碘量法测定铜冶炼烟尘中铜含量

研究了铜冶炼烟尘中铜含量的测定方法,试料用盐酸、氢氟酸、硝酸、高氯酸及硫酸分解,氢溴酸除去砷、锡、锑,硫酸除去硒的干扰。进一步对滴定条件和共存元素的干扰及消除进行了实验,最终确定了最佳条件。按照实验方法测定6个铜冶炼烟尘样品中铜含量,结果的相对标准偏差为0.22%～0.65%,精密度高,准确度好。样品加标回收率在98.9%～100%,适用于铜冶炼烟尘中铜含量为5.00%～65.00%的样品测定。     

碘量法测定铜冶炼烟尘中铜

试验研究了铜冶炼烟尘中铜含量的测定方法,试料用盐酸、氢氟酸、硝酸、高氯酸及硫酸分解,氢溴酸除去砷、锡、锑,硫酸除去硒的干扰。进一步对滴定条件和共存元素的干扰及消除进行了试验,最终确定了最佳条件。按照实验方法测定6个铜冶炼烟尘样品中铜量,结果的相对标准偏差为0.22%~0.65%,精密度高,准确度好。样品加标回收率在98.92%~100.38%之间, 适用于铜冶炼烟尘中铜含量为5.00 %～65.00 %的测定。     

硫酸铅分离-EDTA滴定法测定铜闪速冶炼烟尘中的铅

建立了用硫酸形成硫酸铅沉淀加以分离,再用EDTA络合滴定法测定铜闪速冶炼烟尘中铅量的方法。试样用盐酸、硝酸、硫酸、氟化氢铵和高氯酸溶解,用硫酸沉淀铅与其它干扰元素分离,沉淀溶解于乙酸-乙酸钠缓冲溶液中,以巯基乙酸掩蔽铋,抗坏血酸掩蔽铁,二甲酚橙作指示剂,用Na2EDTA标准滴定溶液滴定溶液中铅含量,采用火焰原子吸收光谱法测定滤液中铅含量加以补正。实验结果表明,沉淀时硫酸(1+24)加入量为50 mL,无水乙醇加入量为10 mL,乙酸-乙酸钠缓冲溶液加入量为30 mL。方法相对标准偏差(RSD)在0.35%~1.5%,加标回收率为在99.0%~101%。完全满足生产控制分析的要求,同时也可以作为类似物料中铅分析的参考方法。     

硫酸铅分离-EDTA滴定法测定铜闪速冶炼烟尘中的铅

建立了用硫酸形成硫酸铅沉淀加以分离,再用EDTA络合滴定法测定铜闪速冶炼烟尘中铅量的方法。试样用盐酸、硝酸、硫酸、氟化氢铵和高氯酸溶解,用硫酸沉淀铅与其它干扰元素分离,沉淀溶解于乙酸-乙酸钠缓冲溶液中,以巯基乙酸掩蔽铋,抗坏血酸掩蔽铁,二甲酚橙作指示剂,用Na_2EDTA标准滴定溶液滴定溶液中铅含量,采用火焰原子吸收光谱法测定滤液中铅含量加以补正。实验结果表明,沉淀时硫酸(1+24)加入量为50mL,无水乙醇加入量为10mL,乙酸-乙酸钠缓冲溶液加入量为30mL。方法相对标准偏差(RSD)在0.35%～1.5%,加标回收率为在99.0%～101%。完全满足生产控制分析的要求,同时也可以作为类似物料中铅分析的参考方法。     

溴酸钾滴定法测定铜冶炼烟尘中的砷含量

研究了测定铜冶炼烟尘中砷含量的溴酸钾滴定方法。对测定体系中的各共存元素进行研究,探讨了测定方法的各项测定条件,方法的相对标准偏差RSD为0.13%～0.61%,样品加标回收率在99.5%～100%,方法精密度高,准确度好,适用于铜冶炼烟尘中砷含量为1.00%～50.00%的测定。     

火焰原子吸收光谱法测定铜冶炼烟尘中铋

本文研究了测定铜冶炼烟尘中铋含量0.050% ~5.00%的火焰原子吸收光谱法。对铜冶炼烟尘试样的溶解、测定体系中酸介质的影响和各干扰元素进行了试验研究。制定了铜冶炼烟尘中铋含量的原子吸收光谱法。方法标准偏差为0.0013 %~ 0.057 %,相对标准偏差为0.78 % ~1.44 %,样品加标回收率为98.95%~101.87%。本方法具有灵敏度高、结果准确、操作简便等特点,适合铜冶炼烟尘中铋含量0.050 % ~ 5.00 % 的测定。     

