Influence of annealing temperature on optical properties of zinc oxide thin films analyzed by spectroscopic ellipsometry method

Zinc oxide (ZnO) thin films were sol–gel spin coated on glass substrates, annealed at various temperatures 300 °C, 400 °C and 500 °C and characterized by spectroscopic ellipsometry method. The optical properties of the films such as transmittance, refractive index, extinction coefficient, dielectric constant and optical band gap energy were determined from ellipsometric data recorded over the spectral range of 300–800 nm. The effect of annealing temperature in air on optical properties of the sol–gel derived ZnO thin films was studied. The transmission values of the annealed films were about 65% within the visible range. The optical band gap of the ZnO thin films were measured between 3.25 eV and 3.45 eV. Also the dispersion parameters such as single oscillator energy and dispersive energy were determined from the transmittance graph using the Wemple and DiDomenico model.     

Properties of Bi2O3 thin films prepared via a modified Pechini route

Thin bismuth oxide films have been prepared by a modified Pechini route on glass substrate and annealed at temperatures ranging between 400 °C and 700 °C using bismuth nitrate as raw material. The thin films were then characterized for structural, surface morphological, optical and electrical properties by means of X-ray diffraction (XRD), Atomic force microscopy (AFM), scanning electron microscopy (SEM), optical absorption and d.c. two-probe, respectively. Structural investigations indicated that as-prepared bismuth oxide films were polycrystalline and multiphase, and annealing temperatures played a key role in the composition and optical properties of these films. AFM and SEM images revealed well defined particles which are highly influenced by annealing temperatures. The optical studies showed a direct band gap which varied with annealing temperatures between 3.63 eV and 3.74 eV. The electrical measurement showed that the electrical resistivity increased with annealing temperatures and the films were typical semiconductors. As catalyst, bismuth oxide films annealed at 550 °C had the best photocatalytic performance for photodegradation of methyl orange.     

Optical constants and thermocoloration of pulsed laser deposited molybdenum oxide thin films

Molybdenum oxide thin films were prepared by pulsed laser deposition. The as-deposited films were dark. Annealing the films in air at 400 °C resulted in transparent films. These films were further annealed in vacuum at 300 and 400 °C to investigate thermocoloration. The structural, chemical, and optical properties of the films were determined. All films were predominantly amorphous. The air-annealed films were nearly stoichiometric. However, after annealing in vacuum at 400 °C, the films became oxygen-deficient. The transmittance of the films progressively decreased as the vacuum-annealing temperature increased, indicating stronger coloration of the films. The optical constants were determined from the transmittance measurements. Both the refractive index and extinction coefficient increased upon vacuum annealing. However, the band gap slightly decreased after vacuum annealing.     

Influence of surface topography and annealing temperature on the surface and volume of dissipation electrical energy and Spitzer–Fan model in Al doped ZnO films

The aim of this work is to investigate the optical constants of aluminum doped zinc oxide films annealed at different temperatures. With increasing temperature, due to decreasing unfilled inter-granular volume per unit thickness, the optical transmittance spectra of films were increased. The films have a normal dispersion in the spectral range 400?<?λ?<?500 nm and the anomalous dispersion in IR range. The lattice dielectric constants ε_L, the free charge carriers concentration, the plasma frequency, Spitzer–Fan model and the waste of electrical energy as heat of films can be analyzed using the refractive index n and the extinction coefficient k spectra. With increasing annealing temperature, the lattice dielectric constants ε_L of films decrease however the free charge carriers concentration of films increase. The free carrier electric susceptibility of films annealed at 600 °C has maximum value. The energy loss by the free charge carriers when traversing the bulk and surface of films annealed at 600 °C has a minimum value in the near fundamental absorption edge and it with increasing energy increases.     

