Superior high-rate cycling performance of LiFePO4/C-PPy composite at 55 °C

A facile chemical polymerization method was applied to prepare LiFePO₄/C-PPy composite using Fe(III)tosylate as oxidant. The as-prepared LiFePO₄/C-PPy sample with PPy content of approximately 4 wt% showed great rate capability with a discharge capacity of 115 mAh/g at 20C. High temperate cycling performance of the LiFePO₄/C-PPy sample was compared with bare LiFePO₄/C at 5C charge–discharge rate at 55 °C. The LiFePO₄/C-PPy cathode showed superior cycling stability with an initial capacity of 155 mAh/g. Ninety percentage of this initial capacity was retained after 300 cycles, compared to 40% of that of bare LiFePO₄/C. The LiFePO₄/C-PPy electrode showed stable discharge plateau voltage of 3.35–3.25 V vs. Li⁺/Li during long term cycling. The superior performance of the LiFePO₄/C-PPy electrode was due to the enhanced electrical conductivity, negligible iron dissolution and alleviated electrode cracking contributed by PPy coating.     

Fibriform polyaniline/nano-TiO2 composite as an electrode material for aqueous redox supercapacitors

Fibriform polyaniline/nano-TiO₂ composite is prepared by one-step in situ oxidation polymerization of aniline in the presence of nano-TiO₂ particles, which contains 80% conducting polyaniline by mass, with a conductivity of 2.45 S/cm at 25 °C. Its maximum specific capacitance is 330 F g^?1 at a constant current density of 1.5 A g^?1, and can be subjected to charge/discharge over 10,000 cycles in the voltage range of 0.05–0.55 V.     

Synthesis of nickel selenide thin films for high performance all-solid-state asymmetric supercapacitors

As a significant semiconductor, nickel selenide shows enormous potential and extensive application prospects in the field of sensor, photocatalysis and supercapacitor. In this paper, nickel selenide (Ni₃Se₂, NiSe) thin films were successfully fabricated on stainless-steel sheet using a facile, effective electrodeposition technique. The morphologies, microstructures and chemical compositions of the thin films are characterized systematically. Electrochemical tests exhibit that the Ni₃Se₂ and NiSe possess high specific capacitance of 581.1 F/g and 1644.7 F/g, respectively. A flexible, all-solid-state asymmetric supercapacitor is assembled by utilizing NiSe film as positive electrode and activated carbon as negative electrode. The solid device delivers a high areal capacitance of 27.0 mF/cm² at the current density of 0.7 mA/cm². The maximum volumetric energy density and power density of the NiSe//AC asymmetric SCs can achieve 0.26 mWh/cm³ and 33.35 mW/cm³, respectively. The device shows robust cycling stability with 84.6% capacitance retention after 10,000 cycles, outstanding flexibility and satisfactory mechanical stability. Moreover, two devices in series can light up a red light-emitting diode, which displayed great potential applications for energy storage.     

Studies of thermal decay of electropolymerized polypyrrole using in situ surface-enhanced Raman spectroscopy

In this work, the thermal degradation of polypyrrole (PPy) films was investigated by using in situ surface-enhanced Raman spectroscopy (SERS) for the first time. The results indicate that the decay of PPy in conductivity can be ascribed to the loss in oxidation degree and to the shorter conjugation length of PPy upon heating samples from 25 to 75 °C. Continuously raising the temperature of the sample from 75 to 125 °C results in serious decay. The oxidation degree of PPy is significantly decreased correspondingly. However, the peak assigned to the CC backbone stretching becomes broader due to the thermal decomposition of PPy. At temperatures of samples higher than 125 °C, PPy films lose their conducting properties and no characteristic peaks of oxidized PPy related to the oxidation degrees can be observed. Moreover, the peak of the CC backbone stretching completely disappear due to the complete decomposition of PPy.     

High power LiCoO2 cathode materials with ultra energy density for Li-ion cells

Hydrothermally prepared 100 nm-sized LiCoO₂ with a plate morphology packed in a crucible resulted in 40 μm-sized particles that consisted of aggregated < 1 micron-sized particles after annealing at 900 °C for 3 h. In the condition where the optimized electrode pore volume was 20%, 4.1 g/cc of electrode density was obtained, which corresponded to 3 Wh/cc, which is the highest value among the cathode materials. Furthermore, the LiCoO₂ showed excellent capacity retention of 78% after 290 cycles in a Li-ion cell under 7 C rate cycling.     

