Investigation of microwave assisted drying of samples and evaporation of aqueous solutions in trace element analysis

Investigations of microwave assisted drying of sample materials and microwave assisted evaporation of aqueous sample solutions and acidic digestion residues were accomplished by means of special rotors for the microwave digestion system MULTIWAVE. To check the results obtained by microwave assisted drying, the samples were also conventionally dried at 105 degrees C in an oven. The following samples have been dried: 10 g each of meat, fish, apple, cucumber, potato, mustard, yogurt, clay and marl; 1 g each of certified reference material TORT 2 (lobster hepatopancreas), BCR 278 (mussel tissue) and BCR 422 (cod muscle); 500 g garden mould. Microwave assisted drying takes 40 min for organic samples and 30 min for inorganic material. Important is a slow increase of microwave power during the first 20 min. The results agree well with conventional drying at 105 degrees C. Losses of As, Se and Hg have been investigated for 3 CRMs. Only Se shows losses in the range of 20%. Losses of As, Be, Cd, Co, Cr, Cu, Fe, Hg, Li, Mg, Mn, Mo, Ni, Pb, Sb, Se, Sr, Ti, Tl, V and Zn after evaporation of aqueous samples and acidic solutions after wet digestion, respectively, have been investigated. 50 mL aqueous solution was evaporated almost to dryness within 25 min. The recovery of Hg is 40-50%, of Se 90-95% and of the other elements 97-102%. 0.2 g each of TORT 2, BCR 278 and BCR 422 have been digested with 4 mL nitric acid and 1 mL hydrochloric acid by means of the microwave digestion system MULTIWAVE. The digestion residue was evaporated almost to dryness and dissolved again in 10 mL diluted nitric acid. In this case no element losses have been observed. The measured concentration of As, Cd, Cu, Fe, Mn, Hg, Pb, Mo, Ni, Se, Sr, V and Zn agree very well with the certified values. An important prerequisite for good recoveries is not to evaporate the solutions to complete dryness.     

Comparison of sample digestion procedures for the determination of arsenic in certified marine samples using the FI-HG-AAS-technique

 High-pressure digestion and a closed-vessel microwave heated system, both employing a mixture of nitric acid and hydrogen peroxide as digesting agent, were tested for decomposing the certified samples of BCR 278 mussel tissue (Mytilus edulis) and of BCR 422 cod muscle to determine arsenic by use of FI-HG-AAS. While the microwave system is insufficient to mineralize arsenic in marine samples (arsenic recoveries of 13±10% in BCR 278, 2±1% in BCR 422; n=4), high-pressure ashing at 300 °C results in recovery percentages of 56±15% (n=4) in mussel tissue (BCR 278) and of 25±10% (n=4) in cod muscle (BCR 422). A dry ashing procedure is given as a reference digestion, yielding complete recoveries of arsenic for both materials. The nitrite interference arising during measurement can be entirely overcome by using an amino sulfuric acid concentration of about 350 mmol/L in the solutions for measurement. Received: 30 April 1996/Revised: 12 July 1996/Accepted: 16 July 1996     

氢化物发生-双通道原子荧光光谱法同时测定茶叶和木耳中硒及汞量

经洗净烘干并磨碎的试样在硝酸中浸泡过夜后在硝酸-高氯酸中消解,蒸发至冒白烟并继续蒸至近干,加入一定量的盐酸微沸1～2min,使硒(Ⅵ)还原为硒(Ⅳ),溶液用盐酸(5+95)定容至50mL。此溶液由载流盐酸(5+95)溶液送入氢化物发生器,与还原剂10g.L-1 KBH4溶液混合并反应生成硒的氢化物,样品中汞则生成原子态汞蒸气。两者由载气引入原子化器,在选定的仪器工作条件下,测定硒及汞的荧光强度。在实际样品中,硒、汞共存的浓度比未超过10,在同时测定中两者之间互不干扰。按所提出的条件测定,硒、汞的质量浓度在1.0～5.0μg.L-1范围内与相应的荧光强度值之间呈线性关系,方法的检出限(3s/k)依次为0.077,0.009 8μg.L-1。对仪器测定精密度做了试验,测得其相对标准偏差(n=7)依次为1.98%,1.31%。     

