Synthesis,crystal structure and thermal behaviour of [La(hfa)3(Phen)2] (hfa = hexafluoroacetylacetonate,Phen = o-phenanthroline)

The mixed ligand complex [La(hfa)₃(Phen)₂] (I) was obtained by the interaction of La(hfa)₃ and Phen; its composition does not depend on the stoichiometry of the reagents. According to the X-ray single crystal analysis data, complex I crystallizes in the monoclinic space group P2₁/n, with a = 13.583(3) Å, b = 16.959(3) Å, c = 18.860(4) Å, β = 94.71(3)° and Z = 4. The structure of I consists of isolated mononuclear molecules, the coordination number of La being 10. Thermal behaviour and composition of the vapor phase have been studied for I by thermal analysis and mass-spectrometry using a Knudsen cell. The mixed ligand complex I was found to sublime congruently in the temperature range 370–460 K: [La(hfa)₃(Phen)₂]_(s) = [La(hfa)₃(Phen)]_(g) + Phen_(g), Δ_rH⁰(T) = 316.2 ± 1.8 kJ/mol.     

Potential energy surface and rate constant of the inversion substitution reactions CH3X + O2 → CH3O2• + X• (X = SH,NO2)

The temperature dependence of the rate constant of the inversion substitution reactions CH₃X + O₂ → CH₃O₂^? + X^? (X = SH, NO₂), can be expressed as k = 6.8 × 10^–12(T/1000)^1.49exp(–62816 cal mol^–1/RT) cm³ s^–1 (X = SH) and k = 6.8 × 10^–12(T/1000)^1.26 × × exp(–61319 cal mol^–1/RT) cm³ s^–1 (X = NO₂), as found with the use of high-level quantum chemical methods and the transition state theory.     

A new intersecting tunnel structure in the AIMIII[PO3(OH)]2 series for AI = Ag,MIII = In: Analysis of structural relationships

A new indium hydroxyphosphate containing silver, AgIn[PO₃(OH)]₂, has been synthesized using hydrothermal method. It crystallizes in the P2₁/c space group with the cell parameters a = 6.6400(2) Å, b = 14.6269(6) Å, c = 6.6616(4) Å, β = 95.681(5)°, V = 643.82(6) Å³, Z = 4. Its three-dimensional framework, built up of corner-sharing PO₃(OH) tetrahedra and InO₆ octahedra, presents intersecting tunnels running along <111> and [100] directions, in which the Ag⁺ cations are located. The presence of hydroxyl groups has been confirmed from IR spectroscopy studies and hydrogen atoms were located from the single crystal X-ray diffraction study. The structural relationships with the other compounds of general formula A^IM^III[PO₃(OH)]₂ are analyzed.     

Thermochemistry of the biochemical reaction: { pyrophosphate(aq) + H2O(l) = 2 phosphate(aq)}

Calorimetric enthalpies of reaction have been measured for the overall biochemical reaction{pyrophosphate(aq)  +  H₂O(l)  =  2phosphate (aq)} . The reaction was catalyzed by alkaline phosphatase and, to simplify the thermochemistry, was carried out in the absence of Mg ^2 + (aq). Measurements were performed with phosphate buffer ( pH  =  7.19 and 7.94), PIPES buffer ( pH  =  7.13), and HEPES buffer ( pH  =  7.86). The results of these measurements were analyzed by using an equilibrium model. These calculations lead to the standard molar enthalpy changeΔ_rH_m^o =  − (17.3  ±  0.6)kJ·mol ^− 1 (temperature T =  298.15 K and ionic strengthI =  0) for the reference reaction{HP₂O₇^3 − (aq)  +  H₂O(l)  =  2HPO₄^2 − (aq)  +  H ⁺ (aq)} . Values of the apparent equilibrium constantK^′ for the overall biochemical reaction from the literature were also analyzed by using the equilibrium model in order to obtain what is believed to be a reliable value for the equilibrium constantK =  4.7 · 10 ^− 4 for the reference reaction. The values ofK and Δ_rH_m^o for the reference reaction have been used together with values from the CODATA tables to calculate standard molar formation properties for the pyrophosphate species.     

