Electrical conductivity of fully densified nano CaZr0.90In0.10O3 − δ ceramics prepared by a water-based gel precipitation method

Water-based gel precipitation method was first applied to synthesize high purity nano CaZr_0.90In_0.10O_3 ? δ powders suitable for fabricating dense ceramics at lower temperature. By using CaCO₃, Zr(NO₃)₄ and In(NO₃)₃ as raw materials, PEG as dispersant, CaZr_0.90In_0.10O_3 ? δ with an average particle size of about 40 nm was obtained at 850 °C, which was nearly 350 °C lower than that of traditional solid-state reaction method. Fully densified ceramics with an average grain size of 200–300 nm were obtained at 1350 °C, a temperature about 250 °C lower than that of traditional sintering techniques. Experimental results showed that the flexure stress, total, bulk and grain boundary protonic conductivities of the ceramics were more favorable than those of the ceramics fabricated at 1500 °C and 1600 °C from the powders synthesized by solid-state reaction method.     

Photocatalytic property of colloidal TiO2 nanoparticles prepared by sparking process

Titanium oxide nanoparticles (NPs) were successfully prepared by sparking off two titanium tips into water for 1–5 h. The nanoparticle-dispersed water was obtained for further characterization. The transmission electron microscopy result shows that the particle size is in the range of 1–5 nm. The electron diffraction patterns and Raman spectra reveal that the as-prepared and the annealed samples at 250 °C are the anatase phase. However, the anatase–rutile phase transformation was observed from the samples at annealing temperature as low as 500 °C. The result of methylene blue-decoloration testing under sunbath suggests that the NPs have good photocatalytic property.     

Characterization of Laves phase in Crofer 22 H stainless steel

This study investigated the effect of annealing temperature on the precipitation behavior of Crofer^® 22 H at 600 °C, 700 °C, and 800 °C. The grain size distribution, precipitate phase identification, and microstructure were analyzed using electron backscatter diffraction (EBSD) and energy dispersive X-ray spectroscopy (EDS). The morphology of Laves phase (Fe,Cr,Si)₂(Nb,W) precipitates having the Cr₂Nb structure changed from strip-like to needle-shaped as the annealing temperature was increased. The precipitates of the Laves phase also shifted from the grain boundaries to the grain interiors when the temperature was increased. However, the average grain size (150 μm) of the ferritic matrix did not significantly change at 600 °C, 700 °C, and 800 °C for 10 h.     

Effect of processing conditions on sonochemical synthesis of nanosized copper aluminate powders

Nanosized copper aluminate (CuAl₂O₄) spinel particles have been prepared by a precursor approach with the aid of ultrasound radiation. Mono-phasic copper aluminate with a crystallite diameter of 17 nm along the (3 1 1) plane was formed when the products were synthesized using Cu(NO₃)₂·6H₂O and Al(NO₃)₃·9H₂O as starting materials, with urea as a precipitation agent at a concentration of 9 M. The reaction was carried out under ultrasound irradiation at 80 °C for 4 h and a calcination temperature of 900 °C for 6 h. The synthesized copper aluminate particles and the effect of different processing conditions such as the copper source, precipitation agents, sonochemical reaction time, calcination temperature and time were analyzed and characterized by the techniques of powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM) and Fourier transformation infrared spectroscopy (FT–IR).     

Effect of calcination temperature on phase transformation,structural and optical properties of sol–gel derived ZrO2 nanostructures

