Glasses in the system of MnNbOF5–BaF2–BiF3–ErF3

The glasses in the MnNbOF₅–BaF₂–5BiF₃–ErF₃ system were obtained and their thermal and optical properties were studied. The specialties of crystallization depending on system composition are showed. The glass structure is discussed based on results of the IR and Raman spectra study. During the studies of inelastic light scattering, there revealed a strong photoluminescence, produced by erbium emission, whose intensity depends not only on the erbium trifluoride content in glass, but also on the glass network structure.     

Effect of TiO2 addition on the chemical durability of Bi2O3–SiO2–ZnO–B2O3 glass system

The effect of the substitution of ZnO for TiO₂ on the chemical durability of Bi₂O₃–SiO₂–ZnO–B₂O₃ glass coatings in hot acidic medium (0.1 N H₂SO₄ at 80 °C) for different times was studied. The thick films produced by a screen-printing method and heat treated at 700 °C/5 min were analyzed by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy. The glass from the Bi₂O₃–SiO₂–ZnO–B₂O₃ system developed Zn₂SiO₄ and a glassy phase that were readily attacked by hot 0.1 N sulfuric acid, whereas the heat treated coating from the Bi₂O₃–SiO₂–TiO₂–ZnO–B₂O₃ system presented a finer microstructure with thin interconnected Bi₄Ti₃O₁₂ crystals and a glassy phase more resistant to hot 0.1 N sulfuric acid attack etching.     

Influence of Bi2O3 content on the crystallization behavior of TeO2–Bi2O3–ZnO glass system

Glass ceramic materials with composition 75TeO₂–xBi₂O₃–(25-x)ZnO (x = 13, 12, 11) possessing transparency in the near- and mid-infrared (MIR) regions were studied in this paper. It was found that as the Bi₂O₃ content increased in the glass composition, the observed crystallization tendency is enhanced, and high crystal concentrations were obtained for the glasses with high Bi₂O₃ content while maintaining transparency in the MIR region. Crystal size in the glass ceramic was reduced by adjusting the heat treatment conditions; the smallest average size obtained in this study is 700 nm. Bi_0.864Te_0.136O_1.568 was identified using X-ray Diffraction (XRD) and found to be the only crystal phase developed in the glass ceramics when the treatment temperature was fixed at 335 °C. The morphology of the crystals was studied using Scanning Electron Microscopy (SEM), and crystals were found to be polyhedral structures with uniform sizes and a narrow size distribution for a fixed heat treatment regime. Infrared absorption spectra of the resulting glass ceramics were studied. The glass ceramic retained transparency in the infrared region when the crystals inside were smaller than 1 μm, with an absorption coefficient less than 0.5/cm in the infrared region from 1.25 to 2.5 μm. The mechanical properties were also improved after crystallization; the Vickers Hardness value of the glass ceramic increased by 10% relative to the base glass.     

Magnetite nanoparticles prepared by the crystallization of Na2O–Fe2O3–B2O3–SiO2 glasses

A glass with the composition of 35Na₂O–24Fe₂O₃–20B₂O₃–20SiO₂–1ZnO (mol%) was melted, quenched, using a twin roller technique, and subsequently heat treated in the range 485–750 °C for 1–2 h. This led to the crystallization of magnetite as the sole or the major crystalline phase.Heat treatment at lower temperatures resulted in the crystallization of magnetite crystals 7–20 nm in diameter, whereas heat treatment at higher temperatures produced higher quantities of magnetite and much larger crystals. The room temperature magnetization and coercive force values were in the range of 6–57 emu g^? 1 and 0–120 Oe, respectively for the heat treated glasses.     

The Electron Diffraction Investigation of the Phase Structures in the Systems MF2–RF3 (CaF2–ErF3, SrF2–LaF3)

Crystallography Reports - The electron diffraction investigation of two-component phases in the systems MF2–RF3 (CaF2–ErF3, SrF2–LaF3) and components of the systems CaF2, SrF2,...     

Microstructure and thermal properties of the GeS2–In2S3–CsI glassy system

A new series of chalcohalide glasses in the GeS₂–In₂S₃–CsI pseudo-ternary system were prepared by conventional melt-quenching method. The glass-forming region was determined and it is mainly situated in the GeS₂-rich domain. The glasses have relatively high glass transition temperatures (T_g ranges from 335 to 405 °C) and good thermal stabilities. Based on the Raman spectra, it can be speculated that the glassy net is mainly constituted by [GeS₄] and [InS_4?xI_x] tetrahedra, which are interconnected by the bridging sulfur atoms. And the ethane-liked structural units [S₃Ge–GeS₃] can be formed because of the lacking of sulfur. Cs⁺ ion, which was added from CsI, exists as the nearest neighbor of I^? ion.     

