Fast fabrication of Ta2O5 nanotube arrays and their conversion to Ta3N5 for efficient solar driven water splitting

This work shows that highly ordered and mechanically stable micrometer-long Ta₂O₅ nanotube arrays can be fabricated by galvanostatic anodization in a few seconds. Typically, ~ 7.7 μm long nanotubes can be grown at 1.2 A cm^− 2 in only 2 s. Such nanotubes can be converted to Ta₃N₅ nanotube arrays by nitridation. Photoelectrochemical (PEC) water splitting using AM 1.5G illumination yields for the Ta₃N₅ nanotube photoanode modified with cobalt phosphate (Co–Pi) remarkable photocurrents of 5.9 mA cm ⁻² at 1.23 V_RHE and 12.9 mA cm ⁻² at 1.59 V_RHE and after Ba-doping a value of 7.5 mA cm ⁻² at 1.23 V_RHE is obtained.     

Characterization of thin InP anodic oxide layers: Correlation of morphological investigations with chemical and electrical properties

Depending on the applied electrochemical parameters, various oxide films can be grown onto InP in aqueous media. In this work, two oxide layers have been grown in borate buffer solution at pH = 9 by applying a low (0.2 mA cm⁻²) or a high (30 mA cm⁻²) current density, but a similar coulometric charge. Capacitance–voltage measurements performed before and after the anodic processes have been made to investigate the electrical properties of new interfaces, while X-ray photoelectron spectroscopy (XPS) analysis and atomic force microscopy (AFM) observations were used to access to the chemical and topographic aspects of the two oxidized surfaces. It is demonstrated that AFM observations coupled with electrochemical and XPS measurements is a good probe for the study of thin oxide on InP. A correlation between the anodization parameters and the resulting electrical and morphological aspects of the anodic layers is clearly evidenced.     

A direct borohydride–peroxide fuel cell using a Pd/Ir alloy coated microfibrous carbon cathode

A direct borohydride fuel cell with a Pd/Ir catalysed microfibrous carbon cathode and a gold-catalysed microporous carbon cloth anode is reported. The fuel and oxidant were NaBH₄ and H₂O₂, at concentrations within the range of 0.1–2.0 mol dm⁻³ and 0.05–0.45 mol dm⁻³, respectively. Different combinations of these reactants were examined at 10, 25 and 42 °C. At constant current density between 0 and 113 mA cm⁻², the Pd/Ir coated microfibrous carbon electrode proved more active for the reduction of peroxide ion than a platinised-carbon one. The maximum power density achieved was 78 mW cm⁻² at a current density of 71 mA cm⁻² and a cell voltage of 1.09 V.     

Electrically rechargeable zinc-oxygen flow battery with high power density

The development of a powerful, cyclically stable and electrically rechargeable zinc-oxygen battery with a three-electrode configuration is reported. A copper foam was used as stable substrate for zinc deposition in flowing potassium hydroxide electrolyte, while oxygen reduction and evolution were accomplished by a commercial silver electrode and a nickel foam, respectively. The cell could be charged and discharged with up to 600 mA cm^− 2, delivered a peak power density of 270 mW cm^− 2, and performed for more than 600 cycles, although short circuits by dendrite formation could not yet be completely avoided. At a current density of 50 mA cm^− 2 and a temperature of 30 °C, a promising energy efficiency of 54% was achieved.     

Investigation of immiscible alloy system of Al–Sn thin films as anodes for lithium ion batteries

The Al–Sn, which is immiscible alloy, film was prepared by e-beam deposition to explore the possibility as anode material for lithium ion batteries for the first time. The film has a complex structure with tiny Sn particles dispersed homogeneously in the Al active matrix. The diffusion coefficients of Li⁺ in these Al–Sn alloy films were determined to be 2.1–3.2 × 10⁻⁸ cm²/s by linear sweep voltammetry. The film electrode with high Al content (Al–33wt%Sn) delivered a high initial discharge capacity of 972.8 mA h g⁻¹, while the film electrode with high Sn content (Al–64wt%Sn) with an initial discharge capacity of 552 mA h g⁻¹ showed good cycle performance indicated by retaining a capacity of about 381 mA h g⁻¹ after 60 cycles. Our preliminary results demonstrate that Al–Sn immiscible alloy is a potential candidate for anodic material of lithium ion batteries.     