The enthalpy of dilution and thermodynamics of Na2CO3(aq) and NaHCO3(aq) fromT = 298 K toT = 523.15 K and pressure of 40 MPa

Molar enthalpies of dilution Δ_dilH_mofNa₂CO₃(aq) were measured from molality m =  1.45 mol · kg ^− 1to m =  0.008 mol · kg ^− 1at seven temperatures from T =  298 K toT =  523 K at the pressure p =  7 MPa, and at four temperatures fromT =  371 K to T =  523 K at the pressurep =  40 MPa. Molar enthalpies of dilutionΔ_dilH_m of NaHCO₃(aq) were measured fromm =  0.98 mol · kg ^− 1tom =  0.007 mol · kg ^− 1at the same temperatures and pressures. Hydrolysis and ionization equilibria contribute substantially to the measured enthalpies under many of the conditions of this study. Explicit consideration of these reactions, using thermodynamic quantities from previous studies, facilitates a quantitative representation of apparent molar enthalpies, activity coefficients, and osmotic coefficients with the Pitzer ion-interaction treatment over the ranges of temperature, pressure, and molality of the experiments.     

Apparent molar heat capacities and apparent molar volumes ofY2(SO4)3(aq),La2(SO4)3(aq),Pr2(SO4)3(aq),Nd2(SO4)3(aq),Eu2(SO4)3(aq),Dy2(SO4)3(aq),Ho2(SO4)3(aq), andLu2(SO4)3(aq)atT = 298.15 K andp = 0.1 MPa

The apparent molar heat capacities C_{p, φ} ^∘ and apparent molar volumes V_φ ^∘ of Y₂(SO₄)₃(aq), La₂(SO₄)₃(aq), Pr₂(SO₄)₃(aq), Nd₂(SO₄)₃(aq), Eu₂(SO₄)₃(aq), Dy₂(SO₄)₃(aq), Ho₂(SO₄)₃(aq), and Lu₂(SO₄)₃(aq) were measured at T =  298.15 K and p =  0.1 MPa with a Sodev (Picker) flow microcalorimeter and a Sodev vibrating-tube densimeter, respectively. These measurements extend from lower molalities of m =  (0.005 to 0.018) mol ·kg ^− 1to m =  (0.025 to 0.434) mol ·kg ^− 1, where the upper molality limits are slightly below those of the saturated solutions. There are no previously published apparent molar heat capacities for these systems, and only limited apparent molar volume information. Considerable amounts of the R SO₄ ⁺ (aq) and R(SO₄)₂ ⁻ (aq) complexes are present, where R denotes a rare-earth, which complicates the interpretation of these thermodynamic quantities. Values of the ionic molar heat capacities and ionic molar volumes of these complexes at infinite dilution are derived from the experimental information, but the calculations are necessarily quite approximate because of the need to estimate ionic activity coefficients and other thermodynamic quantities. Nevertheless, the derived standard ionic molar properties for the various R SO₄ ⁺ (aq) and R(SO₄)₂ ⁻ (aq) complexes are probably realistic approximations to the actual values. Comparisons indicate that V_φ ^∘ {RSO₄ ⁺ , aq, 298.15K}  =  − (6  ±  4)cm³· mol ^− 1and V_φ ^∘ {R(SO₄)₂ ⁻ , aq, 298.15K}  =  (35  ±  3)cm³· mol ^− 1, with no significant variation with rare-earth. In contrast, values of C_{p, φ} ^∘ { RSO₄ ⁺ , aq, 298.15K } generally increase with the atomic number of the rare-earth, whereas C_{p, φ} ^∘ { R(SO₄)₂ ⁻ , aq, 298.15K } shows a less regular trend, although its values are always positive and tend to be larger for the heavier than for the light rare earths.     