Thermal expansion of glasses in the As2Se3–AsI3 system

Thermal expansion coefficients (α) of glasses in the As₂Se₃–AsI₃ system are measured in the glass transition region and temperature dependence of the fictive temperature is calculated on the basis of relaxation model. It is found that the increase of AsI₃ content results in: an increase of α, decrease of the glass transition temperature (T_g), increase of the α change at T_g, an effect of quenching rate on α, and also changes in the structural relaxation times spectrum. The data are discussed within the framework of the assumption that the addition of AsI₃ to As₂Se₃ results in: (1) destruction of the As₂Se₃ glass network, (2) structural inhomogeneity of the glasses increase, (3) the temperature dependence of chemical–structural equilibria occurring in the liquid state increases.     

Thermal properties of chalcogenide glasses in the GeSe2–As2Se3–CdSe system

In the present work, thermal properties of GeSe₂–As₂Se₃–CdSe glasses were investigated via DSC measurements. The dependences of glass transition temperature and thermal stability on glass composition were discussed. XRD measurement was also performed to validate the effect of cadmium on the thermal properties of glasses. The calculated Avrami exponent was used to demonstrate the three-dimensional growth of crystals in the glass matrices. The crystallization kinetics for the glasses was studied by using the modified Kissinger and Ozawa equations.     

EXAFS study of the Er3+ ion coordination in SiO2–TiO2–HfO2 sol–gel films

The local order around ion-implanted Er³⁺ ions in SiO₂–TiO₂–HfO₂ thin films prepared by sol–gel, was studied by extended X-ray absorption fine structure at the Er-L_III edge. Both the first and second coordination shells of Er³⁺ were analyzed for different heat-treatments. While the first coordination shell always consisted of ～6–7 oxygen atoms at distances varying between 2.23 and 2.27 Å, the structure of the second shell was found to vary with the film composition and heat-treatment. Namely, whereas Si was found to be the only second neighbor of erbium in binary SiO₂–TiO₂ films, the addition of HfO₂ caused a preferential replacement of Si by Hf. The post-implantation thermal treatments also played a fundamental role in determining the final environment of the erbium ions.     

Preparation and properties of chalcogenide glasses in the GeS2–Sb2S3–CdS system

In searching for new kind of photoelectric material, chalcogenide glasses in the GeS₂–Sb₂S₃–CdS system have been studied and their glass-forming region was determined. The system has a relatively large glass-forming region that is mainly situated along the GeS₂–Sb₂S₃ binary side. Thermal, optical and mechanical properties of the glasses were reported and the effects of compositional change on their properties are discussed. These novel chalcogenide glasses have relatively high glass transition temperatures (T_g ranges from 566 to 583 K), good thermal stabilities (the maximum of deference between the onset crystallization temperature, T_c, and T_g is 105 K), broad transmission region (0.57–12 μm) and large densities (d ranges from 2.99 to 3.34 g cm^?3). These glasses would be expected to be used in the field of rare earth doped fiber amplifiers and nonlinear optical devices.     

Effect of alumina on the structure and properties of Li2O–B2O3–P2O5 glasses

The structure of glasses within the system Li₂O–Al₂O₃–B₂O₃–P₂O₅ has been studied through ³¹P, ¹¹B and ²⁷Al Nuclear Magnetic Resonance, and the effect of Al₂O₃ substitution by B₂O₃ and P₂O₅ network formers on the structure and properties investigated for a constant Li₂O content. Multinuclear NMR results reveal that substitution of Al₂O₃ for B₂O₃ and P₂O₅ network formers in a glass with composition 50Li₂O·15B₂O₃·35P₂O₅ produces a change in boron environment from four-fold to three-fold coordination. Meanwhile aluminum can be present in four-, five- and six-fold coordinations a higher amount of Al(IV) groups is found for increasing alumina contents. The behavior of the glass transition temperature and electrical conductivity of the glasses has been interpreted as a function of the structural changes induced in the glass network when alumina is substituted for B₂O₃, P₂O₅ or both. Small additions of alumina produce a drastic increase in glass transition temperature, while it does not change for [Al₂O₃] greater than 3 mol.%. However, the electrical conductivity shows very different behavior depending on the type of substitution; it can remain constant when B₂O₃ content decreases or sharply decrease when P₂O₅ is substituted by Al₂O₃, which is attributed to a higher amount of BO₃ and phase separation.     

