Effect of silver doping on the electrical properties of a-Sb2Se3

This paper reports the effect of Ag-doping on electrical properties of a-Sb₂Se₃ in the temperature range 230–340 K and frequency range 5–100 kHz. The variation of transport properties with thermal doping has been studied. Ag-doping produces two homogeneous phases in the sample, which are found to be voltage dependent in the temperature range studied and frequency dependent in lower frequency region (0.1–10 kHz). Activation energy E_g and C′ [= σ₀ exp (γ/k), where γ, is the temperature coefficient of the band gap] calculated from dc conductivity has been found to vary from (0.42 ± 0.01) eV to (0.26 ± 0.01) eV and (4.11 ± 0.01) × 10⁻⁵ to (2.90 ± 0.02) × 10⁻⁶ Ω⁻¹ cm⁻¹ respectively. Ag-doping can be used to make the sample useful in device applications.     

Optical characterization of sputtered amorphous aluminum nitride thin films by spectroscopic ellipsometry

We have measured and analyzed the optical constants and polarized optical properties of amorphous aluminum nitride (a-AlN) thin films deposited by RF reactive magnetron sputtering onto silicon(1 1 1) and glass substrates. The optical constants were obtained by analysis of the measured ellipsometric spectra in the wavelength range 300–1400 nm, using the Cauchy–Urbach model. Refractive indices and extinction coefficients of the films were determined to be in the range 1.80–2.11 and 8.6 × 10⁻³–1.5 × 10⁻⁵, respectively. Analysis of the absorption coefficient, in the wavelength range 200–1400 nm, shows the bandgap of a-AlN thin films to be 5.84 ± 0.05 eV. From the angle dependence of the p-polarized reflectivity we deduce a Brewster angle of 61° and a principal angle of 64°. Measurement of the polarized optical properties reveals a high transmissivity and very low absorptivity for a-AlN films in the visible and near infrared regions. X-ray diffraction analysis confirmed the amorphous nature of the films under study.     

Dielectric properties of bis(2,4 pentanedionato)copper(II) crystalline films grown on Si substrate for low-k applications

Bis(acetylacetonato)copper(II) thin films were prepared by sublimation at about 245 °C in vacuum on p-Si and glass substrates for dielectric and optical investigations. They were characterized by the X-ray diffraction (XRD) and energy-dispersion X-ray fluorescence (EDXRF) methods. The XRD pattern reveals that the prepared films were polycrystalline of monoclinic P2₁/n structure. The optical absorption spectrum of the prepared film was not identical to that of the molecular one, which identified by a strong absorption peak at 635 nm. The onset energy of the optical absorption of the complex was calculated by using Hamberg et al. method, which is usually used for common solid-state semiconductors and insulators. The dielectric properties for the complex as insulator were investigated on samples made in form of a metal-insulator-semiconductor (MIS) structure. The dielectric properties were studied in frequency range 1–1000 kHz and temperature range 298–333 K. The dielectric relaxation was analyzed in-terms of dielectric modulus M¹(ω). Generally, the present study shows that films of the complex grown on Si substrate are a promising candidate for low-k dielectric applications; it displays low-k value around 1.7 ± 0.1 at high frequencies.     

InOx semiconductor films deposited on glass substrates for transparent electronics

Transparent undoped semiconductor indium oxide films were deposited by radio frequency (rf) plasma enhanced reactive thermal evaporation (rf-PERTE) of indium at low substrate temperature. It was experimentally verified that the variation of rf power density has a strong influence on the electrical and structural properties of the films. The thickness of the InO_x films is of about 100 nm. Results show that InO_x films show an average visible transmittance of about 85% and energy gap of about 2.6 eV. Structural and electrical conductivity measurements show that films are polycrystalline and there exists a linear variation of conductivity logarithm vs reciprocal of temperature. Electrical conductivity variation of 17.6 to 5.8 × 10⁻³ (Ω cm)⁻¹ for films produced at rf power densities ranging from 3.9 to 78.1 mW cm⁻³ was obtained. This controllable semiconductor behavior can therefore satisfy the requirement of a particular application for these type of films.     

