Precipitation of zinc ferrite nanoparticles in the Fe2O3–ZnO–SiO2 glass system

Glass materials in the ZnO–Fe₂O₃–SiO₂ system, containing zinc ferrite nanoparticles, were prepared by the sol–gel method and characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), Mössbauer spectroscopy, AC- and DC-magnetization techniques. The gel samples, dried at 130 °C, were further heat treated in air at 500 and 800 °C. At 500 °C zinc ferrite and hematite nanoparticles, with an average size of approximately 24 nm, were precipitated in the brown and opaque 10ZnO–10Fe₂O₃–80SiO₂ and in the ruby colored transparent 5ZnO–5Fe₂O₃–90SiO₂ and 2.5ZnO–2.5Fe₂O₃–95SiO₂ glass matrices. In the 5ZnO–5Fe₂O₃–90SiO₂ sample the nanoparticles exhibited ferro or ferrimagnetic interactions combined with superparamagnetism with a blocking temperature of approximately 14 K. Heating at 800 °C seems to cause partial dissolution of the zinc ferrite and hematite particles in all the investigated compositions. Accordingly at 800 °C the 5ZnO–5Fe₂O₃–90SiO₂ glass shows a paramagnetic behavior down to 2 K.     

Soda lime zirconia silicate glasses as prospective hosts for zirconia-containing radioactive wastes

Na₂O–CaO–ZrO₂–SiO₂ glass compositions with ZrO₂ contents of up to 20 mol% were melted. Up to 12.3 mol% ZrO₂ could be dissolved into the glasses. Melting temperatures ⩾1450 °C were required to remove seed and produce a melt that could be cast. Addition of ZrO₂ caused an increase in the glass transition and crystallization temperatures. Glasses crystallized at temperatures ⩾1050 °C with Keldyshite and Parakeldyshite (Na₂O · ZrO₂ · 2SiO₂) as the crystalline phases. Addition of up to 4.6 mol% ZrO₂ caused an increase in the hydrolytic resistance of the glass, with further additions having little effect. The suitability of these glasses as hosts for ZrO₂-containing radioactive wastes is discussed.     

Microstructural characteristics and crystallization of CaO–P2O5–Na2O–ZnO glass ceramics prepared by sol–gel method

Porous phosphate-based glass ceramics prepared by the sol–gel method were characterized using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and differential thermal analysis (DSC). The 48CaO–45P₂O₅–2ZnO–5Na₂O glassy system can remain fully amorphous up to 550 °C. After heat treated at 650 °C, the obtained porous bodies consisted of dense struts and macropores where β-Ca₂P₂O₇ and Na₂CaP₂O₇ phases crystallized from the glass matrix. When treated at 750 °C, Ca₄P₆O₁₉ and NaZn(PO₃)₃ precipitated homogeneously as new phases among the residual glass matrix. The material was assessed by soaking samples in phosphate-based buffer solution (PBS) solution to determine the solubility and observe apatite formation.     

Performance investigation of Li2O–Al2O3–4SiO2 based glass–ceramics with B2O3, Na3AlF6 and Na2O fluxes

Influence of single fluxes (10 wt.% B₂O₃), bi-component fluxes (4 wt.% B₂O₃ + 6 wt.% Na₃AlF₆), and complex fluxes (4 wt.% B₂O₃ + 4 wt.% Na₃AlF₆ + 2 wt.% Na₂O) on the thermal kinetic parameters, microstructure, flexural strength and coefficient of thermal expansion (CTE) of Li₂O–Al₂O₃–4SiO₂ (LAS) glass–ceramics was investigated through differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscope (SEM). The results showed that complex fluxes could efficiently decrease transition temperature (T_g) and crystallization temperature (T_p), and accelerate the formation of needle-like β-spodumene crystals which benefit high flexural strength. The homogeneous LAS glass–ceramic (sample C₃) which has a high strength of 132.4 MPa and low CTE (100–650 °C) of 2.74 × 10^? 6/°C is obtained by doping of the initial LAS glass by complex fluxes of 4 wt.% B₂O₃, 4 wt.% Na₃AlF₆, and 2 wt.% Na₂O, nucleating at 630 °C/120 min and then crystallized at 780 °C/120 min. It is worthy of further investigation as a bonder of diamond composite material due to its outstanding prosperities.     

