1.55 μm silicon-based reflection-type waveguide-integrated thermo-optic 2 × 2 switch

In this work a waveguide-integrated 2 × 2 switch operating at the infrared communication wavelength of 1550 nm is proposed and theoretically discussed. The device is based on the total internal reflection (TIR) phenomenon and the thermo-optic effect (TOE) in hydrogenated amorphous silicon (a-Si:H) and crystalline silicon (c-Si). It takes advantage of a bandgap-engineered a-Si:H layer to explore the properties of an optical interface between materials showing similar refractive indexes but different thermo-optic coefficients. In particular, thanks to modern plasma-enhanced chemical vapour deposition (PECVD) techniques, the refractive index of the amorphous film can be properly tailored to match that of c-Si at a given temperature. TIR may be therefore achieved at the interface by acting on the temperature. The device is integrated in a 4 μm-wide and 3 μm-thick single-mode rib waveguide. The substrate is a silicon-on-insulator (SOI) wafer with an oxide thickness of 500 nm. We calculated an output crosstalk always better than 24 dB and insertion losses as low as 3.5 dB.     

4 × 10 Gb/s wavelength multicasting with tunable NRZ-to-RZ pulse format conversion using time- and wavelength-interleaved pulses

We demonstrate 4 × 10 Gb/s simultaneous wavelength multicasting and NRZ-to-RZ pulse format conversion with tunable duty cycle. Multicasting is achieved by four-wave mixing of the input signal with a time- and wavelength-interleaved laser source, while the format conversion is obtained through the use of a pulsed probe. The input data are copied to four multicast outputs with a common relative delay time. Error-free operations have been obtained in all the outputs with power penalties ranging from ? 0.5 to 0.5 dB. Output duty cycles with a tuning range of 4.3 ps have been achieved.     

Simulation of 16 × 10 Gb/s WDM system based on optical amplifiers at different transmission distance and dispersion

In this paper, the 16 channel WDM systems at 10 Gb/s have been investigated for the various optical amplifiers and hybrid optical amplifiers and the performance has been compared on the basis of transmission distance and dispersion. The amplifiers EDFA and SOA have been investigated independently and further compared with hybrid optical amplifiers like RAMAN-EDFA and RAMAN-SOA. It is observed that hybrid optical amplifier RAMAN-EDFA provides the highest output power (12.017 and 12.088 dBm) and least bit error rate (10^?40 and 9.08 × 10^?18) at 100 km for dispersion 2 ps/nm/km and 4 ps/nm/km respectively.     

Selective adsorption of coronene on Si(1 1 1)-(7 × 7)

The adsorption of coronene (C₂₄H₁₂) on the Si(1 1 1)-(7 × 7) surface is studied using scanning tunneling microscopy (STM). Upon room temperature submonolayer deposition, we find that the coronene molecules preferentially adsorb on the unfaulted half of the 7 × 7 unit cell. Molecules adsorbed on different sites can be induced to move to the preferential sites by the action of the tip in repeated image scans. Imaging of the molecules is strongly bias dependent, and also critically depends on the adsorption site. We analyze the results in terms of differential bonding strength for the different adsorption sites and we identify those substrate atoms which participate in the bonding with the molecule.     

Interaction of Ag with the Si(1 1 1)1 × 1–H surface

Synchrotron radiation based photoemission spectroscopy (SRPES) and low energy electron diffraction (LEED) are used to study the interaction between Ag atoms and the Si(1 1 1)1 × 1–H surface. At an Ag coverage of 0.063 monolayers (ML) on the Si(1 1 1)1 × 1–H surface, the Si 2p component corresponding to Si–H bonds decreases, and an additional Si 2p component appears which shifts to a lower binding energy by 109 meV with respect to the Si bulk peak. The new Si 2p component is also observed for 0.25 ML Ag on the Si(1 1 1)7 × 7 surface. These findings suggest that Ag atoms replace the H atoms of the Si(1 1 1)1 × 1–H surface and form direct Ag–Si bonds. Contrary to the widely accepted view that there is no chemical interaction between Ag particles and the H-passivated Si surface, these results are in good agreement with recent first-principles calculations.     

