Crystallization kinetics of a-Se75Te25 − xGax (x = 0, 5, 10 and 15 at wt %) glassy system

Bulk glasses of a-Se₇₅Te_25 ? xGa_x (x = 0, 5, 10 and 15 at wt %) have been prepared by melt quenching technique. These samples were structurally characterized by using X-ray diffraction. Kinetic of crystallization in these glasses was studied under non-isothermal conditions using differential thermal analysis (DTA). DTA is performed at different heating rates of 5, 10, 15, 20 and 30 °C/min. The values of glass transition (T_g) and crystallization peak temperature (T_p) are found to be composition and heating-rate dependent. The obtained results have been analyzed in terms of activation energy of glass transition (E_g) using Kissinger's and Mahadevan et al. relations. Values of E_g obtained by the two relations are in agreement with each other. The results indicate that the crystallization process is a three-dimensional growth.     

Structure and crystallization behavior of mixed potassium-lithium niobiosilicate glasses

Potassium-lithium niobiosilicate (KLiNS) glasses with a composition of (27 ? x)K₂O · xLi₂O · 27Nb₂O₅ · 46SiO₂ (x = 0, 3, 12 and 20) have been synthesized by a melt-quenching method. The glass structure and devitrification behavior have been studied by Raman spectroscopy, DTA, and XRD. By increasing the lithium content, less distorted niobium octahedra increase, indicating a niobium clustering. This change strongly affects the crystallization behavior. In the glasses x = 0 and x = 3, just above T_g, only nanocrystals of an unidentified phase are formed, while for x = 12 and x = 20 potassium lithium niobate (KLN) solid solutions with tetragonal tungsten–bronze structure crystallize by bulk nucleation. In these glasses, LiNbO₃ crystallizes at higher temperature by surface nuclei. Ultimately, it is possible to produce nanostructured glasses based on KLN nanocrystals, by partial replacement of K by Li.     

Thermal and optical properties of TeO2–ZnO–BaO glasses

We report the results of a systematic study of the thermal and optical properties of a new family of tellurite glasses, TeO₂–ZnO–BaO (TZBa), as a function of the barium oxide mole fraction and compare them with those of TeO₂–ZnO–Na₂O (TZN). The characteristic temperatures of this new glass family (glass transition, T_g, crystallization, T_x, and melting, T_m) increase significantly with BaO content and the glasses are more thermally stable (greater ΔT = T_x ? T_g) than TZN glasses. Relative to these, Raman gain coefficient of the TZBa glasses also increases by approximately 40% as well as the Raman shift from ~ 680 cm^? 1 to ~ 770 cm^? 1. The latter shift is due to the modification of the glass with the creation of non-bridging oxygen ions in the glass network. Raman spectroscopy allows us to monitor the changes in the glass network resulting from the introduction of BaO.     

Effects of microalloying with 3d transition metals on glass formation in AlYFe alloys

The effects of microalloying on glass formation and stability were systematically investigated by substituting 0.5 at.% of all 3d transition metals for Al in Al₈₈Y₇Fe₅ alloys. X-ray diffraction and isothermal differential scanning calorimetry studies indicate that samples containing microadditions of Ti, V, Cr, Mn, Fe and Co were amorphous, while those alloyed with Ni and Cu were not. The onset temperatures for crystallization (devitrification) of the amorphous alloys were increased with microalloying and some showed a supercooled liquid region (ΔT_x = T_x − T_g) of up to 40 °C. In addition, microalloying changes the glass structure and the devitrification sequence, as determined by differential scanning calorimetry (DSC), X-ray diffraction (XRD), transmission electron microscopy (TEM), differential thermal analysis (DTA) and high energy X-ray diffraction. The results presented here suggest that the order induced in the alloy by the transition metal microaddition decreases the atomic mobility in the glass and raises the barrier for the nucleation of α-Al, the primary devitrifying phase in most cases. New intermetallic phases also appear with microalloying and vary for different transition metal additions.     

The preparation and structural studies in the (80 − x)TeO2–20ZnO–(x)Er2O3 glass system

Er³⁺-doped tellurite glasses of the (80 ? x)TeO₂–20ZnO–(x)Er₂O₃ system (0.5 mol% ? x ? 2.5 mol%) have successfully been made by melt-quenching technique and their structure has been investigated by means of DTA and Raman spectroscopy. The DTA results show the thermal parameters; such as the glass transition temperature (T_g) and crystallization temperature (T_c) were determined. It is found that this system provides a stable and wide glass formation range in which the glass stability around 99–140 °C may be obtained. The Raman spectroscopy used the structural studies in the glass system. Two Raman shift peaks were observed around 640–670 cm^?1 and 720–740 cm^?1, which correspond to the stretching vibration mode of TeO₄ tbp and TeO₃ tp, respectively. It is found that the spectral shift in Raman spectra is depending on the Er₂O₃ content. This evolution is an indication of the changes in the basic unit of the glass structure.     