Fabrication of the catalytic electrodes for methanol oxidation on electrospinning-derived carbon fibrous mats

The carbon fibrous mats with high conductivity (50 S cm⁻¹) formed by carbon nanofibers with an average diameter of ∼150 nm have been fabricated by thermally treating the electrospun polyacrylonitrile fibers. The platinum clusters are electrodeposited on the carbon nanofibrous mats (CFMs) by multi-cycle CV method. In contrast to the catalytic peak current of methanol oxidation on commercial catalyst (185 mA mg⁻¹ Pt), the catalytic peak current on optimum Pt/CFM electrode reaches to ∼420 mA mg⁻¹ Pt despite of the large size (50–200 nm) of the Pt clusters, revealing that the special structure of carbon fibrous mats is favorable to improve the performance of catalyst.     

Visible light active hydrogen modified (HM)-n-TiO2 thin films for photoelectrochemical splitting of water

Visible light active hydrogen modified n-type titanium oxide (HM-n-TiO₂) thin films were synthesized by thermal oxidation of Ti metal sheet (Alfa Co. 0.25 mm thick) in an electric oven followed by incorporation of hydrogen electrochemically under cathodic polarization at ?1.6 V vs Pt. The photoresponse of the HM-n-TiO₂ was evaluated by measuring the rate of water splitting reaction to hydrogen and oxygen in terms of photocurrent density, J_p. The optimized electric oven-made n-TiO₂ and HM-n-TiO₂ photoelectrodes showed photocurrent densities of 0.2 mA cm^?2 and 1.60 mA cm^?2, respectively, at a measured potential of ?0.4 V vs Pt at illumination intensity of 100 mW cm^?2 from a 150 W xenon lamp. This indicated an eightfold increase in photocurrent density for HM-n-TiO₂ compared to oven-made n-TiO₂ at the same measured electrode potential. The band-gap energy of HM-n-TiO₂ was found to be 2.7 eV compared to 2.82 eV for electric oven-made n-TiO₂ and a mid-gap band at 1.67 eV above the valence band was also observed. The HM-n-TiO₂ thin film photoelectrodes were characterized using photocurrent density under monochromatic light illumination and UV–Vis spectral measurements.     

Electrochemical characterization of vertical arrays of tin nanowires grown on silicon substrates as anode materials for lithium rechargeable microbatteries

Vertical arrays of one-dimensional tin nanowires on silicon dioxide (SiO₂)/silicon (Si) substrates have been developed as anode materials for lithium rechargeable microbatteries. The process is complementary metal-oxide-semiconductor (CMOS) compatible for fabricating on-chip microbatteries. Nanoporous anodized aluminum oxide (AAO) templates integrated on SiO₂/Si substrates were employed for fabrication of tin nanowires resulting in high surface area of anodes. The microstructure of these nanowire arrays was investigated by scanning electron microscopy and X-ray diffraction. The electrochemical tests showed that the discharge capacity of about 400 mA h g⁻¹ could be maintained after 15 cycles at the high discharge/charge rate of 4200 mA g⁻¹.     

Molybdenum electrodes for hydrogen production by water electrolysis using ionic liquid electrolytes

The hydrogen production by water electrolysis was tested with different electrocatalysts (molybdenum, nickel, iron alloys containing chromium, manganese and nickel) using aqueous solutions of ionic liquid (IL) like 1-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF₄). The hydrogen evolution reaction (HER) was performed at room temperature in a potential of −1.7 V (PtQRE). A Hoffman cell apparatus was used to water electrolysis with current density values, j, between 14.6 mA cm⁻² (for Ni electrode) and 77.5 mA cm⁻² (for Mo electrode). The system efficiency was very high for all electrocatalysts tested, between 97.0% and 99.2%. The energy activation values of HER was determined in an aqueous solution of BMI.BF₄ 10 vol.%, using platinum (23.40 kJ mol⁻¹) and Mo (9.22 kJ mol⁻¹) as electrocatalysts. The results show that the hydrogen production in IL electrolyte can be carried out with cheap material at room temperature, which makes this method economically attractive.     