Electrical conductivity and dielectric relaxation in non-crystalline films of tungsten trioxide

Amorphous tungsten trioxide (a-WO₃) thin films were prepared by thermal evaporation technique. The electrical conductivity and dielectric properties of the prepared films have been investigated in the frequency range from 100 Hz to 100 kHz and in the temperature range 293–393 K. In spite of the absence of the dielectric loss peaks, application of the dielectric modulus formulism gives a simple method for evaluating the activation energy of the dielectric relaxation. The frequency dependence of σ(ω) follows the Jonscher’s universal dynamic law with the relation σ(ω) = σ_dc + Aω^s, where s is the frequency exponent. The conductivity in the direct regime, σ_dc, is described by the small polaron model. The electrical conductivity and dielectric properties show that Hunt’s model is well adapted to a-WO₃ films.     

Optical and electrical properties of as-prepared and annealed (Se80Te20)100 − xAgx (0 ≤ x ≤ 4) ultra-thin films

Optical and electrical properties of the (Se₈₀Te₂₀)_100 ? xAg_x (0 ≤ x ≤ 4) ultra-thin films have been studied. The ultra-thin films were prepared by thermal evaporation of the bulk samples. Thin films were annealed below glass transition temperature (328 K) and in between glass transition temperature and crystallization temperature (343 K). Thin films annealed at 343 K showed crystallization peaks for Se–Te–Ag phases in the XRD spectra. The transmission and reflection of as-prepared and annealed ultra-thin films were obtained in the 300–1100 nm spectral region. The optical band gap has been calculated from the transmission and reflection data. The refractive index has been calculated by the measured reflection data. It has been found that the optical band gap increases, but the refractive index, extinction coefficient, real and imaginary dielectric constant decrease with increase in Ag content. The optical band gap and refractive index show the variation in their values with increase in the annealing temperature. The extinction coefficient increases with increasing annealing temperature. The surface morphology of ultra-thin films has been determined using a scanning electron microscope (SEM). The measured dc conductivity, under a vacuum of 10^? 5 mbar, showed thermally activated conduction with single activation energy in the measured temperature range (288–358 K) and it followed Meyer–Neldel rule. The dc activation energy decreases with increase in Ag content in pristine and annealed films. The results have been analyzed on the bases of thermal annealing effects in the chalcogenide thin films.     

Fabrication and ionic conductivity of amorphous Li–Al–Ti–P–O thin film

Li⁺ ion conducting Li–Al–Ti–P–O thin films were fabricated on ITO-glass substrates at various temperatures from 25 to 400 °C by RF magnetron sputtering method. When the substrate temperature is higher than 300 °C, severe destruction of ITO films were confirmed by XRD (X-ray diffraction) and the abrupt transformation of one semi-circle into two semi-circles on the impedance spectra. These as-deposited Li–Al–Ti–P–O solid state electrolyte thin films have an amorphous structure confirmed by XRD and a single semicircle on the impedance spectra. Good transmission higher than 80% in the visible light range of these electrolyte thin films can fulfill the demand of electro-chromic devices. Field emission scanning electron microscopy and atomic force microscopy showed the denser, smoother and more uniform film structure with the enhanced substrate temperature. Measurements of impedance spectra indicate that the gradual increased conductivity of these Li–Al–Ti–P–O thin films with the elevation of substrate temperature from room temperature to 300 °C is originated from the increase of the pre-exponential factor (σ₀). The largest Li-ion conductivity can come to 2.46 × 10^? 5 S cm^? 1. This inorganic solid lithium ion conductor film will have a potential application as an electrolyte layer in the field such as lithium batteries or all-solid-state EC devices.     