A composition dependent thermal behavior of GexSe35−xTe65 glasses

Alternating differential scanning calorimetric (ADSC) studies have been performed to understand the thermal behavior of bulk Ge_xSe_35?xTe₆₅ glasses (17 ? x ? 25); it is found that the glasses with x ? 20 exhibit two crystallization exotherms (T_c1 & T_c2). On the other hand, those with x ? 20.5, show a single crystallization reaction upon heating. The exothermic reaction at T_c1 has been found to correspond to the partial crystallization of the glass into hexagonal Te and the reaction at T_c2 is associated with the additional crystallization of rhombohedral GeTe phase. The glass transition temperature of Ge_xSe_35?xTe₆₅ glasses is found to show a linear but not-steep increase, indicating a progressive, but a gradual increase in network connectivity with Ge addition. It is also found that T_c1 of Ge_xSe_35?xTe₆₅ glasses with x ? 20, increases progressively with Ge content and eventually merges with T_c2 at x ≈ 20.5 (〈r〉 = 2.41); this behavior has been understood on the basis of the reduction in TeTe bonds of lower energy and increase in GeTe bonds of higher energy, with increasing Ge content. Apart from the interesting composition dependent crystallization, an anomalous melting behavior is also exhibited by the Ge_xSe_35?xTe₆₅ glasses.     

Stability of Ni-based bulk metallic glasses

Several ternary (Ni_xNb_ySn_z) refractory alloy glasses (RAGs) were studied at elevated temperatures in order to assess the stability of the amorphous state, i.e. devitrification, and to identify subsequent phase transformations in these materials. differential scanning calorimetry (DSC) experiments indicated a complex phase transformation sequence with several distinct crystallization and melting events being recorded above the glass transition temperature, T_g. Below T_g the RAG samples were studied with an in situ environmental X-ray furnace facility, which allowed step-wise isothermal ramping experiments commencing at a temperature below the reduced temperature of T/T_g ≈ 0.80. Distinct crystalline phases were observed when T/T_g ≈ 0.84 for ternary RAG alloys, while similar experiments on Zr-based Vit 106 glass alloys did not reveal any apparent phase separation until T/T_g ≈ 0.96. The phase separation kinetics followed an Arrhenius type of relationship with Ni₃Sn, and Nb₂O₅ being the principle crystalline precipitates.     

Electrical properties of SrBi2(Nb0.7V0.3)2O9−δ in the SrO–Bi2O3–0.7Nb2O5–0.3V2O5–Li2B4O7 glass system

Glasses in the system (100 − x)Li₂B₄O₇–x(SrO–Bi₂O₃–0.7Nb₂O₅–0.3V₂O₅) (where x = 10, 30 and 50, in molar ratio) were fabricated via melt quenching technique. The compositional dependence of the glass transition (T_g) and crystallization (T_cr) temperatures was determined by differential thermal analysis. The as-quenched glasses on heat-treatment at 783 K for 6 h yielded monophasic crystalline strontium bismuth niobate doped with vanadium (SrBi₂(Nb_0.7V_0.3)₂O_9−δ (SBVN)) in lithium borate (Li₂B₄O₇ (LBO)) glass matrix. The formation of nanocrystalline layered perovskite SBVN phase was preceded by the fluorite phase as established by both the X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The dielectric constants for both the as-quenched glass and glass–nanocrystal composite increased with increasing temperature in the 300–873 K range, exhibiting a maximum in the vicinity of the crystallization temperature of the host glass matrix. The electrical behavior of the glasses and glass–nanocrystal composites was characterized using impedance spectroscopy.     

Glasses in the SbPO4–WO3 system

Glasses in the binary system (100 − x)SbPO₄–xWO₃ (20 ⩽ x ⩽ 60, x in mol%) have been prepared and characterized. Differential thermal analysis (DTA) shows that the glass transition temperature, T_g, increases from 412 °C, for samples containing 20 mol% of WO₃, to 481 °C observed for glass containing 60 mol%. Sample containing 40 mol% in WO₃ were observed to be the most stable against devitrification. The structural organization of the glasses has been studied by using Fourier transform infra-red (FTIR), Raman, ³¹P Magic angle spinning (MAS) and spin echo nuclear magnetic resonance (NMR) spectroscopies. Results suggest two distinct networks comprising the glass structure, one with high SbPO₄ content and the other characteristic of the highest WO₃ content samples. The glasses present photochromic properties. Colour changes are observed for samples after exposure to ultraviolet or visible laser light. XANES, at L₁ absorption edge of tungsten, suggests partial reduction from W⁶⁺ to W⁵⁺ species during the laser irradiation. The photochromic effects and the colour changes, promoted by laser excitation, are reversible and easily removed by heat for during 1 h at 150 °C. Subsequent ‘write/erase’ cycles can be done without degradation of the glasses.     

