Determination of limiting current density for different electrodialysis modules

Limiting current density of ammonium nitrate solution in laboratory-, pilot-, and industrial-scale electrodialysis modules were determined to provide a method for the prediction of the limiting current density of ammonium nitrate solutions at any conditions. The current-voltage curve was measured in each case and the limiting current density was evaluated using the dependence of the derivative, dI/dU, on the electric current, I. The limiting current was determined as a current at which the derivative dI/dU equals zero. The developed method enables not only the prediction of the limiting current density but the limiting cut and limiting flux can be determined concurrently at any linear flow velocity of the diluate and inlet ammonium nitrate concentration. It could help to prevent working in the overlimiting region and to avoid undesirable decrease of current efficiency and pH changes. The limiting cut is the maximal cut that can be obtained at certain linear flow velocity and module geometry irrespective of the inlet ammonium nitrate concentration and it is very useful information when designing a new electrodialysis unit for specific application.     

Coulometric generation of molybdenum(v)

Molybdenum (V) was generated at a platinum cathode from 0.7 M molybdenum(VI) in 4 M sulfuric acid. A current efficiency of 99.9% was attained. A limiting current density of 0.05 mA/cm²/mM was found. The formal potential of the Mo(VI)–Mo(V) couple in 4 M sulfuric acid was determined to be ca. 0.55 V vs. N.H.E. Chromium(VI) solutions were titrated over a wide range of sample size and generating current. Amperometric titration curves were interpreted from current-voltage curves. Titrations could be performed in the presence of oxygen at the 1μeq. level. The effect of nitrate, perchlorate, orthophosphate, and chloride ions on the titration was determined.     

Electric mass transfer of sodium chloride through cation-exchange membrane MK-40: A rotating membrane disk study

An experimental device consisting of a rotating membrane disk with horizontally positioned cation-exchange membrane MK-40 is described. The device’s design makes it possible to simultaneously obtain current-voltage curves (CVC) and dependences of effective transport numbers for ions of electrolyte and water dissociation products on the current density. Partial CVC are calculated and limiting current densities and diffusion layer thickness are determined at various disk rotation rates. At current densities below the limiting value, the disk’s CVC obey regularities of electrodiffusion kinetics. Upon raising the current density further, the salt ion fluxes increase due to a decrease in the effective diffusion layer thickness, which is caused by the emergence in the near-membrane region of a space charge and electroconvection. At high current densities there occur oscillations of the potential jump that are caused by hydrodynamic instability of the near-membrane solution layer.     

Evaluation of the Zn2+ transport properties through a cation-exchange membrane by chronopotentiometry

In this work the effect of zinc concentration, pH, and boric acid concentration on the zinc transport properties through an IONICS 67-HMR-412 cation-exchange membrane was evaluated. The limiting current density and the transport numbers were determined by means of chronopotentiometry. A model between the limiting current density and the bulk zinc concentration was established, assuming a potential relationship between the zinc transport number through the membrane and the bulk zinc concentration together with the Levich equation for the DBL thickness. A decrease in the initial pH value of the solutions causes considerable modifications both in the plateau region and in the overlimiting current density region of the current–membrane potential curves. The results show that the presence of boric acid produces the precipitation of zinc metaborate on the anodic layer of the cation-exchange membrane.     

Mass transfer examination in electrodialysis using limiting current measurements

The impact of electrodialysis module characteristics on mass transfer was examined using the limiting current method. The current-voltage curves of different electrodialysis modules were measured and limiting currents were determined using the derivative method. The mass transfer coefficients were calculated and the parameters of their dependence on linear flow velocity were estimated. From these the impact of spacer thickness, spacer net type, membrane type, and module geometry were evaluated. It was found that the impact of spacer thickness was almost negligible within the examined range, but a decrease in the mass transfer coefficient could be expected in the case of thicker spacers. By contrast, the spacer net type and type of membrane were found to be very important parameters able to significantly influence the mass transfer. By modifying the module geometry, the mass transfer coefficient could also be altered and, only in this case, the exponential parameter of the dependence was changing. The parameters thus determined may be used to calculate the limiting current in a wide range of operational conditions and may help predict the performance of different electrodialysis module types.     