Determination of the enantiomeric purity of amphetamine after derivatization with Sanger’s reagent (2,4-dinitrofluorobenzene [DNFB]) by simultaneous dual circular dichroism and ultraviolet spectroscopy

Determination of Se in biological materials was attempted by microwave-induced plasma mass spectrometry (MIP-MS). (1) Serum samples were available after 10 times dilution with 0.5% nitric acid solution containing 0.1% Triton X-100. When oxygen gas was inserted into the plasma gas (nitrogen) in order to improve the combustion, the sensitivity was reduced to 45%. The detection limit of this method was 0.5 ng/mL. (2) Standard reference materials on commercial base were used to evaluate the accuracy of the Se determination by MIP-MS after microwave digestion. In samples like bovine liver and human hair with Se concentrations of more than 0.7 μg/g, the standard curve method after internal standard (IS) correction was acceptable. This procedure was unsuitable for samples with low Se concentrations such as milk powder (certified value of Se 0.11 μg/g), or plant leaf samples. (3) Instead of IS correction, the peak height of the spectrum was used for calculations from the matrix matched calibration curve. The results of all materials were close to the certified values, even at 25 ng/g. The detection limit of the MIP-MS with microwave digestion and IS correction was 0.05 ng/mL in standard solutions. The detection limit of the peak height method was 0.1 ng/mL and was estimated to be < 20 ng/g in plant materials. Received: 25 September 1998 / Revised: 15 February 1999 / Accepted: 18 February 1999     

Simple,fast, and low-contamination microwave-assisted digestion procedures for the determination of chemical elements in biological and environmental matrices by sector field ICP-MS

A simple and convenient method for the digestion of animal tissues, lichens, and plants for 33 metals measured by sector field inductively coupled plasma mass spectrometry (SF-ICP-MS) was described. Microwave-assisted acid digestions were performed at atmospheric pressure by means of a multi-samples rotor designed for processing a large number of samples at once in screw-capped disposable polystyrene liners. The digested samples were filled up to final volume directly in the polystyrene liners ready for elemental quantification. Seven certified reference materials, namely BCR 184 (bovine muscle), BCR 186 (pig kidney), DORM-2 (dogfish muscle), BCR 422 (cod muscle), BCR 62 (olive leaves), BCR 100 (beech leaves), and BCR 482 (lichen) were analysed to verify the accuracy of the method. The linearity range, limit of quantification, precision, and recovery by addition of non-certified elements were also assessed. All elements, with the exception of Hg in BCR 184 and As in BCR 186, were above the quantification limit and blank concentrations, and good agreement existed between found and target values in bovine muscle, pig kidney, and cod muscle. Significant deviations were observed for Al, Co, Cr, Mn, and Ni in dogfish muscle and for Ca, Cr, Fe, and Hg in lichens and plants. The proposed digestion procedure offers a low contamination risk, simplicity, speed, low cost, and applicability in routine analysis, and the SF-ICP-MS method allowed metals from a fraction of ng?g^?1 to hundreds of µg?g^?1 to be quantified in one analytical run.     

Evaluation of microwave-assisted digestion condition for the determination of metals in fish samples by inductively coupled plasma mass spectrometry using experimental designs

This paper describes the development of a compromised single-stage microwave-assisted digestion condition for multi-element determination in fish samples by inductively coupled plasm: mass spectrometry using experimental designs. A Plackett–Burman design was carried out as a multivariate strategy to investigate the main effects of the following parameter on microwave-assisted nitric acid digestion: microwave irradiation time, ramp time, digestion temperature, microwave power limit and the addition of hydrogen peroxide or hydrochloric acid. The most significant microwave setting parameters (radiation time, ramp and temperature) were further evaluated by response surface methodology under Box–Behnken design, while others were kept constant. The influences of different parameters vary according to metal element, thus the working conditions were established as a compromise within optimum region found for each targeted element which ensures quantitative recoveries and time efficiency. The compromised conditions are: ramp to 185°C in 10.5?min then hold for 14.5?min with 1600W (50%) of microwave power, using reagent mixture composed of 2.5?mL nitric acid, 0.5?mL hydrochloric acid and 7.0?mL water. Good agreements were demonstrated between measured and certified values with respect to DORM-3, DOLT-4 and ECM-CE278 and this method was successfully applied for metals determination in tilapia tissues.     