Crystallization kinetic studies on Bi1.75Pb0.25Sr2Ca2Cu3-xSnxOδ glass-ceramic by using non-isothermal technique

The Sn substituted Bi_1.75Pb_0.25Sr₂Ca₂Cu_3-xSnxO_δ glass ceramic (where x = 0, 0.1, 0.3, and 0.5) samples were prepared by the melt-quenching method. Crystallization kinetic studies of the samples were conducted using the differential thermal analysis (DTA). The oxidation behavior of the samples was also analyzed using the thermogravimetry analysis (TG). The DTA curves were registered with different heating rates (5, 10, 15, and 20 Kmin^? 1) up to 1200 ± 0.5 K. The crystallization results were analyzed, and activation energy of crystallization process as well as the crystallization mechanisms and the effect of Sn substitution on powder glass ceramic were characterized. The glass transition temperature (T_g), the first crystallization peak temperature (T_x1) and the second crystallization peak temperature (T_x2) values were obtained as 713.0 ± 0.5–746.6 ± 0.5, 731.0 ± 0.5–760.8 ± 0.5 and 789.0 ± 0.5–820.1 ± 0.5 K, respectively. The activation energy (E_a) of crystallization was estimated from DTA results to be about 332.8 ± 0.1, 358.0 ± 0.1, 353.1 ± 0.1 and 348.9 ± 0.1 kJ/mol for x = 0, 0.1, 0.3 and 0.5, respectively, by using the Kissinger method. The Avrami parameter (n) values calculated at different Sn ratio from DTA results were found to be between 1.70 ± 0.01 and 2.57 ± 0.01, results reflect the growth of small particle with a decreasing nucleation rate.     

Influence of europium ions on structure and crystallization properties of bismuth borate glasses and glass ceramics

Glasses of the xEu₂O₃ · (100?x)[2Bi₂O₃ · B₂O₃] system with 0 ? x ? 25 mol% have been characterized by X-ray diffraction and FTIR spectroscopy measurements. Melting at 1100 °C and the rapid cooling at room temperature permitted us to obtain glass samples. In order to improve the local order and to develop crystalline phases, the glass samples were kept at 625 °C for 24 h. After heat treatment two crystalline phases were put into evidence. One of the crystalline phases was observed for the host glass matrix, the x = 0 mol% sample, and belongs to the cubic system. The second one was observed for the x = 25 mol% sample and was find to be orthorhombic with two unit cell parameters very close to each other. For the samples with 0 < x < 25 mol% there is a mixture of the two mentioned phases. FTIR spectroscopy data suggest that both Bi₂O₃ and B₂O₃ play the glass network former role while the europium ions play the network modifier role in the studied glasses.     

Effect of devitrification on ion motion in lithium-disilicate glass

Li-disilicate glass-ceramics consist of microcrystallites imbedded in the glassy Li₂O · 2SiO₂ matrix where the number and size of the crystallites depend on the devitrification heat treatment. To assess ion motion in these model glass-ceramics, we have measured the temperature dependence of the dc conductivity, σ_dc, and the ⁷Li nuclear spin relaxation (NSR) rate, 1/T₁, in samples with various crystalline fraction, c, ranging from c = 0 (pure glass) to c = 1 (fully devitrified polycrystalline ceramic). The Cole–Cole presentation of the complex impedance shows two separate arcs caused by the remarkable difference of the ionic motion in the glassy and crystalline phase. These two arcs correspond to a bi-exponential decay of the ⁷Li nuclear spin magnetization where the resulting two NSR rates are induced by the ionic motion in the two phases. Thus the NSR and σ_dc data provide a comprehensive picture of the ionic motion in the glassy and crystalline phases. In particular, the ionic motion is the fastest in the glass; then at lower values of c we observe a metastable crystalline phase with ionic motion much greater than in the stable (LS₂) crystalline phase existing at large c-values.     

