Entrapment and release of sodium polystyrene sulfonate (SPS) from calcium alginate gel beads

The release of sodium polystyrene sulfonate (SPS) from calcium alginate hydrogel beads has been studied. It has been shown that the structure of the cross-linked calcium alginate network is of primary importance in the retention and/or release of the SPS. This has been evidenced by studying the influence of Ca²⁺ concentration, molar masses (M_n) and the ratio of mannuronic acid/guluronic acid components. A minimum in the SPS release is observed in relation with the organization of the network structure. Conditions inducing the organization of a strong gel (e.g. high Ca²⁺ concentration for example) are not always related to a low release. A good control of release is found when a compromise between a well-structured hydrogel and sterical consideration of SPS is reached.     

Drug release of pH/temperature-responsive calcium alginate/poly(N-isopropylacrylamide) semi-IPN beads

A series of semi-interpenetrating, polymer network (semi-IPN), hydrogel beads, composed of calcium alginate (Ca-alginate) and poly(N-isopropylacrylamide) (PNIPAAM), were prepared for a pH/temperature-sensitive drug delivery study. The equilibrium swelling showed the independent pH- and thermo- responsive nature of the developed materials. At pH=2.1, the release amount of indomethacin incorporated into these beads was about 10% within 400 min, while this value approached to 95% at pH=7.4. The release rate of the drug was higher at 37 degrees C than that at 25 degrees C and increased slightly with increasing PNIPAAM content. These results suggest that the Ca-alginate/PNIPAAM beads have the potential to be used as an effective pH/temperature sustainable delivery system of bioactive agents. [GRAPHS: SEE TEXT] A summary of the temperature- and pH-dependence on the release of the drug over a period of 450 min. The effect of the temperature on the swelling of the beads is shown in the inset.     

Miscibility and orientation behavior of poly(vinyl alcohol) / poly(vinyl pyrrolidone) blends

The miscibility of poly(viny1 alcohol)/poly(vinyl pyrrolidone) (PVA/PVP) blends is investigated by differential scanning calorimetry (DSC) and wide-angle x-ray diffraction (WAXD). The molecular orientation induced by uniaxial stretching of the blends is also examined by WAXD and birefringence measurements. It is shown by the DSC thermal analysis that the polymer pair is miscible, since a single glass transition temperature (T_g) is situated between the T_gs of the two homopolymers at every composition. The T_g versus composition curve does not follow a monotonic function but exhibits a cusp point at a PVP volume fraction of a little under 0.7, as in a case predicted by Kovacs' theory. The presence of a specific intermolecular interaction between the two polymers is suggested by an observed systematic depression in the melting point of the PVA component. A negative value of the polymer-polymer interaction parameter, χ₁₂ = 0.35 (at 513 K), is estimated from a thermodynamic approach via a control experiment using samples crystallized isothermally at various temperatures. The extent of optical birefringence (Δn) of the drawn blends decreases drastically with increasing PVP content up to 80 wt %, when compared at a given draw ratio, and ultimately Δn is found to change from positive to negative at a critical PVP concentration of a little over 80 wt %. Discussion of the molecular orientation behavior takes into consideration a birefringence compensation effect in the miscible amorphous phase due to positive and negative contributions of oriented PVA and PVP, respectively.     

Heterotactic poly(vinyl alcohol)

Bulky substituents in vinyl trialkylsilyl ethers and vinyl trialkylcarbinyl ethers led to heterotactic polymers (H = 66%). The polymers were converted into poly(vinyl alcohol) (PVA) and further to poly(vinyl acetate), and tacticity was determined as poly(vinyl acetate). Vinyl triisopropylsilyl ether in nonpolar solvents yielded a heterotactic polymer with a higher percentage of isotactic triads than syndiotactic triads (Hetero-I). Vinyl trialkylcarbinyl ethers in polar solvents gave a heterotactic polymer with more syndiotactic triads than isotactic (Hetero-II). Heterotactic PVA was soluble in water and showed characteristics infrared absorptions. Interestingly, Hetero-I PVA showed no iodine color reaction, but Hetero-II showed a much more intense color reaction than a commercial PVA. The mechanism of heterotactic propagation was discussed in terms of the Markóv chain model.     