Correlation between the method of preparation and the properties of the sol–gel HfO2 thin films

This work describes the preparation of HfO₂ thin films by the sol–gel method, starting with different precursors such as hafnium ethoxide, hafnium 2,4-pentadionate and hafnium chloride. From the solution prepared as mentioned above, thin films on silicon wafer substrates have been realized by ‘dip-coating’ with a pulling out speed of 5 cm min^?1. The films densification was achieved by thermal treatment for 10 min at 100 °C and 30 min at 450 °C or 600 °C, with a heating rate of 1 °C min^?1. The structural and optical properties of the films are determined employing spectroellipsometric (SE) measurements in the visible range (0.4–0.7 μm), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). The main objective of this paper was to establish a correlation between the method of preparation (precursor, annealing temperature) and the properties of the obtained films. The samples prepared from pentadionate and ethoxide precursors are homogenous and uniform in thickness. The samples prepared starting from chloride precursor are thicker and proved to be less uniform in thickness. Higher non-uniformity develops in multi-deposition films or in crystallized films. A nano-porosity is present in the quasi-amorphous films as well in the crystallized one. For the samples deposited on silicon wafer, the thermal treatment induced the formation of a SiO₂ layer at the coating–substrate interface.     

Effect of proton irradiation on electrical properties of a-As2S3

This paper reports the effect of proton irradiation on the electrical properties of a-As₂S₃ in the temperature range of 323–418 K and frequency range 0.1–100 kHz. The variation of transport property is studied with proton irradiation dose (1 × 10¹³ ions/cm² and 1 × 10¹⁵ ions/cm²). It has been observed that proton irradiation changes the dc conductivity (σ_dc), dc activation energy (ΔE_dc) and ac conductivity (σ_ac(ω)). The σ_dc and σ_ac(ω) increases with dose of proton irradiation. The value of frequency exponent (s) decreases with the temperature and irradiation dose. These results are explained in terms of change in density of defect states in these glasses.     

Influence of oxygen partial pressure on the properties of undoped InOx films deposited at room temperature by rf-PERTE

Transparent and conductive/semiconductive undoped indium oxide (InO_x) thin films were deposited at room temperature. The deposition technique used is the radio frequency (rf) plasma enhanced reactive thermal evaporation (rf-PERTE) of indium (In) in the presence of oxygen. The influence of oxygen partial pressure on the properties of these films is presented. The oxygen partial pressure varied between 3 × 10^?2 and 1.3 × 10^?1 Pa. Undoped InO_x films, 100 nm thick, deposited at the oxygen partial pressure of 6 × 10^?2 Pa show a conductive behaviour, exhibit an average visible transmittance of 81%, a band gap around 2.7 eV and an electrical conductivity of about 1100 (Ω cm)^?1. For oxygen pressures greater than 6 × 10^?2 Pa, semiconductive films are obtained, maintaining the visible transmittance. Films deposited at lower pressures are conductive but dark. From XPS data, films deposited at an oxygen partial pressure of 6 × 10^?2 Pa show the highest amount of oxygen in the film surface and the lowest ratio between oxygen in the oxide crystalline and amorphous phases.     

Fabrication and characterization of transparent conductive ZnO:Al thin films prepared by direct current magnetron sputtering with highly conductive ZnO(ZnAl2O4) ceramic target

Using a highly conductive ZnO(ZnAl₂O₄) ceramic target, c-axis-oriented transparent conductive ZnO:Al₂O₃ (ZAO) thin films were prepared on glass sheet substrates by direct current planar magnetron sputtering. The structural, electrical and optical properties of the films (deposited at different temperatures and annealed at 400°C in vacuum) were characterized with several techniques. The experimental results show that the electrical resistivity of films deposited at 320°C is 2.67×10⁻⁴ Ω cm and can be further reduced to as low as 1.5×10⁻⁴ Ω cm by annealing at 400°C for 2 h in a vacuum pressure of 10⁻⁵ Torr. ZAO thin films deposited at room temperature have flaky crystallites with an average grain size of ∼100 nm; however those deposited at 320°C have tetrahedron grains with an average grain size of ∼150 nm. By increasing the deposition temperature or the post-deposition vacuum annealing, the carrier concentration of ZAO thin films increases, and the absorption edge in the transmission spectra shifts toward the shorter wavelength side (blue shift).     

