(Liquid + liquid) equilibria for ternary mixtures of (methanol or ethanol + toluene or m-xylene + n-dodecane)

(Liquid + liquid) equilibrium (LLE) results for the ternary mixtures of (methanol or ethanol + toluene or m-xylene + n-dodecane) at three temperatures (298.15, 303.15 and 313.15) K are reported. The compositions of liquid phases at equilibrium were determined by g.l.c. measurements and the results were correlated with the UNIQUAC and NRTL activity coefficient models. The partition coefficients and the selectivity factor of methanol and ethanol are calculated and compared to suggest which alcohol is more suitable for extracting the aromatic hydrocarbons (toluene or m-xylene) from n-dodecane. The phase diagrams for the ternary mixtures including both the experimental and correlated tie lines are presented. From the phase diagrams and the selectivity factors it is concluded that methanol has a higher efficiency as a solvent in extraction of aromatic hydrocarbon from alkane mixtures.     

Dynamic viscosities of the ternary liquid mixtures (dimethyl carbonate + methanol + ethanol) and (dimethyl carbonate + methanol + hexane) at several temperatures

Densities, ρ speeds of sound, u and dynamic viscosities, η of the ternary mixtures {dimethyl carbonate (DMC) + methanol + ethanol} and (dimethyl carbonate + methanol + hexane) were gathered at T = (293.15, 298.15, 308.15, and 313.15) K. From experimental data viscosity deviations, Δη of the ternary mixtures were evaluated. These results have been correlated using the Cibulka equation. The fitting parameters and the standard deviations of the ternary viscosity deviations are given. UNIFAC-VISCO group contribution method was used to predict the dynamic viscosities of the ternary mixtures at several temperatures.     

Excess volumes of mixing in (N,N-dimethylacetamide + methanol + water) and (N,N-dimethylacetamide + ethanol + water) at the temperature 313.15 K

Precise excess volumes of mixing measurements at T = 313.15 K are reported over the whole composition range for binary mixtures: (N,N-dimethylacetamide + water), (N,N-dimethylacetamide + methanol), (N,N-dimethylacetamide + ethanol) and for the ternary mixtures (N,N-dimethylacetamide + methanol + water) and (N,N-dimethylacetamide + ethanol + water). For all the systems, large negative deviations from ideality are observed. The binary results have been fitted using the Redlich–Kister type polynomial. The possibility of predicting the ternary results from the binary ones was examined.     

Measurement and prediction of (solid + liquid) equilibrium for sulfur compounds with aliphatic hydrocarbons

(Solid + liquid) equilibrium (SLE) of thiophene or diethylsulfide with n-heptane, n-octane or n-dodecane mixtures was measured by a static method. All the systems under study are simple eutectic systems. The DISQUAC group contribution model is fairly successful in predicting SLE.     

Temperature dependence on mutual solubility of binary (methanol + limonene) mixture and (liquid + liquid) equilibria of ternary (methanol + ethanol + limonene) mixture

Mutual solubility data of the binary (methanol + limonene) mixture at the temperatures ranging from 288.15 K close to upper critical solution temperature, and ternary (liquid + liquid) equilibrium (tie-lines) of the (methanol + ethanol + limonene) mixture at the temperatures (288.15, 298.15, and 308.15) K have been obtained. The experimental results have been represented accurately in terms of the extended and modified UNIQUAC models with binary parameters, compared with the UNIQUAC model. The temperature dependence of binary and ternary (liquid + liquid) equilibrium for the binary (methanol + limonene) and ternary (methanol + ethanol + limonene) mixtures could be calculated successfully using the extended and modified UNIQUAC model.     

Experimental and theoretical study of quaternary (liquid + liquid) equilibria for mixtures of (methanol or water + ethanol + toluene + n-decane)

Experimental (liquid + liquid) equilibrium data were obtained for the extraction of toluene from n-decane by mixed-solvents (ethanol + water) and (ethanol + methanol) at three temperatures (298.15, 303.15, and 313.15) K and ambient pressure.The measured tie-line data for two quaternary mixtures of {(ethanol +  water) + toluene + n-decane} and {(ethanol + methanol) + toluene + n-decane} are presented. The experimental quaternary (liquid + liquid) equilibrium data have been correlated using the NRTL activity coefficient model to obtain the binary interaction parameters of these components. The NRTL models predict the equilibrium compositions of the quaternary mixtures with small deviations. The partition coefficients and the selectivity factor of the mixed-solvents used were calculated and presented. From our experimental and calculated results, we conclude that for the extraction of toluene from n-decane mixtures the mixed-solvent (ethanol + methanol) has a higher selectivity factor than the other mixed-solvent at the three temperatures studied.     