Kerr studies of several tellurite glasses

Estimates of Kerr electrooptical sensitivity of several tellurite glasses are presented. The highest value of Kerr coefficient B ～ 190 × 10^?16 m V^?2 is registered for 0.6TeO₂–0.3TlO_0.5–0.1ZnO glass. This evidences the prospects of thallium–tellurite glass system for electrooptical applications. A gradual decrease of B from 41 × 10^?16 to 26 × 10^?16 m V^?2 in (1 ? x) TeO₂ – xNbO_2.5 system is revealed for x increasing from 0.1 to 0.15. No crystalline phase was found in that system, thus allowing attributing its Kerr sensitivity to the intrinsic properties of the glass matrix. The Kerr coefficient variation from 66 to 81 × 10^?16 m V^?2 was observed for 0.85TeO₂–0.15WO₃ glasses co-doped with small amounts of silver and cerium. The analysis of optical absorption spectra of several silver-containing tellurium–tungsten oxide glasses makes it possible to think that introducing cerium provokes formation of new mid-range orderings.     

Preparation of TiO2–Na2O glass by sol–gel method and structural characterization

The applicability of sol–gel process in glass formation of binary system, (100 − x)TiO₂–xNa₂O (x = 10, 20, 30), was investigated and the glasses were prepared successfully by the sol–gel process for the first time. The process of glass formation was checked by using X-ray diffraction measurement and DTA–TG analysis. In the baking step, a DTA peak related to the crystallization of gel was found. The short-range structure of glassified samples was studied by neutron scattering measurement. It is found from the results of neutron scattering measurement that the coordination number of O atom around Ti atom is about 4, and the O atoms around Ti atom form a planer square rather than a regular tetrahedron.     

Synthesis and characterization of M2O–MgO–WO3–P2O5 (M = K, Rb, Cs) glass system

Transparent glasses of the composition M₂O–MgO–WO₃–P₂O₅ (M = K, Rb, Cs), corresponding to the crystalline phases of M₂MgWO₂(PO₄)₂, have been prepared and studied by Raman and IR spectroscopy as well as DTA. Moreover, the thermally stimulated depolarization and dc conductivity have been measured. The glass transition temperature is 797, 795 and 773 K for the K-, Rb- and Cs-containing glass, respectively. Raman and IR studies have shown that these glasses have very similar structure. The main building blocks are pyrophosphate groups, WO₆ octahedra and magnesium–oxygen polyhedra. The dc conduction in these glasses is controlled by hopping of small polarons. The potassium containing glass was shown to be very stable whereas the rubidium and cesium glasses have significantly higher tendency for crystallization and phase separation. It seems, therefore, that the potassium containing glass is a suitable material for the preparation of samples containing non-linear and ferroelectric nanocrystals of the K₂MgWO₂(PO₄)₂ phosphate.     

Crystallization of bismuth oxide nano-crystallites in a SiO2–PbO–Bi2O3 glass matrix

SiO₂–PbO–Bi₂O₃ glasses having the composition of 35SiO₂–xPbO–(65 ? x)Bi₂O₃ (where x = 5, 20 and 45; in mol%) have been prepared using the conventional melting and annealing method. Differential scanning calorimetry (DSC) was employed to characterize the thermal behavior of the prepared glasses in order to determine their crystallization temperatures (T_cr). It has been found that T_cr decreases with the decrease of Bi₂O₃ content. The amorphous nature of the prepared glasses as well as the crystallinity of the produced glass–ceramics were confirmed by X-ray powder diffraction (XRD) analysis. SiPbBi₂O₆ glass nano-composites, comprising bismuth oxides nano-crystallites, were obtained by controlled heat-treatment of the glasses at their (T_cr) for 10 h. Transmission electron microscopy (TEM) of the glass nano-crystal composites demonstrates the presence of cubic Bi₂O₃ nano-crystallites in the SiPbBi₂O₆ glass matrix. Nano-crystallites mean size has been determined from XRD line width analysis using Scherrer's equation as well as from TEM; and the sizes obtained from both analyses are in good agreement. These sizes varied from about 15 to 170 nm depending on the chemical compositions of parent glasses and, consequently, their structure. Interestingly, replacement of the Bi₂O₃ by PbO in the glass compositions has pronounced effect on the nature, morphology and size of the formed nano-crystallites. Decrease of the Bi₂O₃ content increases the size of the nano-crystallites, and at the lowest Bi₂O₃ extreme, namely 20 mol%, introduces minority of the monoclinic Bi₂O₄ in addition to the cubic Bi₂O₃. The crystallization mechanism is suggested to involve a diffusion controlled growth of the bismuth oxide nano-crystallites in the SiPbBi₂O₆ glass matrix with the zero nucleation rate.     

