程序升温焙烧技术研究水滑石热分解动力学

催化剂前体一般为硝酸盐、碳酸盐、草酸盐和水滑石等易热分解的化合物,经过干燥、高温焙烧以及还原、活化处理后,得到催化剂的活性组分。焙烧条件的选择是催化剂制备过程中的重要环节,一般采用ＴＧＤＴＡ分析来确定［１］。高温下有些载体分子内失水以及含结晶水的前体,在不同温度下水的逐步脱除会使ＴＧＤＴＡ曲线变得复杂,影响对这些化合物本身热分解动力学的计算。程序升温焙烧（ＴＰＣ）技术是一种比较简易、方便的实验方法［２］,可以灵敏、直观地研究催化剂前驱体的热分解过程并进行动力学计算。水滑石（ｈｙｄｒｏｔａｌｃ…     

含铜类水滑石催化材料热分解过程的研究

共沉淀法合成了Cu0.13Mg0 6Al0.27(OH)2(CO3)0.135·xH2O类水滑石物质 (CuHTlc) ,采用XRD、DTA TG、BET、TEM和27AlMASNMR技术对其热分解过程进行了表征。结果表明 ,在较低焙烧温度时 (低于300℃ ),氢氧根和层间水部分脱除 ,但水滑石仍保持其层状结构 ;500℃时 ,其层状结构被完全破坏 ,出现氧化镁晶相结构 ,随着焙烧温度的进一步升高 ,尖晶石晶相生成。500℃时的焙烧产物具有最大比表面 (193m2·g-1)。当温度高于500℃ ,焙烧产物组成可表示为Cu0.13Mg0.6Al0.27O0.135,CuHTlc的热分解过程可表示为 :Cu0.13Mg0.6Al0.27(OH)2(CO3)0.135·xH2O→Cu0.13Mg0.6Al0.27O0.135 (1 x)H2O 0.135CO2。     

镧掺杂水滑石材料的热分解过程研究

采用共沉淀法制备了系列La掺杂改性的含Cu类水滑石,高温焙烧得到其衍生混合氧化物材料,并用XRD,TG-DSC,FT-IR等对材料进行表征.结果表明,前驱物XRD图谱呈典型的水滑石衍射特征且颗粒结晶良好;经800℃焙烧后,掺杂La2O3含量为5.1%的样品仅有Mg1-xFexO晶相出现,说明La的掺杂提高了材料的高温稳定性,混合氧化物中的Cu离子呈高分散状态.     

Mg/Zn/Al类水滑石的热分解和水化性能研究

采用共沉淀法制备了Mg2Al1、Zn2Al1和Mg1Zn1Al1LDHs,利用XRD和SEM表征手段,对它们的热分解及焙烧物在Na2CO3溶液中恢复层状结构的能力进行了对比研究。结果表明,在400～700℃温度范围内,Zn2Al1LDH和Mg2Al1LDH的焙烧物中均出现氧化物相(ZnO和MgO)和尖晶石相(ZnAl2O4和MgAl2O4相);而Mg1Zn1Al1LDH的焙烧物中始终以ZnO相为主,仅在700℃时出现微弱的MgAl2O4相。三种焙烧物恢复层状结构的能力为:Mg1Zn1Al1LDO>Mg2Al1LDO>Zn2Al1LDO,其与焙烧物组成有关。原始LDHs和水化LDHs均呈片状。     

二水草酸亚铁热分解行为及脱水反应动力学研究

The thermal behavior of ferrous oxalate dihydrate (FeC₂O₄·2H₂O) was studied by thermogravimetry and differential thermal analysis (TGA and DTA). Three steps could be deduced for the decomposition from the TG,DTG and DTA curves obtained. One of the steps was the dehydration, the mass loss was 20.1%(the found value was in good agreement with the calculated value). Mathematical analysis with the integral and differential methods showed that the kinetics of dehydration of FeC₂O₄·2H₂O could be explained by F1 mechanism in nitrogen atmosphere. The kinetic equation of dehydration of FeC₂O₄·2H₂O could be expressed as: dα/dt=6.25×10¹⁹[exp(-170.27×10³/RT)](1-α)     