Effect of thermal annealing on disorder and optical properties of Cr/Si bilayer thin films

Chromium/silicon bilayers are deposited by sequential electron beam evaporation on quartz substrates. The bilayers consisting of Cr and Si layers of 50 and 400 nm thicknesses, respectively, are subjected to post-deposition annealing at temperatures from 200 to 700 °C. The thermal annealing results in the interdiffusion between Cr and Si, as evidenced by cross-section scanning electron micrographs and the line profiles obtained from energy-dispersive X-ray spectroscopy. It is inferred from the compositional line profiles that the films are a combination of silicon-rich oxide, chromium oxide and unreacted Cr up to 500 °C. Chromium disilicide forms at temperatures greater than 500 °C with decrease in chromium oxide content. The refractive index value and extinction coefficient values are 2.1 and 0.12 in the as-deposited case which increase to 3.5 and 0.24 at 400 °C. These values decrease to 2.1 and 0.12 at 500 °C. At the same temperatures, the band gap values are 2.21, 2.40 and 2.28, respectively. Thus, the refractive index, absorption coefficient and the optical band gap of the films peak at an annealing temperature of 400 °C and decrease thereafter. Significantly, this is accompanied by increase in Urbach energy which is an indication of increase in disorder in the system. There is decrease in Urbach energy as well as the optical constants at temperatures >400 °C.     

Effects of thermally induced anatase-to-rutile phase transition in MOCVD-grown TiO2 films on structural and optical properties

Titanium dioxide (TiO₂) films with a thickness of 550 nm were deposited on quartz glass at 300 °C by metalorganic chemical vapor deposition. The effects of post-annealing between 600 °C and 1000 °C were investigated on the structural and optical properties of the films. X-ray diffraction patterns revealed that the anatase phase of as-grown TiO₂ films began to be transformed into rutile at the annealing temperature of 900 °C. The TiO₂ films were entirely changed to the rutile phase at 1000 °C. From scanning electron spectroscopy and atomic force microscopy images, it was confirmed that the microstructure of as-deposited films changed from narrow columnar grains into wide columnar ones. The surface composition of the TiO₂ films, which was analyzed by X-ray photoelectron spectroscopy data, was nearly constant although the films were annealed at different temperatures. When the annealing temperature increased, the transmittance of the films decreased, whereas the refractive index and the extinction coefficient calculated by the envelope method increased at high temperature. The values of optical band gap decreased from 3.5 eV to 3.25 eV at 900 °C. This abrupt decrease was consistent with the anatase-to-rutile phase transition. Received: 4 October 2000 / Accepted: 4 December 2000 / Published online: 23 May 2001     

Optoelectronics properties of TiO<Subscript>2</Subscript>:Cu thin films obtained by sol gel method

In this research, Cu-doped TiO₂ thin films have been successfully deposited onto a glass substrate by Sol–gel technique using dip coating method. The films were annealed at different annealing temperatures (400–500 °C) for 1 h. The structural, optical and electrical properties of the films were investigated and compared using X-ray Diffraction, UV–visible spectrophotometer and 4-point probe method. Optical analysis by mean transmittance T(λ) and absorption A(λ) measurements in the wavelength range between 300 to 800 nm allow us to determine the indirect band gap energy. DRX analysis of our thin films of TiO₂:Cu shows that the intensities of the line characteristic of anatase phase increasing in function of the temperature.     

Role of heat treatment on structural and optical properties of thermally evaporated Ga10Se81Pb9 chalcogenide thin films

Amorphous chalcogenides, based on Se, have become materials of commercial importance and were widely used for optical storage media. The present work deals with the structural and optical properties of Ga₁₀Se₈₁Pb₉ ternary chalcogenide glass prepared by melt quenching technique. The glass transition, crystallization and melting temperatures of the synthesized glass were measured by non-isothermal DSC measurements at a constant heating rate of 30 K/min. Thin films of thickness 4000 Å were prepared by thermal evaporation techniques on glass/Si (1 0 0) wafer substrate. These thin films were thermally annealed for two hours at three different annealing temperatures of 345, 360 and 375 K, which were in between the glass transition and crystallization temperatures of the Ga₁₀Se₈₁Pb₉ glass. The structural, morphological and optical properties of as-prepared and annealed thin films were studied. Analysis of the optical absorption data showed that the rules of the non-direct transitions predominate. It was also found that the optical band gap decreases while the absorption coefficient, refractive index and extinction coefficient increase with increasing the annealing temperature. Due to the higher values of absorption coefficient and annealing dependence of the optical band gap and optical constants, the investigated material could be used for optical storage.     