Continuous compositional changes of crystal and liquid during crystallization of a sodium calcium silicate glass

This paper deals with a systematic study of crystal nucleation and growth kinetics in a 14.6Na₂O–34.0CaO–51.4SiO₂ mol% glass, which is close to the CaO · SiO₂–Na₂O · SiO₂ pseudo-binary section, just left of the stoichiometric Na₂O · 2CaO · 3SiO₂ (N₁C₂S₃) compound. We show that crystallization begins with nucleation of a Na_4+2xCa_4−x[Si₆O₁₈] (0 < x < 1) solid solution that is enriched in sodium as compared with both parent glass and the N₁C₂S₃ compound; while a fully crystallized sample is composed only by a solid solution that is stable at very high temperatures, but is metastable in the temperatures under investigation. We thus confirm a continuous compositional change of the crystals during the course of crystallization.     

Reactions between sol–gel coatings and some technical glass substrates during consolidation

SiO₂ and Na₂O–SiO₂ coatings have been applied on float glass and other technical glass substrates by a sol–gel dip-coating process. After drying and baking these films at temperatures up to 500 °C and for times up to 1020 min, the in-depth profiles of the different constituents were measured by secondary neutral mass spectrometry (SNMS). Sn, Al, and Si turned out to be immobile, whereas a diffusion coefficient of ≈10⁻¹⁷ cm²/s could be evaluated for Mg at 500 °C for the transport from float glass into the films. Ca diffused a little faster, however, especially for the Na₂O–SiO₂ films a saddle point and finally a peak occurred in the interface region. This interface peak was even stronger for Na, showing quite anomalous profiles. The mechanism of this peak formation is explained mainly as an up-hill diffusion process. According to this model at the interface non-bridging –O⁻ ions are formed, whose electroneutrality has to be maintained by mobile cations like Na⁺ and Ca²⁺, even diffusing against their own concentration gradient. The other glass substrates, two borofloat glasses and an alkali-poor display glass showed similar but less pronounced effects.     

Kinetic fragility of hydrous soda-lime-silica glasses

The effect of hydration on the kinetic fragility of soda-lime-silica glasses was investigated by viscometry in the glass transition range. Water-bearing glasses were prepared from industrial float glass (FG) and a ternary model glass (NCS = 16Na₂O 10CaO 74SiO₂ in mol%) by bubbling steam through the melt at 1480 °C and up to 7 bar. Additionally, a sodium borosilicate glass (NBS = 16Na₂O 10B₂O₃ 74SiO₂ in mol%) was hydrated under equal conditions. As detected by infrared spectroscopy water dissolves in the glasses exclusively as OH-groups. The hydration resulted in a total water content C_W up to ≈ 0.2 wt% for FG, NCS and NBS glasses. Kinetic fragility, expressed by the steepness index m, was determined from the temperature dependence of η at the glass transition. Viscosity data from previous studies on hydrous float glasses (C_W > 1 wt%) were surveyed together with literature data on the (H₂O)–Na₂O–CaO–SiO₂, (H₂O)–Na₂O–SiO₂ and (H₂O)–SiO₂ systems to expand the range of water concentration and bulk composition. We could demonstrate that m decreases for all glasses although water is dissolved as OH and should depolymerize the network. An empirical equation of the general type m = a ? b logC_W where a, b are fitting parameters, enables m to be predicted, for each glass series as function of the water content C_W. The enlarged data base shows that the parameter B of the Arrhenius viscosity-temperature relation decreases much stronger than the isokom temperature at the glass transition.     

Thermal conductivity of mixed alkali silicate glasses at low temperature

Thermal conductivity of glass is one of the fundamental properties of it. However, that has not been studied enough. That of only less than 20 compositions has been measured below the room temperature. In this study, we measured the thermal conductivity of xNa₂O · (100 ? x)SiO₂ and (33 ? y)Na₂O · yCs₂O · 67SiO₂ glasses by a transient heating method in the temperature range from about 150 K to room temperature. The conductivity of xNa₂O · (100 ? x)SiO₂ is found to decrease with the increase in alkali content. The dominant factor of this behavior is the decrease in phonon mean free path, which is due to the increase of non-bridge oxygen. Thermal conductivity of (33 ? y)Cs₂O · yNa₂O · 67SiO₂ is decreased with the increase in Cs₂O/(Na₂O + Cs₂O) ratio. The dominant factor of this behavior is the decrease of sound velocity. However, composition dependence of the phonon mean free path also affects the thermal conductivity. Phonon mean free path of 33Cs₂O · 67SiO₂ glass is longer than that of 33Na₂O · 67SiO₂ glass, and should be related to the change in distribution of structural unit in glass. In addition, phonon mean free path of mixed alkali glasses are shorter than that of single alkali glasses.     

