毛细管电泳多道电化学检测器的研制及其应用

报道了毛细管电泳多道电化学检测器的研制及其应用，安培检测器和电导检测器并联在同一毛细管电泳检测系统中，在同一缓冲体系，同一工作电极下对同一复杂的分析体系同时进行电导和安培检测；整个装置综合了电导检测和安培检测两种检测器的优点，性能优良，造价低廉，对实际样品的检测取得了令人满意的结果。     

用于高效毛细管电泳的电化学检测器

阐述了高效毛细管电泳电化学检测器（包括电导、电势和安培检测）的研究现状，重点是检测器的研制及接口的制作技术。对各种电化学检测器的应用情况也进行了总结。展望了高效毛细管电泳电化学检测的发展前景。     

电化学检测离子色谱法分析卤离子的研究

自离子色谱法问世以来,已被广泛应用于微量卤离子的分析,但多用电导检测器检测。近几年来Dionex公司提出了电化学检测器测定卤离子可获得比电导检测更高的灵敏度。为了进一步开发应用,有必要研究有关电化学检测时离子色谱的行为。本文应用银工作电极的电化学检测器研究了氯离子和溴离子的离子色谱,考察了氯和溴离子色谱中负峰的性质,提出应用电化学检测器和电导检测器同时进行测定不同数量级的卤离子的可能性。     

微芯片毛细管电泳电化学检测方法及应用

阐述了微芯片毛细管电泳电化学检测(包括安培法、电导法、电化学发光法和联用电化学法)的研究进展；对各种电化学检测的原理和应用进行了较详细的叙述；着重讨论了不同材料检测电极在安培检测中的应用；接触式电导和非接触式电导的应用情况；展望了微芯片毛细管电泳电化学检测的前景。引用文献87篇。     

毛细管电泳-荧光/非接触电导组合型检测器的研制

报道了一种毛细管电泳-荧光／非接触电导组合型检测器。该检测器共用非接触电导检测池,实现了双检测器响应同步。优化了非接触电导检测系统中激发电压信号及其频率;荧光检测是用发光二极管作为激发光源,用光纤收集并传输荧光信号至光电倍增管。用无机金属离子和异硫氰酸荧光素评价该体系,结果表明,该检测器达到了任一单类型检测器性能指标。     

电泳芯片无接触电导检测器的理论研究

目前电泳芯片大多数采用的是光学检测的方法,这为电泳芯片的微型化、一体化集成带来了一定的难度。为此,设计了一种新的电泳芯片高频无接触电导检测器,并对这种新型的检测器进行了理论研究和分析,建立了高频电导检测器等效电路模型,对高频电导检测器的结构进行了设计;综合考虑区带展宽等因素,确定了检测器的结构尺寸。该检测器具有应用范围广、结构简单、易于一体化集成的特点。     

一种新型毛细管电泳双圆盘电极电导检测池

研制厂一种新型双凼盘电极毛细管电泳电导检测池。从理论和实验上分析验证了电导池参数、电导池位置对检测器性能的影响该检测池不仅结构简单、易于制作，而且极大地减小了柱外区带展宽，消除了高电压对检测器的影响，获得了较高的分离效率和信噪比采用Li^＋、Na^＋、K^＋的混合物对该检测池的性能进行了测试在最佳实验条件下，其俭出限分别为5．1、3．9和2．3μmol／L。     

毛细管电泳电化学检测

综述了毛细管电泳的电化学检测,包括电位法、电导法和安培法检测的研究进展,重点讨论了电化学检测与毛细管电泳的耦联,并对电化学检测的原理及其应用进行了较详细的叙述,引用文献72篇。     