Determination of mercury, selenium, bismuth, arsenic and antimony in human hair by microwave digestion atomic fluorescence spectrometry

A novel method for determination of Hg, Se, Bi, As and Sb based on microwave digestion followed by continuous flow vapour generation atomic fluorescence spectrometry was developed. The digestion for Hg was based on a two stage digestion involving HNO(3) and H(2)O(2), whilst for the hydride forming elements a common digestion using HCl and H(2)O(2) was found to be the most effective. The instrumentation and chemistry were optimised in order to provide the best accuracy and precision. The method detection limit for hair samples was found to be 0.2 ng g(-1) for Hg and between 2 and 10 ng g(-1) for the hydride forming elements. The atomic fluorescence detector showed excellent linearity over the concentration ranges studied with linear correlation co-efficients between 0.99984 and 0.99997. To validate the accuracy of the method a human hair certified reference material (GBW 0706) was analysed and excellent agreement with the certified value was obtained for all elements.     

微波消解样品-电感耦合等离子体原子发射光谱法测定铅精矿中铅、砷、镉、汞

采用微波消解样品-电感耦合等离子体原子发射光谱法同时测定铅精矿中主体元素铅及有毒有害元素砷、镉、汞的含量。0.20g试样置于消解罐中,先后加入硝酸9mL、盐酸3mL、氟硼酸2mL及过氧化氢2.5mL,密闭罐盖按设定的微波消解程序进行消解。试验选择铅、砷、镉和汞的分析线分别为220.351,189.042,228.802,184.950nm以消除基体干扰。铅、砷、镉、汞的检出限分别为16.0,2.2,0.4,0.8μg.g-1。方法用于铅精矿标准样品(GBW 07617)和铅精矿实际样品分析,此方法的测定值与认定值及原子吸收光谱法或原子荧光光谱法的测定值相一致。方法的相对标准偏差(n=10)在0.15%～3.9%之间。     

Determination of selenium in marine biological tissues by transverse heated electrothermal atomic absorption spectrometry with longitudinal Zeeman background correction and automated ultrasonic slurry sampling.

A fast, sensitive, and reliable method for determination of selenium in marine biological tissues by electrothermal atomic absorption spectrometry with slurry sampling was developed. Slurries were prepared from fresh and frozen seafood samples that were previously homogenized, dried, and ground; particle sizes <100 microm were taken for analysis. A 3% (v/v) HNO3 solution containing 0.01% (v/v) Triton X-100 was used as slurry diluent. Slurries were mixed on an automated ultrasonic slurry sampler at 20% amplitude for 30 s just before an aliquot was injected into the furnace. The method was successfully validated against the following certified reference materials: NRCC CRM DORM-2 (Dogfish muscle); NRCC CRM TORT-2 (Lobster hepatopancreas); NRCC CRM DOLT-2 (Dogfish liver); and BCR CRM 278 (Mussel tissue), and was subsequently applied to determination of Se in 10 marine biological samples. The influences of the drying procedure (oven-, microwave-, and freeze-drying), matrix modifier amount, mass of solid material in cup, and pipetting sequence are discussed. The limit of determination of Se was 0.16 microg/g and the repeatability, estimated as between-batch precision, was in the range of 4-8%. Se contents in the samples ranged from 0.6 to 2.8 microg/g. The proposed method should be useful for fast assessment of the daily dietary intake of Se.     

Graphite furnace analysis—getting easier and achieving more?