Molecular dynamics simulation for the rapid solidification process of MgO–Al2O3–SiO2 glass–ceramics

A molecular dynamics simulation method was used to study the effects of the microstructure on the solidification process of different cooling rates in the MgO–Al₂O₃–SiO₂ glass–ceramics with cordierite as the main crystalline phase. The reasons for changes in the microstructure during the solidification process were analysed by the radial distribution function curve, the bond angular distribution, the coordination number and the volume changes. The results showed that the cooling rate greatly affected the crystallisation process and the glass transition process. When the cooling rate was too fast, the atoms could not undergo a massive displacement before they were “frozen”, and the ability of atoms to achieve an equilibrium position was limited. Some amorphous phases were formed as a result of the disorder of the atomic arrangement, then some crystalline phase precipitated from the vitreous, and a glass–ceramic material was eventually formed.     

Nitridation of SiO2–B2O3 aerogels

SiO₂–B₂O₃ aerogels have been prepared by drying wet gels at a supercritical condition for ethanol in an autoclave. Aerogels have been nitrided for 6 h in flowing ammonia at the temperature of 1200 °C. It has been found that the amount of nitrogen incorporated in these aerogels always exceeds 20 wt%. This is a much higher value compared with the amount of nitrogen incorporated in a pure silica aerogel nitrided at the same conditions. The specific surface area of SiO₂–B₂O₃ aerogels has been between 312 and 359 m²/g. After nitridation some shrinkage of aerogels has been observed and the surface area decreases about 20%. In FTIR spectra of SiO₂–B₂O₃ aerogels a typical bands for SiO₂ are observed. After nitridation a shift and broadening of 1100 cm^?1 band to lower wavenumbers indicates that Si–N and B–N bonds are formed in nitrided aerogels.     

Growth of Fluorite Solid Solution Crystals in the Ternary SrF2–BaF2–LaF3 System and Investigation of Their Properties

Crystallography Reports - A series of three-component isostructural fluorite crystals (Sr1–xBax)0.7La0.3F2.3 (sp. gr. $$Fm{\bar {3}}m$$ , 0 ≤ x ≤ 1), the compositions of...     

Effect of V2O5 addition on the crystallisation of glasses belonging to the CaO–ZrO2–SiO2 system

The crystallisation of CaO–ZrO₂–SiO₂ glasses doped with V₂O₅ (0.1–5 mol%) has been investigated in terms of microstructure and thermal parameters. Results indicate that crystallisation is predominantly controlled by a surface nucleation mechanism, even though a partial bulk nucleation has been encountered in compositions containing more than 2 mol% of doping oxide. As detected from differential thermal analysis curves, glass transition temperature and crystallisation temperature, are strongly dependent upon V₂O₅ content varying from 0.0 to 2.0 mol%, while the crystallisation activation energy values decrease with a parabolic trend from B-glass (0.0 mol% V₂O₅ content, 495±7) to V-0.7 (0.7 mol% V₂O₅ content, 420±6) composition, increasing again to 442±5 kJ/mol K with higher amount of V₂O₅. The microstructure of the glass-ceramic materials clearly showed a marked dependence upon the amount of V₂O₅, also due to the presence of phase separation for content higher than 0.7 mol%. Wollastonite, CaO·SiO₂, and a calcia–zirconia–silicate, 2CaO·4SiO₂·ZrO₂, are the main crystalline phases whose ratio slightly varies with vanadium oxide content. The glass ceramics obtained from the studied materials are greenish and bluish coloured, so it is possible to use the studied glasses as coloured frits for tile glazes.     

Structure and properties of NaPO3–ZnO–Nb2O5–Al2O3 glasses

In an effort to design low-melting, durable, transparent glasses, two series of glasses have been prepared in the NaPO₃–ZnO–Nb₂O₅–Al₂O₃ system with ZnO/Nb₂O₅ ratio of 2 and 1. The addition of ZnO and Nb₂O₅ to the sodium aluminophosphate matrix yields a linear increase of properties such as glass transition temperature, density, refractive index and elastic moduli. The chemical durability is also significantly, but nonlinearly, improved. The glass with the highest niobium concentration, 55NaPO₃–20ZnO–20Nb₂O₅–5Al₂O₃ was found to have a dissolution rate of 4.5 × 10^? 8 g cm^? 2 min^? 1, comparable to window glass. Structural models of the glasses were developed using Raman spectroscopy and nuclear magnetic resonance spectroscopy, and the models were correlated with the compositional dependence of the properties.     

