Synthesis of nanosized TiO2/SiO2 particles using microwave processes and their photocatalytic activity on the decomposition of orange II

The nanosized titania and TiO₂/SiO₂ particles were prepared by the microwave-hydrothermal method. The effect of physical properties TTIP/TEOS ratio and calcination temperature has been investigated. The major phase of the pure TiO₂ particle is of the anatase structure, and a rutile peak was observed above 800°C. In TiO₂/SiO₂ particles, however, no significant rutile phase was observed, although the calcination temperature was 900°C. No peaks for the silica crystal phase were observed at either silica/titania ratio. The crystallite size of TiO₂/SiO₂ particles decreases as compared to pure TiO₂ at high calcination temperatures. The TiO₂/SiO₂ particles show higher activity on the photocatalytic decomposition of orange II as compared to pure TiO₂ particles.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

Aerosol-assisted synthesis of mesoporous titania nanoparticles with high surface area and controllable phase composition

Mesoporous titania nanoparticles (denoted as MTN) with high surface area (e.g., 252 m² g⁻¹) were prepared using tetrapropyl orthotitanate (TPOT) as a titania precursor and 10–20 nm or 20–30 nm silica colloids as templates. Co-assembly of TPOT and silica colloids in an aerosol-assisted process and immediate calcination at 450 °C resulted in anatase/silica composite nanoparticles. Subsequent removal of the silica colloids from the composite by NaOH solution created mesopores in the TiO₂ nanoparticles with pore size corresponding to that of silica colloids. Effects of silica colloids’ contents on MTN porosity and crystallites’ growth at a higher calcination temperature (e.g., 1000 °C) were investigated. Silica colloids suppressed the growth of TiO₂ crystallites during calcination at a higher calcination temperature and controllable contents of the silica colloids in precursor solution resulted in various atomic ratios of anatase to rutile in the calcinated materials. The mesostructure and crystalline structure of these titania materials were characterized by transmission electron microscope (TEM), scanning electron microscope (SEM), X-ray diffraction (XRD), differential thermal analysis (DTA)-thermo-gravimetric analysis (TGA), and N₂ sorption.     

DSC investigation of nanocrystalline TiO<Subscript>2</Subscript> powder

The aim of the article is to investigate the influence of particle size on titanium dioxide phase transformations. Nanocrystalline titanium dioxide powder was obtained through a hydrothermal procedure in an aqueous media at high pressure (in the range 25–100 atm) and low temperature (≤200 °C). The as-prepared samples were characterized with respect to their composition by ICP (inductive coupled plasma), structure and morphology by XRD (X-ray diffraction), and TEM (transmission electron microscopy), thermal behavior by TG (thermogravimetry) coupled with DSC (differential scanning calorimetry). Thermal behavior of nanostructured TiO₂ was compared with three commercial TiO₂ samples. The sequence of brookite–anatase–rutile phase transformation in TiO₂ samples was investigated. The heat capacity of anatase and rutile in a large temperature range are reported.     

Preparation of nanocrystalline TiO<Subscript>2</Subscript> powders for photocatalytic oxidation of phenol

Nanocrystalline TiO₂ powders in the anatase, rutile, and mixed phases prepared by hydrolysis of TiCl₄ solution were of ultrafine size (<7.2 nm) with high specific surface areas in the range 167 to 388 m²/g. In the photocatalytic degradation of phenol as model reaction, the photocatalytic properties of TiO₂ nanoparticles were evaluated by use of UV–vis absorption spectroscopy and total organic carbon (TOC) content. The synthetic mixed-phase TiO₂ powder calcined at 400 °C had higher activity than pure anatase or rutile; it degraded more than 90% phenol to CO₂ (evaluated by TOC) after irradiation with near UV light for 90 min at a catalyst loading of 0.4 g/L. The TOC results indicated that rutile TiO₂ crystallites of particle size 7.2 nm resulted in much better photocatalytic performance than particles of larger size. This result suggested that some intermediates, not determined by UV–vis absorption spectroscopy, existed in the solution after the photocatalytic process over the rutile TiO₂ photocatalysts of larger crystallite size.     

Synthesis,Characterization and Photocatalytic Behavior of SiO2@nitrized-TiO2 Nanocomposites Obtained by a Straightforward Novel Approach

We report on the facile synthesis of SiO₂@nitrized-TiO₂ nanocomposite (NST) by calcination of TiO₂ xerogel with OctaAmmonium POSS® (N-POSS; POSS=polyhedral oligomeric silsesquioxanes). The as-obtained nanoporous mixed oxide is constituted by uniformly distributed SiO₂ and nitrized-TiO₂, where the silica component is present in an amorphous state and TiO₂ in an anatase/rutile mixed phase (92.1 % vs. 7.9 %, respectively) with very small anatase crystallites (3.7 nm). The TiO₂ lattice is nitrized both at interstitial and substitutional positions. NST features a negatively charged surface with a remarkable surface area (406 m² g⁻¹), endowed with special adsorption capabilities towards cationic dyes. Its photocatalytic behavior was tested by following the degradation of standard aqueous methylene blue and methyl orange solutions under UV and visible light irradiation, according to ISO 10678:2010. For comparison, analogous investigations were carried out on a silica-free N−TiO₂, obtained by using NH₄Cl as nitrogen source.     