Coverage dependence of glycine adsorption on the Ge(100) − 2 × 1 surface

A combination of infrared spectroscopy, X-ray photoelectron spectroscopy and density functional theory has been used to investigate the adsorption behavior of glycine at the Ge(100) ? 2 × 1 surface under ultrahigh vacuum conditions. Comparison of experimental and simulated IR spectra indicates that at 310 K, glycine adsorbs on Ge(100) ? 2 × 1 via O–H dissociation, with some fraction of the products also forming an N dative bond to a neighboring germanium atom. O–Ge dative bonding is not observed. As coverage increases, the surface concentration of the monodentate O–H dissociated adduct increases, while that of the N dative-bonded species appears constant. XPS data support and clarify the IR findings and reveal new insights, including the presence at higher coverage of a minor product that has undergone dual O–H and N–H dissociation. These findings are supported by the calculated energy diagrams, which indicate that the reaction of a glycine molecule on the Ge(100) ? 2 × 1 surface via O–H dissociation and interdimer N dative bonding is both kinetically and thermodynamically favorable and that N–H dissociation of this adduct is feasible at room temperature given incomplete thermal accommodation along the reaction pathway.     

Atomic and nanostructures of monolayer c(2 × 2)NiN on Cu(0 0 1)

Structures of monolayer nickel nitride (NiN) on Cu(0 0 1) surface are studied by X-ray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED) and scanning tunneling microscopy (STM). Formations of Ni–N chemical bonds and NiN monolayer at the surface are confirmed by XPS on the N-adsorbed Cu(0 0 1) surfaces after Ni deposition and subsequent annealing to 670 K. A c(2 × 2) structure is always observed in the LEED patterns, which is a quite contrast to the (2 × 2)p4g structure observed usually at the N-adsorbed Ni(0 0 1) surface. Atomic images by STM indicate the mixture of Ni–N and Cu–N structures at the surface. Density of the trenches on the N-saturated surface decreases and the grid pattern on partially N-covered surfaces becomes disordered with increasing the Ni coverage. These results are attributed to the decrease of the surface compressive stress at the N-adsorbed Cu surface by mixing Ni atoms.     

Ga-induced restructuring of Si(5 5 12) − 2 × 1 reconstructed surface at room temperature

Motivated by the need to form 1D-nanostructured dopants on silicon surfaces, we have attempted to grow Ga on the high index Si(5 5 12) surface which has a highly trenched (1D) morphology. The evolution of the interface with Ga adsorption in the monolayer regime has been probed by in situ AES, LEED and EELS. Controlling the kinetics by changing the Ga flux rates shows an interesting difference in the 1.0 to 1.5 ML region. The low flux rate (0.03 ML/minute) results in a Frank van der Merwe (layer by layer) growth mode up to 2 ML, while the higher flux rate (0.1 ML/minute) shows a transient island formation after the completion of 1 ML. The low rate shows the formation of 2 × (3 3 7) and (2 2 5) superstructures, while only the 2 × (3 3 7) is observed in a wide coverage range for the higher rate. The results demonstrate the ability to kinetically control the surface phases with different electronic properties of this technologically important interface.     

Strained c(4 × 2) CoO(1 0 0)-like monolayer on Pd(1 0 0): Experiment and theory

We report on an interface-stabilized strained c(4 × 2) phase formed by cobalt oxide on Pd(1 0 0). The structural details and electronic properties of this oxide monolayer are elucidated by combination of scanning tunneling microscopy data, high resolution electron energy loss spectroscopy measurements and density functional theory. The c(4 × 2) periodicity is shown to arise from a rhombic array of Co vacancies, which form in a pseudomorphic CoO(1 0 0) monolayer to partially compensate for the compressive strain associated with the large lattice mismatch (～9.5%) between cobalt monoxide and the substrate. Deviation from the perfect 1:1 stoichiometry thus appears to offer a common and stable mechanism for strain release in Pd(1 0 0) supported monolayers of transition metal rocksalt monoxides of the first transition series, as very similar metal-deficient c(4 × 2) structures have been previously found for nickel and manganese oxides on the same substrate.     