Nano-LiCoO2 as cathode material of large capacity and high rate capability for aqueous rechargeable lithium batteries

Crystalline nanoparticles of LiCoO₂ are prepared by a sol–gel method at 550 °C and characterized by X-ray diffraction. Their electrochemical behaviors were characterized by cyclic voltammograms, capacity measurement and cycling performance. Results show that the reversible capacity of the nano-LiCoO₂ can be up to 143 mAh/g at 1000 mA/g and still be 133 mAh/g at 10,000 mA/g (about 70C) in 0.5 mol/l Li₂SO₄ aqueous electrolyte. In addition, their cycling behavior is also very satisfactory, no evident capacity fading during the initial 40 cycles. These data present great promise for the application of aqueous rechargeable lithium batteries.     

Pulse polymerized polypyrrole electrodes for high energy density electrochemical supercapacitor

A novel method of pulsed polymerization for pyrrole exhibiting highest capacitance and very high energy density polypyrrole supercapacitor is reported. Stable polypyrrole films with good electrochemical reversibility and high doping degree were obtained by applying ultra short on time current pulse for polymerization. Pulse on time plays an important role in controlling chain size and chain defects whereas pulse off time contributes in polymer conjugation and orientation. A regime of pulse on time is identified to yield highly capacitive and stable films for supercapacitor application. Very high specific capacitance of 400 F/g and an unexpectedly high energy density of 250 Wh/kg were obtained form pulsed polymerized ordered polypyrrole structures in acidic electrolyte. Stability tests performed on pulsed polymerized pPy electrode yield long cycling life up to 10,000 cycles at charge/discharge current density of 5 mA/cm².     

Titanium vanadium nitride electrode for micro-supercapacitors

Here we report on the synthesis of binary transition metal nitride electrodes based on titanium vanadium nitride (TiVN) thin films. These films were deposited by a method compatible with micro-electronic processes which consists of DC co-sputtering of vanadium (V) and titanium (Ti) targets. TiVN films with different Ti/V ratio were deposited. A dependence of the capacitance and the cycling stability with the Ti/V atomic ratio in the films was established. While V rich sample exhibits a Faradic behavior that limits its cycling ability despite a high areal and volumetric capacity, the addition of Ti in the film drastically improves the cycling ability with virtually no fade in capacitance after 10,000 cycles. Furthermore, a 1.1 Ti/V ratio leads to an areal capacitance up to 15 mF·cm^− 2 in 1 M KOH electrolyte solution. Such electrodes shed light on the use of binary transition metal nitrides as candidate electrodes for micro-supercapacitor.     

Electrodeposited PbO2 thin film on Ti electrode for application in hybrid supercapacitor

PbO₂ thin films were prepared by pulse current technique on Ti substrate from Pb(NO₃)₂ plating solution. The hybrid supercapacitor was designed with PbO₂ thin film as positive electrode and activated carbon (AC) as negative electrode in the 5.3 M H₂SO₄ solution. Its electrochemical properties were determined by cyclic voltammetry (CV), charge–discharge test and electrochemical impedance spectroscopy (EIS). The results revealed that the PbO₂/AC hybrid supercapacitor exhibited large specific capacitance, high-power and stable cycle performance. In the potential range of 0.8–1.8 V, the hybrid supercapacitor can deliver a specific capacitance of 71.5 F g^?1 at a discharge current density of 200 mA g^?1(4 mA cm^?2) when the mass ratio of AC to PbO₂ was three, and after 4500 deep cycles, the specific capacitance remains at 64.4 F g^?1, or 32.2 Wh Kg^?1 in specific energy, and the capacity only fades 10% from its initial value.     

Paper-like free-standing polypyrrole and polypyrrole–LiFePO4 composite films for flexible and bendable rechargeable battery

Highly flexible, paper-like, free-standing polypyrrole and polypyrrole–LiFePO₄ composite films were prepared using the electropolymerization method. The films are soft, lightweight, mechanically robust and highly electrically conductivity. The electrochemical behavior of the free-standing films was examined against lithium counter electrode. The electrochemical performance of the free-standing pure PPy electrode was improved by incorporating the most promising cathode material, LiFePO₄, into the PPy films. The cell with PPy–LiFePO₄ composite film had a higher discharge capacity beyond 50 cycles (80 mA h/g) than that of the cell with pure PPy (60 mA h/g). The free-standing films can be used as electrode materials to satisfy the new market demand for flexible and bendable batteries that are suitable for the various types of design and power needs of soft portable electronic equipment.     

A study of ion charge transfer on electrochemical behaviors of poly(vinylidene fluoride)-derived carbon electrodes

In this work, porous carbon with a high specific surface area as electrode materials for supercapacitors are obtained by a carbonization process at various temperatures from 700 °C to 1000 °C without activation process using poly(vinylidene fluoride) (PVDF) as a carbon precursor. The electrochemical performance is characterized by cyclic voltammetry and galvanostatic charge–discharge cycling performance using two-electrode system in 6.0 M KOH as an aqueous electrolyte. The results indicate that carbonization temperature significantly affected the specific surface area and pore volume of the PVDF-derived carbons and their capacitive behavior. In particular, the electrochemical performance of the prepared PVDF-derived carbon is determined by both the electric double-layer capacitance and the pseudo-capacitance resulting from the residual surface functional groups on PVDF-derived carbons.     