Electrochemical properties of liquid electrolyte added quasi-solid state TiO2 dye-sensitized solar cells

In this study a process has been introduced to replace traditional liquid or solid electrolyte coatings on dye-sensitized photoelectrode in solar cells. This process has more efficient diffusion of electrolyte, hence higher sensitivity. Better interfacial contact between polymer electrolyte and TiO₂ photoelectrode had improved electrochemical response and ionic conductivity of cell. Conductivity of this electrode was 9.33 × 10⁻³ S cm⁻¹ (at room temperature), which is much higher than the using traditional process for addition of electrolytes. It has 0.68 V open-circuit voltage and 3.19 mA cm⁻² short-circuit current density. Energy conversion efficiency of this cell was about 37% higher than the cell developed with traditional processes under constant light intensity (45 mW cm⁻²).     

Thin films composed of irregular micro-block arrays of closely packed CdS nanoparticles for enhanced photoelectrochemical performance

CdS is a very important semiconductor, and various micro-/nano-structured forms of CdS have been fabricated with the aim of improving its photoelectrochemical performance. We report here for the first time the preparation of a CdS film consisting of irregular micro-block arrays of closely packed CdS nanoparticles. It performs outstandingly well as a photoanode because it possesses the advantages of both arrays and nanoparticles. This CdS film is prepared simply by a combination of reaction and assembly at the gas/liquid interface (RAG/L) with successive ionic layer adsorption and reaction (SILAR), requiring no templates or expensive equipment. In this approach, the nanopores in the film of loosely aggregated CdS nanoparticles produced by RAG/L are filled by CdS nanoparticles via SILAR, forming a compact CdS film. Network micro-cracks form in the compact CdS film due to calcination caused by differential thermal expansion compared with the substrate, and these cut the CdS film into irregular micro-block arrays. This micro-/nano-structure in the prepared CdS film improves its capacity for visible light absorption, facilitates the generation/separation of excited charges, and enhances mass transfer. In an alkaline solution of methanol, the prepared CdS film exhibits the highest saturation photocurrent density (6.5 mA cm^− 2) ever reported on CdS-based photoanodes under visible light illumination.     

Mesoporous Fe2O3 nanoparticles as high performance anode materials for lithium-ion batteries

This work introduces an effective, inexpensive, and large-scale production approach to the synthesis of Fe₂O₃ nanoparticles with a favorable configuration that 5 nm iron oxide domains in diameter assembled into a mesoporous network. The phase structure, morphology, and pore nature were characterized systematically. When used as anode materials for lithium-ion batteries, the mesoporous Fe₂O₃ nanoparticles exhibit excellent cycling performance (1009 mA h g^− 1 at 100 mA g^− 1 up to 230 cycles) and rate capability (reversible charging capacity of 420 mA h g^− 1 at 1000 mA g^− 1 during 230 cycles). This research suggests that the mesoporous Fe₂O₃ nanoparticles could be suitable as a high rate performance anode material for lithium-ion batteries.     

One-step synthesis of hollow structured Si/C composites based on expandable microspheres as anodes for lithium ion batteries

Si/C composites of carbon hollow structures loaded with Si nanoparticles (NPs) (Si/C-HSs) were prepared by one-step pyrolysis of a mixture of Si NPs and expandable microspheres (EMs). For the Si/C-HSs, hollow carbon shells with rough surfaces were formed by directly carbonizing the polymer shells of EMs, and the Si NPs fell into the void space or were loaded on the rough surfaces of the carbon shells. The EM-based carbon shells accommodated the volume expansion of the Si NPs and improved the electrical conductivity of the composites. As a result, the Si/C-HSs exhibited a high capacity (initial reversible capacity: 854.4 mAh g^− 1 at 300 mA g^− 1), stable cycling performance (capacity retention: 80% after 50 cycles), and excellent rate capability.     