Cu/Co/Fe水滑石衍生的复合氧化物催化高氯酸铵热分解的研究

以Cu/Co/Fe水滑石(Cu/Co/Fe-LDHs)为前驱体经过焙烧制备了Cu/Co/Fe复合氧化物(Cu/Co/Fe-MOs)。利用DTA和TG-MS研究了Cu/Co/Fe-MOs作为新型催化剂对高氯酸铵热分解的催化性能。结果表明,Cu/Co/Fe-MOs呈现为CuFe2O4和(CoFe2)O4晶相,具有70~110 m2.g-1的比表面积。晶粒大小均匀,尺寸在20~30 nm。添加4wt%的400℃焙烧得到的Cu/Co/Fe-MOs催化剂使高氯酸铵热分解反应的温度降低了139℃。Cu/Co/Fe-MOs是通过吸附在金属氧化物表面的超氧离子(O2-)来加速高氯酸铵热分解的。     

硫化氢热分解制氢过程的化学动力学研究

采用化学热平衡分析方法研究了硫化氢热分解制氢过程,研究了硫化氢在不同温度和体积分数下的分解过程,并与试验数据进行了比较。结果表明,基元反应机理能较好地模拟硫化氢热分解制氢过程。硫化氢的热分解率依赖于反应温度,高温下能获得较好的分解制氢效果;温度较低时,时间是硫化氢趋于平衡的主要影响因素,随着温度的提高,温度成为影响硫化氢趋于平衡的主要影响因素。硫化氢初始体积分数对热分解制氢反应具有较大的影响,采用较低体积分数的硫化氢混合气有利于获得高的硫化氢热分解制氢率。     

氟碳铈矿热分解动力学研究

采用Harcourt-Esson方法对不同来源的氟碳铈矿晶体热分解动力学进行了系统研究，得到的反应机制方程用普适积分法进一步验证，结果显示微山矿热分解为一级反应，不同品位的冕宁、非洲、芒廷帕斯氟碳铈矿热分解反应都是按照三维扩散机制进行的。     

Mg-Al-CO3与Zn-Al-CO3水滑石热稳定性差异的研究

层状双金属氢氧化物（Ｌayered double hydroxides,简称ＬＤＨs）是一种类近年来发展迅速的阴离了型粘土,又称水滑石,其组成通式为[M（II）1－xM(III)x(OH)2]x(OH)2]^x＋Ax/n^n-mH2O,其中M（II）是二介金属离子,M（III）是三价金属离子,A^n-是阴离子,这种材料是由相互平行的层板组成,层板带有永在电荷,层间具有可交换的阴离子以维持电荷平衡,通过离子交换可在层间嵌入不同的基团,制备许多功能材料,被广泛作催化剂、吸附剂及油田化学品等,已引起人们的关注^[1-4]。有关Mg-Al-CO3与Zn-Al-CO3水滑石的合成及性能研究国内外已有大量报道^[1,2],本文对两者热稳定性存在的差异进行了研究,这对深化此类材料的认识具有参考作用。     

二水草酸亚铁热分解反应动力学

用原位XRD技术和热重法分析了二水草酸亚铁的热分解过程, 并进行了动力学研究. 通过结合主曲线法和统计方法判定了热分解过程的动力学模型函数, 并求算了动力学参数. 在静态自产气氛下, 二水草酸亚铁脱水反应遵循随机成核与核增长模型, 草酸亚铁热分解生成氧化铁遵循相界面控制动力学模型. 结果表明, 该方法可以准确、可靠地判定非等温热分解反应的动力学模型函数,并求算动力学参数.     