Mechanism of crystallization of fast fired mullite-based glass–ceramic glazes for floor-tiles

The mechanism of crystallization from a B₂O₃-containing glass, with composition based in the CaO–MgO–Al₂O₃–SiO₂ system, to a glass–ceramic glaze was studied by different techniques. Glass powder pellets were fast heated, simulating current industrial tile processing methods, at several temperatures from 700 to 1200 °C with a 5 min hold. Microstructural study by field emission scanning electron microscopy revealed that a phase separation phenomenon occurred in the glass, which promoted the onset of mullite crystallization at 900 °C. The amount of mullite in the glass heated between 1100 and 1200 °C was around 20 wt%, as determined by Rietveld refinement. The microstructure of the glass–ceramic glaze heated at 1160 °C consisted of interlocked, well-shaped, acicular mullite crystals longer than 4 μm, immersed in a residual glassy phase.     

Medium range order in sodium silicate glasses: role of the network modifier

The effect of different concentrations of the network modifier Na₂O on the position of the Boson peak, observed in the low frequency Raman scattering experiments, is analyzed. Glasses containing 25% Na₂O (Na₂O · 4SiO₂) and 33% Na₂O (Na₂O · 2SiO₂) are compared with pure SiO₂ glass. The observed shift of the Boson peak is interpreted in terms of a change of a correlation length, ℓ, corresponding to some medium range order. This length, ℓ, decreases when the amount of sodium oxide increases.     

Synthesis and photoluminescence of Eu3+-doped ZnO–Ga2O3–SiO2 nano-glass-ceramics

Transparent rare-earth Eu³⁺-doped ZnO–Ga₂O₃–SiO₂ nano-glass-ceramics were obtained by a sol–gel method. X-ray diffraction and transmission electron microscopy were used to characterize the as-synthesized materials. Results showed that ZnGa₂O₄ nanocrystals with the size of 5 nm were precipitated from ZnO–Ga₂O₃–SiO₂ system and dispersed in the SiO₂-based glass when the heat-treatment temperature was up to 800 °C. Photoluminescence characterization of Eu³⁺-doped ZnO–Ga₂O₃–SiO₂ nano-glass-ceramics was carried out and the results show that the as-synthesized material display intense emission at 615 nm belonging to ⁵D₀ → ⁷F₂ transition.     

Structural investigations of nitrided Nb2O5 and Nb2O5–SiO2 sol–gel derived films

Sol–gel derived xNb₂O₅–(100 ? x)SiO₂ films (where x = 100, 80, 60, 50, 40, 20, 0 mol%) were nitrided at various temperatures (800 °C, 900 °C, 1000 °C, 1100 °C and 1200 °C). The structural transformations occurring in the films as a result of ammonolysis were studied using X-ray diffraction (XRD), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The XRD results have shown that the temperatures below 1100 °C were too low to obtain a pure NbN phase in the samples. The AFM observations indicate that the formation of the NbN phase and the size of NbN grains are related to the silica content in the layer. NbN grains become more regular and larger as the niobium content increases. The maximum grain size of about 100 nm was observed for x = 100. Preparation of the Nb₂O₅–SiO₂ sol–gel derived layers and the subsequent nitridation is a promising method of inducing crystalline NbN in amorphous matrices. It follows from the XPS results that a small amount of Nb₂O₅ remains in the films after nitridation at 1200 °C and that nitrogen reacted not only with Nb₂O₅ but also with SiO₂.     

In situ crystallization of lithium disilicate glass: Effect of pressure on crystal growth rate

Crystallization of a Li₂O · 2SiO₂ (LS₂) glass subjected to a uniform hydrostatic pressure of 4.5 and 6 GPa was investigated up to a temperature of 750 °C. The density of the compressed glass is ∼2% greater at 4.5 GPa than 1 atm and, depending on the processing temperature, up to 10% greater at 6 GPa. Crystal growth rates investigated as a function of temperature and pressure show that lithium disilicate crystal growth is an order of magnitude slower at 4.5 GPa than 1 atm resulting in a shift of +45 °C (±10 °C) in the growth rate curve at high pressure compared to 1 atm conditions. At 6 GPa lithium disilicate crystallization is suppressed entirely, while a new high pressure lithium metasilicate crystallizes at temperatures 95 °C (±10 °C) higher than those reported for lithium disilicate crystallization at 1 atm. The observed decrease in crystal growth rate with increasing pressure for the lithium disilicate glass up to 750 °C is attributed to an increase in viscosity with pressure associated with fundamental changes in glass structure accommodating densification.     