The impact of microwave digestion, hot injection of solutions and chemical modification on the analysis of biological samples by electrothermal atomic absorption spectrometry (AAS) has been assessed. The stabilizing effects of palladium and ruthenium modifiers were compared. Although ruthenium has a higher atom appearance temperature, palladium was the more useful modifier when samples other than water were analysed. When 2 μg of palladium (as PdCl₂) was preconditioned in hydrogen at 500°C, volatile elements were retained at char temperatures up to 1000–1100°C. This allowed similar atomizer programmes to be used for Cd, Cu, Fe, Mn and Pb and accurate determination of these analytes in solutions of reference materials was achieved aqueous standards. Rapid drying of the solutions by hot injection at 120°C reduced the programme time to just over 1 min. A combination of microwave digestion, hot injection of 40% (w/v) HNO₃ solutions and Pd modification produced a rapid and sensitive method for determination of Cd and Pb at sub-μg g^?1 levels in vegetable and protein foodstuffs. Palladium modification also proved useful in simultaneous multi-element determination by continuum source AAS. The picogram detection limits obtained for Cr, Mn and Pb were similar to line source AAS values recorded with the same compromise programme. Accurate determination of Cd, Cr, Cu, Mn, Mo and Pb in NIST SRM 1566 Oyster Tissue indicated the potential of continuum source AAS for multi-element determinations. The advantages of palladium modifications were also illustrated for furnace atomic non-thermal excitation spectrometry (FANES) with a hollow-cathode discharge. The maximum char temperatures of Ag, Ga, Hg, Pb, Sb and Se were increased by 300–600°C in the presence of 1 μg of Pd, although the detection limits were a factor of two poorer.     

Fractionation of heavy metals in sediment by using microwave assisted sequential extraction procedure and determination by inductively coupled plasma mass spectrometry

In this work, a fast microwave assisted extraction procedure was developed and optimized for the heavy metals (Cu, Ni, Cr, Pb and Cd) partitioning in the three-stage sequential extraction procedure proposed by the European Standards, Measurements and Testing (SM&;T) Program, formerly the Community Bureau of Reference (BCR). The microwave oven procedure was optimized to obtain extraction efficiencies similar to the conventional BCR procedure, in less time, while using smaller volumes of reagents. In the optimization process, three variables (extraction time, ramping time and microwave power) were considered as factors and as a response the concentration of different metal ions in each individual BCR fraction. Interactions between analytical factors and their optimized levels were investigated using a central composite design. Extractable metals obtained by both comparable methodologies were measured by inductively coupled plasma mass spectrometry. With the use of optimal microwave conditions, steps 1–3 of the sequential extraction (including the hydrogen peroxide digestion in step 3) could be completed between 21 and 22 min. Detection limits were between 1 and 18 ng l^{− 1}. The accuracy of the proposed method was checked with a certified reference material (CRM) of Lake Sediment BCR 701. Values obtained were in accordance with those reported for the certified material with only a few exceptions. Different origin sediments (river and marine) were analyzed by both BCR and MW procedures, and the results obtained were comparable according to the t-paired-test for a 95% confidence level.     

Use of microwave digestion and atomic absorption spectrophotometry to determine chromic oxide as a digestibility marker in feed, feces, and ileal content.

Most conventional digestion procedures, such as dry ashing and wet ashing, are tedious and labor intensive. Microwave digestion is a good alternative, because microwave dissolution is faster, safer, and simpler, and provides more controlled reproducible conditions than conventional methods. The purpose of this study was to develop a microwave digestion method for mineralizing meat and bone meal diets, feces, and ileal contents. Each sample was heated on a hot plate for 10 min, dry ashed at 65 degrees C for 4 h, and transferred into microwave vessels. Then, 10 mL 70% HNO3 was added. Samples were digested for 7, 10, and 20 min at 95, 90, and 85% power, respectively. After the heating cycle, 6 mL 30% H2O2 was added, and samples were returned to the microwave for a second heating cycle of 1 and 7 min at 95% and 90% power, respectively. Finally, chromium concentration was determined by flame atomic absorption spectrophotometry. The digestion method was validated by using a standard reference material, SRM domestic sludge 2781, with a certified chromium value of 195 +/- 9 micrograms/g. The value obtained in this study was 178 +/- 11 micrograms/g, for a difference of 17 micrograms/g. Spike recovery experiments resulted in 103.16 and 100.35% recoveries of chromium from diet and feces samples, respectively. Coefficients of variation were 10.8 and 7.8%, respectively.     