Kinetics of thermal decomposition of nickel sulfate hexahydrate

The paper describes the kinetics of all the recorded steps of thermal decomposition of nickel sulfate hexahydrate in air. The thermal decomposition of the salt in air led to NiO at about 1060 K. The kinetic parameters, the activation energyE and the preexponential factorA, and the thermodynamic parameters, the entropy, enthalpy and free energy of activation were evaluated for the dehydration and decomposition reactions. Tentative reaction mechanisms are suggested for each step of the thermal decomposition.     

氢氧化镁分解动力学的研究

以硼泥为原料与硫酸反应制备出七水硫酸镁,以氢氧化钠为沉淀剂制备出符合标准HG/T 3607-2000的氢氧化镁.利用XRD,SEM和TEM对氢氧化镁进行了表征,DTA-TG对氢氧化镁的热分解动力学进行了研究.XRD结果表明:制备粉体为单一Mg(OH)2.SEM和TEM结果表明:样品为片状或针状纤维,片直径大小不一,在20～50 nm之间,针状纤维形状不规则,大小不一致,长度在20～100 nm之间.利用Kissinger法和Ozawa法计算出的氢氧化镁热分解反应活化能分别为135.14和141.61 kJ·mol-1.利用Coats-Redfern法和Dolye法判断氢氧化镁热分解反应机理函数为A1.5.     

Kinetics of decomposition of alkylammonium salts

The thermogravimetric curves of di-n-propylammonium, di-iso-propylammonium, di-n-butylammonium and di-iso-butylammonium chlorides showed similar profiles, characterized by mass loss in only one stage, corresponding to decomposition of compounds. The following thermal stability order was obtained: [Bu₂ ⁿNH₂]Cl>[Pr₂ ⁿNH₂]Cl>[Pr₂ ⁱNH₂]Cl>[Bu₂ ⁱNH₂]Cl. The values of activation energy for non-isothermal data obtained by Ozawa and Coats-Redfern integral methods were in agreement and stability order obtained by thermogravimetry were reproduced in both methods. The decomposition reactions of [Pr₂ ⁿNH₂]Cl, [Pr₂ ⁱNH₂]Cl and [Bu₂ ⁱNH₂]Cl were better described by A3 model and [Bu₂ ⁿNH₂]Cl by A2 model. This revised version was published online in August 2006 with corrections to the Cover Date.     

Kinetics of thermal decomposition of dinitramide

Kinetic regularities of thermal decomposition of dinitramide in aqueous and sulfuric acid solutions were studied in a wide temperature range. The rate of the thermal decomposition of dinitramide was established to be determined by the rates of decomposition of different forms of dinitramide as the acidity of the medium increases: first, N(NO₂)⁻ anions, then HN(NO₂)₂ molecules, and finally, protonated H₂N(NO₂)₂ ⁺ cations. The temperature dependences of the rate constants of the decomposition of N(NO₂)⁻ (k _an) and HN(NO₂)₂ (k′_ac) and the equilibrium constant of dissociation of HN(NO₂)₂ (K _a) were determined:k _an=1.7·10¹⁷ exp(−20.5·10³/T), s⁻¹,k′_ac=7.9·10¹⁶ exp(−16.1·10³/T), s⁻¹, andK _a=1.4·10 exp(−2.6·10³/T). The temperature dependences of the decomposition rate constant of H₂N(NO₂)₂ ⁺ (k _d) and the equilibrium constant of the dissociation of H₂N(NO₂)₂ ⁺ (K _d) were estimated:k _d=10¹² exp(−7.9·10³/T), s⁻¹ andK _d=1.1 exp(6.4·10³/T). The kinetic and thermodynamic constants obtained make it possible to calculate the decomposition rate of dinitramide solutions in a wide range of temperatures and acidities of the medium. In this series of articles, we report the results of studies of the thermal decomposition of dinitramide performed in 1974–1978 and not published previously. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp. 2129–2133, December, 1997.     

