Remarkable carbon dioxide catalytic capture (CDCC) leading to solid-form carbon material via a new CVD integrated process (CVD-IP): An alternative route for CO2 sequestration

Through our newly-developed “chemical vapor deposition integrated process (CVD-IP)” using carbon dioxide (CO₂) as the raw material and only carbon source introduced, CO₂ could be catalytically activated and converted to a new solid-form product, i.e., carbon nanotubes (CO₂-derived) at a quite high yield (the single-pass carbon yield in the solid-form carbon-product produced from CO₂ catalytic capture and conversion was more than 30% at a single-pass carbon-base). For comparison, when only pure carbon dioxide was introduced using the conventional CVD method without integrated process, no solid-form carbon-material product could be formed. In the addition of saturated steam at room temperature in the feed for CVD, there were much more end-opening carbon nano-tubes produced, at a slightly higher carbon yield. These inspiring works opened a remarkable and alternative new approach for carbon dioxide catalytic capture to solid-form product, comparing with that of CO₂ sequestration (CCS) or CO₂ mineralization (solidification), etc. As a result, there was much less body volume and almost no greenhouse effect for this solid-form carbon-material than those of primitive carbon dioxide.     

Chemically modified activated carbon with S-benzyldithiocarbazate as a new solid-phase extractant for preconcentration of mercury prior to ICP-AES determination

A new sorbent S-benzyldithiocarbazate (SBDTC) modified activated carbon (AC-SBDTC) was prepared and studied for preconcentration for trace mercury(II) prior to inductively coupled plasma atom emission spectrometry (ICP-AES). The experimental conditions were optimised with respect to different experimental parameters using both batch and column procedures in detail. The optimum pH value for the separation of Hg(II) on the new sorbent was 3, while the adsorption equilibrium was achieved in less than 5?min. Complete elution of the adsorbed metal ions from the sorbent surface was carried out using 5?mL of 0.25?mol?L^?1 of HCl and 2% CS(NH₂)₂. Common coexisting ions did not interfere with the determination. The maximum static adsorption capacity of the sorbent under optimum conditions was found to be 0.55?mmol?g^?1. The detection limit of the present method was found to be 0.09?ng?mL^?1, and the relative standard deviation (RSD) was lower than 2.0%. The procedure was validated by analysing the certified reference river sediment material (GBW 08301, China), the results obtained were in good agreement with standard values. This sorbent was successfully employed in the separation and preconcentration of trace Hg(II) from the natural water samples yielding 80-fold concentration factor.     

Beam-injection flame furnace AAS: comparison of different nozzle types for beam generation and application of sub-critical liquid carbon dioxide as carrier and gas pressure pump

In beam injection flame furnace AAS (BIFF-AAS) the sample is introduced as a free-flying high-speed liquid beam into an AAS flame-heated nickel tube, resulting in a considerable improvement in the power of detection. For optimization of beam generation different nozzle types (smooth jet nozzles, turbulent working nozzles) have been compared at different pressures. It was found that the type of the nozzle hardly influences the analytical signal. However, the flow rates resulting from the different inner diameters of the nozzles and the applied pressures led to drastic changes in the analytical signal. For these investigations a recently developed 0.6 MPa (84 psig) diaphragm pump system was used. Furthermore, for the first time ever sub-critical liquid carbon dioxide has been used simultaneously as a liquid gas-pressure pump, as carrier in a flow-injection system (FIA), and for the beam generation. Transport of the carrier takes place as a result of the head pressure (6 MPa) of the liquid CO₂ in the gas cylinder. For volatile elements (e.g. Cd, Hg, Pb, and Tl) detection limits between 0.2 µg L^–1 (Cd) and 28 µg L^–1 (Hg) were found, the standard deviation was from 0.6% to 3.2% depending on the element, concentration, and sample volume used. The use of liquid CO₂ as a carrier in FIA systems opens up new possibilities for online sample pretreatment and trace preconcentration.     

Raman spectroscopy as a tool for the analysis of carbon-based materials (highly oriented pyrolitic graphite,multilayer graphene and multiwall carbon nanotubes) and of some of their elastomeric composites

Raman spectra of highly oriented pyrolitic graphite, multilayer graphene and multiwall carbon nanotubes are carried out at different laser powers and different excitation energies. The effects of the laser heating and the double resonance Raman scattering are investigated as a prerequisite for a correct interpretation of the Raman spectra of carbon materials-based composites. The Raman spectra of multilayer graphene and multiwall carbon nanotubes embedded in a silicone matrix are also analyzed in an attempt to get some insights into the polymer–filler interface.     