Synthesis and crystal structure of the first chain-type nitridosilicates RE5Si3N9 (RE = La,Ce)

The novel branched chain-type nitridosilicates Ce₅Si₃N₉ and La₅Si₃N₉ have been synthesized in a radio-frequency furnace starting from the respective metals and silicon diimide Si(NH)₂ at 1625 °C for La₅Si₃N₉ and 1650 °C for Ce₅Si₃N₉, respectively. The structure of Ce₅Si₃N₉ has been determined by single-crystal X-ray diffraction (Ce₅Si₃N₉, Cmca (no. 64), a = 10.567(2) Å, b = 11.329(2) Å, c = 15.865(3) Å, V = 1899.3 Å³, Z = 8, R₁ = 0.0391, 1480 independent reflections, 90 refined parameters). The structure of isotypic La₅Si₃N₉ has been refined by the Rietveld method, starting from single-crystal data of Ce₅Si₃N₉ (La₅Si₃N₉, Cmca (no. 64), a = 10.647(4) Å, b = 11.414(4) Å, c = 16.030(5) Å, V = 1948.1 Å³, Z = 8, R_P = 0.0348, R_F² = 0.0533). Both compounds are built up of alternating Q²- and Q³-type corner sharing SiN₄ tetrahedra with additional corner sharing Q¹-units attached to the Q³-tetrahedra pointing alternately in opposing directions. These zipper-like chains are intertwined in both directions perpendicular to the chain itself to form a three-dimensionally interlocked structure with the rare-earth ions situated between the chains. Magnetic measurements resulted in a ferromagnetic ground state with a magnetic moment in agreement with Ce³⁺.     

A calorimetric and thermodynamic investigation of A2[(UO2)2(MoO4)O2] compounds with A = K and Rb and calculated phase relations in the system (K2MoO4 + UO3 + H2O)

A calorimetric and thermodynamic investigation of two alkali-metal uranyl molybdates with general composition A₂[(UO₂)₂(MoO₄)O₂], where A = K and Rb, was performed. Both phases were synthesized by solid-state sintering of a mixture of potassium or rubidium nitrate, molybdenum (VI) oxide and gamma-uranium (VI) oxide at high temperatures. The synthetic products were characterised by X-ray powder diffraction and X-ray fluorescence methods. The enthalpy of formation of K₂[(UO₂)₂(MoO₄)O₂] was determined using HF-solution calorimetry giving Δ_fH° (T = 298 K, K₂[(UO₂)₂(MoO₄)O₂], cr) = −(4018 ± 8) kJ · mol⁻¹. The low-temperature heat capacity, С_р°, was measured using adiabatic calorimetry from T = (7 to 335) K for K₂[(UO₂)₂(MoO₄)O₂] and from T = (7 to 326) K for Rb₂[(UO₂)₂(MoO₄)O₂]. Using these С_р° values, the third law entropy at T = 298.15 K, S°, is calculated as (374 ± 1) J · K⁻¹ · mol⁻¹ for K₂[(UO₂)₂(MoO₄)O₂] and (390 ± 1) J · K⁻¹ · mol⁻¹ for Rb₂[(UO₂)₂(MoO₄)O₂]. These new experimental results, together with literature data, are used to calculate the Gibbs energy of formation, Δ_fG°, for both phases giving: Δ_fG° (T = 298 K, K₂[(UO₂)₂(MoO₄)O₂], cr) = (−3747 ± 8) kJ · mol⁻¹ and Δ_fG° (T = 298 K, Rb₂[(UO₂)₂(MoO₄)], cr) = −3736 ± 5 kJ · mol⁻¹. Smoothed С_р°(Т) values between 0 K and 320 K are presented, along with values for S° and the functions [H°(T) − H°(0)] and [G°(T) − H°(0)], for both phases. The stability behaviour of various solid phases and solution complexes in the (K₂MoO₄ + UO₃ + H₂O) system with and without CO₂ at T = 298 K was investigated by thermodynamic model calculations using the Gibbs energy minimisation approach.     