Element fingerprinting of marine organisms by dynamic reaction cell inductively coupled plasma mass spectrometry

A method for the determination of sixteen elements (Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Se, Sn, V, Zn) in seafood by dynamic reaction cell inductively coupled plasma mass spectrometry (ICP–DRC–MS) is presented. A preliminary study of polyatomic interferences was carried out in relation to the chemical composition of marine organisms belonging to different taxa. Acid effects and other matrix effects in marine organisms submitted to closed-vessel microwave digestion were investigated as well. Ammonia was the reactive gas used in the DRC to remove polyatomic ions interfering with ²⁷Al, ⁵²Cr, ⁵⁶Fe and ⁵¹V. Optimal conditions for the simultaneous determination of analytes were identified in order to develop a fast multielement method. A suite of real samples (mussels and various fish species) were used during method development along with three certified reference materials: BCR CRM 278R (mussel tissue), BCR CRM 422 (cod muscle) and DORM-2 (dogfish muscle). The proposed analytical approach can be used in conjunction with suitable chemometric procedures to address quality and safety issues in aquaculture and fisheries. As an example, a case study is described in which mussels from three farming sites in the Venice Lagoon were distinguished by multivariate analysis of element fingerprints.      

Cadmium analysis in soil by microwave acid digestion and graphite furnace atomic absorption spectrometry

The need to determine micronutrients and toxic elements in soils has grown in recent years and cadmium is of special interest. A method has been developed for the determination of cadmium in soils based on a prior acid digestion of the samples with nitric acid in closed Teflon vessels, into a microwave over. The cadmium determination was carried out by graphite furnace atomic absorption spectrometry (GFAAS) with L'vov platform. Optimum operating conditions, analyte modifiers and matrix interferences have been investigated. The best matrix modifier was found to be ammonium dihydrogen phosphate. The interferences are greatly reduced under these operating conditions and calibration can be performed with simple aqueous solutions of the metal standard. The method is rapid and provides accurate and precise results that agree with certified values for two reference materials: BCR 141 (calcareous loam soil) and BCR 277 (estuarine sediment).     

Determination of the enantiomeric purity of amphetamine after derivatization with Sanger’s reagent (2,4-dinitrofluorobenzene [DNFB]) by simultaneous dual circular dichroism and ultraviolet spectroscopy

Determination of Se in biological materials was attempted by microwave-induced plasma mass spectrometry (MIP-MS). (1) Serum samples were available after 10 times dilution with 0.5% nitric acid solution containing 0.1% Triton X-100. When oxygen gas was inserted into the plasma gas (nitrogen) in order to improve the combustion, the sensitivity was reduced to 45%. The detection limit of this method was 0.5 ng/mL. (2) Standard reference materials on commercial base were used to evaluate the accuracy of the Se determination by MIP-MS after microwave digestion. In samples like bovine liver and human hair with Se concentrations of more than 0.7 μg/g, the standard curve method after internal standard (IS) correction was acceptable. This procedure was unsuitable for samples with low Se concentrations such as milk powder (certified value of Se 0.11 μg/g), or plant leaf samples. (3) Instead of IS correction, the peak height of the spectrum was used for calculations from the matrix matched calibration curve. The results of all materials were close to the certified values, even at 25 ng/g. The detection limit of the MIP-MS with microwave digestion and IS correction was 0.05 ng/mL in standard solutions. The detection limit of the peak height method was 0.1 ng/mL and was estimated to be < 20 ng/g in plant materials.     

