Graphene oxide doped polyaniline for supercapacitors

A novel high-performance electrode material based on fibrillar polyaniline (PANI) doped with graphene oxide sheets was synthesized via in situ polymerization of monomer in the presence of graphene oxide, with a high conductivity of 10 S cm^?1 at 22 °C for the obtained nanocomposite with a mass ratio of aniline/graphite oxide, 100:1. Its high specific capacitance of 531 F/g was obtained in the potential range from 0 to 0.45 V at 200 mA/g by charge–discharge analysis compared to 216 F/g of individual PANI. The doping and the ratio of graphene oxide have a pronounced effect on the electrochemical capacitance performance of the nanocomposites.     

Synthesis and characterization of a nanocomposite of goethite nanorods and reduced graphene oxide for electrochemical capacitors

We report a one-step synthesis of a nanocomposite of goethite (α-FeOOH) nanorods and reduced graphene oxide (RGO) using a solution method in which ferrous cations serve as a reducing agent of graphite oxide (GO) to graphene and a precursor to grow goethite nanorods. As-prepared goethite nanorods have an average length of 200 nm and a diameter of 30 nm and are densely attached on both sides of the RGO sheets. The electrochemical properties of the nanocomposite were characterized by cyclic voltammetry (CV) and chronopotentiometry (CP) charge–discharge tests. The results showed that goethite/RGO composites have a high electrochemical capacitance of 165.5 F g^?1 with an excellent recycling capability making the material promising for electrochemical capacitors.     

Novel core–shell SDC/amorphous Na2CO3 nanocomposite electrolyte for low-temperature SOFCs

Novel core–shell SDC (Ce_0.8Sm_0.2O_1.9)/amorphous Na₂CO₃ nanocomposite was prepared for the first time. The core–shell nanocomposite particles are smaller than 100 nm with amorphous Na₂CO₃ shell of 4–6 nm in thickness. The nanocomposite electrolyte shows superionic conductivity above 300 °C, where the conductivity reaches over 0.1 S cm⁻¹. Such high conductive nanocomposite has been applied in low-temperature solid oxide fuel cells (LTSOFCs) with an excellent performance of 0.8 W cm⁻² at 550 °C. A new potential approach of designing and developing superionic conductors for LTSOFCs was presented to develop interface as ‘superionic highway’ in two-phase materials based on coated SDC.     

Iron (III) nanocomposites for enzyme-less biomimetic cathode: A promising material for use in biofuel cells

In this paper, we discuss the synthesis and electrochemical properties of a new material based on iron oxide nanoparticles stabilized with poly(diallyldimethylammonium chloride) (PDAC); this material can be used as a biomimetic cathode material for the reduction of H₂O₂ in biofuel cells. A metastable phase of iron oxide and iron hydroxide nanoparticles (PDAC–FeOOH/Fe₂O₃-NPs) was synthesized through a single procedure. On the basis of the Stokes–Einstein equation, colloidal particles (diameter: 20 nm) diffused at a considerably slow rate (D = 0.9 × 10^? 11 m s^? 1) as compared to conventional molecular redox systems. The quasi-reversible electrochemical process was attributed to the oxidation and reduction of Fe³⁺/Fe²⁺ from PDAC–FeOOH/Fe₂O₃-NPs; in a manner similar to redox enzymes, it acted as a pseudo-prosthetic group. Further, PDAC–FeOOH/Fe₂O₃-NPs was observed to have high electrocatalytic activity for H₂O₂ reduction along with a significant overpotential shift, ΔE = 0.68 V from ? 0.29 to 0.39 V, in the presence and absence of PDAC–FeOOH/Fe₂O₃-NPs. The abovementioned iron oxide nanoparticles are very promising as candidates for further research on biomimetic biofuel cells, suggesting two applications: the preparation of modified electrodes for direct use as cathodes and use as a supporting electrolyte together with H₂O₂.     