Syntheses and crystal structures of new vanadium(IV) oxyphosphates M(VO)2(PO4)2 with M = Co,Ni

We have extended our research interest on titanium oxyphosphates (M^II(TiO)₂(PO₄)₂, with M^II = Mg, Fe, Co, Ni, Cu, Zn) to vanadium oxyphosphates M^II(V^IVO)₂(PO₄)₂ (M^II = Co, Ni). For each compound two phases, named α and β according to synthesis conditions, have been stabilized at room temperature, then characterized. The four crystal structures M(VO)₂(PO₄)₂ (α and β for M = Co, Ni) have been determined in monoclinic P2₁/c space group using X-ray single crystals diffraction data. Structure of the α phase is derived from the Li(TiO)(PO₄) (orthorhombic Pnma) and LiNi_0.50(TiO)₂(PO₄)₂ (monoclinic P2₁/c) types, with cell parameters: a = 6.310(1) Å, b = 7.273(1) Å, c = 7.432(1) Å, β = 90.43(1)° for M = Co, and a = 6.297(2) Å, b = 7.230(2) Å, c = 7.421(2) Å, β = 90.36(2)° for M = Ni. Structure of the β phase is derived from the Ni(TiO)₂(PO₄)₂-type (monoclinic P2₁/c) with cell parameters: a = 7.2742(2) Å, b = 7.2802(2) Å, c = 7.4550(2) Å, β = 120.171(2)° for M = Co, and a = 7.2691(2) Å, b = 7.2366(2) Å, c = 7.4453(2) Å, β = 120.231(2)° for M = Ni. All these structures consist of a three dimensional (3D) framework built up of infinite chains of tilted corner-sharing [VO₆] octahedra, cross-linked by corner-sharing [PO₄] tetrahedra. The M²⁺ ion (M = Co, Ni) is located in a triangular based antiprism which shares faces with two [VO₆] octahedra. Structural filiation is discussed based on a common structural unit, a sheet where divalent cations M²⁺ (M = Co, Ni) are inserted. A thermal study of the α ? β transition is also presented.     

Controlling the dimensionality of oxalate-based bimetallic complexes: The ferromagnetic chain {[K(18-crown-6)][Mn(bpy)Cr(ox)3]}∞(18-crown-6 = C12H24O6, ox=C2O42-, bpy = C10H8N2)

The bimetallic ferromagnetic chain {[K(18-crown-6)][Mn(bpy)Cr(ox)₃]}_∞ (1) has been synthesized and characterized. It crystallizes in the orthorhombic chiral space group P2₁2₁2₁ [a = 9.0510(2) Å, b = 14.4710(3) Å, c = 26.8660(8) Å, V = 3510.97(1) Å³, Z = 2]. Compound 1 is made up by anionic [Mn(bpy)Cr(ox)₃]⁻ 1D chains and cationic [K(18-crown-6)]⁺ complexes. The magnetic exchange within the chain is ferromagnetic [J = +7.8(7) cm⁻¹]. In the solid state, the ferromagnetic chains are well isolated magnetically and no long range magnetic ordering has been observed above 2 K.     

Anomalous capacity and cycling stability of xLi2MnO3 · (1 − x)LiMO2 electrodes (M = Mn,Ni, Co) in lithium batteries at 50 °C

Transition metal oxides with composite xLi₂MnO₃ ·  (1 − x)LiMO₂ rocksalt structures (M = Mn, Ni, Co) are of interest as a new generation of cathode materials for high energy density lithium-ion batteries. After electrochemical activation to 4.6 or 4.8 V (vs. Li⁰) at 50 °C, xLi₂MnO₃ · (1 − x)LiMn_0.33Ni_0.33Co_0.33O₂ (x = 0.5, 0.7) electrodes deliver initial discharge capacities (>300 mAh/g) at a low current rate (0.05 mA/cm²) that exceed the theoretical values for lithiation back to the rocksalt stoichiometry (240–260 mAh/g), at least during the early charge/discharge cycles of the cells. Attention is drawn to previous reports of similar, but unaccounted and unexplained anomalous behavior of these types of electrode materials. Possible reasons for this anomalous capacity are suggested. Indications are that electrodes in which M = Mn, Ni and Co do not cycle with the same stability at 50 °C as those without cobalt.     

