Ultrasonic effects on electroorganic processes. Part 14. Indirect electroreduction of benzyl chlorides with anthracene redox-mediatory system

Ultrasonic effects were observed in the indirect electroreduction of benzyl chlorides with a radical anion mediator electrogenerated from anthracene. Both the current efficiency for the toluenes formed and the current density (reaction rate) at a working electrode were significantly increased in potential-controlled electrolysis under ultrasonic irradiation (20 kHz). These effects are important from a practical aspect and are rationalized as being due to mass transport promotion caused by ultrasonic cavitation. Although the efficiency could be also increased in the direct electroreduction in the absence of the mediator under irradiation, the current density was only slightly increased.     

超声场对钛基PbO2电极电化学氧化Cr3+过程电流效率的影响

本文研究了超声场对Ti／SnO2 Sb2O3／PbO2电极电化学氧化Cr3 过程的影响,探讨了在不同的操作电流密度、反应温度、硫酸浓度及Cr3 浓度下,超声场对硫酸介质中Cr3 电化学氧化生成Cr2O72-过程中的电流效率的影响,并用扫描电镜对有无超声场时不同反应时间下的电极形貌进行了分析。实验结果表明:在相同的反应条件下,有超声场作用时Cr3 电化学氧化过程的电流效率明显高于无超声场时的电流效率。扫描电镜测定发现,有超声场作用时不同反应时间下电极的形貌有明显的变化。     

Ultrasonic waste-water treatment: incidence of ultrasonic frequency on the rate of phenol and carbon tetrachloride degradation

Organic compounds in aqueous solution submitted to an ultrasonic irradiation behave differently according to their physical and chemical properties. In this work, hydrogen peroxide formation and the degradation rate of phenol and carbon tetrachloride have been studied at different frequencies: 20, 200, 500 and 800 kHz. Whatever the frequency, it is easier to decompose CCl₄ than phenol by means of ultrasonic wave. It is shown that the rates of reactions involving hydroxyl radicals (hydrogen peroxide formation and phenol degradation) have a maximum value at 200 kHz. The best yield observed at 200 kHz for the phenol degradation may be the result of better HO radicals availability outside of the bubble of cavitation. The degradation rate for carbon tetrachloride which decomposes into the bubble of cavitation increases with frequency. Calculating the reaction rate for one ultrasonic period shows that the efficiency of one ultrasonic cycle decreases as frequency increases.     

Electron-irradiated n+-Si as hole injection tunable anode of organic light-emitting diode

Traditionally, n-type silicon is not regarded as a good anode of organic light emitting diode (OLED) due to the extremely low hole concentration in it; however, when doped with Au element which acts as carrier generation centers, it can be, as shown in our previous work. In this study, we demonstrate a new kind of carrier generation centers in n⁺-type silicon, which are the defects produced by 5 MeV electron irradiation. The density of carrier generation centers in the irradiated n⁺-Si anode can be controlled by tuning the electron irradiation time, and thus hole injection current in the OLEDs with the irradiated n⁺-Si anode can be optimized, leading to their much higher maximum efficiencies than those of the OLEDs with non-irradiated n⁺-Si anode. For a green phosphorescent OLED with the irradiated n⁺-Si anode, the current efficiency and power efficiency reach up to 12.1 cd/A and 4.2 lm/W, respectively.     

A standard method to calibrate sonochemical efficiency of an individual reaction system

Fricke reaction, KI oxidation and decomposition of porphyrin derivatives by use of seven types of sonochemical apparatus in four different laboratories were examined in the range of frequency of 19.5 kHz to 1.2 MHz. The ultrasonic energy dissipated into an apparatus was determined also by calorimetry. Sonochemical efficiency of Fricke reaction and KI oxidation was defined as the number of reacted molecule per unit ultrasonic energy. The sonochemical efficiency is independent of experimental conditions such as the shape of sample cell and irradiation instruments, but depends on the ultrasonic frequency. We propose the KI oxidation dosimetry using 0.1 moldm(-3) KI solution as a standard method to calibrate the sonochemical efficiency of an individual reaction system.     