Electrografting of amino-TEMPO on graphene oxide and electrochemically reduced graphene oxide for electrocatalytic applications

4-Amino-2,2,6,6-tetramethyl-1-piperridine N-oxyl (4-amino-TEMPO), an electroactive nitroxide radical, was attached to the surface of graphene oxide (GO) and electrochemically reduced graphene oxide (ERGO) modified glassy carbon electrode by a simple, rapid and green electrografting method. The electroactive interfaces were analyzed by X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV). The calculated surface coverage for 4-amino-TEMPO is up to 1.55 × 10^− 9 mol·cm^− 2. The modified electroactive interface exhibited excellent electrocatalytic activity towards the electro-oxidation of reduced glutathione (GSH) and hydrogen peroxide (H₂O₂).     

A sensitivity-controlled hydrogen peroxide sensor based on self-assembled Prussian Blue modified electrode

In this communication, a hydrogen peroxide (H₂O₂) sensor based on self-assembled Prussian Blue (PB) modified electrode was reported. Thin film of PB was deposited on the electrode by self-assembly process including multiple sequential adsorption of ferric ions and hexacyanoferrate ions. The as-prepared PB modified electrode displayed sufficient stability for practical sensing application. At an applied potential of ?0.05 V vs. Ag/AgCl (sat. KCl), PB modified electrode with 30 layers exhibited a linear dependence on H₂O₂ concentration in the range of 1 × 10^?6–4 × 10^?4 M (r = 0.9998) with a sensitivity of 625 mA M^?1 cm^?2. It was found that the sensitivity of H₂O₂ sensors could be well controlled by adjusting the number of deposition cycles for PB preparation. This work demonstrates the feasibility of self-assembled PB modified electrode in sensing application, and provides an effective approach to control the sensitivity of PB-based amperometric biosensors.     

Single microparticle applied in magnetic-switchable electrochemistry

In this work we demonstrated the micromanipulation of a single magnetic microparticle (Fe₃O₄) modified with Prussian blue (PB) for use in magnetic-switchable electrochemistry. A single Fe₃O₄-PB microparticle with 120 μm was isolated in an electrochemical microcell (20 μL), in which a fine control of PB electrochemical process on carbon electrode (Ø = 4.0 mm) was obtained. For cyclic voltammetry, redox processes attributed to PB/PW (Prussian blue/Prussian white) one electron redox couple were observed, however the capacitive currents were very high. On the other hand, by using differential pulse voltammetry, a maximum faradaic current for anodic peak of 200 nA cm^− 2 at 0.06 V was observed. Several and high stable chronoamperograms were obtained by “switch on” and “switch off” magnetic commutative states for a single microparticle, showing that the system developed here can be very promising for application in electrochemistry.     

Optical and electrical conducting properties of Polyaniline/Tin oxide nanocomposite

Polyaniline(PANI)/Tin oxide (SnO₂) hybrid nanocomposite with a diameter 20–30 nm was prepared by co-precipitation process of SnO₂ through in situ chemical polymerization of aniline using ammonium persulphate as an oxidizing agent. The resulting nanocomposite material was characterized by different techniques, such as X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infrared spectroscopy (FT-IR) and Ultraviolet–Visible spectroscopy (UV–Vis), which offered the information about the chemical structure of polymer, whereas electron microscopy images provided information regarding the morphology of the nanocomposite materials and the distribution of the metal particles in the nanocomposite material. SEM observation showed that the prepared SnO₂ nanoparticles were uniformly dispersed and highly stabilized throughout the macromolecular chain that formed a uniform metal-polymer nanocomposite material. UV–Vis absorption spectra of PANI/SnO₂ nanocomposites were studied to explore the optical behavior after doping of nanoparticles into PANI matrix. The incorporation of SnO₂ nanoparticles gives rise to the red shift of π–π¹ transition of polyaniline. Thermal stability of PANI and PANI/SnO₂ nanocomposite was investigated by thermogravimetric analysis (TGA). PANI/SnO₂ nanocomposite observed maximum conductivity (6.4 × 10^?3 scm^?1) was found 9 wt% loading of PANI in SnO₂.     