Bioelectrocatalytic formate oxidation and carbon dioxide reduction at high current density and low overpotential with tungsten-containing formate dehydrogenase and mediators

We show a great possibility of mediated enzymatic bioelectrocatalysis in the formate oxidation and the carbon dioxide (CO₂) reduction at high current densities and low overpotentials. Tungsten-containing formate dehydrogenase (FoDH1) from Methylobacterium extorquens AM1 was used as a catalyst and immobilized on a Ketjen Black-modified electrode. For the formate oxidation, a high limiting current density (j_lim) of ca. 24 mA cm^− 2 was realized with a half wave potential (E_1/2) of only 0.12 V more positive than the formal potential of the formate/CO₂ couple (E°′_CO2) at 30 °C in the presence of methyl viologen (MV^2 +) as a mediator, and j_lim reached ca. 145 mA cm^− 2 at 60 °C. Even when a viologen-functionalized polymer was co-immobilized with FoDH1 on the porous electrode, j_lim of ca. 30 mA cm^− 2 was attained at 60 °C with E_1/2 = E°′_CO2 + 0.13 V. On the other hand, the CO₂ reduction was also realized with j_lim ≈ 15 mA cm^− 2 and E_1/2 = E°′_CO2 − 0.04 V at pH 6.6 and 60 °C in the presence of MV^2 +.     

Platinum nanoparticles supported on nitrobenzene-functionalised graphene nanosheets as electrocatalysts for oxygen reduction reaction in alkaline media

A systematic study on the electrocatalytic properties of Pt nanoparticles supported on nitrobenzene-modified graphene (Pt-NB/G) as catalyst for oxygen reduction reaction (ORR) in alkaline solution was performed. Graphene nanosheets were spontaneously grafted with nitrophenyl groups using 4-nitrobenzenediazonium salt. The electrocatalytic activity towards the ORR and stability of the prepared catalysts in 0.1 M KOH solution have been studied and compared with that of the commercial Pt/C catalyst. The results obtained show that the NB-modified graphene nanosheets can be good Pt catalyst support with high stability and excellent electrocatalytic properties. The specific activity of Pt-NB/G for O₂ reduction was 0.184 mA cm⁻², which is very close to that obtained for commercial 20 wt% Pt/C catalyst (0.214 mA cm⁻²) at 0.9 V vs. RHE. The Pt-NB/G hybrid material promotes a four-electron reduction of oxygen and can be used as a promising cathode catalyst in alkaline fuel cells.     

Studies on polypyrrole modified nafion membrane for vanadium redox flow battery

In order to prevent the vanadium crossover and preferential water transfer in all-vanadium redox flow battery (VRFB), three methods – electrolyte soaking, oxidation polymerisation and Electrodeposition, were used to modify Nafion 117 membranes using pyrrole. The surface of the modified membranes was uniform and even, and the membranes were characterised in terms of morphology, membrane area resistance, vanadium permeability and water transfer property. The properties of all the modified membranes were improved greatly. The membranes modified by Electrodeposition showed a best combination of the membrane resistance, vanadium permeability and water transfer property, the experimental results showed that the V(IV) ion permeability of polypyrrole modified Nafion membranes by Electrodeposition at the conditions of 0.025 mA cm⁻² and 0 ^°C for 60 min reduced more than 5 times from 2.87 × 10⁻⁶ cm² min⁻¹ to 5.0 × 10⁻⁷cm² min⁻¹, and the water transfer property decreased more than 3 times from 0.72 ml/72 h cm² to 0.22 ml/72 h cm². All above properties made the modified Nafion membranes more applicative in the VRFB system. This paper also reported other methods for Nafion membrane modification and the influences of the deposition conditions on the properties of the membrane selectivity and water transfer.     