Thermal properties and glass formation in the SiO2–B2O3–Bi2O3–ZnO quaternary system

Lead-free glasses in the SiO₂–B₂O₃–Bi₂O₃–ZnO quaternary system were studied. The glass formation region, as determined by XRD patterns of bulk samples, was limited to glasses having more than 40 mol% of the glass-forming oxides SiO₂ and B₂O₃. Crystalline phases of Zn₂SiO₄ (willemite) were detected in compositions of 30SiO₂ · 10B₂O₃ · 20Bi₂O₃ · 40ZnO and 20SiO₂ · 10B₂O₃ · 25Bi₂O₃ · 45ZnO. Glass transition temperatures (T_g), dilatometric softening points (T_d) and linear coefficients of expansion in the temperatures range of 25–300 °C (α_25–300) were measured for subsystems along the B₂O₃ join of 10, 20 and 30 mol%. For these subsystems, T_g ranged from 411 to 522 °C, and T_d ranged from 453 to 563 °C, both decreasing with increasing Bi₂O₃ content. The measured α_25–300 ranged from 53 to 95 × 10⁻⁷ °C⁻¹, with values increasing with increasing Bi₂O₃ content. The ZnO content had the opposite effect to the Bi₂O₃ content. It appears that Bi³⁺ acts as a glass-modifier in this quaternary system.     

Liquid–liquid phase separation in sodium borosilicate glass: Ordering phenomena in particle arrangement

A structure of 13.9Na₂O · 36.0B₂O₃ · 50.1SiO₂ glass heat-treated at 610 °C for 5 h (glass G1) and 10 h (glass G2) was studied by stereological method on the basis of electron microscopy data obtained from plane sections of samples. It has been found that liquid phase separation in the course of heat treatment leads to formation of spherical particles with the volume fractions 0.047 (G1) and 0.065 (G2). It is argued that the stage of growth takes place in the glass G1 and the Ostwald ripening stage occurs in the glass G2. The analyses of pair correlation functions of particle traces on a secant plane indicate elements of ordering in mutual arrangement of particles for the both glasses G1 and G2. This conclusion is confirmed by results of numerical simulation. The experimental data on the pair correlation functions are in agreement with the results of calculations presented in the literature. It is noted that the ordering elements in mutual arrangement of particles play a key role in light scattering and other physical properties of material.     

Na2CaSi2O6–P2O5 based bioactive glasses. Part 1: Elasticity and structure

The glass structure and elastic properties of two bioglasses having bulk compositions near Na₂CaSi₂O₆ (45S5.2) and Na₂CaSi₃O₈ (55S4.1) were studied using both Raman and Brillouin scattering techniques. The annealed 45S5.2 glass has more Q² and Q⁰ but less Q³ species than 55S4.1 glass due to lower (Si⁴⁺ + P⁵⁺)/(Na⁺ + Ca²⁺) ratio. Brillouin scattering measurements of the as-annealed glasses indicated that 45S5.2 glass is ca. 2% and 9% higher in Young’s and bulk moduli than 55S4.1 glass due to more modifiers in the 45S5.2 glass. Nearly full crystallization of 45S5.2 glass was observed after treating it at 715 °C for ca. 30 min. Devitrification of the 45S5.2 glass caused an increase in the elastic moduli up to ca. 30% (fully crystallized) but a negligible change in density. This 45S5.2-derived crystalline phase displayed at least 17 Raman bands, and has the average elastic moduli of 72.4 (bulk), 41.6 (shear), and 104.7 (Young’s) GPa. The comparable elastic moduli with hydroxyapatite and the ability for developing a HCA layer in simulated body fluid indicate that the 45S5.2-derived phase may be better for using as a substitute of bone than its parent glass.     

Properties and structure of (1 − x)Li2O–xNa2O–Al2O3–4SiO2 glass systems

(1 − x)Li₂O–xNa₂O–Al₂O₃–4SiO₂ glasses were studied for the progressive percentage substitution of Na₂O for Li₂O at the constant mole of Al₂O₃ and SiO₂. The crystallization temperature at the exothermic peak increased from 898 to 939 °C when the Na₂O content increases from 0 to 0.6 mol. The coefficient of thermal expansion and density of these as-quenched glasses increase from 6.54 × 10⁻⁶ °C⁻¹ to 10.1 × 10⁻⁶ °C⁻¹ and 2.378 g cm⁻³ to 2.533 g cm⁻³ when the Na₂O content increases from 0 to 0.4 mol, respectively. The electrical resistivity has a maximum value at Na₂O · (Li₂O + Na₂O)⁻¹ = 0.4. The activation energy of crystallization decreases from 444 to 284 kJ mol⁻¹ when the Na₂O content increased from 0 to 0.4 mol. Moreover, the activation energy increases from 284 kJ mol⁻¹ to 446 kJ mol⁻¹ when the Na₂O content increased from 0.4 to 0.6 mol. The FT-IR spectra show that the symmetric stretching mode of the SiO₄ tetrahedra (1035–1054 cm⁻¹) and AlO₄ octahedra (713–763 cm⁻¹) exhibiting that the network structure is built by SiO₄ tetrahedra and AlO₄.     