Molybdenum electrodes for hydrogen production by water electrolysis using ionic liquid electrolytes

The hydrogen production by water electrolysis was tested with different electrocatalysts (molybdenum, nickel, iron alloys containing chromium, manganese and nickel) using aqueous solutions of ionic liquid (IL) like 1-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF₄). The hydrogen evolution reaction (HER) was performed at room temperature in a potential of −1.7 V (PtQRE). A Hoffman cell apparatus was used to water electrolysis with current density values, j, between 14.6 mA cm⁻² (for Ni electrode) and 77.5 mA cm⁻² (for Mo electrode). The system efficiency was very high for all electrocatalysts tested, between 97.0% and 99.2%. The energy activation values of HER was determined in an aqueous solution of BMI.BF₄ 10 vol.%, using platinum (23.40 kJ mol⁻¹) and Mo (9.22 kJ mol⁻¹) as electrocatalysts. The results show that the hydrogen production in IL electrolyte can be carried out with cheap material at room temperature, which makes this method economically attractive.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

Nanocomposite of a chromium Prussian blue with TiO2. Redox reactions and the synthesis of Prussian blue molecule-based magnets

The reaction of [NEt₄]₃[Cr(CN)₆] with titanium(III) p-toluenesulfonate at a pH of 2 affords a gray solid whose metal content and spectroscopic and magnetic properties are fully consistent with it being a Prussian blue material of stoichiometry “Ti^III[Cr^III(CN)₆] · H₂O”. The carbon, nitrogen, and hydrogen content, however, are not consistent with this stoichiometry, and further investigation showed that the gray material has a powder X-ray diffraction profile, infrared spectrum, and magnetic properties very similar to those of the “all-chromium” Prussian blue Cr^II[Cr^III(CN)₆]_0.67 · 6H₂O. All data, including the C, H, and N weight percentages, are consistent with the conclusion that the material isolated is a nanocomposite of Cr^II[Cr^III(CN)₆]_0.67 · xH₂O and TiO₂ in the ratio of 1–1.6. These results suggest that Ti^III reduces some of the [Cr^III(CN)₆]³⁻ ions to generate Ti^IV and Cr^II; the former hydrolyzes to amorphous TiO₂ · 2H₂O, the latter loses its bound CN ligands and reacts with unreacted [Cr^III(CN)₆]³⁻ ions to generate the crystalline all-chromium PB species. The electrochemical potentials suggest that the [Cr^III(CN)₆]³⁻ ion should not be reduced by Ti^III; evidently, this unfavorable reaction is driven by the insolubility of the reaction products. The results constitute a cautionary tale in two respects: first, that the characterization of Prussian blue materials must be conducted with care and, second, that the insolubility of Prussian blue analogues can sometimes drive reactions that in solution are thermodynamically unfavorable.     

Application of carboxyl functionalized graphene oxide as mimetic peroxidase for sensitive voltammetric detection of H2O2 with 3,3′,5,5′-tetramethylbenzidine

A sensitive electrochemical method for H₂O₂ determination was proposed with carboxyl functionalized graphene oxide (GO-COOH) as mimetic peroxidase and 3,3′,5,5′-tetramethylbenzidine (TMB) as substrate. GO-COOH exhibited intrinsic peroxidase-like activity that could catalyze the oxidation of TMB with H₂O₂. The generated product exhibited a sensitive second order derivative linear sweep voltammetric reduction peak at − 0.93 V (vs. Ag/AgCl) in Britton–Robinson buffer. Under the optimal conditions the reduction peak current was proportional to H₂O₂ concentration in the linear range from 0.006 to 0.8 μmol L^− 1 with the detection limit of 1.0 nmol L^− 1 (3σ). This proposed method was further applied to determine H₂O₂ content in fresh milk samples with satisfactory results.     

Fabrication of super-macroporous nanocomposites by deposition of carbon nanotubes onto polymer cryogels

Electrically conducting super-macroporous carbon nanotube/polymer cryogel nanocomposites were fabricated by a novel approach based on deposition of carbon nanotubes (CNTs) onto the inner surface of pre-formed cryogels assisted by cryogenic treatment. Stable aqueous dispersions of multi-walled and single-walled carbon nanotubes were firstly obtained by non-covalent modification of pristine nanotubes with either pyrene containing polydimethylacrylamide or poly(ethylene oxide)₂₆-b-poly(propylene oxide)₄₀-b-poly(ethylene oxide)₂₆ copolymers and, then, exploited for the preparation of nanocomposites. The mechanical and electrical properties of nanocomposite materials were measured and compared to similar materials prepared by established method. The novel approach provided super-macroporous nanocomposites with high electrical conductivity (>10^?2 S/m) at much lower nanotube content (0.12 wt.%).     