Ni infiltrated Sr2Fe1.5Mo0.5O6-δ-Ce0.8Sm0.2O1.9 electrode for methane assisted steam electrolysis process

It is an effective way to substitute air to methane in the anode of solid oxide electrolysis cells to reduce the electrical consumption for simultaneously producing H₂ and high-quality syngas. In the methane assisted mode, the thermodynamic properties and Nernst potential exhibit one order of magnitude reduction of applied voltage to produce comparable electrolysis current. Ni catalysts are infiltrated to the SFM-SDC anode to improve the catalytic properties for methane assisted steam electrolysis. After Ni infiltration, surface oxygen exchange coefficient is effectively accelerated from 3.03 × 10^− 5 to 2.20 × 10^− 4 cm s^− 1, and the current density is significantly enhanced from − 487 to − 1022 mA cm^− 2 at 850 °C and 0.5 V.     

Electroless decoration of macroscale foam with nickel nano-spikes: A scalable route toward efficient catalyst electrodes

Electroless deposition of anisotropic catalyst layers is introduced as an efficient approach to fabricate high-performing multiscale electrode architectures. In the present study, a biomass-derived, solidified foam is coated with nickel nano-spikes. This results in an amplification of the surface area and an introduction of catalytic functionality, while the favorable mass transfer properties of the porous support are retained. Both the substrate and the metal film are produced using simple, readily scalable processes. The support is prepared from liquefied sawdust by self-foaming, and nickel deposition is performed by immersion in a hydrazine-based plating bath. The favorable functional properties of the nickel-coated foam are demonstrated in enzyme-free glucose sensing. Due to the large surface area and the high activity of the nickel nanofilm, an outstanding sensitivity of 8.1 mA mM^− 1 cm^− 2 and a low detection limit of 60 nM were achieved.     

Photoelectrochemical determination of inorganic mercury ions based on energy transfer between CdS quantum dots and Au nanoparticles

A novel photoelectrochemical (PEC) sensor for mercury ions (Hg^2 +) was fabricated based on the energy transfer (ET) between CdS quantum dots (QDs) and Au nanoparticles (NPs) with the formation of T–Hg^2 +–T pairs. In the presence of Hg^2 + ions, a T-rich single-strand (ss) DNA labeled with Au NPs could hybridize with another T-rich ssDNA anchored on the CdS QDs modified electrode, through T–Hg^2 +–T interactions, rendering the Au NPs in close proximity with the CdS QDs and hence the photocurrent decrease due to the ET between the CdS QDs and the Au NPs. Under the optimal condition, the photocurrent decrease was proportional to the Hg^2 + concentration, ranging from 3.0 × 10^− 9 to 1.0 × 10^− 7 M, with the detection limit of 6.0 × 10^− 10 M.     

Highly active Co-doped LaMnO3 perovskite oxide and N-doped carbon nanotube hybrid bi-functional catalyst for rechargeable zinc–air batteries

Herein, non-precious cobalt doped lanthanum manganese perovskite oxide nanoparticles are used as a growth substrate for nitrogen-doped carbon nanotubes to form efficient and durable hybrid bi-functional catalyst (LMCO/NCNT). LMCO/NCNT demonstrates significantly enhanced onset and half-wave oxygen reduction reaction (ORR) potentials (− 0.11 and − 0.24 V vs. SCE, respectively), and oxygen evolution reaction (OER) current density (27 mA cm^− 2 at 0.9 V vs. SCE). Likewise, practical rechargeable zinc–air battery testing using atmospheric air reveals superior discharge voltages obtained with LMCO/NCNT, particularly at current densities higher than 30 mA cm^− 2, and significantly lower charge voltages at all current densities tested, compared to state-of-art commercial platinum on carbon catalyst. In addition, very stable charge and discharge voltages of 2.2 and 1.0 V, respectively, are obtained over 60 cycles. The excellent performance and durability of the hybrid catalyst are attributed to very uniformly distributed LMCO nanoparticles on the surface of NCNT resulting in enhanced surface area and material utilization.