Characterization of B2O3 and/or WO3 containing tellurite glasses

Characterization of B₂O₃ and/or WO₃ containing tellurite glasses was realized in the 0.80TeO₂–(0.20 ? x)WO₃ ? xB₂O₃ system (0 ≤ x ≤ 0.20 in molar ratio) by using differential scanning calorimetry, Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and energy dispersive X-ray spectrometry techniques. Glasses were prepared with a conventional melt-quenching technique at 750 °C. To recognize the thermal behavior of the glasses, glass transition and crystallization temperatures, glass stability value, glass transition activation energy, fragility parameter were calculated from the thermal analyses. Density, molar volume, oxygen molar volume and oxygen packing density values were determined to investigate the physical properties of glasses. Fourier transform infrared spectra were interpreted in terms of the structural transformations on the glass network, according to the changing B₂O₃ and/or WO₃ content. Crystallization behavior of the glasses was investigated by in situ X-ray diffraction measurements and microstructural characterization was realized by scanning electron microscopy and energy dispersive X-ray spectrometry analyses.     

Influence of composition in the crystallization process of Fe75−xNb10B15+x metallic glasses

The devitrification process of Fe_75−xNb₁₀B_15+x (x = 0, 5, 10) metallic glasses produced by melt-spinning has been analyzed by calorimetric, microstructural and magnetic measurements. The experimental results show large differences in the behavior of these alloys as a function of composition. The alloy x = 0 undergoes a primary crystallization process separated in two stages while only one is observed for alloys with x = 5 and x = 10. This difference, observed by DSC, is correlated with a microstructural change in the phases that precipitate. For alloys x = 5 and 10, Fe₂₃B₆ and bcc-Fe are identified after the first calorimetric peak. In the sample x = 0, bcc-Fe and an unidentified phase precipitate in the first peak but massive crystallization of bcc-Fe is observed after the second stage. Finally the thermal dependence of magnetization has been measured and the Curie temperatures for the metallic glasses are determined. The change of these quantities with heat treatment and composition is discussed.     

Studies of lead–iron phosphate glasses by Raman,Mössbauer and impedance spectroscopy

The effect of Fe₂O₃ content on electrical conductivity and glass stability against crystallization in the system PbO–Fe₂O₃–P₂O₅ has been investigated using Raman, XRD, Mössbauer and impedance spectroscopy. Glasses of the molar composition (43.3 − x)PbO–(13.7 + x)Fe₂O₃–43P₂O₅ (0 ⩽ x ⩽ 30), were prepared by quenching melts in the air. With increasing Fe₂O₃ content and molar O/P ratio there is corresponding reduction in the length of phosphate units and an increase in the Fe(II) ion concentration, which causes a higher tendency for crystallization. Raman spectra of the glasses show that the interaction between Fe sites, which is essential for electron hopping, strongly depends on the cross-linking of the glass network. The electronic conduction of these glasses depends not only on the Fe(II)/Fe_tot ratio, but also on easy pathways for electron hopping in a non-disrupted pyrophosphate network. The Raman spectra of crystallized glasses indicate a much lower degree of cross-linking since more non-bridging oxygen atoms are present in the network. Despite the significant increase in the Fe₂O₃ content and Fe(II) ion concentration, there is a considerable weakening in the interactions between Fe sites in crystalline glasses. The impedance spectra reveal a decrease in conductivity, caused by poorly defined conduction pathways, which are result of the disruption and inhomogeneity of the crystalline phases that are formed during melting.     

Network topological thresholds in gallium doped As–Te glasses – Electrical and thermal investigations

Electrical switching and differential scanning calorimetric studies are undertaken on bulk As₂₀Te_80−xGa_x glasses, to elucidate the network topological thresholds. It is found that these glasses exhibit a single glass transition (T_g) and two crystallization reactions (T_c1 & T_c2) upon heating. It is also found that there is only a marginal change in T_g with the addition of up to about 10% of Ga; around this composition an increase is seen in T_g which culminates in a local maximum around x = 15. The decrease exhibited in T_g beyond this composition, leads to a local minimum at x = 17.5. Further, the As₂₀Te_80−xGa_x glasses are found to exhibit memory type electrical switching. The switching voltages (V_T) increase with the increase in gallium content and a local maximum is seen in V_T around x = 15. V_T is found to decrease with x thereafter, exhibiting a local minimum around x = 17.5. The composition dependence of T_c1 is found to be very similar to that of V_T of As₂₀Te_80−xGa_x glasses. Based on the present results, it is proposed that the composition x = 15 and x = 17.5 correspond to the rigidity percolation and chemical thresholds, respectively, of As₂₀Te_80−xGa_x glasses.