Reversible and irreversible reactions of three oxygen precursors on InAs(0 0 1)-(4 × 2)/c(8 × 2)

The substrate reactions of three common oxygen sources for gate oxide deposition on the group III rich InAs(0 0 1)-(4 × 2)/c(8 × 2) surface are compared: water, hydrogen peroxide (HOOH), and isopropyl alcohol (IPA). Scanning tunneling microscopy reveals that surface atom displacement occurs in all cases, but via different mechanisms for each oxygen precursor. The reactions are examined as a function of post-deposition annealing temperature. Water reaction shows displacement of surface As atoms, but it does not fully oxidize the As; the reaction is reversed by high temperature (450 °C) annealing. Exposure to IPA and subsequent low-temperature annealing (100 °C) show the preferential reaction on the row features of InAs(0 0 1)-(4 × 2)/c(8 × 2), but higher temperature anneals result in permanent surface atom displacement/etching. Etching of the substrate is observed with HOOH exposure for all annealing temperatures. While nearly all oxidation reactions on group IV semiconductors are irreversible, the group III rich surface of InAs(0 0 1) shows that oxidation displacement reactions can be reversible at low temperature, thereby providing a mechanism of self-healing during oxidation reactions.     

1024 × 1024 Format pixel co-located simultaneously readable dual-band QWIP focal plane

This paper reports the first demonstration of the megapixel-simultaneously-readable and pixel-co-registered dual-band quantum well infrared photodetector (QWIP) focal plane array (FPA). The dual-band QWIP device was developed by stacking two multi-quantum-well stacks tuned to absorb two different infrared wavelengths. The full width at half maximum (FWHM) of the mid-wave infrared (MWIR) band extends from 4.4 to 5.1 μm and the FWHM of a long-wave infrared (LWIR) band extends from 7.8 to 8.8 μm. Dual-band QWIP detector arrays were hybridized with custom fabricated direct injection read out integrated circuits (ROICs) using the indium bump hybridization technique. The initial dual-band megapixel QWIP FPAs were cooled to 70 K operating temperature. The preliminary data taken from the first megapixel QWIP FPA has shown system NEΔT of 27 and 40 mK for MWIR and LWIR bands, respectively.     

An optical OFDM multiplexer and 16 × 10 Gb/s OOFDM system using serrodyne optical frequency translation based on LiNbO3 phase modulator

This paper proposes an all-optical orthogonal frequency division multiplexing (OFDM) multiplexer based on sawtooth wave driving LiNbO₃ phase modulators by using serrodyne optical frequency translation. This multiplexer has high integration ability. The designing concept and implementation method have been discussed. A 16 × 10 Gb/s optical OFDM system is designed based on this multiplexer. Transmission characteristics, including tolerances of polarization mode dispersion (PMD) and nonlinear impairments have been studied numerically. Simulations show that the PMD tolerance is about 42 ps. The spectral efficiency reaches 1 bit/s/Hz with binary modulation format.     

Adsorption of small molecules on a (2 × 1) PdZn surface alloy on Pd(1 1 1)

The adsorption of methanol, formaldehyde, methoxy, carbon monoxide and water on a (2 × 1) PdZn surface alloy on Pd(1 1 1) has been studied using DFT calculations. The most stable adsorption structures of all species have been investigated with respect to the structure and the electronic properties. It was found that methanol is only weakly bound to the surface. The adsorption energy only increases with higher methanol coverage, where chain structures with hydrogen bonds between the methanol molecules are formed. The highest adsorption energy was found for the formate species followed by the methoxy species. The formaldehyde species shows quite some electronic interaction with the surface, however the stable η₂ formaldehyde has only an adsorption energy of about 0.49 eV. The calculated IR spectra of the different species fit quite well to the experimental values available in the literature.     