Surface morphology of spin-coated As–S–Se chalcogenide thin films

Surface morphology and roughness of amorphous spin-coated As–S–Se chalcogenide thin films were determined using atomic force microscopy. Prepared films were coated from butylamine solutions with thicknesses d ∼ 100 nm and then annealed in a vacuum furnace at 45 °C and 90 °C for 1 h for their stabilization. The root mean square surface roughness analysis of surfaces of as-deposited spin-coated As–S–Se films indicated a very smooth film surface (with R_q values 0.42–0.45 ± 0.2 nm depending on composition). The nanoscale images of as-deposited films confirmed that surface of the films is created by domains with dimensions 20–40 nm, which corresponds to diameters of clusters found in solutions. The domain character of film surfaces gradually disappeared with increasing annealing temperature while the solvent was removed from the films. Middle-infrared transmission spectra recorded a decrease of intensities of vibration bands connected to N–H (at 3367 and 3292 cm⁻¹) and C–H (at 2965, 2935 and 2880 cm⁻¹) stretching vibrations. Temperature regions of solvent evaporation T = 60–90 °C and glass transformation temperatures T_g = 135–150 °C of spin-coated As–S–Se thin films were determined using a modulated differential scanning calorimetry.     

I–V Characteristics of tris(2,4-pentanedionato)manganese(III) thin films

Amorphous thin films of tris(acetylacetonate)manganese(III) were deposited on Si(P) substrates by thermal sublimation in vacuum. The deposited films were probed with X-ray fluorescence. Their electrical properties were studied as insulators for Al/Mn(acac)₃/Si(P) metal–insulator–semiconductor devices. Those devices were characterized by the measurement of the gate-voltage dependence of their capacitance, from which the relative permittivity (RP) and density of the charges in the insulator were determined. It was found that values of the RP of tris(acetylacetonate)manganese(III) films grown on Si(P) wafers were in the range of 30–40, which can be find applications in gate related technological uses. The dc-electrical conduction in the complex film was studied at room temperature and in temperature range of (293–325 K). It was found that the data of the as-deposited films follow the trap-charge-limited space-charge-limited conductivity (TCL-SCLC) mechanism, while the data of the annealed sample in vacuum of about 10⁻³ Pa at about 100 °C for 10 min obey the Richardson–Schottky (RS) mechanism. The parameters of both mechanisms were determined. It was concluded that the density of charged defects in the insulating film is critically determined the mechanism of the current-transfer.     

Effect of tellurium deposition rate on the properties of Cu–In–Te based thin films and solar cells

To investigate the effects of tellurium (Te) deposition rate on the properties of Cu–In–Te based thin films (Cu/In=0.30–0.31), the films were grown on both bare and Mo-coated soda-lime glass substrates at 200 °C by co-evaporation using a molecular beam epitaxy system. The microstructural properties were examined by means of scanning electron microscopy and X-ray diffraction. The crystalline quality of the films was improved with increase in the deposition rate of Te, and exhibited a single CuIn₃Te₅ phase with a highly preferred (1 1 2) orientation. Te-deficient film (Te/(Cu+In)=1.07) grown with a low Te deposition rate showed a narrow bandgap of 0.99 eV at room temperature. The solar cell performance was affected by the deposition rate of Te. The best solar cell fabricated using CuIn₃Te₅ thin films grown with the highest deposition rate of Te (2.6 nm/s) yielded a total area (0.50 cm²) efficiency of 4.4% (V_oc=309 mV, J_sc=28.0 mA/cm², and FF=0.509) without light soaking.     