硫酸铵的热分解

目前 ,关于各种无机酸铵盐的热分解情况都研究得比较清楚 ,但关于硫酸铵热分解情况的报道结果则不一致[1 - 7] 。本文对硫酸铵在各种温度下的常量热分解进行了研究 ,探讨其热分解机理 ,以利于对磷石膏 (主要成分为ＣａＳＯ4)的开发利用提供新的思路和方法[8] 。1　实验坩锅炉中热分解　约 1 0ｇ(ＮＨ4) 2 ＳＯ4置于恒重坩埚中 ,再放入坩埚炉中升温至设定温度 ,恒温0 5ｈ ,取出冷却 ,称重。并将坩埚中残余物用水溶解 ,测定水溶液中的Ｈ+、ＮＨ+4、ＳＯ2 -4 等离子的含量。其中ＮＨ+4含量采用甲醛法测定 ,ＳＯ2 -4 含量采用硫酸钡重量法测定…     

Formation process of indium oxide transparent conducting films via thermal decomposition

Indium 2-ethylhexanoate monohydroxide, In(OH)(O₂CCH(CH₂CH₃)(CH₂)₃CH₃)₂, is a precursory material to fabricate In₂O₃-based transparent conducting films by dip-coating process. Formation process of indium oxide transparent conducting films was investigated using an ultra-low acceleration voltage FE-SEM. The nanostructure change of the precursory layer was observed during the electron beam irradiation in vacuum. A flat and homogeneous surface of the as-coated layer changed to porous and net-work like nanostructure after 80 s; the pore diameter increased and the pore distance decreased although the number of pores remained unchanged. These processes were interpreted as the preliminary step to form porous films composed of nm-sized inter-linked oxide particles as reported in the previous papers by the authors.     

Mechanism of thermal decomposition of thiourea derivatives

The thermal decomposition of a series of compounds has been studied by thermogravimetry, mass spectrometry, nuclear magnetic resonance and elemental analysis. The combined use of mass spectrometry and thermogravimetry (MS and TG) in the analysis of these compounds has allowed characterization of the fragmentation pattern which was the objective of this research. The gaseous products, volatile condensed products and solid residues were identified by NMR and MS. Based on the product of thermal decomposition, the mechanism of thermal decomposition has been derived.     

过氧化苯甲酸叔丁酯的热分解动力学研究及SADT推算

研究了过氧化苯甲酸叔丁酯的热分解动力学及不同包装规格下的自加速分解温度(SADT),利用C600微量热仪测试了过氧化苯甲酸叔丁酯的热分解特征,得到升温速率分别为0.1 K/min、0.2 K/min、0.5 K/min、1 K/min下热流随时间的变化曲线,并使用Friedman等转化率法对所得的实验数据进行分析处理,得到了过氧化苯甲酸叔丁酯的分解反应活化能、指前因子等热动力学参数,推算了不同包装规格的过氧化苯甲酸叔丁酯的SADT。结果表明TBPB分解活化能及指前因子随转化率变化而变化,活化能范围为42-135.5 kJ/mol,指前因子范围为0.25-33.5,在25L聚乙烯桶包装下的SADT为59℃,50L下为52℃,200L下为46℃。     

Influence of sample preparation on thermal decomposition of wasted polyolefins-oil mixtures

Significant influence of sample preparation on thermal decomposition of polyolefin-technological oil mixtures was proved during tests. Samples of polymer-oil mixtures were prepared with two methods: reducing size and components mixing and soaking in temperature 170°C. Soaking causes decreasing thermal stability of the charge. This fact manifests itself in decreasing of thermal decomposition temperature in laboratory scale, as well as in change of characteristic decomposition temperatures during thermogravimetric analyses. Data analysis was performed with the use of classic method based on Arrhenius kinetic equation and three-parameter model. The influence of sample composition and preparation method on values of three-parameter equation coefficients was observed.     

General remarks on the thermal decomposition of some drugs

The thermal decomposition of antituberculous, local anaesthetic and calcium salts of organic acids used as the drugs has been studied by differential thermal and thermogravimetric techniques. General characteristics of their thermal decomposition has been made. The effect of sample size over the range 20–200 mg and heating rate over the range 3–15 deg·min^?1 on the thermal degradation has been investigated. The values of the kinetic parameters has been also determined.