Zirconia (ZrO₂) nanostructures of various sizes have been synthesized using sol–gel method followed by calcination of the samples from 500 to 700 °C. The calcined ZrO₂ powder samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infra-red spectroscopy (FT-IR), UV–visible spectroscopy (UV–vis.), Raman spectroscopy (RS) and thermogravimetric analysis (TGA). The phase transformation from tetragonal (t) to monoclinic (m) was observed. The average diameter of the ZrO₂ nanostructures calcined at 500, 600 and 700 °C was calculated to be 8, 17 and 10 nm, respectively. The ZrO₂ sample calcined at 500 °C with tetragonal phase shows a direct optical band gap of 5.1 eV. The value of optical band gap is decreased to 4.3 eV for the ZrO₂ calcined at 600 °C, which contains both tetragonal (73%) and monoclinic (27%) phases. On further calcination at 700 °C, where the ZrO₂ nanostructures have 36% tetragonal and 64% monoclinic phases, the optical band gap is calculated to be 4.8 eV. The enhancement in optical band gap for ZrO₂ calcined at 700 °C may be due to the rod like shape of ZrO₂ nanostructures. The tetragonal to monoclinic phase transformation was also confirmed by analyzing Raman spectroscopic data. The TG analysis revealed that the ZrO₂ nanostructure with dominance of monoclinic phase is found to be more stable over the tetragonal phase. In order to confirm the phase stability of the two phases of ZrO₂, single point energy is calculated corresponding to its monoclinic and tetragonal structures using density functional theory (DFT) calculations. The results obtained by theoretical calculations are in good agreement with the experimental findings.     

Coarsening phenomena of metal nanoparticles and the influence of the support pre-treatment: Pt/TiO2(110)

One of the technologically most important requirements for the application of oxide-supported metal nanoparticles (NPs) in the fields of molecular electronics, plasmonics, and catalysis is the achievement of thermally stable systems. For this purpose, a thorough understanding of the different pathways underlying thermally-driven coarsening phenomena, and the effect of the nanoparticle synthesis method, support morphology, and degree of support reduction on NP sintering is needed. In this study, the sintering of supported metal NPs has been monitored via scanning tunneling microscopy combined with simulations following the Ostwald ripening and diffusion-coalescence models. Modifications were introduced to the diffusion-coalescence model to incorporate the correct temperature dependence and energetics. Such methods were applied to describe coarsening phenomena of physical-vapor deposited (PVD) and micellar Pt NPs supported on TiO₂(110). The TiO₂(110) substrates were exposed to different pre-treatments, leading to reduced, oxidized and polymer-modified TiO₂ surfaces. Such pre-treatments were found to affect the coarsening behavior of the NPs.No coarsening was observed for the micellar Pt NPs, maintaining their as-prepared size of ~ 3 nm after annealing in UHV at 1060 °C. Regardless of the initial substrate pre-treatment, the average size of the PVD-grown NPs was found to increase after identical thermal cycles, namely, from 0.5 ± 0.2 nm to 1.0 ± 0.3 nm for pristine TiO₂, and from 0.8 ± 0.3 nm to 1.3 ± 0.6 nm for polymer-coated TiO₂ after identical thermal treatments. Although no direct real-time in situ microscopic evidence is available to determine the dominant coarsening mechanism of the PVD NPs unequivocally, our simulations following the diffusion-coalescence coarsening route were in significantly better agreement with the experimental data as compared to those based on the Ostwald-ripening model. The enhanced thermal stability of the micellar NPs as compared to the PVD clusters might be related to their initial larger NP size, narrower size distribution, and larger interparticle distances.     

Polymorphic phase transition and thermal stability in squaric acid (H2C4O4)

Phase transformations in squaric acid (H₂C₄O₄) have been investigated by thermogravimetry and differential scanning calorimetry with different heating rates β. The mass loss in TG apparently begins at onset temperatures T_di=245±5 °C (β=5 °C min^?1), 262±5 °C (β=10 °C min^?1), and 275±5 °C (β=20 °C min^?1). A polymorphic phase transition was recognized as a weak endothermic peak in DSC around 101 °C (T_c⁺). Further heating with β=10 °C min^?1 in DSC revealed deviation of the baseline around 310 °C (T_i), and a large unusual exothermic peak around 355 °C (T_p), which are interpreted as an onset and a peak temperature of thermal decomposition, respectively. The activation energy of the thermal decomposition was obtained by employing relevant models. Thermal decomposition was recognized as a carbonization process, resulting in amorphous carbon.     