Surface modification and crystallization of the BaO–B2O3–SiO2 glassy system using CO2 laser irradiation

The surface modification and crystallization process of BaO–B₂O₃–SiO₂ glass compositions when exposed to CO₂ laser irradiation was evaluated as a function of the laser power, irradiation time and surface condition. The glass surface was modified by the application of laser power exceeding 0.40 W and an irradiation time of more than 300 s. Micro-Raman and X-ray diffraction measurements revealed at high laser power the formation of β-BaB₂O₄ (β-BBO) crystalline phase. The crystallization of the irradiated region was enhanced when β-BBO micrometer sized particles were dispersed on the surface of the glass sample. The intensity of the second harmonic generation observed in the crystallized region was found to depend mainly on the condition of the glassy surface prior to glass irradiation.     

Composition analysis of glasses in the PbBr2–PbCl2–PbF2–PbO–P2O5 system

Composition change during the melting process of some glasses in the PbBr₂–PbCl₂–PbF₂–PbO–P₂O₅ system melted at 450–470°C for 15 min was studied. Results show that there was a remarkable difference between the batch composition and the analyzed composition. Large amount of P, Br, Pb, and Cl were lost mainly in the form of PbBr₂, PbCl₂ and P₂O₅. The content of O is influenced by two factors. The incomplete decomposition of NH₄H₂PO₄ or the reaction between P₂O₅ and H₂O in the atmosphere increases the content of O, while the volatilization of P₂O₅ decreases the content of O.     

Formation of Co2+-doped nanocrystals in La2O3–MgO–Al2O3–SiO2 glass-ceramics

Transparent glass-ceramics were synthesized by heat-treatment of glass with a composition of 5La₂O₃–13.2MgO–28.8Al₂O₃–46SiO₂–4.5TiO₂–2.5ZrO₂–0.15CoO (LMAS) (wt.%). The activation energy of crystallization and the Avrami parameter for the LMAS glass were determined from the DTA curves at different heating rates. The most two intense bands of Raman spectrum of initial glass at ~ 810 cm^?1 and ~ 900 cm^?1 were connected with the presence of [SiO₄] and [TiO₄] tetrahedral, respectively. After heat-treated at 700 °C/10 h+820 °C/8 h, the intensity of the band for [TiO₄] tetrahedral weakened, while an intensive band at ~ 800 cm^?1 for the Ti–O bond appeared. Other bands were characteristics of high-silicate network and x(MgTi₂O₅)·y(Al₂TiO₅) polycrystals. The changes reflected phase separation after heat-treatment of the initial glass. The strong absorption band of glass-ceramics centered at 580 nm can be assigned to ⁴A₂(⁴F)→⁴T₁(⁴P) and the broad absorption band at 1100–1700 nm to ⁴A₂(⁴F)→⁴T₁(⁴F) transitions of tetrahedral coordinated Co²⁺ ion. Two broad emission bands, one was around 660 nm, the other was from 800 nm to 1050 nm, of glass-ceramics correspond to the ⁴T₁(⁴P)→⁴A₂(⁴F) and ⁴T₁(⁴P)→⁴T₂(⁴F) transitions of tetrahedral coordinated Co²⁺ ions. The absorption and emission features clearly demonstrated that Co²⁺ ions were incorporated into nanocrystals and located in tetrahedral sites.     

Spectroscopic properties of Co2+ ions in La2O3–MgO–Al2O3–SiO2 glass-ceramics

Co²⁺-doped La₂O₃–MgO–Al₂O₃–SiO₂ (LMAS) glass-ceramics was synthesized by conventional method. The microstructure of LMAS GCs heat-treated at 760 °C/12 h + 930 °C/4 h was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The spectroscopic properties of Co²⁺-doped LMAS GCs were studied by absorption spectrum, excitation spectrum, and temperature dependent luminescence spectra. XRD results revealed the sizes of MgAl₂O₄ crystalline phases are about 9.1 ± 1.5 nm. The three peaks in the visible absorption band of LMAS GCs at 549 nm, 585 nm and 626 nm are connected with the transitions from ⁴A₂ level to ²A₁/²T₂(²G), ⁴T₁(⁴P) and ²E/²T₁(²G) levels, respectively, and excitations into them emit the radiation at around 666 nm. The luminescence intensity increased with temperature increasing from 10 K to 150 K, while it weakened with temperature increasing from 150 K to 350 K. These features were explained by the effects of two competing mechanisms.