Effect of process parameters and post-deposition annealing on the microwave dielectric and optical properties of pulsed laser deposited Bi<Subscript>1.5</Subscript>Zn<Subscript>1.0</Subscript>Nb<Subscript>1.5</Subscript>O<Subscript>7</Subscript> thin films

Bismuth Zinc niobate (Bi_1.5Zn_1.0Nb_1.5O₇) thin films were deposited by pulsed laser deposition (PLD) method on fused silica substrates at different oxygen pressures. The structural, microwave dielectric and optical properties of these thin films were systematically studied for both the as-deposited and the annealed films at 600°C. The as-deposited films were all amorphous in nature but crystallized on annealing at 600°C in air. The surface morphology as studied by atomic force microscopy (AFM) reveals ultra-fine grains in the case of as-deposited thin films and cluster grain morphology on annealing. The as-deposited films exhibit refractive index in the range of 2.36–2.53 (at a wavelength of 750 nm) with an optical absorption edge value of 3.30–3.52 eV and a maximum dielectric constant of 11 at 12.15 GHz. On annealing the films at 600°C they crystallize to the cubic pyrochlore structure accompanied by an increase in band gap, refractive index and microwave dielectric constant.     

Photoluminescence study of Ce-doped silica films

Ce-doped silica films with different Ce concentrations were prepared by ion-beam sputtering and ion implantation. The films containing 1.2 at% Ce were annealed at temperatures from 500 °C to 1200 °C in air ambient, and were annealed in different ambient at 1100 °C. Ce-related photoluminescence was observed in films sensitive to the Ce concentrations, annealing temperatures and the annealing ambient. The peak intensity of the photoluminescence band is approximately linear with Ce concentrations. Also, the photoluminescence intensity is dependent on the annealing temperatures and reaches its highest value after annealing at 700 °C. In addition, the experimental results show that compared with the annealing in an air ambient, the photoluminescence intensity can be enhanced with nitrogen gas. There would be no obvious change for the photoluminescence position or shape.     

Nature of room-temperature ferromagnetism from undoped ZnO nanoparticles

ZnO nanoparticles were synthesized by a sol–gel calcination process following being annealed in air at 400, 600, 800 and 1000°C. X-ray diffraction pattern and X-ray photoelectron spectroscopy show that all the samples present a typical wurtzite structure and no other impurity phases are observed. Room-temperature ferromagnetism from all the samples is confirmed by the vibrating sample magnetometer measurements, which shows that the RTFM decreases with the annealing temperature increasing from 400 to 800°C, and then became larger for the sample annealed at 1000°C. According to the Raman scattering spectra and electron paramagnetic resonance, the RTFM of samples annealed at 600, 800 and 1000°C might be related to the oxygen vacancy related defects. However, the RTFM from the sample annealed at 400°C, presenting nearly the same value as that of the sample annealed at 1000°C, could originate with the interstitial zinc defects associated with XPS and photoluminescence analyses.     

XRD study on the effect of the deposition condition on pulsed laser deposition of ZnO films

Using a pulsed laser deposition (PLD) process on a ZnO target in an oxygen atmosphere, thin films of this material have been deposited on Si(111) substrates. An Nd: YAG pulsed laser with a wavelength of 1064 nm was used as the laser source. The influences of the deposition temperature, laser energy, annealing temperature and focus lens position on the crystallinity of ZnO films were analyzed by X-ray diffraction. The results show that the ZnO thin films obtained at the deposition temperature of 400°C and the laser energy of 250 mJ have the best crystalline quality in our experimental conditions. The ZnO thin films fabricated at substrate temperature 400°C were annealed at the temperatures from 400°C to 800°C in an atmosphere of N₂. The results show that crystalline quality has been improved by annealing, the optimum temperature being 600°C. The position of the focusing lens has a strong influence on pulsed laser deposition of the ZnO thin films and the optimum position is 59.5 cm from the target surface for optics with a focal length of 70 cm.      