Sonochemical effect and pore structure tuning of silica xerogel by ultrasonic irradiation of semi-solid hydrogel

Silica xerogels were prepared by the sol-gel method under ultrasonic irradiation, using tetraethylorthosilicate (TEOS) as the starting material. Hexamethyldisiloxane (HMDSO) was used as the hydrophobizing agent. When preparing silica xerogel, it is necessary to perform aging and hydrophobization to suppress shrinkage during ambient pressure drying, however, such treatments are time-consuming. In this study, the semi-solid hydrogel was irradiated with ultrasonic for the first time in order to accelerate aging and hydrophobic treatment, and the effect of ultrasonic frequency on structure was investigated. Firstly, ultrasonic irradiation was performed at frequencies of 100 kHz and 500 kHz, followed by hydrophobic treatment at a frequency of 500 kHz, in order to promote aging. The results identify optimum conditions for ultrasonic irradiation to promote aging and hydrophobization reactions, and it was found to be possible to prepare silica xerogels in less than 1/5 of the conventional time. The silica xerogels had a low density and the shrinkage was suppressed. In this study, it was found that ultrasonic irradiation of semi-solid hydrogel was very effective for promoting the reaction.     

Evaluation of ammonia–nitrogen removal efficiency from aqueous solutions by ultrasonic irradiation in short sonication periods

In this study, mechanisms and efficiency of ammonia–nitrogen removal from aqueous solutions by ultrasonic irradiation were investigated. Depending on the factors affecting the sonication (initial concentration, initial pH, ultrasonic power density and sonication period), sonication tests were carried out and ammonium–nitrogen removal efficiency by ultrasonic irradiation was determined. In these experiments, ammonia–nitrogen removal efficiency was achieved in the range of 8–64%. In short sonication periods, the best ammonia–nitrogen removal efficiency was achieved at pH 8.2–11. Lower ammonia–nitrogen removal efficiency was observed in high initial ammonia–nitrogen concentration of solutions. It was observed that high initial ammonia–nitrogen concentrations may led to decreased ammonia–nitrogen removal efficiency however quantity of ammonia–nitrogen removal was higher. Because high initial concentration had a negative impact on the sonochemical reactions the heat of cavitation bubbles was reduced. Ammonia–nitrogen removal efficiency was increased with ultrasonic density and sonication period. This study showed that effective ammonia–nitrogen removal could be achieved by the ultrasonic irradiation in short sonication periods (as 60–600 s). Specific cost of ammonia–nitrogen removal by the ultrasonic irradiation from simulated ground water, surface water, wastewater and landfill leachate was also calculated. The specific removal cost was varied between 0.01 and 0.25 $/g ammonia–nitrogen.     

Influence of ultrasonic waves in the reduction of nitrate to nitrite by hydrazine-Cu(II)

Colorimetric methods are still important for determining nitrate and nitrite. A critical step in the use of these methods to determine nitrate in low concentrations is the reaction time required to totally reduce nitrate to nitrite, i.e., 24h in the dark. This work involved a study of the influence of ultrasonic irradiation on the nitrate reduction reaction by hydrazine. Our findings indicated that ultrasonic irradiation, associated with copper(II) ion as a catalyst, increased the redox reaction rate, decreasing the reaction time to about 10min when the power of the ultrasonic irradiation was set in 14.0357W. The strong influence of the ultrasonic irradiation in the reduction reaction rates can be sustained by an excellent linear correlation (R(2)=0.9993) between the kinetic constants and ultrasonic powers. Nitrate conversion also increased from 68% to 98% at the latter conditions. It thus become clear that high intensity ultrasound is very beneficial for this reduction reaction to proceed in good yield and in short reaction time in comparison to its silent reaction.     

Ultrasound-assisted dextranase entrapment onto Ca-alginate gel beads

In this research work, dextranase has immobilized onto calcium alginate beads using a novel ultrasound method. The process of immobilization of the enzyme was carried out in a one-step ultrasound process. Effects of ultrasound conditions on loading efficiency and immobilization yield of the enzyme onto calcium alginate beads were investigated. Furthermore, the activity of the free and immobilized enzymes prepared with and without ultrasound treatment, as a function of pH, temperature, recyclability and enzyme kinetic parameters, was compared. The maximum loading efficiency and the immobilization yield were observed when the immobilized dextranase was prepared with an ultrasonic irradiation at 25 kHz, 40 W for 15 min, under which the loading efficiency and the immobilization yield increased by 27.21% and 18.77%, respectively, compared with the immobilized enzymes prepared without ultrasonic irradiation. On the other hand, immobilized enzyme prepared with ultrasonic irradiation showed V_max and K_M value higher than that for the immobilized enzyme prepared without ultrasonic irradiation, likewise, both the catalytic and specificity constants of immobilized enzyme prepared with ultrasonic irradiation were higher than that for immobilized enzyme prepared without ultrasound, indicating that, this new ultrasonic method improved the catalytic kinetics activity of immobilized dextranase at all the reaction conditions studied. Compared with immobilized enzyme prepared without ultrasound treatment, the immobilized enzymes prepared with ultrasound irradiation exhibited: a higher pH optimum, optimal reaction temperature, activation energy, and thermal stability, as well as, a higher recyclability, which, illustrating the effectiveness of the sonochemical method. To the best of our knowledge, this is the first report on the effect of ultrasound treatments on the immobilization of dextranase.     