高效离子交换色谱-电化学检测法测定药物合成中间体中的6-磷酸甘露糖

在制备6-磷酸甘露糖过程中,将6-磷酸甘露糖与磷酸根杂质分开是纯化过程和建立质量标准的重要环节。本文建立了6-磷酸甘露糖和磷酸根的离子色谱分离-电化学检测方法。样品经溶解、过滤后进行色谱分析,以IonPac AG18离子交换柱(50 mm×4 mm)为保护柱,在Ionpac AS18离子交换色谱柱(250 mm×4 mm)上分离,以25 mmol/L氢氧化钾溶液为流动相,等度淋洗,流速1.0 mL/min,安培检测器和电导检测器串联检测,外标法定量。先使用安培检测器检测,在碱性条件下,6-磷酸甘露糖在安培检测器上被选择性检出;后使用电导检测器检测,经ASRS型抑制器抑制背景电导后,6-磷酸甘露糖和磷酸根同时被电导检测器检出,二者分离度良好。采用安培检测器检测时,进样量为25 μL, 6-磷酸甘露糖的线性范围为0.06～10.00 mg/L,相关系数为0.9998,回收率为92.1%～103.1%,相对标准偏差均小于3%,检出限(以信噪比为3计)为0.02 mg/L。该方法灵敏度高,无杂质干扰,前处理简便,可用于原料药合成中间体的检测,结果令人满意。     

高效液相色谱讲座(Ⅳ) 检测器(下)

4-4 电化学检测器 在液相色谱中对那些没有紫外吸收或不能发出荧光但具有电活性的物质,可采用电化学检测法。目前电化学检测器主要有四种类型:极谱、安培、库仑和电导检测器。若在分离柱后采用柱后衍生技术,还可将它扩展到非电活性物质的检测。它已在各种有机和无机阴、阳离子、组织和体液中的代     

Electrochemical detection on electrowetting-on-dielectric digital microfluidic chip

In this work, the use of three-electrode electrochemical sensing system with an electrowetting-on-dielectric (EWOD) digital microfluidic device is reported for quantitative analysis of iodide. T-junction EWOD mixer device was designed using arrays of 50-μm spaced square electrodes for mixing buffer reagent and analyte droplets. For fabrication of EWOD chips, 5-μm thick silver EWOD electrodes were formed on a glass substrate by means of sputtering and lift-off process. PDMS and Teflon thin films were then coated on the electrodes by spin coating to yield hydrophobic surface. An external three-electrode system consisting of Au working, Ag reference and Pt auxiliary wires were installed over EWOD electrodes at the end of T-junction mixer. In experiment, a few-microliter droplets of Tris buffer and iodide solutions were moved toward the mixing junction and transported toward electrochemical electrodes by EWOD process. A short processing time within seconds was achieved at EWOD applied voltage of 300 V. The analyte droplets mixed with different concentrations were successfully analyzed by cyclic voltametry. Therefore, the combination of EWOD digital microfluidic and electrochemical sensing system has successfully been demonstrated for rapid chemical analysis with minimal reagent consumption.     

A New Dual-electrode and Multi-channel Electrochemical Detection System for Capillary Electrophoresis

A new type of dual-electrode and multi-channel electrochemical detection technology for capillary electrophoresis is described in this paper.Two detectors(the amperometric detector and the conductometric detector) or two conductometric detectors are connected to the same capillary electrophoresis system.The whole system possesses the advantages of the two electrochemical detectors including sparing time,improving the analytical speed and expanding the sample range.The working electrode and detector cell are handled easily.The system was applied to sample detection with satisfactory results.     

AAO-CNTs electrode on microfluidic flow injection system for rapid iodide sensing

In this work, carbon nanotubes (CNTs) nanoarrays in anodized aluminum oxide (AAO-CNTs) nanopore is integrated on a microfluidic flow injection system for in-channel electrochemical detection of iodide. The device was fabricated from PDMS (polydimethylsiloxane) microchannel bonded on glass substrates that contains three-electrode electrochemical system, including AAO-CNTs as a working electrode, silver as a reference electrode and platinum as an auxiliary electrode. Aluminum, stainless steel catalyst, silver and platinum layers were sputtered on the glass substrate through shadow masks. Aluminum layer was then anodized by two-step anodization process to form nanopore template. CNTs were then grown in AAO template by thermal chemical vapor deposition. The amperometric detection of iodide was performed in 500-μm-wide and 100-μm-deep microchannels on the microfluidic chip. The influences of flow rate, injection volume and detection potential on the current response were optimized. From experimental results, AAO-CNTs electrode on chip offers higher sensitivity and wider dynamic range than CNTs electrode with no AAO template.     

