Spectral broadening and electron–photon coupling in III–V infrared detectors of low dimensional quantum confined system

Present work explores the mid-IR photodetection mechanism in III–V quantum confined system in twofold ways. Firstly, it models the extent of spectral linewidth broadening of photo-detector. Secondly, it investigates whether a strong perturbation of light can modulate the electronic bandstructure. Photo-absorption mechanism in the detector correlated to reduced carrier lifetime in ground state leading to homogeneous spectral widening is calculated. Besides, contribution of non-uniform size and composition of quantum dots towards spectral broadening is modeled in order to get the envelop of inhomogeneously broadened photocurrent spectrum. Our model generates photocurrent spectrum with 1.4 μm broadening centered at 3.5 μm at 77 K for a DWELL-IP, which agrees with the experimental result. The calculated photocurrent spectral width of 1.3 μm for GaAs/AlGaAs Quantum Well (QW) centered at 8.31 μm at 77 K also supports experimental data. In addition, our calculation reveals the emergence of a broad resonant peak in the spectrum of QW-IP in far infrared region (20–50 μm) as the photon volume density increases up to 0.1% of carrier density inside the active region. We introduce a hybrid density-of-states for strongly coupled electron–photon system to explain both mid and far IR peak.     

Heat affected zone in aluminum single crystals submitted to femtosecond laser irradiations

An experimental procedure is developed to quantify the radial dimension of the heat affected zone (HAZ) in metals submitted to laser pulses. A cube oriented aluminum single crystal is highly deformed by plane strain compression, then micro-drilled by 200 fs or 8 ns laser pulses, and finally analyzed by the electron back scattering diffraction technique. Recrystallized and recovered zones are observed as signatures of the HAZ. A typical value of 1.5 μm is found in the femtosecond regime of illumination, whereas for nanosecond pulses a value of 25 μm is measured. These results are in accordance with previous experiments and numerical simulations.     

Efficient femtosecond Yb:YAG laser pumped by a single-mode laser diode

Single-mode diodes enable a particularly simple, compact and effective pumping of solid-state laser devices for many specialized applications. We investigated a single-mode, 300-mW laser diode for pumping at 935 nm a Yb:YAG laser passively mode-locked by a semiconductor saturable absorber. Relatively short pulse generation (156 fs), tunable across 1033–1059 nm has been demonstrated. An optical-to-optical efficiency of about 28% has been obtained with 320 fs long pulses. Therefore, contrarily to what previously believed, compact diode-pumped ultrafast Yb:YAG oscillators can reliably and efficiently deliver pulses in the range of ≈ 100–200 fs with few tens of mW, which are very appealing for bio-diagnostics and amplifier seeding applications.     

Modeling and simulation of mid-IR amplifying characteristics of Tm3+-doped chalcogenide Photonic Crystal Fibers

This paper deals with the designing of a Tm³⁺-doped chalcogenide Photonic Crystal Fiber (PCF) amplifier operating in the mid-IR range. The chalcogenide glass of 72GeS₂–18Ga₂S₃–10CsI (in mol%) was fabricated with the high temperature melt-quenching method, which exhibited a strong emission peak around 3.8 μm under the excitation of a 800 nm laser. By employing the rate equations and propagation equations, the amplifying characteristics of the designed PCF amplifier were worked out. It is shown that the designed PCF amplifier exhibits a signal gain larger than 30 dB and a spectral width wider than 200 nm. The theoretical models and simulation results show that the PCF presented in this work can be used in developing high efficiency mid-IR light sources.     

Picosecond molecular switch based on the influence of photogenerated electric fields on optical charge transfer transitions

A concept for a picosecond molecular switch is demonstrated using a photoinduced electron transfer reaction in a covalently linked, fixed distance donor–acceptor molecule D–A linked to a perylene-3,4-dicarboximide chromophore, C. The chromophore C possesses a strong charge transfer transition in its optical spectrum. Selective excitation of C within D–A–C using 530 nm, 130 fs laser pulses produces^1 * C, which undergoes singlet–singlet energy transfer to produce^1 * D, which in turn transfers an electron to A. If the D–A–C system is selectively excited with 416 nm, 130 fs laser pulses to produce D ⁺ – A ⁻ –C prior to excitation of C with 530 nm, 130 fs laser pulses, a 25% lower yield of^1 * C is generated. The intense local electric field produced by D ⁺ – A ⁻ causes a 15 nm electrochromic red shift of the charge transfer absorption of C. Thus, the absorption of C at 530 nm is significantly diminished by the presence of D ⁺ – A ⁻ . The need to use two laser pulses with different wavelengths to observe these effects, and the resulting picosecond time response makes it possible to consider applications of this concept in the design of molecular switches.     