Effect of annealing temperatures and of high content of the iron ion (Fe<Superscript>3+</Superscript>)-doping on transition anatase–rutile phase of nanocrystalline TiO<Subscript>2</Subscript> thin films prepared by sol–gel spin coating

Titanium dioxide doped with iron (III) was prepared by sol–gel Spin Coating method. The phase structures, morphologies, particle size of the doped TiO₂ have been characterized by X-ray diffraction (XRD), Raman spectroscopy, atomic force microscopy (AFM) and ultraviolet–visible (UV–Vis) spectrophotometer. The XRD and Raman results show that the 10% Fe³⁺-doped TiO₂ thin films crystallize in anatase phase between 600 and 800 °C, and into the anatase–rutile phase at 1,000 °C, and further into the rutile phase when the content of Fe³⁺ increases (20%). The grain size calculated from XRD patterns shows that the crystallinity of the obtained anatase particles increased from 39.4 to 43.4 nm as the temperature of annealing increase, whereas the size of rutile crystallites increases, with increasing Fe³⁺ concentrations from 36.9 to 38.1 nm. The AFM surface morphology results confirmed that the particle size increases by increasing the annealing temperature and also with an increasing of Fe³⁺ content. The optical band gap (E _g) of the films was determined by the UV–Vis spectrophotometer. We have found that the optical band gap decreased with an increasing of annealing temperatures and also with an increasing of Fe³⁺ content.     

Electronic Structure and Size of TiO2 Nanoparticles of Controlled Size Prepared by Aerosol Methods

Summary.  A complete characterization of nanostructures has to deal both with electronic structure and dimensions. Here we present the characterization of TiO₂ nanoparticles of controlled size prepared by aerosol methods. The electronic structure of these nanoparticles was probed by X-ray absorption spectroscopy (XAS), the particle size by atomic force microscopy (AFM). XAS spectra show that the particles crystallize in the anatase phase upon heating at 500°C, whereas further annealing at 700°C give crystallites of 70% anatase and 30% rutile phases. Raising the temperature to 900°C results in a complete transformation of the particles to rutile. AFM images reveal that the mean size of the anatase particles formed upon heating at 500°C is 30 nm, whereas for the rutile particles formed upon annealing at 900°C 90 nm were found. The results obtained by these techniques agree with XRD data. Received October 5, 2001. Accepted (revised) December 6, 2001     

A study on the effect of starting material phase on the production of trititanate nanotubes

Mixed phase TiO₂ powders of different composition and particle size were subjected to the hydrothermal reaction with 10 M NaOH. It was found that the anatase phase component of the starting material is easily converted to trititanate nanotubes at 140 °C. At this temperature the rutile phase remains unreacted, however at 170 °C it reacts to form trititanate plates and belts. When the reaction time is increased to 7 days, all the TiO₂ is converted to trititanate and the morphology is exclusively nanoplates and belts, with the tube phase destroyed. Many researchers have observed some heterogeneity in their reaction products, but have mainly focussed on the nanotubes. We observed that the tubes are only prepared from the anatase phase component of a TiO₂ precursor, whereas the rutile component produces trititanate plates and sheets, irrespective of the reaction length. The particle size affects the rate of reaction, resulting in the phase transition being more easily visible in the reactions starting with the larger TiO₂ particle size.     

Microstructure and Photocatalytic Property of SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> Under Various Process Condition

Nanophase silica-titania particles were prepared by two different synthetic routes, namely, sol–gel and hydrothermal processing. The crystallinity and crystallographic phases, particle size and surface area of the materials were controlled by varying the calcination temperature, and/or the ratio of Si to Ti. It was determined by XRD that the crystallite sizes of SiO₂-TiO₂ prepared by sol–gel and hydrothermal processing decreased from 11 to 6 nm and 12 to 9 nm, respectively, as the mole fraction of silica was increased from 0.1 to 0.4. It is proposed that the presence of the amorphous silica suppresses the growth of anatase TiO₂ grains and their phase transformation to rutile. The photocatalytic decomposition rate of 1,4-dichlorobenzene (DCB) in aqueous solution with the sol–gel derived SiO₂-TiO₂ powder prepared at 750 °C was about 10 ± 5% higher than that observed with Degussa P25, whereas the SiO₂-TiO₂ samples prepared by hydrothermal processing at 250 °C showed a slightly lower decomposition rate than P25.     