Ultrasound assisted co-precipitation of nanostructured CuO–ZnO–Al2O3 over HZSM-5: Effect of precursor and irradiation power on nanocatalyst properties and catalytic performance for direct syngas to DME

Nanostructured CuO–ZnO–Al₂O₃/HZSM-5 was synthesized from nitrate and acetate precursors using ultrasound assisted co-precipitation method under different irradiation powers. The CuO–ZnO–Al₂O₃/HZSM-5 nanocatalysts were characterized using XRD, FESEM, BET, FTIR and EDX Dot-mapping analyses. The results indicated precursor type and irradiation power have significant influences on phase structure, morphology, surface area and functional groups. It was observed that the acetate formulated CuO–ZnO–Al₂O₃/HZSM-5 nanocatalyst have smaller CuO crystals with better dispersion and stronger interaction between components in comparison to nitrate based nanocatalysts. Ultrasound assisted co-precipitation synthesis method resulted in nanocatalyst with more uniform morphology compared to conventional method and increasing irradiation power yields smaller particles with better dispersion and higher surface area. Additionally the crystallinity of CuO is lower at high irradiation powers leading to stronger interaction between metal oxides. The nanocatalysts performance were tested at 200–300 °C, 10–40 bar and space velocity of 18,000–36,000 cm³/g h with the inlet gas composition of H₂/CO = 2/1 in a stainless steel autoclave reactor. The acetate based nanocatalysts irradiated with higher levels of power exhibited better reactivity in terms of CO conversion and DME yield. While there is an optimal temperature for CO conversion and DME yield in direct synthesis of DME, CO conversion and DME yield both increase with the pressure increase. Furthermore ultrasound assisted co-precipitation method yields more stable CuO–ZnO–Al₂O₃/HZSM-5 nanocatalyst while conventional precipitated nanocatalyst lost their activity ca. 18% and 58% in terms of CO conversion and DME yield respectively in 24 h time on stream test.     

A preliminary study on a new LiBOB/acetamide solid phase transition electrolyte

New solid electrolytes containing acetamide and lithium bioxalato borate (LiBOB) with different molar ratios have been investigated. Their melting points (T_m) are around 42 °C. The ionic conductivities and activation energies vary drastically below and above T_m, indicating a typical feature of phase transition electrolyte. The ionic conductivity of the LiBOB/acetamide electrolyte with a molar ratio of 1:8 is 5 × 10^? 8 S cm^? 1 at 25 °C but increases to 4 × 10^? 3 S cm^? 1 at 60 °C. It was found that anode materials, such as graphite and Li₄Ti₅O₁₂, could not discharge and charge properly in this electrolyte at 60 °C due to the difficulty in forming a stable passivating layer on the anodes. However, a Li/LiFePO₄ cell with this electrolyte can be charged properly after heating to 60 °C, but cannot be charged at room temperature. Although the LiBOB/acetamide electrolytes are not suitable for Li-ion batteries due to poor electrode compatibility, the current results indicate that a solid electrolyte with a slightly higher phase transition temperature than room temperature may find potential application in stationary battery for energy storage where the electrolyte is at high conductive liquid state at elevated temperature and low conductive solid state at low temperature. The interaction between acetamide and LiBOB in the electrolyte is also studied by Raman and FTIR spectroscopy.     

Kinetic study of isothermal crystallization process of Gd2Ti2O7 precursor's powder prepared through the Pechini synthetic approach

Crystallization process of Gd₂Ti₂O₇ precursor's powder prepared by Pechini-type polymerized complex route has been studied under isothermal experimental conditions in an air atmosphere. It was found that the crystallization proceeds through two-parameter Šesták–Berggren (SB) autocatalytic model, in the operating temperature range of 550 °C≤T≤750 °C. Based on the behavior of SB parameters (M, N), it was found that in the lower operating temperature range, the crystallites with relatively low compactness exist, which probably disclosed low dimensionality of crystal growth from numerous nucleation sites, where the amorphous solid is produced. In the higher operating temperature region (above 750 °C), it was established that a morphological well-defined and high-dimensional particles of the formed pyrochlore phase can be expected. It was found that at T=850 °C, there is a change in the rate-determining reaction step, from autocatalytic into the contracting volume mechanism.     

