measurements. Results show that each core–shell nanoparticle contains single ZnS:Mn nanoparticle within monodisperse silica nanospheres (40 nm). Photoluminescence (PL) spectroscopy and UV–vis spectrum were used to investigate the optical properties of the nanoparticles. Compared to uncoated ZnS:Mn nanoparticles, the silica-coated ZnS:Mn nanoparticles have the improved PL intensity as well as good photostability. The obtained silica-coated ZnS:Mn nanoparticles are water-soluble and have fluorescence sensitivity to Cu²⁺ ions. Quenching of fluorescence intensity of the silica-coated nanoparticles allows the detection of Cu²⁺ concentrations as low as 7.3 × 10⁻⁹ mol L⁻¹, thus affording a very sensitive detection system for this chemical species. The possible quenching mechanism is discussed.     

Synthesis and Stabilization of Gold Nanoparticles in Reverse Micelles of Aerosol OT and Triton X-100

Mechanisms of the formation and stabilization of gold nanoparticles in reverse micelles of micro-emulsions based on Triton X-100 (TX-100) and Aerosol OT (AOT) are studied. The instability of AOT-based microemulsions is shown to be caused by the oxidative degradation of gold nanoparticles in micelle water pools. Methods are proposed for the stabilization of these microemulsions. It is revealed that the mean size of gold nanoparticles synthesized in TX-100 reverse micelles in the presence of sodium sulfite is markedly smaller than that of particles prepared in AOT reverse micelles. This is explained by the fact that gold clusters are formed in the micelle shell rather than in the water pool. In the shell, the clusters are stabilized by oxyethylene groups of TX-100 molecules.__________Translated from Kolloidnyi Zhurnal, Vol. 67, No. 4, 2005, pp. 534–540.Original Russian Text Copyright © 2005 by Spirin, Brichkin, Razumov.     

Electrochemical determination of chromium(VI) using metallic nanoparticle-modified carbon screen-printed electrodes

Carbon screen-printed electrodes (CSPEs) modified with metal nanoparticles present an interesting alternative in the determination of chromium(VI) by differential pulse voltammetry (DPV).Metallic silver and gold nanoparticle deposits have been obtained by electrochemical deposition. Scanning electron microscopy measurements show that the electrochemically synthesized silver and gold nanoparticles are deposited in aggregated form.The detection limit for the analytical procedures developed in this work were 8.5 × 10⁻⁷ and 4.0 × 10⁻⁷ M for silver and gold nanoparticle-modifed CSPE, respectively.In terms of reproducibility, the precision of the above-mentioned method was calculated at 6.7% in %R.S.D. values for silver and 3.21% for gold nanoparticle CSPE.     

Glass–ceramic Li2S–P2S5 electrolytes prepared by a single step ball billing process and their application for all-solid-state lithium–ion batteries

We report that glass–ceramic Li₂S–P₂S₅ electrolytes can be prepared by a single step ball milling (SSBM) process. Mechanical ball milling of the xLi₂S·(100 − x)P₂S₅ system at 55 °C produced crystalline glass–ceramic materials exhibiting high Li-ion conductivity over 10⁻³ S cm⁻¹ at room temperature with a wide electrochemical stability window of 5 V. Silicon nanoparticles were evaluated as anode material in a solid-state Li battery employing the glass–ceramic electrolyte produced by the SSBM process and showed outstanding cycling stability.     

Synthesis of alginate stabilized gold nanoparticles by γ-irradiation with controllable size using different Au3+ concentration and seed particles enlargement

Gold nanoparticles with pre-selected size in the range 5–40 nm were synthesized by γ-irradiation of Au³⁺ solution containing natural polysaccharide alginate as a stabilizer. The gold nanoparticles with controllable size were prepared by two approaches: (i) varying the concentration of Au³⁺ from 0.25 to 1 mM and alginate from 0.25% to 1% (w/v) and (ii) enlargement of seed particles with double size from 20 to 40 nm at [Au³⁺]/[Au⁰]=6. The obtained gold nanoparticles were characterized by UV–vis spectroscopy and transmission electron microscopy. The results indicated that γ-irradiation method is suitable for production of gold nanoparticles with controllable size and high purity.     

Large-scale self-assembly of hydrophilic gold nanoparticles at oil/water interface and their electro-oxidation for nitric oxide in solution

Mono-/bi-layer Au nanoparticle films with large areas were prepared by the assembly of Au nanoparticles in aqueous colloid at toluene/water interfaces, which can be transferred onto the hydrophilic solid surface and adhere strongly to the substrate without any binding agent. The transferred Au nanoparticle films exhibited satisfactory catalytic performance for electro-oxidizing nitric oxide (NO) in solution, and had a low detection limit (2.7 × 10⁻⁸ mol/L), a rapid response time (less than 0.5 s) and a wide linear range (5.0 × 10⁻⁸–1.0 × 10⁻⁵ mol/L) for the detection of NO in solution. UV–vis spectra, cyclic voltammetry and chronoamperometry were conducted to characterize the prepared Au nanoparticle films.     