Molecular dynamics in glass-forming poly(phenyl methyl siloxane) as investigated by broadband thermal,dielectric and neutron spectroscopy

The molecular dynamics of glass-forming poly(methyl phenyl siloxane) (PMPS) is studied by thermal (10⁻³–5 × 10² Hz), dielectric (10⁻³–10⁹ Hz) and neutron (5 × 10⁸–10¹² Hz) spectroscopy. Because of the broad frequency range of 15 orders of magnitude the study provides a precise determination of glassy dynamics in a wide temperature range using different probes. The relaxation rates extracted from the different methods agree quantitatively in both their absolute values and in their temperature dependencies. A detailed analysis of the temperature dependence of the relaxation rate f_p by a derivative technique shows that the α-relaxation of PMPS has to be characterized by a high and a low temperature branch separated by a crossover temperature T_B = 250 K. In both temperature ranges the temperature dependence of f_p has to be described by Vogel/Fulcher/Tammann laws with different Vogel temperatures. Also the analysis of the dielectric strength in its temperature dependence gives a crossover behavior from a low to a high temperature region with a similar value of T_B. T_B can be interpreted as onset of cooperative fluctuations and the formation of dynamical heterogeneities. The dependence of the relaxation rate on the scattering vector Q extracted from neutron scattering obeys a power law τ ∼ Q^−Slope, where the power Slope varies between Slope = 2 and Slope = 3.5 with increasing temperature. This anomalous dependence of the relaxation time on the momentum transfer is discussed in terms of dynamic heterogeneities in the underlying motional processes even at temperatures above T_B. Besides the segmental dynamics the fast Methyl group rotation is considered as well. The relaxation rates of this process have an activated temperature dependence with an activation energy of 8.3 kJ/mol. The data were discussed in the framework of the threefold jump model were the incoherent elastic scattering from ‘fixed’ atoms which are frozen on the time scale of the Methyl group rotation was taken into account.     

Amorphous tungsten-doped In2O3 transparent conductive films deposited at room temperature from metallic target

Amorphous tungsten-doped In₂O₃ (IWO) films were deposited from a metallic target by dc magnetron sputtering at room temperature. Both oxygen partial pressure and sputtering power have significant effects on the electrical and optical properties of the films. The as-deposited IWO films with the optimum resistivity of 5.8 × 10^?4 Ω·cm and the average optical transmittance of 92.3% from 400 to 700 nm were obtained at a W content of 1 wt%. The average transmittance in the near infrared region (700–2500 nm) is 84.6–92.8% for amorphous IWO prepared under varied oxygen partial pressure. The mobility of the IWO films reaches its highest value of 30.3 cm² V^?1 s^?1 with the carrier concentration of 1.6 × 10²⁰ cm^?3, confirming their potential application as transparent conductive oxide films in various flexible devices.     

Characteristics of heteroepitaxial Cu2−xMnxO/Nb–SrTiO3 p–n junction

Mn-doped cuprous oxide Cu_2?xMn_xO (CMO), where x = 0.03, is a p-type diluted magnetic semiconductor (DMS) with Curie temperature above room temperature [M. Wei, N. Braddon, et al., Appl. Phys. Lett. 86 (2005) 0725141; Y.L. Liu, S. Harrington, et al., Appl. Phys. Lett. 87 (2005) 222108]. We have grown CMO (x = 0.03) thin films of about 200 nm thick on n-type semiconducting (0 0 1)Nb–SrTiO₃(NSTO) single crystal substrates by pulsed laser deposition. Cubic crystalline phases of CMO layers were obtained in a narrow deposition pressure window of about 20 mTorr at growth temperature of 650 °C. X-ray diffraction and TEM studies of these heterostructures reveal a cube-on-cube epitaxial relationship of [CMO]₀₀₁/[NSTO]₀₀₁. All the oxide p–n junctions with the size of 500 × 500 μm were fabricated by the shadow masking technique. These junctions show highly asymmetric I–V characteristics. The rectification ratio at room temperature is about 10³ at ±2 V. Leakage current density of 10^?4 A cm^?2 at ?1 V is observed. No apparent junction breakdown is recorded at reverse bias voltages down to ?5 V. From the 1/C²–V plots, the forward bias turn on voltage is ～1.4 V. Clear junction current rectifying property is maintained at up to 200 °C. Our results have demonstrated that epitaxial CMO films can be fabricated on lattice matched cubic substrates. They are suitable DMS for above room temperature spintronic junction applications.     