Sonochemical and photosonochemical degradation of 4-chlorophenol in aqueous media

The degradation of 4-chlorophenol (4-CP) in aqueous media by 516 kHz ultrasonic irradiation was investigated in order to clarify the degradation mechanism. The degradation of concentrated 4-CP solution by means of ultrasound, UV irradiation and their combined application was also studied. The obtained results indicate that *OH radical are the primary reactive species responsible for 4-CP ultrasonic degradation. Very little 4-CP degradation occurs if the sonolysis is carried out in the presence of the *OH radical scavenger tert-butyl alcohol, also indicating that little or no pyrolysis of the compound occurs. The dominant degradation mechanism is the reaction of substrate with *OH radicals at the gas bubble-liquid interface rather than high temperature direct pyrolysis in ultrasonic cavities. This mechanism can explain the lower degradation rate of the ionic form of 4-CP that is partly due to the rapid dissociation of *OH radicals in alkaline solutions. The sonochemical destruction of concentrated 4-CP aqueous solution is obtained with low rate. Coupling photolysis with ultrasound irradiation results in increased efficiency compared to the individual processes operating at common conditions. Interestingly, the photosonochemical decomposition rate constant is greater than the additive rate constants of the two processes. This may be the result of three different oxidative processes direct photochemical action, high frequency sonochemistry and reaction with ozone produced by UV irradiation of air, dissolved in liquid phase because of the geyser effect of ultrasound streaming. Additionally, the photodecomposition, at 254 nm, of hydrogen peroxide produced by ultrasound generating *OH radical can partly explain the destruction enhancement.     

注入和输运对单层有机发光器件复合发光的影响

通过分析聚合物电致发光器件中载流子注入、输运、激子的解离与复合过程,提出了激子解离与复合的理论模型. 基于电流连续性方程和Poisson方程,给出了激子复合密度、电流密度及复合效率表达式.研究两电极与有机层之间在Ohmic和Fowler-Nordheim接触条件下载流子迁移率对器件中激子的复合密度及外加电压和注入势垒对器件电流和复合效率的影响.结果表明:1)在一个较宽的注入势垒和迁移率范围内,复合密度不是由两个注入电极的相对注入比决定而是由有机层电子和空穴迁移率之比所支配;2)固定阴极势垒,而阳极势垒由小变大时,器件电流由接触限制向空间电荷限制转变;3)复合效率随外电压升高先增加,当电压达一临界值时而陡降,存在一个最佳的注入势垒值.结果说明:电极与有机层的能带匹配及有机层间的迁移率匹配对器件复合发光有着极其重要的影响.其计算值与所报道的理论结果相符.     

Ultrasound-assisted oxidative process for sulfur removal from petroleum product feedstock

A procedure using ultrasonic irradiation is proposed for sulfur removal of a petroleum product feedstock. The procedure involves the combination of a peroxyacid and ultrasound-assisted treatment in order to comply with the required sulfur content recommended by the current regulations for fuels. The ultrasound-assisted oxidative desulfurization (UAOD) process was applied to a petroleum product feedstock using dibenzothiophene as a model sulfur compound. The influence of ultrasonic irradiation time, oxidizing reagents amount, kind of solvent for the extraction step and kind of organic acid were investigated. The use of ultrasonic irradiation allowed higher efficiency for sulfur removal in comparison to experiments performed without its application, under the same reactional conditions. Using the optimized conditions for UAOD, the sulfur removal was about 95% after 9 min of ultrasonic irradiation (20 kHz, 750 W, run at 40%), using hydrogen peroxide and acetic acid, followed by extraction with methanol.     