A phase stable short pulse generator using a DPMZM and phase modulators for application in 160 GBaud DQPSK systems

A method of 40 GHz phase stable short pulses generation is experimentally demonstrated. It is based on a dual parallel Mach–Zehnder modulator (DPMZM) driven by only one electrical sinusoidal clock and two cascaded phase modulators. The generated pulses are characterized with full-width-at-half-maximum pulse width of 1.9 ps, extinction ratio of 27 dB, timing jitter of 36 fs and signal to noise ratio over 30 dB. The high quality and phase stability of the pulses are further experimentally verified in a 4 × 40 GBaud differential quadrature phase shift keying (DQPSK) optical-time-division-multiplexing (OTDM) system.     

Effects of thickness of β-barium borate and angle of non-collinearity on the fs pulse generation by optical parametric amplification

Non-collinear optical parametric amplifiers (NOPAs) are used for the generation of tunable femtosecond pulses. The spectra of the uncompressed output from a lab-built NOPA in the 470–650 nm range have been recorded. Theoretical simulations for the effect of the length of the β-barium borate (BBO) crystal as well as the non-collinear angles between the pump and seed wavelengths have been carried out. For these we have obtained the initial experimental data from a 2 mm-thick BBO crystal when pumped with the second harmonic of the Ti:sapphire laser pulses of 100 fs duration. The pulse splitting length (PSL) and the group velocity mismatch (GVM) have been considered in simulations of the output. It was found that the crystal length of 1.3 mm and the crystal tilt of approximately 3.7° are optimal for the generation of pulses of ～11 fs at 600 nm.     

Spectral characteristics of polymer micro-fiber MZI near 1550 nm

The authors have produced the polymer micro-fiber with a highly optical conductive efficiency of 83% and 89% for the pump light of 532 nm and 1550 nm, respectively. The authors constructed a Mach–Zehnder Interferometer (MZI) by a micro-manipulation method and measured the different interference spectra by micro-adjusting the path difference of the dual interference arms of MZI under a microscope. Due to the path difference, the coherent length of the corresponding spectrum continuously and slightly decreases from 20 μm, 13.5 μm, 10.6 μm to 8 μm. The relationships between this particular MZI structure and the surrounding temperature, as well as the refractive index changes can be determined via the evanescent field and the thermally induced expansion or contraction effect, which will be reflected in the interference spectrum.     

High efficiency antireflection coating in MWIR region (3.6–4.9 μm) simultaneously effective for Germanium and Silicon optics

Antireflection coatings have critical importance in thermal imaging system working in MWIR region (3–5 μm) since optics of high refractive index materials are used. Germanium (Ge) and Silicon (Si) optics are used extensively in the MWIR thermal systems. In this paper a study has been carried out on the design and fabrication of multi-substrate antireflection coating effective for Germanium and Silicon optics in MWIR (3.6–4.9 μm) region. The wave band 3.6–4.9 μm is chosen for the reported work because detector system used in MWIR region has a band selection filter effective in the same wavelength region and atmospheric transmission window in MWIR region is effective in 3–5 μm spectral band. Comprehensive search method was used to design the multilayer stack on the substrate. The coating materials used in the design were Germanium (Ge), Hafnium oxide (HfO₂) and Y-Ba-Fluoride (IR-F625). The fabrication of coating was made in a coating plant fitted with Cryo pump system and residual gas analyzer (RGA). The evaporation was carried out at high vacuum (2–6 × 10^?6 mbar) with the help of electron beam gun system and layer thicknesses were measured with crystal monitor. The result achieved for the antireflection coating was 98.5% average transmission in 3.6–4.9 μm band for Germanium and Silicon optics. This work will be helpful in reducing the plant operation time, material and power consumption, as two different kinds of optics are simultaneously coated in a single coating cycle.     

Destruction of polylactic acid microcapsules under ultrasound irradiation

Hollow microcapsules have been considered for potential applications as drug or gene carriers. This paper describes an investigation into the mechanical properties of microcapsules with a biocompatible polylactic acid (PLA) shell that can be destroyed using ultrasound irradiation. The microcapsules had a radius of 1 to 25 μm and a shell thickness of 100 nm to 3 μm, and their response to ultrasound pulses with a center frequency of 700 kHz to 2 MHz was investigated. It was found that approximately 50% of capsules with a radius of 20 μm were destroyed using pulses with a pressure amplitude of 50 kPa and a frequency of 700 kHz, which is close to the resonance frequency of the capsules.     

