Spectroscopic properties and ab initio calculations on the structure of erbium–zinc-borate glasses and glass ceramics

Glasses in the (Er₂O₃)_x·(B₂O₃)_(60 ? x)·(ZnO)₄₀ system (0 ≤ x ≤ 15 mol%) have been prepared by the melt quenching technique. X-ray diffraction, FTIR spectroscopy, UV-VIS spectroscopy and ab initio calculations studies have been employed to study the role of Er₂O₃ content on the structure of the investigated glass system.X-ray diffraction and infrared spectra of the glasses reveal that the B–O–B bonds may be broken with the creation of new non-bridging oxygen ions facilitating the formation of Er–O–B linkages. The excess of oxygen can be accommodated in the network by the conversion of sp² planar [BO₃] units to the more stable sp³ [BO₄] tetrahedral structural units. The linkages of the [BO₄] structural units can polymerize in [B₃O₉]^? 9 cyclic trimeric ions which will produce the ErBO₃ crystalline phase. An increase of the efficiency corresponding to the ⁴I_15/2 state to ⁴I_11/2 state (4f–4f) transitions of Er^+ 3 ions was observed for the erbium oxide richest glasses.Ab initio calculations on the structure of the matrix network show the thermodynamic instability of the [BO₄], [ZnO₄] and [Zn₄O] structural units. Formation of three-coordination oxygens was necessary to compensate shortage of oxygens from zinc ions.     

Electrooptical Kerr phenomenon and Raman spectroscopy of one lithium–niobium–silicate glass-forming system

Raman spectra and electrooptical Kerr coefficients of glasses belonging to one lithium–niobate–silicate glass-forming system xNb₂O₅ · (66 ? x)SiO₂ · 19Li₂O · 11K₂O · 2B₂O₃ · 2CdO are studied. It has been found that these glasses demonstrate a record value of electrooptical Kerr coefficient; the glass with x = 35 showed electrooptical Kerr coefficient equal to 266 × 10^?16 m/V². Using Raman spectroscopy combined with the concept of Constant Stoichiometric Groupings, a correlation of electrooptical Kerr coefficients of these glasses with the content of Li₂O · Nb₂O₅ (or 2LiNbO₃) groupings has been demonstrated. The hypothesis that electrooptical Kerr sensitivity of glasses is related to the ordered regions with composition and symmetry corresponding to some of known electrooptical crystals has been verified. These regions, which the authors called ‘Crystal Motifs’, are identified with the groupings found in studying Raman spectra of the glasses.     

Thermal conductivity of mixed alkali silicate glasses at low temperature

Thermal conductivity of glass is one of the fundamental properties of it. However, that has not been studied enough. That of only less than 20 compositions has been measured below the room temperature. In this study, we measured the thermal conductivity of xNa₂O · (100 ? x)SiO₂ and (33 ? y)Na₂O · yCs₂O · 67SiO₂ glasses by a transient heating method in the temperature range from about 150 K to room temperature. The conductivity of xNa₂O · (100 ? x)SiO₂ is found to decrease with the increase in alkali content. The dominant factor of this behavior is the decrease in phonon mean free path, which is due to the increase of non-bridge oxygen. Thermal conductivity of (33 ? y)Cs₂O · yNa₂O · 67SiO₂ is decreased with the increase in Cs₂O/(Na₂O + Cs₂O) ratio. The dominant factor of this behavior is the decrease of sound velocity. However, composition dependence of the phonon mean free path also affects the thermal conductivity. Phonon mean free path of 33Cs₂O · 67SiO₂ glass is longer than that of 33Na₂O · 67SiO₂ glass, and should be related to the change in distribution of structural unit in glass. In addition, phonon mean free path of mixed alkali glasses are shorter than that of single alkali glasses.     

EPR and magnetic susceptibility studies of B2O3–Bi2O3–Gd2O3 glasses

Glasses of the xGd₂O₃ · (100 − x)[B₂O₃ · Bi₂O₃] system with 0.5 ⩽ x ⩽ 10 mol% were studied by electron paramagnetic resonance (EPR) and magnetic susceptibility measurements. Data obtained show that for low gadolinium oxide contents of the samples (x ⩽ 3 mol%) the Gd³⁺ ions are randomly distributed in the host glass matrix and are present as isolated and dipole–dipole coupled species. For higher gadolinium oxide contents of the samples (x > 3 mol%) the Gd³⁺ ions appear as both isolated and antiferromagnetically coupled species. The EPR spectra of the glasses reveal resonance sites with an unexpected high crystalline field in addition to the ‘U’ spectrum, typical for Gd³⁺ ions in disordered systems. This absorption line is due to Gd³⁺ ions that replace Bi³⁺ ions from the host glass matrix and could play the network unconventional former role in the studied glasses.     