ZnO:Zn低能电子发光的亮度饱和

本文讨论了ZnO:Zn低能电子发光亮度饱和的物理原因。指出,在Vg=Va(通常数字显示的情况)的条件下,亮度饱和的主要原因是ZnO:Zn次级电子发射和阴极发射疲劳;若取Vg=Va,则饱和亮度成倍提高,这时热猝灭将是亮度饱和的主要因素。同时指出,对于一定的输入功率,存在着一个与最佳效率相对应的最佳阳极电流密度;低阳极电流密度,高阳极电压往往是低效率的。作者根据本文的研究结果,制成了饱和亮度高达37,000cd/m2的发光管和饱和亮度为22,000cd/m2、能在5,000至10,000cd/m2稳定工作的高亮度数字显示管。后者配上适当的滤光片、在阳光直接照射或照度高达100,000lux的条件下仍能清晰地阅读。     

Measurements of coating density using ultrasonic reflection coefficient phase spectrum

A nondestructive method to determine the density of coating has been proposed in this paper based on the ultrasonic reflection coefficient phase spectrum (URCPS). A model was set up first to represent the ultrasonic waves reflected from a coating system at normal incident, and the relation between the extremum of URCPS and the coating density was established to provide the principle of determining the density. The ultrasonic method was validated on a series of ZrO2-7 wt.%Y2O3 (YSZ) coatings with various density. The specimens were prepared by electric beam physical vapor deposit (EB-PVD). After deposition, the specimens were irradiated using high-intensity pulsed ion beam (HIPIB) at different ion current density of 100 and 200 A/cm2 to change coating density. The coating densities of as-deposited and post irradiation by HIPIB were derived to be 4940-5030, 5200-5320 and 5390-5470 kg/m3, respectively. The relative error between the coating density measured by the ultrasonic method and Archimedean principle ranging from 2.53% to 6.11%, indicates that the proposed ultrasonic quantification method provides a reliable nondestructive way to determine coating density.     

MoO3为缓冲层的高效非掺杂蓝色有机发光二极管

以典型蓝色发光材料-联苯乙烯衍生物(4,4’-bis(2,2’-diphenylvinyl) -1,1’-biphenyl,DPVBi)为发光层,采用MoO3为阳极缓冲层制备了结构简单的非掺杂型蓝色有机电致发光器件.在电流密度为20 mA/cm2、MoO3缓冲层厚度为0.5 nm对器件效率约为无缓冲层器件效率的18倍,...     

Ultrasonic effects on electroorganic processes--Part 20. Photocatalytic oxidation of aliphatic alcohols in aqueous suspension of TiO2 powder

Ultrasonic effects in a suspension system were examined using the photocatalytic oxidation of 2-propanol to acetone and of ethanol to acetaldehyde in the aqueous suspension of TiO2 powder as a model reaction. The formation rate of acetone was significantly increased under ultrasonic irradiation. The oxidation reaction under ultrasonic irradiation was affected in a different manner from that in silence by reaction conditions such as ultrasonic power, stirring speed, amount of TiO2, concentration of 2-propanol, and pretreatment of the TiO2 powder. Furthermore, it was also observed that the particle size of the TiO2 photocatalyst powder was increased due to the particle agglomeration by ultrasonic irradiation, and consequently it was suggested that ultrasound activates the surface of the catalyst. These results are discussed on the basis of not only the activation of the photocatalyst but also ultrasonic enhancement of mass transport of 2-propanol molecules.     

Inactivation of Saccharomyces cerevisiae by ultrasonic irradiation

We have investigated the inactivation of Saccharomyces cerevisiae (yeast cells) by ultrasonic irradiation. The amplitude on the vibration face contacting the sample solution was used as an indication of the ultrasonic power intensity. The effects of the amplitude on the vibration face and the initial cell numbers on the sonolytic inactivation of yeast cells have been investigated using a horn-type sonicator (27.5 kHz). The inactivation of the yeast cells by ultrasonic irradiation shows pseudo first-order behavior. The inactivation rate constant varied from 0.0007 to 0.145 s(-1) when the amplitude on the vibration face was in the range of 1-7 microm(p-p). The change in the inactivation rate constant as a function of the amplitude on the vibration face was similar to that of the OH radical formation rate under the same conditions. The threshold of this sonicator was 3 microm(p-p) with the amplitude on the vibration face. The initial cell numbers (from 10(2) to 10(5) mL(-1)) had an influence on the inactivation of the yeast cells by ultrasonic irradiation. The inactivation rate constants varied from 0.023 to 6.4 x 10(-3) s(-1), and the inactivation by ultrasonic irradiation was fastest at the lowest initial cell numbers. In a squeeze-film-type sonicator (26.6 kHz), 90% inactivation of the yeast cells was achieved by ultrasonic irradiation for 60 min.     