Electrochemical Detection Using an Engraved Microchip – Capillary Electrophoresis Platform

The present study describes a simple strategy to integrate electrochemical detection with an assembled microchip‐capillary electrophoresis platform. The electrochemical cell was integrated with a microfluidic device consisting of five plastic squares interconnected with fused silica capillaries, forming a four‐way injection cross between the separation channel and three side‐arms (each of 15 mm in length) acting as buffer/sample reservoirs. The performance of the system was evaluated using electrodes made with either carbon ink, carbon nanotubes, or gold and under different experimental conditions of pH, capillary length, and injection time. Using this system it was possible to separate the neurotransmitters dopamine and cathecol and to quantify phenol from a real sample using a linear calibration curve with a calculated LOD of 0.7 µM. A similar concept was applied to determine glucose, by including a pre‐reactor filled with beads modified with glucose oxidase (GOx). The latter system was used to determine glucose in a commercial sample, with a recovery of 95.2 %. Overall, the presented approach represents a simple, inexpensive, and versatile approach to integrate electrochemical detection with CE separations without requiring access to microfabrication facilities.     

Integrated explosive preconcentrator and electrochemical detection system for 2,4,6-trinitrotoluene (TNT) vapor

This article reports on an integrated explosive-preconcentration/electrochemical detection system for 2,4,6-trinitrotoluene (TNT) vapor. The challenges involved in such system integration are discussed. A hydrogel-coated screen-printed electrode is used for the detection of the thermally desorbed TNT from a preconcentration device using rapid square wave voltammetry. Optimization of the preconcentration system for desorption of TNT and subsequent electrochemical detection was conducted yielding a desorption temperature of 120 °C under a flow rate of 500 mL min⁻¹. Such conditions resulted in a characteristic electrochemical signal for TNT representing the multi-step reduction process. Quantitative measurements produced a linear signal dependence on TNT quantity exposed to the preconcentrator from 0.25 to 10 μg. Finally, the integrated device was successfully demonstrated using a sample of solid TNT located upstream of the preconcentrator.     

Chronoamperometry Measurement for Rapid Cucumber Mosaic Virus Detection in Plants

Cucumber mosaic virus (CMV) causes major losses to agricultural and horticultural crops around the world. Hence, a rapid assay for the detection of CMV which can be employed in both laboratory and field is essential. A portable electrochemical immunosensor system for the detection of CMV, based on immobilized CMV specific antibodies conjugated with gold nanoparticle was developed for this purpose. The conjugated antibodies were added with polymer and deposited onto carbon screen printed working electrodes. Optimization of the modified surface immunosensor was performed using sandwich immunoassay format (ELISA). The initial ELISA result for the standard curve development showed a limit of detection down to 0.1mg/mL. Subsequently, the immunosensor was tested for cross reactivity with other plant pathogens. The performance of the electrochemical immunosensor revealed that it has a high selectivity in sample matrix with other organism. This immunosensor provides a promising technology for simple and sensitive detection system that is essential in rapid detection of plant pathogens.     