Study of carbon nanotubes and functionalized-carbon nanotubes as substrates for flow injection solid phase extraction associated to inductively coupled plasma with ultrasonic nebulization: Application to Cd monitoring in solid environmental samples

A research was performed to evaluate the capabilities of carbon nanotubes (CNTs) and modified CNTs to serve as sorbents for preconcentrating Cd together with on-line ultrasonic nebulization (USN)-inductively coupled plasma optical emission spectrometry (ICPOES). Three different carbon nanotubes sustrates namely, carbon nanotubes (CNTs), oxidized-carbon nanotubes (ox-CNTs) and l-alanine-carbon nanotubes (ala-CNTs) were studied systematically and the main factors influencing the preconcentration and determination of Cd were examined thoroughly. The CNTs evaluated showed dissimilar adsorption behaviors leading to increasing preconcentration factors when used in the proposed on-line solid phase extraction (SPE) system as follows: CNT < ala-CNT < ox-CNT. Aiming to achieve the best analytical performance, ox-CNTs were used as they enable quantitative retention of Cd at pH 7.0 and instantaneous elution of the analyte with 10% HNO₃. Under optimal conditions, the adsorption capacity on ox-CNTs was found to be 130 μmol g^?1 and the detection limit (3σ) achieved was 1.03 μg L^? 1. The precision of the method expressed as the relative standard deviation (RSD) turned to be 3.0%. The flow injection method involving use of ox-CNTs as sorbent and USN-ICPOES for detection was successfully applied to the determination of Cd in different kinds of environmental samples.     

8-Aminoquinoline as a new bidentate ligand for cis-MoO2: synthesis and characterization of a dioxomolybdenum(VI) amide [MoO2(NHC9H6N)2]

The reaction of (Bu₄N)₂[Mo₆O₁₉] with 8-aminoquinoline in the presence of DCC (N,N′-dicyclohexylcarbodiimide) afforded the cis-dioxo-Mo(VI) amide [MoO₂(NHC₉H₆N)₂], which was characterized by spectroscopy, mass spectrometry, ¹H NMR, and single-crystal X-ray analysis. X-ray crystallography shows that the complex exhibits a distorted octahedral geometry with each oxo ligand trans to the quinolyl nitrogen and the amido ligands are bound to the metal in an N,N-chelating fashion. The molecules form zigzag chains via C–H?···?O hydrogen bonds and the chains are connected into networks through interchain N–H?···?O hydrogen bonds.     

Evaluation of a novel PTFE material for use as a means for separation and preconcentration of trace levels of metal ions in sequential injection (SI) and sequential injection lab-on-valve (SI-LOV) systems: Determination of cadmium(II) with detection by electrothermal atomic absorption spectrometry (ETAAS)

The operational characteristics of a novel poly(tetrafluoroethylene) (PTFE) bead material, granular Algoflon^®, used for separation and preconcentration of metal ions via adsorption of on-line generated non-charged metal complexes, were evaluated in a sequential injection (SI) system furnished with an external packed column and in a sequential injection lab-on-valve (SI-LOV) system. Employed for the determination of cadmium(II), complexed with diethyldithiophosphate (DDPA), and detection by electrothermal atomic absorption spectrometry (ETAAS), its performance was compared to that of a previously used material, Aldrich PTFE, which had demonstrated that PTFE was the most promising for solid-state pretreatments. By comparing the two materials, the Algoflon^® beads exhibited much higher sensitivity (1.6107 μg l⁻¹ versus 0.2956 μg l⁻¹ per integrated absorbance (s)), and better retention efficiency (82% versus 74%) and enrichment factor (20.8 versus 17.2), although a slightly smaller linear dynamic range (0.05-0.25 μg l⁻¹ versus 0.05-1.00 μg l⁻¹). Moreover, no flow resistance was encountered under the experimental conditions used. The results obtained on three standard reference materials were in good agreement with the certified values.     

QCMS2 as a new method for providing insight into peptide fragmentation: The influence of the side‐chain and inter–side‐chain interactions

The identification of peptides and proteins from tandem mass spectra is a difficult task and multiple tools have been developed to aid this identification. We present a new method called quantum chemical mass spectrometry for materials science (QCMS²), which is based on quantum chemical calculations of bond orders, reaction, and transition‐state energies at the DFT/B3LYP/6‐311+G* level of theory. The method was used to describe the fragmentation pathways of five X‐His‐Ser tripeptides with X = Asn, Asp, Glu, Ser, and Trp, thereby focusing on the influence of the side chain and inter–side‐chain interactions on the fragmentation. The main features in the mass spectra of the five tripeptides were correctly reproduced, and a number of fragments were assigned to fragmentations involving the side chain and the influence of inter–side‐chain interactions. Product ion spectra were recorded to evaluate the capabilities and limitations of QCMS² and a number of conventional tools.     

Phosphorylated PEG (PPEG) as a new support for generation of nano‐Pd(0): application to the Heck–Mizoroki and Suzuki–Miyaura coupling reactions

Polyethylene glycols (PEGs) with different molecular weights (M_w = 200, 400, 1000) were phosphorylated to their bis‐diphenyl phosphinite derivatives as stable solids which are melted in the range 140–160°C. These phosphorylated PEGs were used as ligands and reducing agents to generate nano‐Pd(0) catalysts in 2.5–8.3 nm. The nano‐Pd(0) particles supported on phosphorylated PEG₂₀₀ were applied for the efficient Heck–Mizoroki carbon–carbon coupling reactions of ArX (X = Cl, Br, I) at 80–100°C under solvent‐free conditions and for the Suzuki–Miyaura coupling reaction in ethanol at 70°C. The catalyst was recycled easily and reused for several runs. Copyright © 2013 John Wiley & Sons, Ltd.