Heterogeneity of Ion-Exchange Membranes: The Effects of Membrane Heterogeneity on Transport Properties

The heterogeneity of different cation-exchange membranes (Neosepta CMX, Selemion CMV, and HJC heterogeneous membrane) and their effects on transport properties were investigated using chronopotentiometry, membrane conductivity, and current-voltage curves. Modifying the classical Sand equation, a method has been developed to determine the fraction of the conducting region (epsilon) of the ion-exchange membrane. The epsilon values of the CMX, CMV, and HJC membranes were 0.93, 0.95, and 0.75, respectively. Considering the characteristics of each membrane-the CMX and CMV are reinforced homogeneous membranes, while the HJC is a heterogeneous membrane-the epsilon values determined in this study seem to be reasonable. The dependence of membrane conductivities and the limiting current densities on the fraction of conducting region of each membrane have also been studied. Copyright 2001 Academic Press.     

A new electrochemical method for trace water determination in methanol

A new electrochemical method for the determination of trace water in methanol has been developed. This method is based on the effect, that a minor change in the water content affects the value of conductivity measured for dissolved in the solutions electrolyte. The conductivity measurements were performed for four inorganic salts, i.e. NaCl, KCl, RbCl, and CsCl in solutions with different amounts of water traces in methanol and the calibration curves for three of them were determined. With the exception of cesium chloride the high values of correlation coefficients for the regression lines as well as low limits of detection were achieved in all cases which indicates that this method is a useful tool for the determination of the trace amounts of water in methanol.     

Electric mass transport of sodium chloride through cation-exchange membrane MK-40 in dilute sodium chloride solutions: A rotating membrane disk study

The polarization properties of an electromembrane system consisting of an MK-40 membrane and a dilute sodium chloride solution are investigated with an experimental apparatus, which includes a rotating membrane disk with a horizontally positioned membrane. For the electrochemical systems of MK-40/0.01 M NaCl and MK-40/0.001 M NaCl, effective ion transport numbers and partial current-voltage curves are determined for sodium and hydrogen ions, and limiting-current densities and the diffusion-layer thickness are calculated as functions of the rotation rate of the membrane disk. The space-charge distribution in the diffusion layer and in the membrane is calculated for various current densities and rotation rates of the membrane. It is shown that when electric-current densities are greater than the limiting value, ion fluxes of the salt increase as a result of a decrease in the effective thickness of the diffusion layer. This decrease is caused by the development of space charge, electroconvection, water dissociation, and the exaltation effect in the region near the membrane. It has been established that in dilute solutions the limiting current is not purely electrodiffusive in nature.     

一种新型的钛基纳米多孔网状铂电极对甲醇氧化反应的电催化活性

利用水热法一步制备出钛基纳米多孔网状铂催化剂(nanoPt/Ti), 并研究了它对甲醇氧化反应的电催化活性.     

Effect of the Interface Component on Current-voltage Curves of a Composite Bipolar Membrane for Water and Methanol Solutions

The current-voltage curves of a composite bipolar membrane (CBM) were experimentally measured by varying the interface component between cation- and anion-exchange membranes for water and methanol solutions. In each solution system, 0.05 mol/l LiCl was used as the electrolyte. The interface component was varied by pasting the polymers or installing the thin membranes in the intermediate region of the CBM. The measured results show that the functional groups of the polymers and thin membranes enhanced the water and methanol splitting effect. This phenomenon can be explained by the protonation-deprotonation reactions occurring between these functional groups and the water or methanol molecules in the intermediate region of the CBM. The effect of transition metal compounds existing in the intermediate region of the CBM was also experimentally examined in this study. It was found that the effect of transition metal compounds on water or methanol splitting was not obvious. Copyright 1999 Academic Press.     

Effect of the chemical nature of the ionogenic groups of ion-exchange membranes on the size of the electroconvective instability region in high-current modes

The size of the electroconvective instability region on the membrane-solution boundary at currents exceeding the limiting diffusion current was measured by laser interferometry. The influence of the chemical nature of the ionogenic groups of ion-exchange membranes on the development of electroconvective instability was studied. The thickness of the electroconvection region decreased as the catalytic activity of the ionogenic groups of commercial and pilot membrane samples with respect to the heterolytic water dissociation increased. The maximum size of the electroconvective instability region and the minimum currents at which it was recorded for the anion-exchange membranes under study were determined for the highly basic modified anion-exchange membrane MA-41M with an almost completely suppressed water dissociation function. A correlation was found between the size of the convective instability region and the characteristic points on the current-voltage curves.     