Lattice potential energies and thermochemical properties of triethylammonium halides (Et3NHX) (X = Cl,Br, and I)

A series of triethylammonium halides (Et₃NHCl, Et₃NHBr, and Et₃NHI) was synthesized. The crystal structures of the three compounds were characterized by X-ray crystallography. The lattice potential energies and ionic radius of the common cation of the three compounds were obtained from crystallographic data. Molar enthalpies of dissolution of the compounds at various values of molality were measured in the double-distilled water at T = 298.150 K by means of an isoperibol solution-reaction calorimeter. According to Pitzer’s theory, the values of molar enthalpies of dissolution at infinite dilution and Pitzer’s parameters of the compounds were obtained. The values of apparent relative molar enthalpies, relative partial molar enthalpies of the solvent and the compounds at different molalities were derived from the experimental values of molar enthalpies of dissolution of the compounds. Finally, hydration enthalpy of the common cation Et₃NH⁺ was calculated to be ΔH₊ = ?(150.386 ± 4.071) kJ · mol^?1 by designing a thermochemical cycle.     

Spectroscopic properties of RBiBO4 (R = Ca,Sr) glasses doped with TiO2

Transparent glasses, melt quenching derived, containing 10RO·20Bi₂O₃·(70 ? x)B₂O₃·xTiO₂ [R = Ca, Sr] with x = 0, 0.5, 1.0 wt% were characterized by X-ray powder diffraction. Physical and spectroscopic properties viz., density, absorption, emission, electron paramagnetic resonance (EPR) and FTIR were investigated. The absorption band around 823 nm in pure glass samples is attributed to the electronic transition of ³P₀ to ³P₂ of Bi⁺ radicals. A small absorption hump centered around 609 nm is found in all doped glasses due to ²T_2g to ²E_g transition of octahedral Ti³⁺ ions. The emission results revealed that all the samples exhibit a broad emission band covering entire visible-light range, with λ_ex = 360 nm, centered 470–520 nm corresponds to electronic transition of ³P₁ to ¹S₀ of Bi³⁺ ions, therefore the present materials can be potentially used as tunable or full-color display systems. And a strong emission around 706 nm with λ_ex = 514 nm due to transition of ²P_3/2 to ²P_1/2 of Bi²⁺ ions. In SrO mixed glasses Ti⁴⁺ ions effect the environment of Bi³⁺ ion symmetry units from C₂ to C_3i. A small EPR signal (at room temperature) is observed in titanium doped glasses due to Ti³⁺ ions. In both the series with increase of TiO₂ concentration BO₄ units are gradually converted into BO₃ units and new cross linkages are formed, like B–O–Ti, Bi–O–Ti at the expense of B–O–B bonds.     

On oxoacidic properties and solubilities of beryllium and magnesium oxides in molten (CsCs + KCl + NaCl) eutectic at T = 783 K

Reactions of Be²⁺ and Mg²⁺ with O^2– in molten eutectic mixture (CsCs + KCl + NaCl) (0.455:0.245:0.30) at T = 783 K were studied by a potentiometric method using Pt(O₂)|ZrO₂(Y₂O₃) indicator electrode. Addition of O^2– ions to the melt containing Mg²⁺ results in precipitation of MgO (pK_s,MgO = 11.89 ± 0.3, molality) whereas interaction of Be²⁺ with O^2– is accompanied with sequential formation of Be₂O²⁺ (pK = 15.68 ± 0.5, molality) and precipitation of BeO (pK_s,BeO = 9.62 ± 0.3, molality). On the basis of the obtained and known data pK_s,MgO–T⁻¹ dependence in molten (CsCs + KCl + NaCl) eutectic is constructed. The slope of the said dependence in T/K = (from 583 to 1073) range is in good agreement with the value predicted by the Shreder equation, that extends the range of use of the Shreder equation for predictions of metal oxide solubilities in molten halides.     