Structure and properties of the 70Li2S · (30 − x)P2S5 · xP2O5 oxysulfide glasses and glass–ceramics

The 70Li₂S · (30 ? x)P₂S₅ · xP₂O₅ (mol%) oxysulfide glasses were prepared by the melt quenching method. The glasses were prepared in the composition range 0 ≦ x ≦ 10. The glass–ceramics were prepared by heating the glasses over crystallization temperatures. The PO_nS_3?n (n = 1–3) oxysulfide units were produced in the glasses and glass–ceramics by partial substituting P₂O₅ for P₂S₅. In particular, the P₂OS₆^4? unit would be produced by substituting a small amount of P₂O₅ for P₂S₅. The oxygen atoms were incorporated into the Li₇P₃S₁₁ crystal structure because the diffraction peaks of the oxysulfide glass–ceramic shifted to the higher angle side. The glass–ceramic with 3 mol% of P₂O₅ exhibited the highest conductivity of 3.0 × 10^?3 S cm^?1 and the lowest activation energy for conduction of 16 kJ mol^?1. The P₂OS₆^4? dimer units in the oxygen-incorporated Li₇P₃S₁₁ crystal would improve conductive behavior of the Li₂S–P₂S₅ glass–ceramics.     

Synthesis and structure–property relations in xCuO–(1 − x)Bi2O3 (0.5 ⩽ x ⩽ 0.9) (C1–C5: x = 0.5, 0.6, 0.7, 0.8, 0.9) glasses

Synthesis of the xCuO–(1 ? x)Bi₂O₃ (0.5 ? x ? 0.9) (C1–C5: x = 0.5, 0.6, 0.7, 0.8, 0.9) glasses was done via nitrate–citrate gel route. Glassy phase is ascertained by XRD studies. Magnetic susceptibility results in the range 4.2–400 K show weak paramagnetic nature with exchange integrals ～0.024–0.13 eV in the glasses. The electron paramagnetic resonance (EPR) in the range 4.2–363 K shows g ≈ 2.0 and the trend of the g-matrix elements g_|| > g_⊥ > g_e for the glasses C1–C5 at 4.2 K are due to the Cu²⁺ (3d⁹) paramagnetic site in the glasses which is in a tetragonally elongated octahedron [O_1/2–CuO_4/2–O_1/2] having D_4h symmetry. IR spectroscopic results show the presence of octahedron [BiO_6/2]^3? and [CuO_6/2]^4? units and pyramidal [BiO_2/2O]^? unit in the glasses.     

Composition and structure dependence of the properties of lithium borophosphate glasses showing boron anomaly

This work presents a study on the structure, microstructure and properties of 50Li₂O·xB₂O₃·(50 ? x)P₂O₅ glasses. The structure has been studied through NMR spectroscopy and the microstructure by TEM. The properties of the glasses are discussed according to their structure and microstructural features. The introduction of boron produces new linkages between phosphate chains through P–O–B bonds, whose amount increases with boron incorporation; at the same time, a depolymerisation of the phosphate chains into Q¹-type phosphate units takes place. The introduction of boron produces an increase in T_g together with a decrease in the molar volume. The room temperature electrical conductivity increases with boron content as well. However, B₂O₃ contents higher than 20 mol% lead to crystallisation of lithium orthophosphate which contributed to hinder ionic conduction of the glasses.     

Spectral studies of Sm3+ and Dy3+ doped lithium cesium mixed alkali borate glasses

The effect of host glass composition on the optical absorption and fluorescence spectra of Sm³⁺ and Dy³⁺ has been studied in mixed alkali borate glasses of the type 67B₂O₃ · xLi₂O · (32 − x)Cs₂O (x = 8, 12, 16, 20 and 24). The Judd–Ofelt intensity parameters (Ω₂, Ω₄ and Ω₆) are calculated. The radiative transition probabilities (A), radiative lifetimes (τ_R), branching ratios (β) and integrated absorption cross-sections (Σ) are computed for certain excited states of Sm³⁺ and Dy³⁺ ions for different x values in the glass matrix. Stimulated emission cross-sections (σ_p) are obtained for certain emission transitions of two ions in these mixed alkali borate glasses. These parameters are compared for different x values in the glass matrix. Variation of these parameters with x in the glass matrix has been studied.     