Surface charge properties of Fe2O3 in aqueous and alcoholic mixed solvents

Iron oxide (Fe2O3) was identified and characterized by surface area, X-ray diffractometry, and FTIR analyses. Surface charge densities, point of zero charge (PZC), and surface ionization constants were determined from the potentiometric titration data in various aqueous and aqueous organic mixed solvents in the temperature range 293-313 K. The surface charge densities were observed to decrease with the increase in temperature and concentration of metal ions in both the aqueous and aqueous organic mixed solvents. The absolute values of the surface charge density were found to change in the order aqueous > aqueous/methanol > aqueous/ethanol. Further, the PZC of the iron oxide was observed to shift to the higher pH values in the order ethanol > methanol > aqueous solution, which indicated a decrease in the acidity of the surface -OH groups. The pKa1 and pKa2 values of iron oxide were also determined and then used for determination of the surface potential (psi0) of the solid in aqueous and aqueous organic mixed solvents. The surface potential-surface charge curves generally supplemented the results derived from psi0-pH curves.     

Electrochemistry of conductive polymers 38. Electrodeposited poly(3,4-ethylenedioxy-thiophene) studied by current sensing atomic force microscopy

Electrical and morphological properties of poly(3,4-ethylenedioxythiophene) (PEDOT) thin films electrodeposited on gold-on-silicon electrodes by galvanostatic, potentiostatic, and potentiodynamic methods have been determined using current sensing atomic force microscopic experiments. Surface morphologies and vertical conductivities of PEDOT films were affected by the experimental parameters including the preparation method, the current density, the potential, and the potentiodynamic cyclic number. Band gaps obtained from current-voltage curves of dedoped PEDOT were in excellent agreement with those obtained from absorption spectra. When the film thickness was increased on the gold-on-silicon electrode, the topographic images were not very well defined due to the high roughness but conductivities increased significantly in all the galvanostatically, potetiostatically, and potentiodynamically grown PEDOT films.     

Comparative study of a thin-layer cell for analysis of stationary and streaming solutions

A comparative study with a home-built Kissinger-type twin-electrode thin-layer cell has been made, with the cell either filled with quiescent solutions or used as a flow-through detector. In both modes the cell was polarized by a slow linear potential sweep. The current-voltage curves recorded showed a limiting current region in both cases, in spite of the different types of transport process (steady-state diffusion caused by the redox cycling effect of the counter-electrode in the quiescent solution and convective diffusion in the flowing solution). The sensitivities and also the lower detection limits were found to be nearly the same for the two different modes of operation of the same cell, for which an explanation is given. The main analytical advantage of the thin-layer twin-electrode cell filled with quiescent solution is that only a few mul of analyte solution are necessary for the measurement. It was proved experimentally that this type of cell, used as a flow-through detector, gives the expected limiting current, but this current is dependent on the cube root of the linear flow-rate, in agreement with Weber's theoretical prediction, rather than on the square root of the flow-rate (commonly quoted in the literature).     

阳极支撑层憎水性对被动式直接甲醇燃料电池传质性能的影响

通过测定甲醇渗透率,详细研究了阳极支撑层的聚四氟乙烯（PTFE）含量对全被动式直接甲醇燃料电池（DMFC）甲醇传质和电池性能的影响。 膜电极集合体均使用相同的阳极催化层,膜和阴极。 实验结果表明,随着阳极支撑层PTFE含量的提高,甲醇渗透速率明显减小。 其含量较高时,甲醇传质阻力较大,会导致电池在很低的电流密度下就出现传质控制区。 采用PTFE质量分数为40%的支撑层时,DMFC以9 mol/L甲醇为燃料最大功率密度可达32×10-3 W/cm2,也进一步证明了适当提高阳极支撑层的憎水性,既有助于减少甲醇的渗透,又缓解了阴极的“水淹”问题。     

Effects of Electrolytes on the Transport Phenomena in a Cation-Exchange Membrane

The effect of electrolyte solutions on the characteristics of the current-voltage (I-V) curve in a cation-exchange membrane (CMX membrane, Tokuyama Soda, Inc.) was studied based on the concentration polarization and electroconvection theory. The study includes the limiting current density (LCD), plateau length, and the ratio of resistance of region III to region I of the I-V curve (R(3rd)/R(1st)). Different electrolyte solutions, HCl, LiCl, NaCl, KCl, CaCl(2), MgCl(2), and AlCl(3), were used in this study. The LCD values of the electrolytes were correlated with the diffusion coefficient of the cation (D(+)) and valence of the cation and anion (z(+), z(-)). Except for the HCl solution, the LCD values of the electrolytes increased linearly with D(+)(1-z(+)/z(-)), implying that the current in this region was governed by the concentration polarization phenomena. The deviation of the HCl solution from the linearity is due to a particular transport mechanism of the proton called the Grotthuss-type transport. The differences in the plateau length and the resistance ratio, R(3rd)/R(1st), with the electrolytes were explained by the Péclet number (Pe) representing a transport pattern in the electroconvection theory. The Péclet number is proportional to the Stokes radius of an ion. An electrolyte with a large Stokes radius has a shorter plateau length and a lower ratio of R(3rd)/R(1st) than those of an electrolyte with a small Stokes radius. Water-splitting measurements for the different electrolyte solutions in the CMX membrane revealed that the contribution of water splitting to the overlimting current was insignificant regardless of the electrolytes used in this study. However, when metal hydroxides, such as Al(OH)(3), formed on the surface of the membrane, significant water splitting was observed. Copyright 2001 Academic Press.     