Synthesis and investigations on the stability of La0.8Sr0.2CuO2.4+δ at high temperatures

For application in solid oxide fuel cells La_0.8Sr_0.2CuO_2.4+δ was synthesized and the phase evolution was characterized after quenching from different temperatures and after slow cooling. A single phase perovskite was found after quenching from 950 °C. The electrical conductivity of the La_0.8Sr_0.2CuO_2.4+δ perovskite exhibited metallic behavior reaching values of about 270 S/cm at 800 °C in air. The thermal expansion between 30 and 800 °C gave a thermal expansion coefficient of 11.1 × 10^− 6 K^− 1.At higher temperatures, the perovskite was transformed to the K₂NiF₄-type structure via an intermediate stage that can be best described as a LaSrCuO₄ phase with preferential growing of {020} lattice planes. After sintering at 1100 °C and slow cooling in the furnace a phase mixture of (La,Sr)CuO_4+δ and (La,Sr)CuO_2.4+δ perovskite was obtained. This phase mixture showed higher electrical conductivity (400 S/cm at 800 °C) and smaller thermal expansion coefficient (9.6 × 10^− 6 K^− 1) than the single phase La_0.8Sr_0.2CuO_2.4+δ perovskite.     

Preparation of cadmium stannate films by spray pyrolysis technique

Cadmium stannate thin films were prepared by spray pyrolysis technique using cadmium acetate and tin(II) chloride precursors at substrate temperatures 450 °C and 500 °C. XRD pattern confirms the formation of orthorhombic (1 1 1) cadmium stannate phase for the film prepared at substrate temperature of 500 °C, whereas, films prepared at 450 °C are amorphous. Film formation does not occur at substrate temperature from 300 to 375 °C. SEM images reveal that the surface of the prepared Cd₂SnO₄ film is smooth. The average optical transmittance of ∼86% is obtained for the film prepared at substrate temperature of 500 °C with the film thickness of 400 nm. The optical band gap value of the films varies from 2.7 to 2.94 eV. The film prepared at 500 °C shows a minimum resistivity of 35.6 × 10⁻⁴ Ω cm.     

Preparation of phase pure and well-crystallized Li4Ti5O12 nanoparticles by precision control of starting mixture and calcining at lowest possible temperatures

In an attempt to obtain spinel Li₄Ti₅O₁₂ with smallest possible grain size and highest possible phase purity via a solid state route, we tried to elevate reactivity of the reactant mixture by mechanical activation and appropriate choice of the starting materials. From the stoichiometric mixture comprising Li₂CO₃ and 150 nm anatase, we needed to heat at 950 °C for 1 h to obtain 81–88% phase purity (PhP) of Li₄Ti₅O₁₂ with its average grain size ca 600 nm. After mechanical activation with a multi-ring mill for 30 min, 850 °C was enough to obtain 85–87% pure 500 nm spinel. From a combination of LiNO₃ and 50 nm anatase, 90–91% phase pure product with its grain size 240 nm was obtained at 750 °C due to fusion of the nitrate and shorter diffusion path. By using CH₃COOLi.2H₂O and 50 nm anatase we obtained 130 nm Li₄Ti₅O₁₂ with its PhP ca 90% by milling the mixture preliminarily calcined at 500 °C for 1 h and heating subsequently at 700 for 1 h.     

Effect of processing temperature on the superconducting properties of acetone doped MgB2 tapes

Correlation of phase formation, critical transition temperature T_c, microstructure, and critical current density J_c with sintering temperature has been studied for acetone doped MgB₂/Fe tapes. Sintering was performed at 600–850 °C for 1 h in a flowing Ar atmosphere. High boron substitution by carbon was obtained with increasing the sintering temperature; however, the acetone doped samples synthesized at 800 °C contain large size MgB₂ grains and more MgO impurities. Incomplete reaction for the acetone doped samples heated at 600 °C result in bad intergrain connectivity. At 4.2 K, the best J_c value was achieved in the acetone doped sample sintered at 700 °C, which reached 24,000 A/cm² at 10 T and 10,000 A/cm² at 12 T, respectively. Our results indicate that the small grain size and less impurity were also important for the improvement of J_c–B properties besides the substitutions of B by C.     