Characterization of the different fractions obtained from the pyrolysis of rope industry waste

A study of the possibilities of pyrolysis for recovering wastes of the rope's industry has been carried out. The pyrolysis of this lignocellulosic residue started at 250 °C, with the main region of decomposition occurring at temperatures between 300 and 350 °C. As the reaction temperature increased, the yields of pyrolyzed gas and oil increased, yielding 22 wt.% of a carbonaceous residue, 50 wt.% tars and a gas fraction at 800 °C. The chemical composition and textural characterization of the chars obtained at various temperatures confirmed that even if most decomposition occurs at 400 °C, there are some pyrolytic reactions still going on above 550 °C. The different pyrolysis fractions were analyzed by GC–MS; the produced oil was rich in hydrocarbons and alcohols. On the other hand, the gas fraction is mainly composed of CO₂, CO and CH₄. Finally, the carbonaceous solid residue (char) displayed porous features, with a more developed porous structure as the pyrolysis temperature increased.     

Poly(vinyl alcohol) separators improve the coulombic efficiency of activated carbon cathodes in microbial fuel cells

High-performance microbial fuel cell (MFC) air cathodes were constructed using a combination of inexpensive materials for the oxygen reduction cathode catalyst and the electrode separator. A poly(vinyl alcohol) (PVA)-based electrode separator enabled high coulombic efficiencies (CEs) in MFCs with activated carbon (AC) cathodes without significantly decreasing power output. MFCs with AC cathodes and PVA separators had CEs (43%–89%) about twice those of AC cathodes lacking a separator (17%–55%) or cathodes made with platinum supported on carbon catalyst (Pt/C) and carbon cloth (CE of 20%–50%). Similar maximum power densities were observed for AC-cathode MFCs with (840 ± 42 mW/m²) or without (860 ± 10 mW/m²) the PVA separator after 18 cycles (36 days). Compared to MFCs with Pt-based cathodes, the cost of the AC-based cathodes with PVA separators was substantially reduced. These results demonstrated that AC-based cathodes with PVA separators are an inexpensive alternative to expensive Pt-based cathodes for construction of larger-scale MFC reactors.     

Transition metal-nitrogen-carbon catalysts for oxygen reduction reaction in neutral electrolyte

Platinum group metal-free (PGM-free) catalysts based on M-N-C types of materials with M as Mn, Fe, Co and Ni and aminoantipyrine (AAPyr) as N-C precursors were synthesized using sacrificial support method. Catalysts kinetics of oxygen reduction reaction (ORR) was studied using rotating ring disk electrode (RRDE) in neutral pH. Results showed that performances were distributed among the catalysts as: Fe-AAPyr > Co-AAPyr > Mn-AAPyr > Ni-AAPyr. Fe-AAPyr had the highest onset potential and half-wave potential. All the materials showed similar limiting current. Fe-AAPyr had an electron transfer involving 4e⁻ with peroxide formed lower than 5%. Considering H₂O₂ produced, it seems that Co-AAPyr, Mn-AAPyr and Ni-AAPyr follow a 2 × 2e⁻ mechanism with peroxide formed during the intermediate step. Durability test was done on Fe-AAPyr for 10,000 cycles. Decrease of activity was observed only after 10,000 cycles.     

The effect of copper content on the reactivity of Cu/Co6Al2 solids in the catalytic steam reforming of methane reaction

The steam reforming of methane over Cu/Co₆Al₂ mixed oxides with different copper contents was studied. The Co₆Al₂ support was prepared via the hydrotalcite route. It was thermally stabilized at 500 °C, impregnated with 5 wt.%, 15 wt.% or 25 wt.% copper using copper (II) nitrate Cu(NO₃)₂·3H₂O precursor and then calcined again at 500 °C under an air flow. The impregnation of copper enhanced significantly the reactivity of the solids in the considered reaction. The 5Cu/Co₆Al₂ solid was the most reactive one, with a methane conversion of 96% at 650 °C. The selectivities of H₂ and CO₂ were also better for the catalyst containing 5 wt.% copper compared to higher copper loadings. The decrease in the catalytic reactivity with increasing the copper content was attributed to the formation of agglomerated and less reactive CuO species, which were detected by XRD and TPR analyses.     