Crystal structures of Th(OH)PO4, U(OH)PO4 and Th2O(PO4)2. Condensation mechanism of MIV(OH)PO4 (M = Th,U) into M2O(PO4)2

Three new crystal structures, isotypic with β-Zr₂O(PO₄)₂, have been resolved by the Rietveld method. All crystallize with an orthorhombic cell (S.G.: Cmca) with a = 7.1393(2) Å, b = 9.2641(2) Å, c = 12.5262(4) Å, V = 828.46(4) Å³ and Z = 8 for Th(OH)PO₄; a = 7.0100(2) Å, b = 9.1200(2) Å, c = 12.3665(3) Å, V = 790.60(4) Å³ and Z = 8 for U(OH)PO₄; a = 7.1691(3) Å, b = 9.2388(4) Å, c = 12.8204(7) Å, V = 849.15(7) Å³ and Z = 4 for Th₂O(PO₄)₂. By heating, the M(OH)PO₄ (M = Th, U) compounds condense topotactically into M₂O(PO₄)₂, with a change of the environment of the tetravalent cation that lowers from 8 to 7 oxygen atoms. The lower stability of Th₂O(PO₄)₂ compared to that of U₂O(PO₄)₂ seems to result from this unusual environment for tetravalent thorium.     

Synthesis,structure and magnetic properties of 2-D and 3-D [cation]{M[Au(CN)2]3} (M = Ni, Co) coordination polymers

In order to study the templating effect of the cation and the resulting impact on the magnetic properties, reactions of M(II) salts with [cation][Au(CN)₂] were conducted, yielding a series of coordination polymers of the form [cation]{M[Au(CN)₂]₃} (cation = ⁿBu₄N⁺, PPN⁺ (bis(triphenylphosphoranylidene)ammonium); M = Ni(II) and Co(II)). The structures of ⁿBu₄N{M[Au(CN)₂]₃} and PPN{M[Au(CN)₂]₃} (M = Ni and Co) contain two distinct 3-D anionic frameworks of {M[Au(CN)₂]₃}⁻, hence the framework was sensitive to the cation, but not to the identity of the metal center. In ⁿBu₄N{M[Au(CN)₂]₃}, the metal centers are connected by [Au(CN)₂] units to form six 2-D (4, 4) rectangular grids that are fused through the M centers to yield a complex three-dimensional framework which accommodates the ⁿBu₄N⁺ cations. In PPN{M[Au(CN)₂]₃}, the framework adopts a simpler non-interpenetrated Prussian-blue-type pseudo-cubic array, with the PPN⁺ cations occupying each cavity; no reduction in dimensionality occurs despite the large cation size. In the presence of water, {Co(H₂O)₂[Au(CN)₂]₂} · ⁿBu₄N[Au(CN)₂] was obtained, a 2-D layered polymer that contains neutral sheets of {Co(H₂O)₂[Au(CN)₂]₂} which are separated by ⁿBu₄N[Au(CN)₂] layers; aurophilic interactions of 3.4250(13) Å and hydrogen-bonding connect the layers. The magnetic properties of all compounds were investigated by SQUID magnetometry. The Ni(II) polymers have similar magnetic behaviour, which are dominated by zero-field splitting with very weak antiferromagnetic interactions at low temperature (D ∼ 2–3 cm⁻¹, zJ < 1 cm⁻¹). The magnetic behaviour of all of the Co(II) polymers were found to be very similar, and dominated by single-ion effects (i.e. a large first-order orbital contribution). No significant magnetic coupling is observed in any of these coordination polymers, suggesting that the [Au(CN)₂] bridging unit behaves as a poor mediator of magnetic exchange in these high-dimensionality systems.     

(Solid + solute) phase equilibria in aqueous solution. XIII. Thermodynamic properties of hydrozincite and predominance diagrams for (Zn2 + + H2O + CO2)