Structural characterization of Fe/Ti oxide photocatalysts by X-ray,ESR, and Mössbauer methods

The polycrystalline solids TiO₂Fe₂O₃, with iron contents in the range 0–10 at.%, prepared by coprecipitation and by impregnation, and treated in air at temperatures in the range 500–1000°C, have been studied by X-ray, ESR, and Mössbauer methods. The TiO₂ in the samples treated at 800 and 1000°C always forms the rutile phase and the Fe³⁺ has a rather low solubility in it (～0.1 at.%). The Fe³⁺ in excess forms the antiferromagnetic pseudobrookite phase (Fe₂TiO₅). The samples treated at 500 and 650°C show a dependence on the preparation method. Those prepared by coprecipitation give at 500°C the pure anatase phase in which the Fe³⁺ has a higher solubility (≥ 1%); those prepared by impregnation give the anatase phase accompanied by a variable amount of rutile. The treatment at 650°C provokes the partial transformation of anatase to rutile and the complete development of the Fe₂TiO₅ phase. The relevance of these results to the photocatalytic properties shown by these solids for the photoreduction of dinitrogen to ammonia is discussed.     

Synthesis and characterization of high surface area TiO2/SiO2 mesostructured nanocomposite

Recently titania synthesis was reported using various structuration procedures, leading to the production of solid presenting high surface area but exhibiting moderate thermal stability. The study presents the synthesis of TiO₂/SiO₂ nanocomposites, a solid that can advantageously replace bulk titania samples as catalyst support. The silica host support used for the synthesis of the nanocomposite is a SBA-15 type silica, having a well-defined 2D hexagonal pore structure and a large pore size. The control of the impregnation media is important to obtain dispersed titania crystals into the porosity, the best results have been obtained using an impregnation in an excess of solvent. After calcination at low temperature (400 °C), nanocomposites having titania nanodomains (～2–3 nm) located inside the pores and no external aggregates visible are obtained. This nanocomposite exhibits high specific surface area (close to that of the silica host support, even with a titania loading of 55 wt.%) and a narrow pore size distribution. Surprisingly, the increase in calcination temperature up to 800 °C does not allow to detect the anatase to rutile transition. Even at 800 °C, the hexagonal mesoporous structure of the silica support is maintained, and the anatase crystal domain size is evaluated at ～10 nm, a size close to that of the silica host support porosity (8.4 nm). Comparison of their physical properties with the results presented in literature for bulk samples evidenced that these TiO₂/SiO₂ solids are promising in term of thermal stability.     

Preparation of nanocrystalline anatase TiO2 using basic sol-gel method

Nanocrystalline titanium dioxide particles with anatase structure and high thermal stability have been synthesized using the basic sol-gel method. The particle size and morphology were refined under hydrothermal conditions in the presence of different concentrations of tetramethylammonium hydroxide (TMAH) at 210°C and 230°C. XRD and TEM analysis showed that the TiO₂ particles obtained were homogeneous and monodispersive at low contents of TMAH. All intense peaks, clearly observed in the XRD patterns, were assigned to the anatase phase and no rutile phase was observed. At high contents of TMAH, nanoscale small (10–30 nm) and larger (>100 nm) TiO₂ particles were one-pot synthesized. The nanocrystalline TiO₂ particles synthesized by this method have good thermal stability. With the sintering temperature of up to 650°C, all the XRD peaks maintained good agreement with the anatase reference data.     

Sol-Gel Derived TiO2-SiO2 Fibres

TiO₂−SiO₂ fibres with 0, 5, 10 and 20 volume % SiO₂ have been prepared by drawing from a gel followed by sintering at different temperatures. Nearly one meter long fibres can be drawn easily in conditions of about 50% relative humidity. Addition of SiO₂ inhibits the crystallisation of TiO₂ and also the anatase → rutile transformation and improves the strength of the fibres. While the pure TiO₂ fibres are brittle, those with 5, 10 and 20 volume % SiO₂ are flexible and strong. Tensile strength values as high as 3 GPa have been achieved in the 10 volume % SiO₂−TiO₂ fibres. Fibres heated above 900°C are brittle. The shape of the cross section of the fibres is found to depend on their diameters.     

Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Crystallization Behavior of SiO2-TiO2 Sol-Gel Thin Films

The aim of this work was to investigate the crystallization behavior of thin films of SiO₂−TiO₂ made by the sol-gel process as function of the TiO₂ content and the temperature and time of heat treatment. Precursor solutions were prepared by hydrolysis of TEOS (tetraethoxysilane) and TPOT (titaniums tetraisopropoxide). Multilayer films were spun on single crystal silicon wafers. The compositions studied were (on a molar percentage basis) 20TiO₂−80SiO₂, 30TiO₂−70SiO₂, 40TiO₂−60SiO₂ and pure TiO₂. The films were heat treated at different temperatures between 300°C and 1200°C, for different periods of time (30 s-90 h). The crystallization kinetics were followed by micro-Raman spectrometry. Grazing incidence X-ray diffraction showed that the films crystallized into one or both of two crystalline phase of TiO₂: anatase and rutile (for pure TiO₂ only). The volume fractions of the crystalline phase varied from very low values (<1%), up to 100%, for a TiO₂ sample heat treated at 800°C for 8 hours. The results show that the volume fraction of crystalline phase is strongly influenced by the heat treatment temperature and also, to a smaller extent, by the heat treatment time. The most important parameter, however, is the composition of the films: the higher their TiO₂ concentration, the lower is the crystallization temperature and the larger is the crystallized fraction.     

Photoinduced hydrophilic and photocatalytic response of hydrothermally grown TiO2 nanostructured thin films

It is demonstrated that nanostructured titanium (IV) oxide (TiO₂) films can be deposited on glass substrates at 95 °C using hydrothermal growth, their properties being greatly affected by the substrate materials. Anatase TiO₂ films grown on ITO for deposition period of 50 h were observed to exhibit a very efficient, reversible light-induced transition to super-hydrophilicity, reaching a nearly zero contact angle. Enhanced photocatalytic activity (65%) was found for the rutile TiO₂ samples grown on microscope glass, possibly due to their higher roughness with respect to anatase grown on ITO. The effect of the substrate material used is discussed in terms of the TiO₂ phase and morphology control, for the best photoinduced hydrophilic and photocatalytic performance of the samples.     

The influence of titanium dioxide phase composition on dyes photocatalysis

A comparative study of TiO₂ powders prepared by sol–gel methods is presented. Titanium tetraisopropoxide was used as the precursor for the sol–gel processes. The effects of the annealing treatment on phase, crystallite size, porosity and photodegradation of dyes (methyl orange and methylene blue) were studied. The phase structure, microstructure and surface properties of the films were characterized by using X-ray diffraction (XRD) and Atomic Force Microscopy (AFM). The X-ray diffraction was used for crystal phase identification, for the accurate estimation of the anatase–rutile ratio and for the crystallite size evaluation of each polymorph in the samples. It was found that the only TiO₂ anatase phase of the synthesized TiO₂ develops below 500 °C, between 600 and 800 °C the anatase coexist with rutile and above 800 °C only the rutile phase was found in the samples. Attention has been paid not only to crystal structures, but also to the porosity, the particle size and the photocatalytic properties. However, the annealing temperature was found to have significant influence on the photocatalytic properties. Different TiO₂ doctor blade thin films were obtained mixing the sol gel powder (100% anatase) and TiO₂ Aldrich with TiO₂ Degussa P25. The surfactant (Triton X100 or sodium dodecyl sulfate) affects the packing density of the particles during deposition and the photocatalytic degradation efficiency of the dyes. The photocatalytic degradation kinetics of methyl orange and methylene blue using TiO₂ thin film were investigated.     

Temperatures and kinetics of anatase to rutile transformation in doped TiO<Subscript>2</Subscript> heated in microwave field

The influence of aliovalent ions such as Mn, Cr, Fe, Mo, and V on the temperature and kinetics of anatase to rutile phase transformation in TiO₂ heated in microwave field was studied in this work. The results indicated that heat treatment method and dopants considerably affected the anatase-to-rutile phase transition temperature and kinetics of transformation. The activation energy for anatase to rutile transformation of TiO₂ derived from the isothermal data was found to be 328.4 kJ mol^–1, which was considerably reduced by the addition of dopants in TiO₂ matrix. The activation energy for Mo, Mn and V doped samples was 252.0, 101.3 and 96.4 kJ mol^–1, respectively.     

Preparation of TiO<Subscript>2</Subscript> nanofibers immobilized on quartz substrate by electrospinning for photocatalytic degradation of ranitidine

The photocatalytic activity of TiO₂ nanofibers immobilized on quartz substrates was investigated by evaluating the decomposition of organic pollutants. TiO₂ nanofibers were synthesized by electrospinning the Ti-precursor/polymer mixture solution, followed by hot-pressing for enhancing the adhesion of TiO₂-nanofiber films to the substrates. TiO₂ started to crystalize in the anatase form at 500 °C and reached the optimal photocatalytic anatase/rutile phase ratio of 70:30 at a calcination temperature of 600 °C. The TiO₂-nanofiber film was demonstrated to be an efficient photocatalyst by ranitidine decomposition under UV illumination and was proven to have a comparable photocatalytic activity with the well-known Degussa P25 nanoparticulate photocatalyst and excellent recyclability during 10 cycles of photocatalytic operation, indicating no loss of TiO₂ nanofibers during photocatalytic operations.