Crystal microstructure of annealed nanocrystalline Chromium studied by synchrotron radiation diffraction

The microstructure of electrodeposited nanocrystalline chromium (n-Cr) was studied by using synchrotron radiation (SR) diffraction, SEM, TEM, and EDX techniques. The as-prepared n-Cr samples show the standard bcc crystal structure of Cr with volume-averaged column lengths varying from 25 to 30 nm. The grain growth kinetics and the oxidation kinetics were studied by time resolved SR diffraction measurements with n-Cr samples annealed at 400, 600, and 800 °C. The grain growth process is relatively fast and it occurs within the first 10 min of annealing. The final crystallite size depends only on the annealing temperature and not on the initial grain size or on the oxygen content. The final volume-averaged column lengths observed after 50 min annealing are 40(4), 80(1), and 120(2) nm for temperatures 400, 600, and 800 °C, respectively. It is shown that annealing ex situ of n-Cr at 800 °C both under vacuum and in air gives a grain growth process with the same final crystallite sizes. The formation of the Cr₂O₃ and CrH phases is observed during annealing.     

The effects of post-thermal annealing on the optical parameters of indium-doped ZnO thin films

Indium-doped ZnO thin films are deposited on quartz glass slides by RF magnetron sputtering at ambient temper- ature. The as-deposited films are annealed at different temperatures from 400 C to 800 C in air for 1 h. Transmittance spectra are used to determine the optical parameters and the thicknesses of the films before and after annealing using a nonlinear programming method, and the effects of the annealing temperatures on the optical parameters and the thickness are investigated. The optical band gap is determined from the absorption coefficient. The calculated results show that the film thickness and optical parameters both increase first and then decrease with increasing annealing temperature from 400 C to 800 C. The band gap of the as-deposited ZnO:In thin film is 3.28 eV, and it decreases to 3.17 eV after annealing at 400 C. Then the band gap increases from 3.17 eV to 3.23 eV with increasing annealing temperature from 400 C to 800 C.     

Fabrication and analysis of the structural phase transition of ZrO2 nanoparticles using modified facile sol–gel route

The synthesis of zirconia nanoparticles is achieved through a modified facile sol–gel route. The as-prepared gel is analyzed thermally using TGA and DTA techniques to spot the crystallization process of zirconia nanoparticles. The prepared gel is then annealed at different temperatures and the structure was found to change between tetragonal and monoclinic crystal systems. The first stable tetragonal phase is achieved after annealing for 2?h at 400°C. The annealed powders between 600°C and 800°C demonstrate mixed tetragonal/monoclinic phases. Annealing at 1000°C and higher temperatures up to 1200°C resulted in pure monoclinic phase. Cubic phase was not detected within the annealing temperature range in this study. The elemental analysis of the annealed powder confirmed the formation of zirconia nanoparticles with the chemical formula ZrO₂. The FTIR spectra of the annealed samples introduced a variation in the vibrational bands especially around the phase transition temperature. HR-TEM images reported the formation of nano-zirconia crystals with apparently large particle sizes. The optical energy gap of zirconia nanoparticles is investigated and determined.     

A correlation between structural and optical properties of cobalt oxide nanoparticles for various annealing conditions

Two stable phases of cobalt oxide nanoparticles of controlled sizes have been synthesized using environmentally friendly inorganic precursor. Structural characterization using X-ray diffraction (XRD) shows a single-phase spinal Co₃O₄ structure up to annealing temperature of 800 °C and a mixed phase of Co₃O₄ and CoO particles for T>900 °C. Single-phase CoO nanoparticles are also obtained by annealing the particles at a temperature >900 °C and cooling in inert atmosphere. Average macro- and micro-strain were estimated using XRD data. Macrostrain was found to be the minimum for particles annealed at 600 °C, whereas microstrain was found to decrease with increasing annealing temperature up to 900 °C. A correlation between the density of localized states (DOS) in the band gap and strain is expected because the origin of both strain and DOS are defects and bond length distortions. Sub-gap absorption measurement and model calculations have been used for the determination of DOS. For cobalt oxide nanoparticle samples we find a correlation between estimated strain and density of states in the band gap.     

