磁场退火对Co基熔体抽拉丝巨磁阻抗效应的影响

对Co基熔体抽拉非晶丝进行了普通炉内退火和不同磁场强度（500 Oe,1600 Oe,4000 Oe）下的横向和纵向磁场退火,利用HP4192阻抗分析仪和Lakeshore7407VSM分析了退火态样品的巨磁阻抗（GMI）效应和软磁性能.研究结果表明,纵向磁场降低了环向各向异性,纵向磁场退火样品GMI效应降低且GMI曲线为单峰,最大阻抗变化率ΔZ/Z为131%,磁场响应灵敏度为7%/Oe;而横向磁场提高了环向畴体积,增加了环向各向异性场,导致退火样品GMI曲线随频率升高由单峰转 关键词： 非晶丝 巨磁阻抗效应 退火     

基于Nyquist图研究铁基非晶薄带巨磁阻抗效应的非线性

测量了铁基非晶薄带巨磁阻抗效应的阻抗实部和虚部并且计算出磁导率的实部和虚部,通过磁导率的非线性解释了巨磁阻抗效应的非线性原因,并且利用Nyquist图推出磁导率等效电路模型,指出磁导率等效电路模型中的LC共振频率是解决磁导率非线性的关键.研究结果表明:在激励电源横向磁化和外加磁场纵向磁化的过程中,非晶薄带磁导率的变化无规则,导致非晶薄带的巨磁阻抗效应呈现非线性变化.当激励频率在5 MHz、纵向磁场发生改变时,磁损耗角依然保持不变,磁导率与纵向磁场的非线性关系转化为磁导率模值与纵向磁场的关系,通过实验数据可以拟合出纵向磁场与磁导率的函数关系.     

非晶态合金磁阻抗效应的演示与实验

1992年,日本名古屋大学的mohir等在CoFeSiB软磁非晶丝中发现了巨磁阻抗效应,即当对软磁非晶丝通以交流电流时,细丝两端感生的交流电压随着丝纵向所加的一个很小的外磁场的变化而灵敏变化．随后,人们很快在同样为高磁导率的铁基纳米晶薄带、膜和丝中观察到了巨磁阻抗效应．利用该效应的灵敏度高、体积小、响应快等优点而开发出来的各种微型传感器,已广泛应用于微弱磁场的测量、     

NiFeCoP/BeCu复合结构丝的巨磁阻抗效应和磁化频率特性

用化学镀的方法制备了NiFeCoP/CuBe复合结构丝，研究了其巨磁阻抗特性.结果表明复合结构丝在较低频率的驱动电流下就有明显的磁阻抗效应，当驱动电流频率在20kHz时的磁阻抗效应为40％，最大磁阻抗效应出现的频率在180kHz，为97％.利用复数磁导率和等效电路探讨了该复合丝铁磁层磁化过程的频率特性，复合结构丝的特征弛豫频率在1MHz左右.外加直流磁场抑制畴壁移动，在等效电路中与抵消部分并联电路相关. 关键词： 巨磁阻抗效应 磁导率 弛豫频率 等效电路     

Co基金属纤维不对称巨磁阻抗效应

以直径32 μm的熔体抽拉Co基非晶金属纤维为研究对象, 分析了该纤维不同激励条件下的巨磁阻抗(giant magneto impedance, GMI)效应. 实验结果表明: 这类纤维的GMI效应具有不对称性特点, 即 AGMI (asymmetric GMI)效应. 同时, 发现AGMI效应随激励条件不同而变化, 随交流频率或者激励幅值升高而逐渐增强; 当存在一定偏置电压时, AGMI效应大幅增强. 通过研究纤维的磁化过程, 分析了Co基金属纤维的AGMI效应. 由于Co基熔体抽拉纤维具有螺旋各向异性以及磁滞的存在使得GMI效应具有不对称性, 频率升高或者激励电流幅值增加有利于壳层畴环向磁化, AGMI增强. 当在纤维两端施加偏置电压时, 偏置电流诱发环向磁场增强了环向磁化, AGMI效应提高; 偏置电压较低时磁场响应灵敏度提高, 同时磁化翻转向高场移动, 阻抗线性变化对应的直流磁场区间增大. 这一方面拓宽了GMI传感器工作区间及灵敏度, 另一方面不利于获得更大的磁场响应灵敏度. 10 MHz (5 mA)激励时, 施加1 V强度的偏置电压后, 对应的磁场灵敏度从616 V/T 提高至5687 V/T; 偏置电压为2 V时, 灵敏度降低到4525 V/T. 因此, 可以通过适当提高环向磁场的方法获得大的磁场响应灵敏度及阻抗变化线性区域.     