H adsorption at Ag/Si interfaces in epitaxially grown Ag(1 1 1) films on Si(1 1 1)7 × 7 substrates

The interaction of atomic H with Ag(1 1 1)/Si(1 1 1)7 × 7 surfaces was studied by thermal desorption (TD) spectroscopy and scanning tunneling microscopy (STM) at room temperature. TD spectroscopy revealed an intense peak from mono H–Si bonds, even though the Si surface was covered by the Ag atoms. This peak was not observed from Ag-coated SiO₂/Si substrates. STM observation showed no clear change of the Ag surface morphology resulting from H exposure. All these results indicate that the atomic H adsorbs at neither the Ag surfaces nor Ag bulk sites, but at the Ag/Si interface by diffusing through the Ag film.     

Propagation characteristics of Gaussian beams through 2 × 2 square matrix circular apertures

Based on the expansion of the hard aperture function into a finite sum of complex Gaussian functions, using Collins formula, the approximate analytical expression of Gaussian beams through 2 × 2 square matrix circular apertures is derived. Finally, some numerical examples are given to illustrate the analytical results by Matlab. It is shown that the propagation characteristics is related with the propagation distance z, the radius of circular aperture a and the distance d. The results can be directly used in other beams and square matrix apertures, and be applied to control beams and optical system designing.     

SrTiO3(100) − √5 × √5 − R26.6 surface observed by high-resolution scanning tunneling microscopy

SrTiO₃(100) – (√5 × √5) – R26.6 surfaces were studied by means of high-resolution scanning tunneling microscopy (STM) under ultrahigh vacuum conditions. By varying the bias voltage in the occupied state, it was possible to observe the arrangement of titanium and oxygen atoms in the unit cells of a (√5 × √5) surface superstructure, which revealed that the TiO₂ layer is the terminating plane of the (√5 × √5) surface. In the STM images, peculiar protrusions were seen at the oxygen fourfold hollow site responsible for √5 × √5 periodicity. The protrusions are asymmetrical in contrast, which would be an important consideration in proposing accurate structural models for (√5 × √5) surface superstructures.     

Real time dynamics of Si magic clusters mediating phase transformation: Si(111)-(1 × 1) to (7 × 7) reconstruction revisited

Using Scanning Tunneling Microscope (STM), we show that the surface undergoes phase transformation from disordered “1 × 1” to (7 × 7) reconstruction which is mediated by the formation of Si magic clusters. Mono-disperse Si magic clusters of size ~ 13.5 ± 0.5 Å can be formed by heating the Si(111) surface to 1200 °C and quenching it to room temperature at cooling rates of at least 100 °C/min. The structure consists of 3 tetra-clusters of size ~ 4.5 ? similar to the Si magic clusters that were formed from Si adatoms deposited by Si solid source on Si(111)-(7 × 7) [1]. Using real time STM scanning to probe the surface at ~ 400 °C, we show that Si magic clusters pop up from the (1 × 1) surface and form spontaneously during the phase transformation. This is attributed to the difference in atomic density between “disordered 1 × 1” and (7 × 7) surface structures which lead to the release of excess Si atoms onto the surface as magic clusters.     

Second harmonic response of the Si(111)7 × 7 surface

Optical second harmonic generation spectra have been experimentally obtained from a clean Si(111) 7 × 7 in two different polarization configurations isolating the rotational anisotropic and isotropic contributions. The energy of the fundamental photon is varied from 0.8 eV to 2.5 eV. For comparison, we also use a microscopic formulation based on the semi-empirical tight binding method to evaluate the nonlinear surface susceptibility tensor χ(2ω). Good agreement between theory and experiment is obtained with respect to the number of resonances, their position in energy, and surface or bulk character.