Na2EDTA滴定法测定铜冶炼烟尘中铋含量

研究了测定铜冶炼烟尘中铋含量的Na_2EDTA络合滴定方法。对测定体系中的各干扰元素进行了研究,探讨了测定方法的各项测定条件。方法的相对标准偏差为0.40%～0.67%,样品加标回收率在99.9%～100%,方法精密度高,准确度好。适用于铜冶炼烟尘中铋含量为5.00%～16.00%的测定。     

碱熔酸浸试样–碘量法测定铜冶炼白烟尘中的铜

建立碱熔酸浸试样–碘量法测定铜冶炼白烟尘中铜的方法。采用氢氧化钾–硝酸钾混合溶剂熔融试样,用盐酸浸取,以溴消除砷、锑等元素的干扰,用碘量法测定铜的含量。对滴定条件及共存元素的干扰和消除进行了验证,从而确定了最佳测定条件。实验最佳条件:4 g氢氧化钾和0.5 g硝酸钾混合溶剂;马弗炉温度650 ℃;样品称样量0.300 0 g;硫代硫酸钠标准溶液浓度0.02 mol/L。采用该实验条件,铜冶炼白烟尘中的铜测定结果相对标准偏差在0.37%~0.83%之间(n=10),样品加标回收率为98.30%~101.40%。该方法分析时间短,测定结果准确可靠,具有良好的精密度,可用于铜冶炼白烟尘中铜的测定。     

电感耦合等离子体光谱法测定铜冶炼烟尘中锌

本实验介绍了电感耦合等离子体光谱法测定铜冶炼烟尘中锌含量的分析方法。针对样品碳,硅含量高的特点,有针对性的研究了样品的消解方法,确定采用盐酸、硝酸、氢氟酸、高氯酸对铜冶炼烟尘样品进行消解。同时进行了干扰试验,确定样品中高含量的铜,铅,砷等对样品测定结果没有影响。并对仪器的工作参数进行了优化。方法检出限为为0.011 mg/L,测定下限为0.019 mg/L,3个样品的相对标准偏差在0.54%~0.92%之间,加标回收率在96%~101.14%之间。该方法样品消解完全,流程短,操作简单,快速,测定准确度高,可以满足铜冶炼烟尘中锌含量的测定。     

沉淀分离-EDTA滴定法测定铜闪速冶炼烟尘中的锌量

称取0.5 g试样,用盐酸、硝酸、硫酸分解,铅以硫酸铅沉淀的形式分离.以过硫酸铵为氧化剂,氨性溶液中沉淀分离铁、锰等共存元素,加氟化物掩蔽铝、硫脲掩蔽铜,调节溶液pH=5.0～6.0,加入碘化钾消除镉的干扰,以二甲酚橙为指示剂,用ED TA标准溶液滴定.将沉淀物重新溶解,用原子吸收光谱法测定其中的锌量.在0.2％ ～1...     

二硫化碳对机体铜、锌水平的影响

为观察二硫化碳（CS2）对机体铜，锌水平的影响，对某化纤厂35名接触CS2工人和41名非接触工人的血铜，锌值进行调查，比较，并进行了动物染毒实验。SD大鼠吸入CS2浓度分别为5和50mg/m^3，每日5h，每周6d，连续6个月，于染毒2，4，6个月时测定血浆铜，锌值及染毒6个月时肝脏铜，锌含量。结果显示，CS2接触组工人血铜，锌水平较对照组显著降低（P＜0．05）。在CS2染毒6个月时，50mg/m^3 CS2染毒组血浆及肝脏铜水平均较对照组及5mg/m^3 CS2染毒组显著降低（P＜0．05）。可见接触CS2能干扰机体铜，锌代谢，导致体内铜，锌含量减少。     

Sensitive and Profitable Electrochemical Detection of Uric Acid in the Presence of Dopamine with a Novel Carbon Paste Electrode Decorated with a Copper(II) Complex

A new microcomposite with copper(II) complex and carbon paste (Cu_C/CPE) was developed to determine the uric acid (UA) content in the presence of dopamine (DP) and was characterized via cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and energy dispersive spectroscopy (EDS). The results showed high selectivity for UA compared with DP because the anodic peak currents for DP were near those of a CPE without Cu_c and were considerably increased for UA. The UA and DP increases were 86.9 % and 14.3 %, respectively, according to CV and 96.6 % and 25.5 %, respectively, according to square wave voltammetry (SWV) with the Cu_C/CPE. Moreover, the anodic peak separation for UA and DP was 0.17 V. With optimal parameters (pH, 3.3; adsorption time(t_ADS), 30 s;adsorption potential (E_ADS)_, 0.10 V), the anodic peak currents for UA were proportional to concentrations between 1.6 and 14.4 μmol L^?1 using standard solutions with UA concentrations ranging from 8.0–40.5 μmol L^?1 and real samples. The UA detection limit was 0.13 μmol L^?1. The new sensor was used to determine the UA contentin human urine samples, and the method was checked with a urine chemistry control from Bio‐Rad based on human urine spiked with quantities of UA and showed a recovery between 84 % and 106 % at concentrations below 10.0 μmol L^?1.     