Quaternary liquid–liquid equilibria for systems of {(water + methanol or ethanol) + m-xylene + n-dodecane}

Liquid–liquid equilibrium (LLE) data were determined for the quaternary systems of {(water + methanol or ethanol) + m-xylene + n-dodecane} at three temperatures 298.15, 303.15 and 313.15 K and atmospheric pressure. The composition of liquid phases at equilibrium was determined by gas–liquid chromatography and the results were correlated with the UNIQUAC and NRTL activity coefficient models. The partition coefficients and the selectivity factor of the solvent are calculated and compared. The phase diagrams for the quaternary systems including both the experimental and correlated tie lines are presented.     

(Liquid + liquid) extraction of methanol from alkanes using dialkylphosphate-based ionic liquids as solvents

In this work, the feasibility of ionic liquids (ILs), 1,3-dimethylimidazolium dimethylphosphate ([MMIM][DMP]), 1-ethyl-3-methylimidazolium diethylphosphate ([EMIM][DEP]), and 1-butyl-3-methylimidazolium dibutylphosphate ([BMIM][DBP]), as solvents for the extraction of methanol from its mixtures with hexane and heptane was analyzed. The knowledge of (liquid + liquid) equilibria (LLE) of these mixtures is necessary for the design of the extraction separation process. Hence, the LLE data for the ternary systems, {methanol + hexane + ([MMIM][DMP], or [EMIM][DEP], or [BMIM][DBP])}, and {methanol + heptane + ([MMIM][DMP], or [EMIM][DEP], or [BMIM][DBP])}, were measured at T = 298.2 K and atmospheric pressure. The experimental results were correlated with the thermodynamic nonrandom two-liquid (NRTL) model. The solute distribution ratios of methanol and methanol/alkane selectivities, derived from the experimental LLE data, were calculated and analyzed to evaluate the capability of the studied ILs to accomplish the separation target. Meanwhile, these capabilities were also compared with that of other ILs obtained from the literature.     

Measurements and modeling of quaternary (liquid + liquid) equilibria for mixtures of (methanol or ethanol + water + toluene + n-dodecane)

The extraction of aromatic compound toluene from alkane, dodecane, by mixed solvents (water + methanol), (water + ethanol) and (methanol + ethanol) have been studied by (liquid + liquid) equilibrium (LLE) measurements at three temperatures (298.15, 303.15, and 313.15) K and ambient pressure. The compositions of liquid phases at equilibrium were determined by gas liquid chromatography.The experimental tie-line data for three quaternary mixtures of {(water + methanol) + toluene + dodecane}, {(water + ethanol) + toluene + dodecane}, and {(methanol + ethanol) + toluene + dodecane} are presented. The experimental quaternary LLE data have been satisfactorily correlated by using the UNIQUAC and NRTL activity coefficient models. The parameters of the models have been evaluated and presented. The tie-line data of the studied quaternary mixtures also were correlated using the Hand method. The partition coefficients and the selectivity factor of solvent are calculated and compared for the three mixed solvents.The comparisons indicate that the selectivity factor for mixed solvent (methanol + ethanol) is higher than the other two mixed solvents at the three studied temperatures. However, considering the temperature variations of partition coefficients of toluene in two liquid phases at equilibrium, an optimum temperature may be obtained for an efficient extraction of toluene from dodecane by the mixed solvents.     

Measurements and modeling of LLE and HE for (methanol + 2,4,4-trimethyl-1-pentene), and LLE for (water + methanol + 2,4,4-trimethyl-1-pentene)

Excess enthalpy (H^E) for the binary system of (methanol + 2,4,4-trimethyl-1-pentene) (TMP-1) is reported at T = 298.15 K and 101 kPa. (Liquid + liquid) equilibrium (LLE) for the same system is measured at atmospheric pressure (101 kPa). LLE for ternary system of (water + methanol + 2,4,4-trimethyl-1-pentene) is measured at T = (283 and 298) K.The parameters of Non-Random Two-Liquid (NRTL) model were regressed for the system of (methanol + TMP-1) using H^E and LLE from this work combined with isobaric (101 kPa) and isothermal (T = 331 K) VLE data from literature. The NRTL parameters for the binary system of (water + TMP-1) were fitted to a binary LLE data set from literature. NRTL parameters for the binary system of (water + methanol) were taken from ASPEN PLUS. The LLE for the ternary system was modeled by the three binary NRTL interaction parameters systems. The binary and ternary models were compared against the measured data.     