Conductivity and dielectric properties of polyvinyl alcohol–polyvinylpyrrolidone poly blend film using non-aqueous medium

Several methods such as copolymerization, plasticization and blending etc., have been used to modulate the conductivity of polymer electrolytes. Polymer blending is one of the most important contemporary ways for the development of new polymeric materials and it is a useful technique for designing materials with a wide variety of properties. Polymer blend electrolyte has been prepared with different concentrations of PVA and PVP by solution casting technique using DMSO as solvent. The prepared films have been investigated by different techniques. The increase in amorphous nature of the polymer electrolytes has been confirmed by XRD analysis. The FTIR analysis reveals that the interchain hydrogen bonding within a PVA–PVP blends. The dielectric permittivity (ε*) and modulus (M*) have been calculated from the ac impedance spectroscopy in the frequency range 42 Hz– 1 MHz and the temperature range 308–373 K. The maximum conductivity has been found to be 1.58 × 10^? 6 S cm^? 1 at room temperature for 70PVA:30PVP concentration. The conductivity has been increased to 5.49 × 10^? 5 S cm^? 1 when the temperature is increased to 373 K. The activation energy of all samples was calculated using the Arrhenius plot and it has been found to be 0.53 eV to 0.78 eV.     

Synthesis and characterizations of phthaloyl chitosan-based polymer electrolytes

Phthaloyl chitosan (PhCh) has been synthesized by reacting excess phthalic anhydride with chitosan in the presence of nitrogen gas (N₂). Confirmation of phthaloyl chitosan structure by Fourier-transform infrared (FTIR) spectroscopy shows bands at 1773 and 1713 cm^? 1 attributable to the pthalimido group. From X-ray diffraction (XRD), the samples are largely amorphous. Thermal stability of chitosan is increased on phthaloylation. Ammonium thiocyanate (NH₄SCN) salt has been added to the solution of phthaloyl chitosan in N,N-dimethylformamide (DMF) before casting to form films. The amount of NH₄SCN salt added ranges from 5 to 50 wt. % concentration. The highest conductivity at 298 K is (2.42 ± 0.01) × 10^? 5 S cm^? 1 for the sample 70 wt. % PhCh-30 wt. % NH₄SCN. Impedance of the films has been measured at temperatures between 298 K and 373 K and in the frequency range from 0.1 Hz to 1 × 10⁷ Hz. Relaxation peaks are observed from dielectric loss and tangent delta variation with frequency at ambient and elevated temperatures in the frequency range investigated for the highest conducting sample. Decomposition voltage is ~ 2.07 V and transference number measurements show that charge conduction is mainly by ions.     

Characterization of a-B5C:H prepared by PECVD of orthocarborane: Results of preliminary FTIR and nuclear reaction analysis studies

The electronic properties of a-Si:H vary with hydrogen passivation of dangling bond defects. It appears this effect is also operative in semiconducting amorphous hydrogenated boron carbide (a-B₅C:H). Therefore, the ability to quantify the amount of hydrogen will be key to development of the materials science of a-B₅C:H. The results of an initial investigation probing the ability to quickly correlate hydrogen concentration in a-B₅C:H films with infrared spectroscopy are reported. a-B₅C:H thin films were growth on Si (1 1 1) substrates by plasma-enhanced chemical vapor deposition (PECVD) using sublimed orthocarborane and argon as the precursor gas. Nuclear reaction analysis (NRA) was performed to quantify the atomic concentration of H in the a-B₅C:H films. While the observed vibronic structure does not show stretches due to terminal C–H or bridging B–H–B, analysis of the terminal B–H stretch at ～2570 cm^?1 gives a proportionality constant of A = 2 × 10²² cm^?2. We conclude that the methods previously developed for correlating H concentration to infrared data in a-Si:H are similarly viable for a-B₅C:H films.