肝炎患儿发锌,铜,铅,镉含量的分析

采用闰溶出法测定８２例肝炎患儿的头发中锌,铜,铅,镉含量。结果显示,大多数急,慢性肝炎患儿发锌含量降低;发铜增高者仅占１／４和１／８,肝慢性肝炎中发铜降低者红占１／３,为急性肝炎的３倍;     

A Study on the Suitability of Carbon Disk Microelectrodes for Trace Analysis of Lead and Copper by ASV

The performance of carbon microdisk electrodes for the simultaneous trace analysis of lead and copper by anodic stripping voltammetry is investigated. The evaluation of the two metal ions in a single step, i.e., by employing a plating potential at which both cations are reduced simultaneously, gives unpredictable results due to the interaction between lead and copper deposited onto the electrode surface. In particular, the calibration plots of lead are not linear, while the copper stripping peak is quite broad and irreproducible. A two-steps deposition procedure, based on a preelectrolysis of copper performed at a potential at which lead ion is not reduced, followed by a simultaneous reduction of the two cations at large enough negative potentials, provides, instead, linear calibration graphs for lead. Copper can be determined without interference by plating the metal at a negative potential where lead ion is not reduced. The reliability of the two-steps procedure for the determination of lead and copper is verified in rain and wine samples.     

Influence of Plasma Treatment on the Electroless Deposition of Copper on Carbon Fibers

Air and nitrogen glow discharge were used to replace chromic acid pretreatment to deposit copper film on carbon fiber surfaces from an CuSO₄‐HCHO electroless system. A greater copper uptake and a more uniformly coated copper film were obtained for plasma‐treated carbon fibers. The adhesion between the copper film and the carbon fibers was also improved. An orthogonal table L₉(3⁴) was used to study the effects of discharge pressure, discharge power, time and gas type on the copper uptake. Scanning electron microscopy (SEM), reflection absorption infrared spectroscopy (RAIR) and X‐ray photoelectron spectroscopy (XPS) at different depths were applied to characterize the physical and chemical changes of the surface of the carbon fibers. The results showed that after plasma treatment, the carbon fiber surface became rough and several types of polar oxygen groups, such as carboxylic acid COOH, esters COOC, quinones Ph?O, etc., were introduced into the carbon fiber surface. A mechanism of plasma treatment effects on copper electroless deposition on the carbon fiber surface is also suggested.     

基于多壁碳纳米管/纳米铜复合材料的电化学传感器测定槐米中芦丁

以Nafion-多壁碳纳米管(MWNTs)薄膜修饰玻碳电极,采用恒电位法在其表面电沉积纳米Cu,研制了一种新型的芦丁电化学传感器。采用循环伏安法和电化学阻抗谱研究传感器在铁氰化钾-亚铁氰化钾体系中的电化学行为,以考察传感器的电化学性能,采用扫描电镜对传感器表面的形态进行了研究,并利用差分脉冲伏安法测定芦丁的含量。实验结果表明,该传感器对芦丁有较好的催化作用。在优化实验条件下,对芦丁检测的线性范围为1.0×10-8~1.0×10-6 mol/L,检出限为8.4×10-9 mol/L(S/N=3),回收率为98.1%~101%,该传感器制作简单,线性范围宽,灵敏度高,为槐米等样品中芦丁含量的检测提供了一种新的、行之有效的方法。     

Microwave Assisted Digestion Method for the Determination of Cadmium,Copper, Lead,and Zinc in Biological Materials

Anodic stripping voltammetry is useful instrumental method for trace element determination in biological materials. It is however extremely demanding to the quality of the sample preparation process. The high‐pressure microwave assisted digestion seems to meet its requirements. The differential pulse anodic stripping voltammetry technique was used for determination of cadmium, copper, lead and zinc in certified reference materials both of plant and of animal origin to prove the analytical properties of such sample preparation method. The found concentrations have been in satisfactory agreement with the certified values. The elaborated digestion procedure is greatly universal and has required accuracy and precision.     

Determination of Copper,Cadmium and Lead in Zinc Metal by Preconcentration onto Activated Carbon Combined with Direct Current Arc Atomic Emission Spectrography

Abstract

A preconcentration method is described for traces of copper, cadmium and lead from pure zinc metal by use of activated carbon. Ammonium salt of dithiophosphoric acid-o, o-diethylester is used to complex Cu, Cd and Pb. These chelates are sorbed on activated carbon. The traces sorbed on the carbon are determined by direct current arc atomic emission spectrography. The analytical error in the concentration range of 10^?3–10^?4% is less than 6% and relative standard deviation is below 10%.