Label-free detection of specific DNA sequence-telomere using unmodified gold nanoparticles as colorimetric probes

A simple and sensitive label-free colorimetric detection of telomere DNA has been developed. It was based on the color change of gold nanoparticles (AuNPs) due to DNA hybridization. UV–vis spectra and transmission electron microscopy (TEM) were used to investigate the change of AuNPs. Under the optimized conditions, the linear range for determination of telomere DNA was 5.7 × 10⁻¹³ to 4.5 × 10⁻⁶ mol/L. The detection limit (3σ) of this method has decreased to pico-molar level.     

Novel potentiometric immunosensor for determination of diphtheria antigen based on compound nanoparticles and bilayer two-dimensional sol–gel as matrices

A novel method for fabrication of a diphtheria potentiometric immunosensor has been developed by means of self-assembling compound nanoparticles to a thiol-containing sol–gel network. A cleaned gold electrode was first immersed in a 3-mercaptopropyltrimethoxysilane (MPS) sol–gel solution to assemble a silica sol–gel monolayer. The silane entities were then polymerized into a two-dimensional sol–gel network (2D network) by dipping into aqueous NaOH. The second silane layer was formed by re-immersion in the MPS sol–gel solution overnight. The compound nanoparticles (nanocompounds) containing gold nanoparticles and silver nanoparticles were then chemisorbed on to the thiol groups of the second silane layer. Finally, diphtheria antibody (anti-Diph) was adsorbed on to the surface of the compound nanoparticles. The modified process was characterized by cyclic voltammetry (CV). Detection is based on the change in the potentiometric response before and after the antigen–antibody reaction. A direct potentiometric response to diphtheria antigen (Diph) was obtained from the immobilized diphtheria antibody. The potentiometric response of the resulting immunosensor was rapid and the linear range was from 22 to 800 ng mL^–1 with the linear regression equation E=–79.5+69.4 log [Diph] and a detection limit of 3.7 ng mL^–1 (at 3). Up to 19 successive assay cycles with retention of sensitivity were achieved for probes regenerated with 0.2 mol L^–1 glycine–hydrochloric acid (Gly–HCl) buffer solution. Moreover, analytical results from several serum samples obtained using the developed technique were in satisfactory agreement with those given by the ELISA method, implying a promising alternative approach for detecting diphtheria antigen in clinical diagnosis.     

Use of ICP and XAS to determine the enhancement of gold phytoextraction by <Emphasis Type="Italic">Chilopsis linearis</Emphasis> using thiocyanate as a complexing agent

Under natural conditions gold has low solubility that reduces its bioavailability, a critical factor for phytoextraction. Researchers have found that phytoextraction can be improved by using synthetic chelating agents. Preliminary studies have shown that desert willow (Chilopsis linearis), a common inhabitant of the Chihuahuan Desert, is able to extract gold from a gold-enriched medium. The objective of the present study was to determine the ability of thiocyanate to enhance the gold-uptake capacity of C. linearis. Seedlings of this plant were exposed to the following hydroponics treatment: (1) 5 mg Au L^–1 (2.5×10^–5 mol L^–1), (2) 5 mg Au L^–1+10^–5 mol L^–1 NH₄SCN, (3) 5 mg Au L^–1+5×10^–5 mol L^–1 NH₄SCN, and (4) 5 mg Au L^–1+10^–4 mol L^–1 NH₄SCN. Each treatment had its respective control. After 2 weeks we determined the effect of the treatment on plant growth and gold content by inductively coupled plasma–optical emission spectroscopy (ICP–OES). No signs of shoot-growth inhibition were observed at any NH₄SCN treatment level. The ICP–OES analysis showed that addition of 10^–4 mol L^–1 NH₄SCN increased the concentration of gold by about 595, 396, and 467% in roots, stems, and leaves, respectively. X-ray absorption spectroscopy (XAS) studies showed that the oxidation state of gold was Au(0) and that gold nanoparticles were formed inside the plants.     

Polyvinyl alcohol–ionic liquid composition for promoting the direct electron transfer and electrocatalysis of hemoglobin

The direct electron transfer and electrocatalysis of hemoglobin (Hb) entrapped in polyvinyl alcohol (PVA)–room temperature ionic liquid (i.e., 1-octyl-3-methylimidazolium hexafluorophosphate [OMIM]PF₆) composition has been investigated by using cyclic voltammetry and chronocoulometry. It is found that the composition can promote the direct electron transfer of Hb and the heterogeneous electron transfer rate constant (k_s) of immobilized Hb is enhanced to 19.9 s⁻¹. The immobilized Hb also shows high electro-catalytic activity towards the redox of oxygen, hydrogen peroxide and nitrite. The Michaelis constants (K_m) decrease to 1.2 × 10⁻⁴ M (for hydrogen peroxide) and 9.4 × 10⁻³ M (for nitrite). The surface concentration of electroactive Hb is estimated and it is ca. 1.4 × 10⁻¹⁰ mol cm⁻², meaning that several layers of immobilized Hb take part in the electrochemical reaction. When gold nanoparticles (GNP) is introduced into the composition, the resulting PVA–GNP–[OMIM]PF₆ composition presents better performance. The electrochemical characteristic of immobilized Hb is improved further. Thus PVA–GNP–[OMIM]PF₆ composition is more suitable for the immobilization of Hb. Therefore, it is a good strategy to prepare novel composition for protein immobilization by using several materials with different function.