Crystallization of barium magnesium phosphate glasses determined by differential thermal analysis and X-rays diffraction

The scope of this work is to determine the crystalline phases of devitrified barium magnesium phosphate glasses and the glass composition which presents the best resistance to crystallization. Barium magnesium phosphate glasses with composition xMgO · (1 ? x)(60P₂O₅ · 40BaO) mol% (x = 0, 0.15, 0.3, 0.4, 0.5, and 0.6) were analyzed by differential thermal analysis (DTA) to evaluate the thermal stability against crystallization, and X-ray diffraction (XRD) to identify the crystalline phases formed after devitrification. The glass transition temperature (T_g) increases as the MgO content increases. The maximum temperature attributed to the crystallization peak in the DTA curve (T_c) increases when x increases in the range 0 ? x ? 0.3, and it decreases for x > 0.3. The most thermally stable glass composition against crystallization is for x = 0.3. After the devitrification, the number of coexisting crystalline phases increases as the MgO content increases. For x = 0.3 there is the coexistence of γBa(PO₃)₂ and Ba₂MgP₄O₁₃ phases for devitrified glasses. The trend of the T_c is explained based on the assumptions of changes in the Mg²⁺ coordination number and the amphoterical features of MgO.     

Square-wave voltammetry and impedance spectroscopy in iron-doped melts of the system Li2O/Al2O3/SiO2

Glass melts with the basic compositions xLi₂O · 15Al₂O₃ · (85 − x)SiO₂ (x = 8.5, 11, 13.5, 16 and 18.5) doped with 0.25 mol% Fe₂O₃ were studied by square-wave voltammetry and impedance spectroscopy at temperatures in the range from 1100 to 1600 °C. The square-wave voltammograms show a pronounced peak attributed to the reduction of Fe³⁺ to Fe²⁺. The attributed peak potentials which are equal to the standard potentials of the redox pair decrease linearly with the temperature. Impedance spectra measured could be simulated using an equivalent circuit attributed to a simple electron transfer reaction controlled by diffusion.     

Structure and crystallization behavior of mixed potassium-lithium niobiosilicate glasses

Potassium-lithium niobiosilicate (KLiNS) glasses with a composition of (27 ? x)K₂O · xLi₂O · 27Nb₂O₅ · 46SiO₂ (x = 0, 3, 12 and 20) have been synthesized by a melt-quenching method. The glass structure and devitrification behavior have been studied by Raman spectroscopy, DTA, and XRD. By increasing the lithium content, less distorted niobium octahedra increase, indicating a niobium clustering. This change strongly affects the crystallization behavior. In the glasses x = 0 and x = 3, just above T_g, only nanocrystals of an unidentified phase are formed, while for x = 12 and x = 20 potassium lithium niobate (KLN) solid solutions with tetragonal tungsten–bronze structure crystallize by bulk nucleation. In these glasses, LiNbO₃ crystallizes at higher temperature by surface nuclei. Ultimately, it is possible to produce nanostructured glasses based on KLN nanocrystals, by partial replacement of K by Li.     

Square-wave voltammetry and impedance spectroscopy in tin doped melts with the compositions xNa2O · 15Al2O3 · (85 − x)SiO2 (x = 8.5, 11 and 16)

Glasses with the base compositions xNa₂O · 15Al₂O₃ · (85 ? x)SiO₂ (x = 8.5, 11 and 16) doped with 0.5 mol% SnO₂ were investigated by both square-wave voltammetry and impedance spectroscopy in the temperature range from 1300 to 1600 °C. Each recorded square-wave voltammogram exhibits a well pronounced peak attributed to the Sn²⁺/Sn⁴⁺-redox pair. Impedance spectra were measured in a frequency range from 0.1 to 10⁵ s^?1 as a function of the superimposed dc-potential and were simulated using an equivalent circuit taking into account the resistivity of the melt, the electrochemical double layer, a resistor attributed to a kinetically hindered electron transfer and a Warburg parameter which accounts for the diffusion process of Sn⁴⁺ and Sn²⁺ to and from the electrode. Additionally, two impedance elements, a resistor and a capacitance both attributed to adsorption processes were necessary to fit the impedance spectra.     