铁基软磁非晶/纳米晶合金研究进展及应用前景

非晶合金通常是将熔融的金属快速冷却、通过抑制结晶而获得的原子呈长程无序排列的金属材料.由于具有这种特殊结构,铁基软磁非晶合金具有各向同性特征、很小的结构关联尺寸和磁各向异性常数,因而具有很小的矫顽力H_c,但可和晶态材料一样具有高的饱和磁感强度B_s.优异的软磁性能促进了铁基软磁非晶合金的应用研究.目前,铁基软磁非晶/纳米晶合金带材已实现大规模工业化生产和应用,成为重要的高性能软磁材料.本文回顾了软磁非晶合金的发现和发展历程,结合成分、结构、工艺对铁基非晶/纳米晶合金软磁性能的影响,介绍了相关基础研究成果和工艺技术进步对铁基软磁非晶/纳米晶合金研发和工业化应用的重要贡献.并根据结构、性能特征将铁基软磁非晶合金研发与应用分为三个阶段,指出了目前铁基软磁非晶合金研发与应用中面临的挑战和发展方向.     

基于铁氧体基板的开口谐振环的可调微波左手特性研究

利用铁氧体的外场调制特性,提出采用铁氧体作为金属环线结构的介质基板,实现频率可调左手材料. 首先采用时域差分有限元方法数值模拟了基板材料参数变化的条件下,开口谐振环的频率可调性规律. 随基板材料的介电常数或磁导率升高,与开口谐振环负磁导率对应的透射谷频率将显著降低. 实验制备了一系列超高频软磁六角铁氧体,利用外加磁场有效调制了其磁导率. 并通过实验表明,通过调控外加磁场可以有效地调控开口谐振环负磁导率对应的透射谷频率. 关键词： 左手材料 开口谐振环 铁氧体 可调     

李萨如图形法测量软磁材料磁导率

提出了李萨如图形的一个新应用——测量软磁材料磁导率.实验系统由示波器和信号发生器构成,以安培环路定理及法拉第电磁感应定律为理论基础,利用李萨如图形实现了软磁材料磁导率的测量.实验结果给出了在材料未达到饱和磁化的情况下,不同励磁频率下的磁导率测量结果.     

纳米晶复合永磁材料的交换耦合相互作用和磁性能

本文介绍了纳米磁性材料晶粒交换耦合相互作用的有关理论。采用不同模型讨论了晶粒交换耦合相互作用对纳米单相软磁材料、永磁材料及双相复合永磁材料磁性能的影响。简述了用δM(H)曲线和不可逆磁导率的变化研究晶粒交换耦合相互作用及反磁化过程的方法。讨论了合金成分配比、添加元素、制备及热处理工艺对磁体硬磁性能的影响。从理论和实验两方面分析、研究了纳米复合永磁材料的反磁化过程和矫顽力机制。     

纳米晶复合永磁材料的交换耦合相互作用和磁性能

本介绍了纳米磁性材料晶粒交换耦合相互作用的有关理论。采用不同模型讨论了晶粒交换耦合相互作用对纳米单相软磁材料、永磁材料及双相复合永磁材料磁性能的影响。简述了用δM（H）曲线和不可逆磁导率的变化研究晶粒交换耦合相互作用及反磁化过程的方法。讨论了合金分配比、添加元素、制备及热处理工艺对磁体硬磁性能的影响。从理论和实验两方面分析、研究了纳米复合永磁材料的反磁化过程和矫顽力机制。     

Oscillatory magnetic anisotropy in one-dimensional atomic wires

One-dimensional Co atomic wires grown on Pt(997) have been investigated by x-ray magnetic circular dichroism. Strong changes of the magnetic properties are observed as the system evolves from 1D- to 2D-like. The easy axis of magnetization, the magnetic anisotropy energy, and the coercive field oscillate as a function of the transverse width of the wires, in agreement with theoretical predictions for 1D metal systems.     

巨磁阻抗效应实验研究

利用物理实验室中常见的设备,搭建了一组巨磁阻抗效应实验装置,测量了在不同轴向外磁场及不同频率下钴基非晶态软磁合金细丝的阻抗.阻抗实部虚部均随外磁场增大迅速减小,而随频率增大缓慢增大.与交流阻抗的电磁理论比较,该实验结果与理论一致.实验观察到在40 MHz的频率、10 mT外磁场中阻抗变化达80%.根据数据和理论公式拟合,发现材料复磁导率随磁场强度增大迅速减小.     