Drastic acceleration of fibrillation of insulin by transient cavitation bubble

Amyloid-fibril formation of proteins can be accelerated by ultrasonic irradiation to the peptide solutions. Although this phenomenon contributes to understanding pathogenic behavior of amyloidosis, its physical mechanism has not been clarified, because several factors (cavitation, temperature increase, stirring effect, and so on) related to ultrasonic irradiation can participate in the fibrillation reaction. Here, we independently study contributions of the possible factors, using insulin, which is extremely stable and then suitable for the mechanism clarification. We find that the optimized ultrasonic irradiation can drastically accelerate the fibrillation reaction; the time for completing the reaction is shortened compared with the high-speed (1200 rpm) stirring agitation by a factor of 430. The fibrillation reaction proceeds only when the subharmonic-mode intensity exceeds a threshold, indicating generation of the transient cavitation bubbles. Our results reveal that not the temperature increase but the transient cavitation bubbles work as the dominant accelerator of the fibrillation reaction.     

Control of the temperature responsiveness of poly(N-isopropylacrylamide-co-2-hydroxyethyl methacrylate) copolymer using ultrasonic irradiation

Poly(N-isopropylacrylamide-co-2-hydroxyethyl methacrylate) (poly(NIPAM-co-HEMA)) is a temperature-responsive copolymer that is expected to be applicable as an advanced functional polymeric material in various fields. In this study, a novel method was developed to control the responsive temperature of poly(NIPAM-co-HEMA) using an ultrasonic polymerization technique. Initially, the behavior of the reaction was investigated using NIPAM and HEMA monomers under ultrasonic irradiation. A high ultrasonic power was found to produce a high reaction rate and low number average molecular weight of the copolymer. The polydispersity of the synthesized copolymer was approximately 1.5 for all ultrasonic powers examined. In the early stage of the reaction, the molar fraction of NIPAM in the copolymer was lower than the initial molar fraction of the monomers. It was concluded that ultrasonic irradiation affected the initiation reaction and polymer degradation, but did not affect the propagation reaction. Furthermore, the effect of the ultrasonic irradiation conditions on the temperature responsiveness of the copolymer was investigated. The lower critical solution temperature (LCST) of the copolymer was found to increase with increasing ultrasonic irradiation time. In addition, in the early stages of the reaction, the measured values of the LCST were higher than the estimated values using copolymer composition. This can be attributed to some parts of the copolymer chain possessing a higher NIPAM fraction than the overall fraction due to different reactivities of the monomers and terminated radicals. This hypothesis was indirectly verified by the synthesis of a block copolymer from the PNIPAM homopolymer and HEMA monomer.     

Reactive dye degradation by combined Fe(III)/TiO2 catalyst and ultrasonic irradiation: Effect of Fe(III) loading and calcination temperature

The development of Fe(III)/TiO(2) catalysts for sonocatalytic degradation of Reactive Blue 4 (RB4) dye in water was carried out using sol-gel method. Their surface morphology, phase transformation and surface characteristics were studied using SEM, XRD and surface analyzer, respectively. Phase transformation from amorphous to anatase occurred at 500°C and transformation of anatase to rutile phase occurred at 700°C. Complete rutile phase was formed at 900°C with corresponding increase in the particle size. Increasing in Fe(III) loading led to a reduction in the anatase phase and with the formation of weaker and broader of diffraction peaks. Surface morphology of the prepared catalyst was clearly observed with increasing calcination temperature. Surface area of the prepared catalyst decreased with increasing calcination temperature or increasing Fe(III) loading. The combination of 0.4 mol% of Fe(III)/TiO(2) with ultrasonic irradiation gave the highest sonocatalytic activity in the removal of RB4 from the aqueous solution. On the other hand, the presence of even small amount of rutile inhibited the catalytic activity of catalyst. 1.5 g/L was the optimum amount of catalyst that led to the highest sonocatalytic degradation of RB4 with an efficiency of 90%. Aeration significantly accelerated the reaction rate. Higher removal at 96% could be achieved with the combination of 0.4Fe(III)/TiO(2) and aeration under ultrasonic irradiation.