Annealing induced transformations in structural and optical properties of Ge30Se70−xBix thin films

ABSTRACT

Thin films of Ge₃₀Se_70?xBi_x (x?=?5, 15, 20) were prepared by thermal evaporation method on glass substrates with thickness 800?nm. The films were annealed at 250°C and 320°C for 2?h to study the annealing-induced structural and optical change. The X-ray diffraction characterization revealed the amorphous to crystalline phase transformation with annealing. The indirect optical band gap decreased with annealing which is explained on the basis of phase transformation and density of localized states. The formation of surface dangling bonds around the crystallites during crystallization process reduced the band gap. The Tauc parameter and Urbach energy change show the degree of chemical disorderness in the films. The transmitivity decreased while the absorption coefficient increased with the annealing process. The microstructural study done by Field emission scanning electron microscopy shows the formation of crystallites upon annealing. Atomic force microscopy investigation on these films shows the influence of annealing on surface topography.     

Achieving desired quality of ZnS buffer layer by optimization using air annealing for solar cell applications

The possibility of maximum transmittance at lower thickness of light transmitting ZnS layer and its optimization by air-annealing as an alternative to hazardous and expensive CdS is reported in this communication in order to achieve better buffer layer for solar cells. Thin films of ZnS were deposited using e-beam evaporation on glass and ITO substrates and subjected to air-annealing followed by characterizations for physical properties. XRD patterns revealed amorphous behavior which transformed into cubic (111) plane with change of substrate and annealing whereas surface topography reveals hill and deep valley like structures. Optimal transmittance of maximum 95% in visible region, direct band gap of 3.38 eV and maximum electrical conductivity were observed for 200 °C annealed films. The study refers that films annealed at 200 °C are claimed to be suitable for buffer layer applications.     

Structural and electrochemical studies on thin film LiNi0.8Co0.2O2 by PLD for micro battery

Thin film of LiNi_0.8Co_0.2O₂ (LNCO) has been prepared by Pulsed Laser Deposition (PLD) technique at various post annealing temperatures. XRD results of LNCO thin film deposited on both Pt and Si substrates reveal relatively good crystalline nature at 500 °C which is in good agreement with the electrochemical results. ICP-AES composition analysis indicates 10 to 5% Li loss in the post annealed (400–700 °C) LNCO/Pt thin films; however the as prepared LNCO/Pt films show 17% excess of Li which are comparable with the LNCO target results. SEM analysis indicates phase separation at 600 °C and porous nature at 700–800 °C for LNCO/Pt films. Cyclic voltammetry (CV) scans of LiNi_0.8Co_0.2O₂ film post annealed at 500 °C show a pair of main cathodic and anodic peaks at 3.64 and 3.4 V, respectively with a narrow peak separation reveals good stability upon cycling. Whereas the LNCO films annealed at 600 °C and 700 °C indicate an additional anodic peak at lower potential besides a pair of major peaks which may be due to the phase separated morphology as evidenced from SEM analysis. Based on the structural and electrochemical results, a lithium-ion micro cell has been constructed with LNCO/Li_3.4V_0.6Si_0.4O₄(LVSO)/SnO configuration with the thickness of 1.535 µm and its electrochemical properties have been studied.     

Physical properties of vacuum evaporated CdTe thin films with post-deposition thermal annealing

This paper presents the physical properties of vacuum evaporated CdTe thin films with post-deposition thermal annealing. The thin films of thickness 500 nm were grown on glass and indium tin oxide (ITO) coated glass substrates employing thermal vacuum evaporation technique followed by post-deposition thermal annealing at temperature 450 °C. These films were subjected to the X-ray diffraction (XRD),UV-Vis spectrophotometer, source meter and atomic force microscopy (AFM) for structural, optical, electrical and surface morphological analysis respectively. The X-ray diffraction patterns reveal that the films have zinc-blende structure of single cubic phase with preferred orientation (111) and polycrystalline in nature. The crystallographic and optical parameters are calculated and discussed in brief. The optical band gap is found to be 1.62 eV and 1.52 eV for as-grown and annealed films respectively. The I–V characteristics show that the conductivity is decreased for annealed thin films. The AFM studies reveal that the surface roughness is observed to be increased for thermally annealed films.