2 μm passive Q-switched mode-locked Tm3+:YAP laser with single-walled carbon nanotube absorber

We report the first demonstration, to our knowledge, of passive Q-switched mode-locking in a Tm³⁺:YAP laser, operating in the 2 μm broadly spectral region formed with a compact Z-flod cavity. A transmission-type single-walled carbon nanotube saturable absorber (SWCNT–SA) is used for the initiation of the pulse generation. The repetition rate of the Q-switched envelope was 60 kHz at the pump power of 8.6 W. The mode-locked pulses inside the Q-switched pulse envelope had a repetition rate of ～92 MHz. A maximum average output power of 761 mW was obtained. The dependence of the operational parameters on the pump power was also investigated experimentally.     

Thorium free antireflection coating in MWIR region on Silicon optics

Most infrared transmitting optics have high refractive indices which in turn have high per surface reflection loss. So antireflection coating has very important role in increasing the transmission in the desired wavelength region. In this paper a study has been carried out on the design and fabrication of Thorium free antireflection coating effective for Silicon substrate in MWIR (3.6–4.9 μm) region. The wave band 3.6–4.9 μm is chosen for the reported work because the detected system used in MWIR region has a band selection filter effective in the same wavelength region. Comprehensive search method was used to design the multilayer stack on Silicon substrate. The coating materials used in the design were Germanium (Ge) and Silicon dioxide (SiO₂). The fabrication of coating was made in a coating plant fitted with Cryo pump system and Residual Gas Analyzer. The evaporation was carried out at high vacuum (2–6 × 10–6 mbar) using Electron Beam Gun and layer thicknesses were measured with crystal monitor. The result achieved for the antireflection coating was 96% average transmission in 3.6–4.9 μm band which withstood MIL-F-48616 environmental testing. This work provides an alternate antireflection coating on Silicon by replacing radioactive Thorium Fluoride, used as a coating material in most IR antireflection coating designs.     

Beam dynamics of 20 MeV MIRRORCLE-type tabletop storage ring

An experimental study on beam dynamics in MIRRORCLE-20, a tabletop storage ring of 15 cm orbit radius, was performed. Measurement of the infrared (IR) synchrotron light is the tool of this study. The IR emission is enhanced by a circular optics, named photon storage ring (PhSR), placed around the electron orbit, and is collected by a magic mirror associated with two plane mirrors in the storage ring. The measured average IR power in mid-IR region (λ < 50 μm) is ～59 mW. The observed stored beam current is about 1.2 A at maximum, which represents a record for a storage ring. The observed beam size is about 74 × 3 mm². We conclude that this very long beam size is due to the large betatron oscillation of 2/3 resonance injection.     

Semiconductor type single wall carbon nanotube absorber for passive mode-locked Nd:YVO4 laser

The pure semiconductor type single wall carbon nanotubes (SWCNT) was transferred on hydrophilic glass substrate to fabricate saturable absorbers by vertical evaporation technique. The recovery time of the absorber is 350 fs. The saturation intensity of the absorber was found to be 115 μJ/cm² at 1060 nm. The modulation depth of the absorber could be about 7%. Passive mode-locked Nd:YVO₄ laser using this kind of absorber was demonstrated. The largest average output power of the mode-locked laser is 1.4 W at the pump power of 7.8 W. The continuous wave mode-locked pulses with the repetition of 80 MHz were achieved.     

Experimental femtosecond laser photodisruption of rabbit sclera for minimally invasive laser sclerostomy: An in vitro study

Femtosecond laser technology, used as a minimally invasive tool in intrastromal refractive surgery, may also have potential as a useful instrument for glaucoma filtration surgery. The purpose of the present study was to evaluate the feasibility of minimally invasive laser sclerostomy by femtosecond laser photodisruption and seek the appropriate patterns of laser ablation and relevant laser parameters. A femtosecond laser (800 nm/50 fs/1 kHz), focused by a 0.1 numerical aperture (NA) objective lens, with different pulse energies and exposure times was applied to ablate hydrated rabbit sclera in vitro. The irradiated samples were examined by scanning electron microscopy (SEM). By moving a three-dimensional, computer-controlled translation stage to which the sample was attached, the femtosecond laser could produce three types of ablation patterns, including linear ablation, cylindrical aperture and rectangular cavity. With pulse energies ranging from 37.5 to 150 μJ, the linear lesions were consistently observed at the inner surface of sclera, whereas it failed to make any photodisruption if pulse energy was below the threshold value of 31.25 μJ, with the corresponding threshold intensity of 4.06×10¹⁴ W/cm². The depths of the linear lesions increased linearly with both pulse energy (37.5–150 μJ) and exposure time (0.1–0.4 s). Histological examination showed the incisions produced by femtosecond laser photodisruption had precise geometry and the edges were sharp and smooth, with no evidence of collateral damage to the surrounding tissue. Our results predict the potential application of femtosecond laser pulses in minimally invasive laser sclerostomy for glaucoma treatment.     