Phase behavior of (CO2 + methanol + lauric acid) system

In this study the phase equilibrium behaviors of the binary system (CO₂ + lauric acid) and the ternary system (CO₂ + methanol + lauric acid) were determined. The static synthetic method, using a variable-volume view cell, was employed to obtain the experimental data in the temperature range of (293 to 343) K and pressures up to 24 MPa. The mole fractions of carbon dioxide were varied according to the systems as follows: (0.7524 to 0.9955) for the binary system (CO₂ + lauric acid); (0.4616 to 0.9895) for the ternary system (CO₂ + methanol + lauric acid) with a methanol to lauric acid molar ratio of (2:1); and (0.3414 to 0.9182) for the system (CO₂ + methanol + lauric acid) with a methanol to lauric acid molar ratio of (6:1). For these systems (vapor + liquid), (liquid + liquid), (vapor + liquid + liquid), and (solid + fluid) transitions were observed. The phase equilibrium data obtained for the systems were modeled using the Peng–Robinson equation of state with the classical van der Waals mixing rule with a satisfactory correlation between experimental and calculated values.     

Study of activity coefficients for sodium iodide in (methanol + benzene) system by (vapour + liquid) equilibrium measurements

By measuring the (vapour + liquid) equilibrium of {methanol (1) + benzene (2) + NaI} and testing the data using the ternary Gibbs–Duhem equation, the experimental results of the (vapour + liquid) equilibrium with thermodynamic consistency are obtained. It is supposed that the mean activity coefficients of NaI in (methanol + benzene) mixed solvents may be represented by a power series of salt concentration (m^1/2). Each parameter of the series was then obtained from the experimental results by the method of least squares. The calculated results show that the activity coefficients of NaI in (methanol + benzene) system with constant composition either decrease as the concentration increases, or decrease at first, then pass through a minimum and increase gradually again. This method is applicable to the determination of electrolytic activity coefficients in mixed non-aqueous solvents.     

Measurements and modeling for the density of 2-methoxy-2,4,4-trimethylpentane,HE for (methanol + 2-methoxy-2,4,4-trimethylpentane), LLE for (water + 2-methoxy-2,4,4-trimethylpentane) and LLE for (water + methanol + 2-methoxy-2,4,4-trimethylpentane)

Oxygenates are used in gasoline to increase the octane number and reduce carbon monoxide emission. 2-methoxy-2,4,4-trimethylpentane (TOME) is a tertiary ether which can potentially be used in addition with current oxygenates. This compound can be produced by etherification of diisobutylene with methanol. During the etherification, water is formed due to the dehydration of methanol. The appearance of water can cause (liquid + liquid) phase split in the production process. In this work, several physical properties of systems containing water, methanol and TOME are studied for the first time. The liquid density of 2-methoxy-2,4,4-trimethylpentane is presented from T = (298.15 to 408.16) K. Excess enthalpies are reported for the binary system of (methanol + 2-methoxy-2,4,4-trimethylpentane) at (T = 298.15 K). The (liquid + liquid) equilibrium (LLE) for (water + 2-methoxy-2,4,4-trimethylpentane) from T = (283.15 to 318.15) K is determined. The LLE is also reported for the ternary system of (water + methanol + 2-methoxy-2,4,4-trimethylpentane) at T = (283.15 and 298.15) K. The UNIQUAC parameters were regressed to model VLE, excess enthalpy and LLE for the binary and ternary data with one set of parameters.     

(Liquid + liquid) equilibria for ternary mixtures of (ethylene glycol + toluene + n-octane)

Tie-line data for ternary systems of (ethylene glycol + toluene + n-octane) at three temperatures (295.15, 301.15, and 307.15) K are reported. The compositions of liquid phases at equilibrium were determined and the results were correlated with the UNIQUAC and NRTL activity coefficient models. The partition coefficients and the selectivity factor of ethylene glycol are calculated and compared to suggest which ethylene glycol is more suitable for extracting of toluene from n-octane. The phase diagrams for the studied ternary mixtures including both the experimental and correlated tie lines are presented. From the phase diagrams and the selectivity factors, it is concluded that ethylene glycol may be used as a suitable solvent in extraction of toluene from n-octane mixtures.     

Excess properties of the binary mixtures of methylcyclohexane + alkanes (C6 to C12) at T = 298.15 K to T = 308.15 K

Experimental values of density, viscosity, and refractive index at T = (298.15, 303.15, and 308.15) K while the speed of sound at T = 298.15 K in the binary mixtures of methylcyclohexane with n-hexane, n-heptane, n-octane, n-nonane, n-decane, n-dodecane, and iso-octane are presented over the entire mole fraction range of the binary mixtures. Using these data, excess molar volume, deviations in viscosity, molar refraction, speed of sound, and isentropic compressibility are calculated. All the computed quantities are fitted to Redlich and Kister equation to derive the coefficients and estimate the standard error values. Such a study on model calculations in addition to presentation of experimental data on binary mixtures are useful to understand the mixing behaviour of liquids in terms of molecular interactions and orientational order–disorder effects.     