On-chip type cation-exchange chromatography with ferrocene-labeled anti-hemoglobin antibody and electrochemical detector for determination of hemoglobin A1c level

An on-chip type cation-exchange chromatography system with electrochemical detection of HbA_1c, which is one of the most important diabetes marker protein, was developed using ferrocene-conjugated anti-human hemoglobin (Hb) monoclonal antibody (FcAb). The FcAb was used as an electrochemical probe for the detection of each Hb. The system contains syringe pump, on-chip type cation-exchange column consisted of PDMS and cation-exchange resin beads, and a three-electrode flow-cell system. The separation conditions of HbA_1c in blood calibrator samples from other Hbs, e.g. HbA₀, HbA_1a or HbA_1b, were optimized using the on-chip type system. The electrochemical oxidation current from FcAb reacting with each Hb was measured at 350 mV (vs. Ag/AgCl). Hbs including HbA_1a and HbA_1b, HbA_1c and HbA₀ fractions were eluted in this order. A linear relationship between HbA_1c levels and electrochemical oxidation currents was obtained in the range from 4.0% to 12.6% HbA_1c. All procedure including antigen-antibody reaction was completed in 15 min. Furthermore, a good correlation was obtained between KO500 method (HPLC) and our proposed method. These results indicate that the on-chip type system with electrochemical detection can be applied to a novel POCT device for rapid and precise detection of HbA_1c.     

Droplet-based microfluidics for dose–response assay of enzyme inhibitors by electrochemical method

A simple but robust droplet-based microfluidic system was developed for dose–response enzyme inhibition assay by combining concentration gradient generation method with electrochemical detection method. A slotted-vials array and a tapered tip capillary were used for reagents introduction and concentration gradient generation, and a polydimethylsiloxane (PDMS) microfluidic chip integrated with microelectrodes was used for droplet generation and electrochemical detection. Effects of oil flow rate and surfactant on electrochemical sensing were investigated. This system was validated by measuring dose–response curves of three types of acetylcholinesterase (AChE) inhibitors, including carbamate pesticide, organophosphorus pesticide, and therapeutic drugs regulating Alzheimer's disease. Carbaryl, chlorpyrifos, and tacrine were used as model analytes, respectively, and their IC₅₀ (half maximal inhibitory concentration) values were determined. A whole enzyme inhibition assay was completed in 6 min, and the total consumption of reagents was less than 5 μL. This microfluidic system is applicable to many biochemical reactions, such as drug screening and kinetic studies, as long as one of the reactants or products is electrochemically active.     

毛细管电泳-柱端电化学检测池的设计

在射壁式检测器的基规上,设计了一种用于毛细管电泳-电化学检测装置的检测池,巧妙地利用因表面张力现象而留驻波滴曲面的放大作用,直接调整毛细管与电极之间的相对位置,无需显微镜-微调节器装置,具有空间体积小,操作更简便的优点。     

集成化金膜阵列电极的制作研究

以聚乙烯不干胶掩膜版法结合金属溅射沉积技术在FR-4玻璃纤维版上制作了由6个金膜工作电极(1 mm×2 mm)、1个大面积金膜对电极(2 mm×13 mm)和1个厚膜Ag/AgCl参比电极构成的集成化金膜阵列电极系统,并利用电化学手段对阵列电极系统进行了考察。研究结果表明,K3Fe(CN)6在厚膜Ag/AgCl/1.0 mol/L NaCl参比电极上的式电位与商业Ag/AgCl/3.0 mol/L NaCl参比电极相差0.067 V;参比电极放置1个月后,测量电位未发生明显变化。利用扫描电化学显微镜对工作电极表面平整度进行考察,结果表明工作电极表面具有较好的平整度。通过测量H2SO4还原峰面积评价了工作电极电化学面积的批内、批间一致性;通过K3Fe(CN)6在电极上的Ipa/Ipc比值评价了工作电极电化学特性的批内、批间一致性。结果表明,阵列电极面积和电化学特性具有良好的批内和批间一致性。对集成化金膜阵列电极系统的研究结果表明,聚乙烯不干胶掩膜版法结合金属溅射沉积技术制作的阵列电极能够满足电化学电极的要求,可作为电化学生物传感器的基础电极。