Degradation of 2,4-dinitrophenol using a combination of hydrodynamic cavitation,chemical and advanced oxidation processes

In the present work, degradation of 2,4-dinitrophenol (DNP), a persistent organic contaminant with high toxicity and very low biodegradability has been investigated using combination of hydrodynamic cavitation (HC) and chemical/advanced oxidation. The cavitating conditions have been generated using orifice plate as a cavitating device. Initially, the optimization of basic operating parameters have been done by performing experiments over varying inlet pressure (over the range of 3–6 bar), temperature (30 °C, 35 °C and 40 °C) and solution pH (over the range of 3–11). Subsequently, combined treatment strategies have been investigated for process intensification of the degradation process. The effect of HC combined with chemical oxidation processes such as hydrogen peroxide (HC/H₂O₂), ferrous activated persulfate (HC/Na₂S₂O₈/FeSO₄) and HC coupled with advanced oxidation processes such as conventional Fenton (HC/FeSO₄/H₂O₂), advanced Fenton (HC/Fe/H₂O₂) and Fenton-like process (HC/CuO/H₂O₂) on the extent of degradation of DNP have also been investigated at optimized conditions of pH 4, temperature of 35 °C and inlet pressure of 4 bar. Kinetic study revealed that degradation of DNP fitted first order kinetics for all the approaches under investigation. Complete degradation with maximum rate of DNP degradation has been observed for the combined HC/Fenton process. The energy consumption analysis for hydrodynamic cavitation based process has been done on the basis of cavitational yield. Degradation intermediates have also been identified and quantified in the current work. The synergistic index calculated for all the combined processes indicates HC/Fenton process is more feasible than the combination of HC with other Fenton like processes.     

Surface reactions of TiCl4 and Al(CH3)3 on GaAs(100) during the first half-cycle of atomic layer deposition

GaAs(100) was exposed to pulses of trimethylaluminum (TMA, Al(CH₃)₃) and titanium tetrachloride (TiCl₄) to mimic the first half-cycle of atomic layer deposition (ALD). Both precursors removed the 9.0 ± 1.6 Å-thick mixed oxide consisting primarily of As₂O₃ with a small Ga₂O component that was left on the surface after aqueous HF treatment and vacuum annealing. In its place, TMA deposited an Al₂O₃ layer, but TiCl₄ exposure left Cl atoms adsorbed to an elemental As layer. This suggests that oxygen was removed by the formation of a volatile oxychloride species. A small TiO₂ coverage of approximately 0.04 monolayer remained on the surface for deposition temperatures of 89 °C to 135 °C, but no TiO₂ was present from 170 °C to 230 °C. The adsorbed Cl layer chemically passivated the surface at these temperatures and blocked TiO₂ deposition even after 50 full ALD cycles of TiCl₄ and water vapor. The Cl and As layers desorbed simultaneously at higher temperature producing peaks in the temperature programmed desorption spectrum in the range 237–297 °C. This allowed TiO₂ deposition at 300 °C in single TiCl₄ pulse experiments. On the native oxide-covered surface where there was a higher proportional Ga oxide composition, TiCl₄ exposure deposited TiO₂.     

Spray pyrolyzed NiO–C nanocomposite as an anode material for the lithium-ion battery with enhanced capacity retention

NiO–C nanocomposite was prepared by a spray pyrolysis method using a mixture of Ni(NO₃)₂ and citric acid solution at 600 °C. The microstructure and morphology of the NiO–C composite were characterized by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS) mapping, and thermogravimetric analysis (TGA). The results showed that the NiO nanoparticles were surrounded by amorphous carbon. Electrochemical tests demonstrated that the NiO–C nanocomposites exhibited better capacity retention (382 mAh g^− 1 for 50 cycles) than that of pure NiO (141 mAh g^− 1 for 50 cycles), which was also prepared by spray pyrolysis using only Ni(NO₃)₂ as precursor. The enhanced capacity retention can be mainly attributed to the NiO–C composite structure, composed of NiO nanoparticles surrounded by carbon, which can accommodate the volume changes during charge–discharge and improve the electrical conductivity between the NiO nanoparticles.     