Dual-doped graphene/perovskite bifunctional catalysts and the oxygen reduction reaction

We report the first investigation of dual-doped graphene/perovskite mixtures as catalysts for oxygen reduction. Pairwise combinations of boron, nitrogen, phosphorus and sulfur precursors were co-reduced with graphene oxide and mixed with La_0.8Sr_0.2MnO₃ (LSM) to produce SN-Gr/LSM, PN-Gr/LSM and BN-Gr/LSM catalysts. In addition, the dual-doped graphenes, graphene, LSM, and commercial Pt/C were used as controls. The addition of LSM to the dual-doped graphenes significantly improved their catalytic performance, with optimised composition ratios enabling PN-Gr/LSM to achieve 85% of the current density of commercial Pt/C at − 0.6 V (vs. Ag/AgCl) at the same loading. The effective number of electrons increased to ca. 3.8, and kinetic analysis confirms the direct 4 electron pathway is favoured over the stepwise (2e + 2e) route: the rate of peroxide production was also found to be lowered by the addition of LSM to less than 10%.     

Vibrational spectroscopic characterization of the phosphate mineral series eosphorite–childrenite–(Mn,Fe)Al(PO4)(OH)2·(H2O)

The phosphate mineral series eosphorite–childrenite–(Mn,Fe)Al(PO₄)(OH)₂·(H₂O) has been studied using a combination of electron probe analysis and vibrational spectroscopy. Eosphorite is the manganese rich mineral with lower iron content in comparison with the childrenite which has higher iron and lower manganese content. The determined formulae of the two studied minerals are: (Mn_0.72,Fe_0.13,Ca_0.01)(Al)_1.04(PO₄, OHPO₃)_1.07(OH_1.89,F_0.02)·0.94(H₂O) for SAA-090 and (Fe_0.49,Mn_0.35,Mg_0.06,Ca_0.04)(Al)_1.03(PO₄, OHPO₃)_1.05(OH)_1.90·0.95(H₂O) for SAA-072. Raman spectroscopy enabled the observation of bands at 970 cm⁻¹ and 1011 cm⁻¹ assigned to monohydrogen phosphate, phosphate and dihydrogen phosphate units. Differences are observed in the area of the peaks between the two eosphorite minerals. Raman bands at 562 cm⁻¹, 595 cm⁻¹, and 608 cm⁻¹ are assigned to the ν₄ bending modes of the PO₄, HPO₄ and H₂PO₄ units; Raman bands at 405 cm⁻¹, 427 cm⁻¹ and 466 cm⁻¹ are attributed to the ν₂ modes of these units. Raman bands of the hydroxyl and water stretching modes are observed. Vibrational spectroscopy enabled details of the molecular structure of the eosphorite mineral series to be determined.     

Self-assembled Nafion–silica nanoparticles for elevated-high temperature polymer electrolyte membrane fuel cells

In this paper, a novel Nafion/SiO₂ nanocomposite membrane based on the self-assembled Nafion–SiO₂ nanoparticles was developed. The average particle size of Nafion–SiO₂ nanoparticles prepared by self-assembly process was 2.8 ± 0.5 nm. The self-assembled Nafion–SiO₂ nanoparticles significantly enhance the durability of the Nafion/silica nanocomposite membrane as compared to that of conventional Nafion/silica composite and Nafion 212 membranes under wet/dry cyclic tests at 90 °C. With an addition of 5 wt% self-assembled Nafion–SiO₂ nanoparticles, the Nafion/SiO₂ nanocomposite membrane shows a significantly improved performance stability at cell/humidifying temperatures of 100 °C/60 °C under a current density of 600 mA/cm², and the degradation rate is 0.12 mV/min, almost 20 times lower than 2.33 mV/min measured on the pristine Nafion 212 membrane under the same conditions. The present results demonstrate the promises of the self-assembled Nafion/SiO₂ nanocomposite membrane for elevated-high temperature PEM fuel cells applications.     