FTIR and UV–VIS spectroscopy investigations on the structure of the europium–lead–tellurate glasses

Glasses in the xEu₂O₃·(100-x)[4TeO₂·PbO₂] system where 0 ≤ x ≤ 50 mol% have been prepared using the melt quenching method. The influence of europium ions on the structure of lead–tellurate glasses has been investigated using density measurements, FTIR and UV–VIS spectroscopy. Structural changes produced by increasing the rare earth concentration were followed.The europium and lead ions show a preference towards [TeO₃] structural units causing a deformation of the TeOTe linkages. Structural changes inferred by analyzing the band shapes of IR spectra revealed that the increase of the Eu^+ 3 content causes the intercalation of [EuO_n] entities in the [TeO₄] chain network. The excess of oxygen can be supported into the glass network by the formation of [PbO_n] and [EuO_n] structural units.The UV–VIS spectroscopy data show that europium ions enter the glass matrix in the Eu²⁺ and Eu³⁺ valence states, the last being predominant in the studied glasses. The Pb^+ 2 ions produce strong absorption in the ultraviolet domain.     

Influence of europium ions on structure and crystallization properties of bismuth borate glasses and glass ceramics

Glasses of the xEu₂O₃ · (100?x)[2Bi₂O₃ · B₂O₃] system with 0 ? x ? 25 mol% have been characterized by X-ray diffraction and FTIR spectroscopy measurements. Melting at 1100 °C and the rapid cooling at room temperature permitted us to obtain glass samples. In order to improve the local order and to develop crystalline phases, the glass samples were kept at 625 °C for 24 h. After heat treatment two crystalline phases were put into evidence. One of the crystalline phases was observed for the host glass matrix, the x = 0 mol% sample, and belongs to the cubic system. The second one was observed for the x = 25 mol% sample and was find to be orthorhombic with two unit cell parameters very close to each other. For the samples with 0 < x < 25 mol% there is a mixture of the two mentioned phases. FTIR spectroscopy data suggest that both Bi₂O₃ and B₂O₃ play the glass network former role while the europium ions play the network modifier role in the studied glasses.     

Redox behavior and diffusion of copper in soda-lime-silica melts

Glasses with the base mol% composition xNa₂O · 10CaO · (90 ? x)SiO₂ with x = 10, 16, 20 and 26 were investigated at high temperatures using square-wave voltammetry. The recorded voltammograms exhibit two peaks. That at less negative or (depending on temperature and glass composition) even positive potential is attributed to the reduction of Cu²⁺ to Cu⁺, while that observed at more negative potential is caused by the reduction of Cu⁺ to metallic copper. For both redox steps, the peak potentials decrease linearly with temperature. Those of the composition with 10 mol% Na₂O show the most negative values. The diffusion coefficients can be fitted to Arrhenius equation. If referenced to the same viscosity, the diffusion coefficients decrease with increasing Na₂O-concentration. The effect of composition on the thermodynamics as well as on diffusivities is explained by the incorporation of the copper ions into the melt structure.     

Structure and properties of MoO3-containing zinc borophosphate glasses

ZnO–B₂O₃–P₂O₅ glasses doped with MoO₃ were investigated in the series (100?x)[0.5ZnO–0.1B₂O₃–0.4P₂O₅]–xMoO₃, where bulk glasses were obtained by slow cooling in air within the compositional region of 0 ? x ? 60 mol% MoO₃. The incorporation of MoO₃ into the parent zinc borophosphate glass results in a weakening of bond strength in the structural network, which induces a decrease in chemical durability and glass transition temperature. Raman spectra reflect the incorporation of molybdate groups into the glass network of the studied glasses by the presence of the polarized vibrational band at ≈976 cm^?1 ascribed to the MO_x symmetric stretching vibrations and the depolarized band at ≈878 cm^?1 ascribed to the Mo–O–Mo stretching vibration. The incorporation of molybdate units into the glass network results in the depolymerization of phosphate chains and the formation of P–O–Mo bonds, as reflected in Raman and ³¹P NMR spectra. According to the ¹¹B MAS NMR spectra, tetrahedral B(OP)_4?x(OMo)_x units are formed in the glasses, whereas only a small amount of BO₄ units is converted to BO₃ units in the MoO₃-rich glasses.     