(Liquid + liquid) equilibria of (sulfolane + benzene + n-hexane), (N-formylmorpholine + benzene + n-hexane), and (sulfolane + N-formylmorpholine + benzene + n-hexane) at temperatures ranging from (298.15 to 318.15) K: Experimental results and correlation

The experimental (liquid + liquid) equilibrium (LLE) properties for two ternary systems containing (N-formylmorpholine + benzene + n-hexane), (sulfolane + benzene + n-hexane) and a quaternary mixed solvent system (sulfolane + N-formylmorpholine + benzene + n-hexane) were measured at temperature ranging from (298.15 to 318.15) K and at an atmospheric pressure. The experimental distribution coefficients and selectivity factors are presented to evaluate the efficiency of the solvents for extraction of benzene from n-hexane. The LLE results obtained indicate that increasing temperature decreases selectivity for all solvents. The LLE results for the systems studied were used to obtain binary interaction parameters in the UNIQUAC model by minimizing the root mean square deviations (RMSD) between the experimental and calculated results. Using the interaction parameters obtained, the phase equilibria in the systems were calculated and plotted. The calculated compositions based on the UNIQUAC model were found to be in good agreement with the experimental values. The result of the RMSD obtained by comparing the calculated and experimental two-phase compositions is 0.0163 for (N-formylmorpholine + benzene + n-hexane) system and is 0.0120 for (sulfolane + benzene + n-hexane) system.     

Quaternary (liquid + liquid) equilibria for (methanol + 2,2,4-trimethylpentane + toluene + 1,1-dimethylpropyl methyl ether or 1,1-dimethylethyl methyl ether) at T = 298.15 K

The experimental equilibrium tie-lines of two quaternary mixtures for (methanol + 1,1-dimethylpropyl methyl ether + toluene + 2,2,4-trimethylpentane) and (methanol + 1,1-dimethylethyl methyl ether + toluene + 2,2,4-trimethylpentane) were measured at the temperature 298.15 K and ambient pressure. The quaternary experimental results and their constituent ternaries have been satisfactorily predicted using binary parameters alone obtained by an associated-solution model that takes into account association of methanol molecules and solvation between (methanol + polar molecules) with allowance for a non-polar interaction given by an extended form of the UNIQUAC model. The results are further compared with those correlated by modified and extended forms of the UNIQUAC models that include multi-body interaction parameters in addition to binary ones.     

Experimental and predicted excess molar enthalpies for 1,4-dioxane + octane + cyclohexane at 303.15 K

Excess molar enthalpies for the ternary system 1,4-dioxane (1) + n-octane (2) + cyclohexane (3) and for the three constituent binary systems have been measured by a Calvet microcalorimeter at 303.15 K and ambient pressure. The experimental binary results were fitted by the Redlich–Kister equation. The excess molar enthalpies of the ternary system were correlated using the Cibulka equation. The DISQUAC group contribution model was applied to predict the excess molar enthalpy for this mixture.     

Experimental (vapour + liquid) equilibrium data of (methanol + water), (water + glycerol) and (methanol + glycerol) systems at atmospheric and sub-atmospheric pressures

Experimental (vapour + liquid) equilibrium results for the binary systems, (methanol + water) at the local atmospheric pressure of 95.3 kPa and at sub-atmospheric pressures of (15.19, 29.38, 42.66, 56.03, and 67.38) kPa, (water + glycerol) system at pressures (14.19, 29.38, 41.54, 54.72, 63.84, and 95.3) kPa and the (methanol + glycerol) system at pressures (32.02 and 45.3) kPa were obtained over the entire composition range using a Sweitoslwasky-type ebulliometer. The relationship of the liquid composition (x₁) as a function of temperature (T) was found to be well represented by the Wilson model. Computed vapour phase mole fractions, activity coefficients and the measured values along with optimum Wilson parameters are presented.     

Isobaric (vapour + liquid + liquid) equilibrium data for (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) systems at 100 kPa

Isobaric (vapour + liquid + liquid) equilibria were measured for the (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) system at 100 kPa.The apparatus used for the determination of (vapour + liquid + liquid) equilibrium data was an all-glass dynamic recirculating still with an ultrasonic homogenizer couple to the boiling flask.The experimental data demonstrated the existence of a heterogeneous ternary azeotrope for both ternary systems. The (vapour + liquid + liquid) equilibria data were found to be thermodynamically consistent for both systems.The experimental data were compared with the estimation using UNIQUAC and NRTL models and the prediction of UNIFAC model.