Infrared absorption cross sections for methanol

Infrared absorption cross sections for methanol, CH₃OH, have been determined near 3.4 and 10 μm from spectra recorded using a high-resolution FTIR spectrometer (Bruker IFS 125HR) and a multipass cell with a maximum optical path length of 19.3 m. Methanol/dry synthetic air mixtures were prepared and spectra were recorded at 0.015 cm^?1 resolution (calculated as 0.9/MOPD) at a number of temperatures and pressures (50–760 Torr and 204–296 K) appropriate for atmospheric conditions. Intensities were calibrated using composite methanol spectra taken from the Pacific Northwest National Laboratory (PNNL) IR database. The new measurements in the 10 μm region indicate problems with the existing methanol spectroscopic line parameters in the HITRAN database, which will impact the accuracy of satellite retrievals.     

High power Nd:YAG lasers operating at 1.3 μm wave band

The laser properties of 1.3 μm spectral region in Nd:YAG crystal and their simultaneous dual wavelength threshold condition are investigated. Three types of high power 1.3-μm Nd:YAG quasi continuous wave (QCW) lasers, which operate at 1.319 μm or 1.338 μm single wavelength, 1.319 μm and 1.338 μm simultaneous dual wavelength, are achieved with a maximum average output power of 138 W, 132 W and 120 W, respectively.     

Ultra-broad and flat supercontinuum generation in short photonic crystal fiber combined with conventional fibers

In order to gain ultra-broad and flat super-continuum (SC) spectrum, we propose and demonstrate a new scheme. By coupling a train of short pulses with 100 fs width and 16.2 mW average power generated by a mode-locked laser into the scheme – short photonic crystal fiber (PCF) combined with conventional fibers. The SC spectrum has 491 nm bandwidth at −15 dBm below the spectral peak with ±0.5 dBm uniformity 100 nm in only 0.45 m PCF. The spectral bandwidth generated in the scheme increases 292 nm than spectrum generated in the two conventional fibers, and increases 152 nm than spectrum generated in the three convention fibers.     

Phase-matched generation of high-order continuous-wave coherent Raman sidebands

We demonstrate the generation of continuous-wave (cw) Raman sidebands through phase-matched four-wave mixing (FWM) in molecular hydrogen. The phase-matching conditions of the intracavity FWM driven in our dispersion-compensated high-finesse cavity are satisfied over a 52.8 THz-wide frequency range (763.9–883.6 nm). This leads to the generation of high-order anti-Stokes emission. The cw Raman sidebands have sufficient bandwidth to allow the synthesis of a train of optical pulses with a duration of 13 fs at a repetition rate of 17.6 THz under phase-locked conditions.     

Spermatozoon of the freshwater rotifer Brachionus calyciflorus (Rotifera,Monogononta): Advances in morphological and ultrastructural studies

The morphological and ultrastructural features of the spermatozoon in Brachionus calyciflorus are described using light, fluorescence and transmission electron microscopy (TEM). The mature spermatozoon, which appears to be thread-like, is composed of a slightly expanded anterior of cell body region and a flagellum region without acrosome. The cell body region and flagellum region are respectively 16–27 μm and 20–33 μm in length (n = 60). The spermatozoon is characterized by a mass of dense tubular materials, which occupy most of the cell. Some mitochondria are distributed around the nuclear region in the anterior of the cell body region, while in the posterior portion of cell body, the chromatin often contains a single lobated nucleus arranged at the center of cell. The flagellum contains the classic axoneme (9 × 2 + 2) and possesses lateral undulating membrane. Mature B. calyciflorus males have no germ cell stages earlier than the spermatids in the testis. TEM examination reveals rigid rods as well as predominant typical spermatozoon in the testis. Observations, based on successive photographs and videos, enabled a first-time recording of the unique inverted movement of the spermatozoon, which indicated that the movement of the spermatozoon is driven by the flagellum. Our study also provides further supplementary insights into the phylogenetic systematics of the Rotifera.