Mixed transition-ion effect in the glass system: Fe2O3-MnO-TeO2

In earlier studies on phosphate and tellurite glasses containing vanadium and iron oxides, non-linear variation of physical properties as functions of the ratios of the transition ions (V/V + Fe) were observed. The most striking effect was observed with electrical conductivity, where a 3 orders of magnitude reduction in conductivity was observed at a V/V + Fe ratio of ~ 0.4. The effect was termed Mixed Transition-ion Effect or MTE. In phosphate glasses, however, MTE was not observed when one of the transition ions was manganese. It was concluded that Mn does not contribute to conduction in these glasses. In the present study, we demonstrate a mixed transition ion effect in tellurite glasses containing MnO and Fe₂O₃ (xFe₂O₃(0.2 ? x) MnO0.8TeO₂ with x varying from 0 to 0.2). A maximum in the property at an intermediate composition (x = 8.5 mol%), was observed in DC resistivity, activation energy, molar volume etc. Mossbauer and optical absorption (UV–VIS–NIR) measurements were performed on these glasses and the transport mechanism has been identified to be hopping of small polarons between Fe^3 + (Mn^3 +) and Fe^2 + (Mn^2 +) sites.     

Optical band gap and Raman spectra in some (Bi2O3)x(WO3)y(TeO2)100−x−y and (PbO)x(WO3)y(TeO2)100−x−y glasses

The glasses representing (Bi₂O₃)_x(WO₃)_y(TeO₂)_100?x?y and (PbO)_x(WO₃)_y(TeO₂)_100?x?y systems were prepared. The dilatometric glass-transition temperatures of examined glass samples were found in the region 383–434 °C, the coefficient of thermal expansion varied from 12 to 16 ppm/°C and the density ranged from 6.30₂ to 6.80₈ g/cm³. From the optical transmission measurements of thin glassy bulk samples prepared by a glass blowing, the optical gap values were found in the narrow region 3.21–3.36 eV. For the temperature interval 300–480 K, the values of the temperature coefficient of the optical band gap varied from 3.7 × 10^?4 to 5.24 × 10^?4 eV/K. It is suggested that Raman feature observed at around 350 cm^?1 can be assigned to an overlap of Raman bands attributed to WO₆ corner shared octahedra and to the following three atomic linkages: Bi–O–Te, Pb–O–Te and W–O–Te.     

Effect of OH− content on emission properties in Er3+-doped tellurite glasses

A series of tellurite glasses of composition, 75TeO₂–20ZnO–(5 ? x)La₂O₃–xEr₂O₃ (x = 0.05, 0.1, 0.3, 0.6, 1.0, 2.0, and 3.0 mol%) with different hydroxl content were prepared. The effect of Er³⁺ and OH^? groups concentration on the emission properties of Er³⁺: ⁴I_13/2 → ⁴I_15/2 transition in tellurite glasses was investigated. The constant K_OH–Er for Er³⁺ in tellurite glasses, which represents the strength of interaction between Er³⁺ and OH^? groups in the case of energy migration, was about 14 × 10^?19 cm⁴ s^?1. The interaction parameter C_Er,Er for the migration rate of Er³⁺: ⁴I_13/2 → ⁴I_13/2 transition in tellurite glass was 46 × 10^?40 cm², which indicates that concentration quenching in Er³⁺-doped modified tellurite glass for a given Er³⁺ concentration is much stronger than in silicate and phosphate glasses.     

The effect of fluoride on the Fe2+/Fe3+-redox equilibrium in glass melts in the system Na2O/NaF/CaO/Al2O3/SiO2

Liquids with the base compositions (16 − x/2)Na₂O · xNaF · 10CaO · 74SiO₂ (x = 0, 1, 3, and 4) and (10 − x/2) · Na₂O · xNaF · 10CaO · yAl₂O₃ · (80 − y)SiO₂ (x = 0, 1, 3, 5 and y = 5 and 15) doped with 0.25 mol% Fe₂O₃ were studied by means of square-wave voltammetry in the temperature range from 1000 to 1500 °C. With increasing temperature, the redox equilibria were shifted to the reduced state. Also while increasing the alumina concentration, the Fe²⁺/Fe³⁺-redox equilibrium is shifted to the reduced state. In the soda-lime–silica melt the addition of fluoride shifts the equilibrium to the oxidized state, while in the aluminosilicate melts with 15 mol% Al₂O₃, the equilibrium is shifted to the reduced state. In the aluminosilicate melts with 5 mol% Al₂O₃, the equilibrium was not affected by the fluoride concentration. This is explained by the structure of the respective glass compositions.