太赫兹波段谐振频率可调的开口谐振环结构

开口谐振环(SRRs) 结构可以激励磁谐振, 实现负的磁导率. 提出在SRRs两环间隙内引入相对交错的金属短线, 并研究了金属短线对谐振频率的影响. 结果表明: 随着金属短线数目的增多, 谐振频率显著降低, 同时金属短线的结构参数如长度、宽度及间距也会对谐振频率产生影响. 最后验证了金属短线的引入对减小器件尺寸有明显作用, 且不因介质基底的存在而受到影响. 新型磁谐振单元可为今后超材料的设计及实际应用提供新的参考. 关键词： 左手材料 开口谐振环 太赫兹 小型化     

Metamaterial composed of wire pairs exhibiting dual band negative refraction

The design of the metamaterial that can exhibit negative refraction at two frequency bands is presented. The components of this metamaterial are cut wire pairs and continuous wires. The cut wire pairs structure in our sample can achieve the magnetic resonance at two frequency bands by appropriately designing the cut wire dimension. Through numerical simulation, the transmission property of the proposed dual band negative index metamaterial is investigated and its result shows that with the introduction of continuous wires, the stop bands for cut wire pairs (permeability μ<0) and the frequency band for continuous wires (permittivity ε<0) components would overlap and lead to the appearance of pass bands near the two magnetic resonance frequency bands. Its electromagnetic properties are then retrieved to demonstrate that the dual band left-hand behavior can be obtained in our sample structure. It is believed that our approach will be effective to make this kind of dual band negative refractive metamaterial based on the multiple magnetic resonances work at optical frequency.     

Production of hot plasmas by hypervelocity impact

Very hot plasmas can be obtained by mutual collision of projectiles accelerated to high velocities up to 400 km/s. The electromagnetic drive of lithium or iron circular wires is considered by using either high frequency or constant magnetic fields. When deuterium and tritium are present, fusion reactions are expected. Considering iron, fusion could start from a temperature of 1.4/spl times/10/sup 6/ because energy has been released by the recombination of multiple charged ions.     

Magnetic spectra of Fe-based nanocrystalline wires with axial or transverse domains

The circular permeability μ′=μ′−jμ″ of two Fe-based soft magnetic wires with axial and transverse domains, has been determined from the measurements of impedance Z=R+jX as functions of frequency (f=10-10⁵ Hz) and AC current amplitude (I=0.1-100 mA). From the magnetic spectra of μ′−f and μ″−f for a few circular fields (H_φ=0.4, 1.2, 4, 12, 40 A/m), we found that the sample with axial domain structure exhibits a relaxational feature, while for the one with transverse domain resonance-like spectra were observed when the circular field H_φ≥4 A/m. These results have been discussed in terms of domain structure and circular magnetization processes.     

Effective magnetic properties of a composite material with circular conductive elements

Effective magnetic properties of a composite meta-material consisting of periodically arranged circular conductive elements are studied theoretically. A general expression for the effective bulk permeability is obtained with mutual effects and lattice ordering being taken into account. The resonance frequency of the permeability is found to be strongly dependent on the size and shape of the unit cell. Frequency dispersion of the permeability is studied with special attention paid to the frequency range, where negative values of the permeability are possible. Corresponding recommendations for optimisation of the meta-materials with negative permeability are made. The results are confirmed by numerical simulations of the finite structure behaviour in an external magnetic field. Received 19 April 2002 Published online 31 July 2002     

Microwave properties of composites with glass coated amorphous magnetic microwires

The complex permittivity and permeability of composites filled with Fe-based microwires are measured in a coaxial line at frequencies from 0.01 to 10 GHz.The samples under study consist of closely packed wire sections with various orientations relative to wave vector. The composites, where the wires are collinear to the coaxial axis, are found to be low permeable. Their permittivity has frequency dispersion governed by the length of the wire and its linear impedance. The middle section of the wire has higher impedance than that of the end sections where the regular domain structure is distorted. Magnetic bias parallel to the wire axis affects the linear impedance and parameters of dielectric absorption of a composite, the effect is proportional to bias strength. The samples of a coil-type structure, where the wires are wound around the coaxial axis, display the intensive magnetic absorption attributed to the domain wall motion. The absorption takes place in the megahertz band, at microwaves the permeability is close to unity. The microwave properties of diluted composites filled with randomly oriented permeable wires are discussed.