Spherical Sn–Ni–C alloy anode material with submicro/micro complex particle structure for lithium secondary batteries

Submicro/micro-scaled spherical Sn–Ni–C alloy powders synthesized from oxides of Sn and Ni via carbothermal reduction at 900 °C were examined for use as anode materials in Li-ion battery. The synthesized spherical Sn–Ni–C particles show a loose micro-sized structure and a multi-phase composition. The reaction product carbon oxide gases yielded in the carbothermal reduction process should be responsible to the loose structure characteristics of Sn–Ni–C particles. The prepared Sn–Ni–C alloy composite electrode exhibits a stable reversible capacity of 310 mA h g⁻¹ at constant current density of 100 mA g⁻¹, and can be retained at 290 mA h g⁻¹ after 25 cycles. The space existing in loose particle can accommodate the large volume changes during charge/discharge cycling. The ductile component Ni plays as a buffer to relieve the mechanical stress induced by the large volume changes upon cycling. The remained carbon can prevent the aggregation between small alloy particles. All these factors contribute greatly to the excellent cycling stability of Sn–Ni–C alloy electrode. This carbothermal reduction method is simple, cheap and mass-productive, thus suitable to large scale production of alloy anode powders used for lithium ion batteries.     

Facile synthesis of high electrical conductive CoP via solid-state synthetic routes for supercapacitors

Co-P precursor was prepared by a mechanical alloying method and then is controlled to synthesis of Co P phase through an annealing method. The optimal conditions of ball milling and annealing temperature are investigated. The Co P exhibits higher electrical conductivity than graphite and cobalt oxide, showing excellent pseudocapacitive properties due its high electrical conductivity which can result in a fast electron transfer in high rate charge–discharge possess. The as-obtained Co P electrode achieves a high specific capacitance of 447.5 F/g at 1 A/g, and displays an excellent rate capability as well as good cycling stability. Besides, the asymmetric supercapacitor(ASC) based on the Co P as the positive electrode and activated carbon(AC) as the negative electrode was assembled and displayed a high rate capability(60%of the capacitance is retained when the current density increased from 1 A/g to 12 A/g), excellent cycling stability(96.7% of the initial capacitance is retained after 5000 cycles), and a superior specific energy of19 Wh/kg at a power density of 350.8 W/kg. The results suggest that the Co P electrode materials have a great potential for developing high-performance electrochemical energy storage devices.     

Asymmetric electrochemical capacitor microdevice designed with vanadium nitride and nickel oxide thin film electrodes

Vanadium nitride thin film has been coupled with electrodeposited nickel oxide in order to design an electrochemical capacitor microdevice. VN has been used as negative electrode while NiO was used as the positive one in 1 M KOH electrolyte. VN exhibits a pseudo-capacitive behavior while NiO shows a faradaic behavior. This asymmetric microdevice has been operated between 0.5 and up to 1.8 V in aqueous based electrolyte (1 M KOH). Long term cycling ability (10,000 charge/discharge cycles) has been demonstrated with interesting energy (1.0 μW h cm^− 2) and power (40 mW cm^− 2) densities.     

Drastically enhanced cycle life of Co-B alloy electrode by 8-hydroxyquinoline at elevated temperature

The effect 8-hydroxyquinoline (8-HQ) additive in electrolyte on the cyclic stability of Co-B alloy electrode was investigated at elevated temperature (55 °C). Charge–discharge measurements show that 8-HQ can drastically enhance the cycle life of Co-B alloy electrode. Specifically, in the electrolyte containing 0.028 M 8-HQ additive, the discharge capacity of Co-B alloy electrode after 100 cycles are still up to 385.8 mAh/g at 55 °C. However, for the electrode in 8-HQ-free electrolyte, its discharge capacity is sharply decreased to only 138.5 mAh/g after 100 cycles. ICP-OES, XRD and ATR/FT-IR measurements were used to clarify the reason of the improvement in the cyclic stability. These results show that beneficial effect of 8-HQ on cycle life of Co-B alloy electrode can be attributed to the formation of insoluble complex (8-HQ)₂Co(II)·2H₂O protective layer that can suppress the dissolution of Co(OH)₂ into electrolyte at elevated temperature.     

Tube-covering-tube nanostructured polyaniline/carbon nanotube array composite electrode with high capacitance and superior rate performance as well as good cycling stability

The combination of a vertically aligned carbon nanotube array (CNTA) framework and electrodeposition technique leads to a tube-covering-tube nanostructured polyaniline (PANI)/CNTA composite electrode with hierarchical porous structure, large surface area, and superior conductivity. PANI/CNTA composite electrode has high specific capacitance (1030 F g⁻¹), superior rate capability (95% capacity retention at 118 A g⁻¹), and high stability (5.5% capacity loss after 5000 cycles). Energy storage characteristics of the PANI/CNTA composite are presented in this paper.