Thermoluminescence,infrared reflectivity and electron paramagnetic resonance properties of hemimorphite

Silicate mineral hemimorphite has been investigated concerning its TL, IR and EPR properties. A broad TL peak around 180 °C and a weaker and narrower peak around 360 °C were found in a sample annealed at 600 °C for 1 h and then irradiated. The deconvolution using the CGCD method revealed peaks around 132, 169, 222 and 367 °C. The reflectivity measurements showed several bands in the NIR region due to H₂O, OH and Al–OH complexes. No band was observed in the visible region. The thermal treatments were carried out from ∼110 to 940 °C and dehydration was observed, first causing a diminishing optical absorption in general and the disappearance of water and hydroxyl absorption bands. The EPR spectrum of natural hemimorphite, presented Cu²⁺ signals at g = 2.4 and g = 2.1 plus E₁′ signal superposed to Fe³⁺ signal around g = 2.0.     

Structural evolution,growth mechanism and photoluminescence properties of CuWO4 nanocrystals

Copper tungstate (CuWO₄) crystals were synthesized by the sonochemistry (SC) method, and then, heat treated in a conventional furnace at different temperatures for 1 h. The structural evolution, growth mechanism and photoluminescence (PL) properties of these crystals were thoroughly investigated. X-ray diffraction patterns, micro-Raman spectra and Fourier transformed infrared spectra indicated that crystals heat treated and 100 °C and 200 °C have water molecules in their lattice (copper tungstate dihydrate (CuWO₄·2H₂O) with monoclinic structure), when the crystals are calcinated at 300 °C have the presence of two phase (CuWO₄·2H₂O and CuWO₄), while the others heat treated at 400 °C and 500 °C have a single CuWO₄ triclinic structure. Field emission scanning electron microscopy revealed a change in the morphological features of these crystals with the increase of the heat treatment temperature. Transmission electron microscopy (TEM), high resolution-TEM images and selected area electron diffraction were employed to examine the shape, size and structure of these crystals. Ultraviolet–Visible spectra evidenced a decrease of band gap values with the increase of the temperature, which were correlated with the reduction of intermediary energy levels within the band gap. The intense photoluminescence (PL) emission was detected for the sample heat treat at 300 °C for 1 h, which have a mixture of CuWO₄·2H₂O and CuWO₄ phases. Therefore, there is a synergic effect between the intermediary energy levels arising from these two phases during the electronic transitions responsible for PL emissions.     

Structural characterization of the V2O5/TiO2 system obtained by the sol–gel method

The influence of the vanadium load and calcination temperature on the structural characteristics of the V₂O₅/TiO₂ system was studied by X-ray diffraction and X-ray absorption spectroscopy (XAS) techniques. Samples of the V₂O₅/TiO₂ system were prepared by the sol–gel method under acid conditions and calcined at different temperatures. The rutile phase was found to predominate in pure TiO₂ calcined at 450 °C as a result of the reduction of phase transition temperature promoted by the sol–gel method under acid conditions. The anatase phase became predominant at 450 °C as the amount of vanadium increased from 6 to 9 wt%. A structural change in the TiO₂ phase from predominantly anatase to totally rutile with increased calcination temperature was observed in 6 wt% samples. An analysis of the vanadium X-ray Absorption Near Edge Structure (XANES) spectra showed that the oxidation state of vanadium atoms in the samples containing 6 and 9 wt% of vanadium and calcined at 450 °C was predominantly V⁴⁺. However, the presence of V⁵⁺ atoms cannot be ruled out. A qualitative analysis of extended X-ray absorption fine structure (EXAFS) spectra of the samples containing 6 and 9 wt% of vanadium calcined at 450 °C showed that the local structure around vanadium atoms is comparable to that of VO₂ crystalline phase, in which vanadium atoms are fourfold coordinated in a distorted structure. For the sample after calcination at 600 °C, the EXAFS and XANES results showed that a significant portion of vanadium atoms were incorporated in the rutile lattice with a V_xTi_(1−x)O₂ solid solution formation. The conditions of sample preparation used here to prepare V₂O₅/TiO₂ samples associated with different amounts of vanadium and calcination temperatures proved to be useful to modifying the structure of the V₂O₅/TiO₂ system.