Ultra-high thermal expansion glass–ceramics in the system MgO/Al2O3/TiO2/ZrO2/SiO2 by volume crystallization of cristobalite

Glasses in the system MgO/Al₂O₃/TiO₂/ZrO₂/SiO₂ with and without the addition of As₂O₃ and Sb₂O₃ were thermally treated. Up to a temperature of 950 °C, this resulted in the formation of ZrTiO₄, sapphirine and high quartz solid solution. Annealing at higher temperatures led to the formation of low quartz solid solutions, ZrTiO₄ and sapphirine. This resulted in a continuous increase of density, hardness, fracture toughness and thermal expansivity. In the glass doped with As₂O₅ and Sb₂O₅ annealing temperatures >1000 °C resulted in the formation of cristobalite instead of quartz. Then the density, hardness and strength decreased again, while the fracture toughness (up to 2.8 MPa m^1/2) and the thermal expansion coefficient increased strongly. In the dilatometric curves, a steep increase in expansion is observed in the temperature range from 100 to 200 °C, which is attributed to the transformation of low cristobalite to high cristobalite. The mean linear thermal expansion coefficient (25–200 °C) is 20 × 10^?6 K^?1 and the largest up to now reported in the literature for alkali-free silicate glass–ceramics.     

Sodium tracer diffusion in sodium boroaluminosilicate glasses

Sodium tracer diffusion coefficients, D*_Na, have been measured using the radioactive isotope Na-22 in sodium boroaluminosilicate (NBAS) glasses containing either a small amount of As₂O₃ or Fe₂O₃. The chemical compositions of the first type of glasses are given by the formula [(Na₂O)_0.71(Fe₂O₃)_0.05(B₂O₃)_0.24]_0.2[(SiO₂)_x(Al₂O₃)_1 ? x]_0.8 and those of the second type of glasses correspond to the formula [(Na₂O)_0.73(B₂O₃)_0.24(As₂O₃)_0.03]_0.18[(SiO₂)_x(Al₂O₃)_1 ? x]_0.82. Tracer diffusion measurements were performed at different temperatures between 198 and 350 °C. Pre-annealing of the glass samples at their glass transition temperatures in common air was found to lead to changes in the values of sodium tracer diffusion coefficients. For the NBAS glasses containing Fe₂O₃, after pre-annealing for 5 h, the activation enthalpy derived for the sodium tracer diffusion increases almost linearly from 57.5 to 71.3 kJ/mol with a decrease in the alumina content while the pre-exponential factor of the sodium tracer diffusion coefficient increases from 2.1 · 10^? 4 to 5.3 · 10^? 4 cm²/s. For the iron-free NBAS glasses pre-annealed for 5 h, the activation enthalpy varies between 63.9 and 71.4 kJ/mol while the pre-exponential factor varies between 1.5 · 10^? 4 and 1.2 · 10^? 3 cm²/s. In addition, it was observed that the considered glasses take up water when annealed at 300 °C in wet air with P_H2O = 474 mbar.     

Effect of TiO2 addition on the chemical durability of Bi2O3–SiO2–ZnO–B2O3 glass system

The effect of the substitution of ZnO for TiO₂ on the chemical durability of Bi₂O₃–SiO₂–ZnO–B₂O₃ glass coatings in hot acidic medium (0.1 N H₂SO₄ at 80 °C) for different times was studied. The thick films produced by a screen-printing method and heat treated at 700 °C/5 min were analyzed by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy. The glass from the Bi₂O₃–SiO₂–ZnO–B₂O₃ system developed Zn₂SiO₄ and a glassy phase that were readily attacked by hot 0.1 N sulfuric acid, whereas the heat treated coating from the Bi₂O₃–SiO₂–TiO₂–ZnO–B₂O₃ system presented a finer microstructure with thin interconnected Bi₄Ti₃O₁₂ crystals and a glassy phase more resistant to hot 0.1 N sulfuric acid attack etching.