On the stability and properties of the polyacrylate/Na-MMT nanocomposite obtained by seeded emulsion polymerization

For high performance waterborne coatings usually polymer latexes with low emulsifier content are more preferred. Although polymer/clay nanocomposites offer improved properties, it is difficult to produce clay based nanocomposite latexes containing low emulsifier due to the stabilization problems especially caused by organoclays. Present study deals with the preparation of a tBA/BA/MAA ternary copolymer/clay nanocomposite containing 3 wt.% sodium montmorillonite (Na⁺-MMT) via seeded emulsion polymerization. Experimentally it was observed that even the usage of hydrophilic clay caused stabilization problem and a certain amount of emulsifier (>1 wt.%) was necessary to obtain stable latexes. In addition, the usage of a low molecular weight water soluble polymer as steric barrier was found to increase the stability of system. Obtained nanocomposite latex showed fine particle size diameter (127 nm) and very narrow size distribution (PDI = 0.06). The WAXD and TEM investigations indicated that a mostly exfoliated nanocomposite was obtained. Thermal analyses (DSC, DMTA and TGA) showed that there was no change at T_g of the copolymer while very high improvement was obtained for elastic modulus and a slight increase in thermal stability. According to the rheological measurements, the nanocomposite latex showed a higher low shear viscosity, a stronger shear thinning behavior and an improved physical stability in comparison to the reference latex.     

Application of modified multiwalled carbon nanotubes as solid sorbent for separation and preconcentration of trace amounts of manganese ions

In this work, the potential of modified multiwalled carbon nanotubes for separation and preconcentration of trace amounts of manganese ion is studied. Multiwalled carbon nanotubes were oxidized with concentrated HNO₃ and then modified with loading 1-(2-pyridylazo)-2-naphtol. Mn(II) ions could be quantitatively retained by modified multiwalled carbon nanotubes in the pH range of 8–9.5. Elution of the adsorbed manganese was carried out with 5.0 mL of 0.1 mol L^?1 HNO₃. Detection limit is 0.058 ng mL^?1 and analytical curve is linear in the range of 0.1 ng mL^?1–5.0 μg mL^?1 in the initial solution with a correlation coefficient 0.9977 and the preconcentration factor is 100. Relative standard deviation for eight replicate determination of 0.5 μg mL^?1 of manganese in the final solution is 0.41%. The effects of the experimental parameters, including the sample pH, flow rates of sample and eluent solution, eluent type, breakthrough volume and interference ions, were studied for preconcentration of Mn(II) ions in detail to optimize the conditions. The method was successfully applied for separation, preconcentration and determination of manganese in different samples.     

Enhanced supercapacitive behaviors of birnessite

The birnessite type manganese dioxide electrode was prepared by the electrochemical stimulation as we recently described. It showed 190 F g⁻¹ in a Na₂SO₄ aqueous solution between −0.1 and 0.9 V versus Ag/AgCl at 1 A g⁻¹. The specific capacitance of birnessite was decreased by the manganese dissolution when the reduction and oxidation were repeated. By adding small amounts of Na₂HPO₄ or NaHCO₃ into the electrolyte, the capacitance increased to 200–230 F g⁻¹ and the manganese dissolution was successfully suppressed. Thanks to the additives, the birnessite demonstrated the much improved cycleability over >1800 cycles.     

Comparison of performances of bioanodes modified with graphene oxide and graphene–platinum hybrid nanoparticles

The performances of graphene oxide (GO) and graphene–platinum hybrid nanoparticles (Gr-Pt hybrid NPs) were compared for biofuel cell (BFC) systems. This is the first study that constitutes these nanomaterials in BFC systems. For this purpose, fabricated bioanodes were combined with laccase modified biocathode in a single cell membraneless BFC. Power and current densities of these systems were calculated as 2.40 μW cm^− 2 and 211.90 μA cm^− 2 for GO based BFC and 4.88 μW cm^− 2 and 246.82 μA cm^− 2, for Gr-Pt hybrid NPs based BFC. As a result, a pioneer study which demonstrates the effective performances of combination of graphene with Pt was conducted.