Determination of metals in marine species by microwave digestion and inductively coupled plasma mass spectrometry analysis

A microwave digestion method suitable for determination of multiple elements in marine species was developed, with the use of cold vapor atomic spectrometry for the detection of Hg, and inductively coupled plasma mass spectrometry for all of the other elements. An optimized reagent mixture composed of 2 ml of HNO₃, 2 ml of H₂O₂ and 0.3 ml of HF used in microwave digestion of about 0.15 g (dry weight) of sample was found to give the best overall recoveries of metals in two standard reference materials. In the oyster tissue standard reference material (SRM 1566b), recoveries of Na, Al, K, V, Co, Zn, Se, Sr, Ag, Cd, Ni, and Pb were between 90% and 110%; Mg, Mn, Fe, Cu, As, and Ba recoveries were between 85% and 90%; Hg recovery was 81%; and Ca recovery was 64%. In a dogfish certified reference material (DORM-2), the recoveries of Al, Cr, Mn, Se, and Hg were between 90% and 110%; Ni, Cu, Zn, and As recoveries were about 85%; and Fe recovery was 112%. Method detection limits of the elements were established. Metal concentrations in flounder, scup, and blue crab samples collected from coastal locations around Long Island and in the Hudson River estuary were determined.     

Development of a wide bore flow through microwave digestion device for the determination of trace metals in soil

A flow through microwave digestion device has been developed for the determination of Cd, Cr, Mn, Ni and Pb in soil by aqua regia extraction. This device differs from existing commercially available devices as it uses a double pumping action to replace the back pressure regulator traditionally used to achieve internal pressurisation. An acid front has also been included to overcome problems associated with the dilution of acid in samples due to dispersion. Recoveries between 95 and 105% of certified values were achieved with standard deviations of less than 4% for certified reference soil (BCR 143R). A sample throughput of 6 samples per hour was achieved in the optimised system. The performance of the device was tested by digesting real soil samples ground through a 250 microns sieve and slurried without the use of surfactants. A comparison of analytical performance for analysing real samples was made between the microwave flow method and a thermal method.     

Determination of twenty-five elements in lichens by sector field inductively coupled plasma mass spectrometry and microwave-assisted acid digestion

A simple and efficient digestion method for rapid sample preparation and quantification of 25 chemical elements in lichens by sector field inductively coupled plasma mass spectrometry is described. A microwave (MW)-assisted acid digestion was carried out at atmospheric pressure simultaneously handling up to 80 samples in screw-capped disposable polystyrene tubes. This digestion procedure was compared with the established MW digestion in closed vessels in order to examine its potential applicability in routine analysis for environmental monitoring. Three certified reference materials, i.e. BCR 482 (lichens), BCR 62 (olive leaves) and BCR 100 (beech leaves), as well as a small set of real samples were analyzed. Limits of quantification, accuracy and precision of the method were assessed. The majority of the elements were totally recovered from the lichens and from the other vegetable matrices. Low contamination risk, simplicity, time-saving, and applicability in routine analyses make this method very suitable for use in extensive screening campaigns.     

Determination of silicon in biological samples by ICP-OES after non-oxidative decomposition under alkaline conditions.

A non-oxidative alkaline sample digestion procedure using tetramethylammonium hydroxide and a high pressure, microwave assisted autoclave digestion system was developed. The silicon concentrations of the digested samples were measured by inductively coupled axial plasma optical emission spectrometry (ICP-OES). Details of the digestion conditions as well as the optimised instrumental parameters for ICP-OES are described. The method was developed and tested using silicon-spiked ascorbic acid and applied to samples of animal tissue and organs. The total silicon content of two different reference materials, NIST 1577b Bovine liver and BCR 184 Bovine Muscle having neither certified nor informational values for Si was determined. The results obtained are compared with the results of independent methods such as wavelength dispersive x-ray fluorescence spectrometry (WDXRF) and solid sampling electrothermal atomic absorption spectrometry (ETAAS). The method described achieves a limit of detection of 2 mg kg(-1) using 100 mg of solid biological or organic material and covers a concentration range of up to 500 mg kg(-1).