Modification of ion-exchange membrane used for separation of protons and metallic cations and characterization of the membrane by current-voltage curves

The ionic transport properties of several cations (H(+), Na(+), and Zn(2+)) across sulfonated ion-exchange membranes modified with an amine were investigated by the measurement of current-voltage curves to determine the effect of the surface modification of the membrane. The membrane was modified by chlorosulfonation and amination with a diamine (N,N-dimethylethylenediamine) and an amine (isoamylamine) to form a sulfonamide bond between amine groups and the surface layer. In the case of the modification with the diamine, the terminal amine was protonated in acidic media or quaternized with methyl iodide. The presence of a positively charged layer on the two sides of the membrane strongly decreased the limiting current flowing across the membrane in the presence of a 1:1 electrolyte such as HCl or HNO(3) due to an increase of the resistance of the membrane. In the case of divalent cations such as Na(+) and Zn(2+), electrostatic repulsion also contributes to the decrease of the limiting current. The presence of divalent anions seems to increase the limiting current somewhat due to their preconcentration within the cationic layer, which facilitates their subsequent transport across the membrane. When only one face of the membrane was modified, the current-voltage measurements showed that the membrane did not behave like a bipolar membrane. For one-side (under forward polarization) and two-side modified membranes, counterions are slightly blocked in the membrane by the cationic layer, which led to a decrease of the membrane conductivity during electrodialysis.     

Solubility and preferential solvation of phenacetin in methanol + water mixtures at 298.15 K

The mole fraction solubility of phenacetin (PNC) in methanol + water binary solvent mixtures at 298.15 K was determined along with density of the saturated solutions. All these solubility values were correlated with the Jouyban–Acree model. Preferential solvation parameters of PNC by methanol (δx_1,3) were derived from their thermodynamic solution properties using the inverse Kirkwood–Buff integrals (IKBI) method. δx_1,3 values are negative in water-rich mixtures but positive in methanol mole fraction of >0.32. It is conjecturable that in the former case the hydrophobic hydration around non-polar groups of PNC plays a relevant role in the solvation. The higher solvation by methanol in mixtures of similar cosolvent compositions and methanol-rich mixtures could be explained in terms of the higher basic behaviour of methanol.     

Charge transfer on porous silicon membranes studied by current-sensing atomic force microscopy

A visible rectification effect on the current-voltage curves of metal/porous silicon/p-silicon has been observed by current-sensing atomic force microscopy. The current-voltage curves of porous silicon membranes with different porosities, prepared through variation of etching current density for a constant time, indicate that a higher porosity results in a higher resistance and thus a lower rectification, until the current reaches a threshold at a porosity 〉55%. We propose that the conductance mode in the porous silicon membrane with porosities 〉55% is mainly a hopping mechanism between nano-crystallites and an inverse static electric field between the porous silicon and p-Si interface blocks the electron injection from porous silicon to p-Si, but with porosities ≤55%, electron flows through a direct continuous channel between nano-crystallites.     

铂纳米晶的合成及其甲醇电催化性能

以草酰胺作为保护剂,采用胶体法合成铂纳米晶,考察了不同溶液pH值、前驱体与保护剂反应物配比对铂纳米晶形貌及其甲醇电催化氧化活性的影响. 测试表明,pH = 5、反应物配比1:20合成的铂纳米晶的甲醇电催化氧化活性最佳,其峰电流密度达到1709 μA·cm^-2. 空气中搁置3个月后,其表面形貌变化不大,但甲醇的电催化活性显著降低. 0.05 ~ 1.2 V电位范围循环扫描100周期,其循环伏安曲线明显变化,晶体表面原子排列方式也发生变化,由易毒化(100)面逐渐转化为(110)面,其甲醇电催化活性增加.