The thermodynamic properties ofZn₅(OH)₆(CO₃)₂ , hydrozincite, have been determined by performing solubility and d.s.c. measurements. The solubility constant in aqueous NaClO₄media has been measured at temperatures ranging from 288.15 K to 338.15 K at constant ionic strength (I =  1.00 mol · kg ^− 1). Additionally, the dependence of the solubility constant on the ionic strength has been investigated up to I =  3.00 mol · kg ^− 1NaClO₄at T =  298.15 K. The standard molar heat capacity C_{p, m}^ofunction fromT =  318.15 K to T =  418.15 K, as well as the heat of decomposition of hydrozincite, have been obtained from d.s.c. measurements. All experimental results have been simultaneously evaluated by means of the optimization routine of ChemSage yielding an internally consistent set of thermodynamic data (T =  298.15 K): solubility constant log ^* K_{ps 0}⁰ =  (9.0  ±  0.1), standard molar Gibbs energy of formationΔ_fG_m^o {Zn₅(OH)₆(CO₃)₂ }  =  ( − 3164.6  ±  3.0)kJ · mol ^− 1, standard molar enthalpy of formation Δ_fH_m^o{Zn₅(OH)₆(CO₃)₂ }  =  ( − 3584  ±  15)kJ · mol ^− 1, standard molar entropy S_m^o{Zn₅(OH)₆(CO₃)₂ }  =  (436  ±  50)J · mol ^− 1· K ^− 1and C_p,m^o / (J · mol ^− 1· K ^− 1)  =  (119  ±  11)  +  (0.834  ±  0.033)T / K. A three-dimensional predominance diagram is introduced which allows a comprehensive thermodynamic interpretation of phase relations in(Zn^2 +  +  H₂O  +  CO₂) . The axes of this phase diagram correspond to the potential quantities: temperature, partial pressure of carbon dioxide and pH of the aqueous solution. Moreover, it is shown how the stoichiometric composition{n(CO₃) / n(Zn)} of the solid compoundsZnCO₃ and Zn₅(OH)₆(CO₃)₂can be checked by thermodynamically analysing the measured solubility data.     

Calorimetric investigation of mixing enthalpy of liquid (Co + Cu + Zr) alloys at T = 1873 K

The enthalpies of mixing of liquid (Co + Cu + Zr) alloys have been determined using the high-temperature isoperibolic calorimeter. The measurements have been performed along three sections (x_Co/x_Cu = 3/1, 1/1, 1/3) with x_Zr = 0 to 0.55 at T = 1873 K. Over the investigated composition range, the partial mixing enthalpies of zirconium are negative. The limiting partial enthalpies of mixing of undercooled liquid zirconium in liquid (Co + Cu) alloys are (−138 ± 18) kJ · mol⁻¹ (the section x_Co/x_Cu = 3/1), (−155 ± 10) kJ · mol⁻¹ (the section x_Co/x_Cu = 1/1), and (−130 ± 22) kJ · mol⁻¹ (the section x_Co/x_Cu = 1/3). The integral mixing enthalpies are sign-changing. The isenthalpic curves have been plotted on the Gibbs triangle. The main features of the composition dependence of the integral mixing enthalpy of liquid ternary alloys are defined by the pair (Co + Zr) and (Cu + Zr) interactions.     

Thermodynamics of dibenzo-p-dioxin and 1,2,3,4-tetrachlorodibenzo-p-dioxin fromT = 5 K toT = 490 K

In adiabatic low-pressure and dynamic calorimeters the temperature dependence of the standard molar heat capacity C_{p, m}^oof dibenzo- p -dioxin and 1,2,3,4-tetrachlorodibenzo- p -dioxin have been determined at temperatures in the range T =  5 K to T =  490 K: from T =  5 K to T =  340 K with an accuracy of about 0.2 per cent and with an accuracy of 0.5 per cent to 1.5 per cent between T =  340 K and T =  490 K. The temperatures, enthalpies, and entropies of melting of the above compounds have been determined. The experimental data were used to calculate the thermodynamic functions C_{p, m}^o / R, Δ₀^TH_m^o / (R·K), Δ₀^TS_m^o / R, and Φ_m^o = Δ₀^TS_m^o − Δ₀^TH_m^o / T(where R is the universal gas constant) in the range T →  0 to T =  490 K. The isochoric heat capacity C_{V, m}of both dioxins has been estimated over the range T →  0 to T_fus. The effect of substitution of four hydrogen atoms by chlorine atoms on the lattice and atomic components of the isochoric heat capacity was considered.