Extended release of Gliclazide from highly stabilized calcium alginate/poly(acrylamide) beads for diabetes management

In the present work, stability of calcium alginate beads has been remarkably improved by a novel strategy which consists of in situ formation of poly (acrylamide) within the calcium ions cross-linked sodium alginate beads. The resulting beads have been found to be stable for more than 48 h, in the physiological fluid (PF) of pH 7.4, while the plain alginate beads disintegrated within a couple of hours. The release of the anti-diabetic drug Gliclazide (Glz) from the beads was investigated under physiological conditions. The enhanced stability and prolonged release was also confirmed by an in vivo study on Albino Wistar rats.     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). II. Polymerization of vinyl acetate in the presence of crosslinked poly(vinyl alcohol)

It is a common view that poly(vinyl acetate) has many branches at the acetyl side group, but that the corresponding poly(vinyl alcohol) has little branching. In order to study the branching in poly(vinyl acetate) and poly(vinyl alcohol) which is formed by chain transfer to polymer, the polymerization of ¹⁴C-labeled vinyl acetate in the presence of crosslinked poly(vinyl acetate), which was able to be decrosslinked to give soluble polymers, was investigated at 60°C and 0°C. This system made it possible to separate as well as to distinguish the graft polymer from the newly polymerized homopolymer. Furthermore, the degree of grafting onto the acetoxymethyl group and onto the main chain were estimated. It became clear that, in the polymerization of vinyl acetate, chain transfer to the polymer main chain takes place about 2.4 times as frequently at 60°C as that to the acetoxy group and about 4.8 times as frequently at 0°C.     

Entrapment of glucose oxidase in non-porous poly(vinyl chloride)

We have used solvent casting techniques to immobilise glucose oxidase (GOD) within unplasticised and plasticised poly(vinyl chloride) (PVC) matrices. The plasticisers studied were the cationic surfactant, tricaprylmethylammonium chloride (Aliquat 336s), the anionic surfactant bis(2-ethylhexyl) hydrogenphosphate (BEP) and the lipid, isopropylmyristate (IPM). The activity of the enzyme-membrane was tested by amperometric electrode. Changes in enzyme-membrane electrode response are rationalised on the basis of membrane permselective properties. The Aliquat and IPM modified PVC membranes gave amplified signals due to better retention and subsequent concentration of the H₂O₂ signal species. Effectively, less was being lost to the bulk solution. In the case of the BEP-modified membrane, while there was a linear step change in response up to 50 mM, at higher concentrations, responses did not reach steady-state; they were characterised by an upward drift in response of 0.050 nA/min. This characteristic is thought to be due to a build up of gluconic acid resulting in a pH reduction in the membrane microenvironment and hydrogen bonding between neighbouring BEP molecules. Under these conditions, we have previously shown that the membrane permeability to hydrophilic species is attenuated and it is tentatively suggested that the upward drift due to the build up of H₂O₂ on the electrode side with less permeating through the acidified membrane into bulk solution.The results were compared against using variously plasticised PVC (but no enzyme entrapped) as an outer membrane of a classical dual-membrane glucose enzyme electrode construct. In the latter case, the enzyme was chemically crosslinked between the membranes using glutaraldehyde.     

Temperature-sensitive poly(vinyl methyl ether) hydrogel beads

Temperature-sensitive hydrogel beads were prepared by radiation crosslinking of poly(vinyl methyl ether) PVME spheres wrapped in Ca-alginate. The obtained gel beads have diameters in the sub-millimeter or millimeter range (depending on the PVME concentration). They were characterized by sol-gel analysis, swelling measurements, and differential scanning calorimetry. The gel content g increases with increasing radiation dose D. The swelling degree Q_v decreases with increasing PVME concentration c_p and increasing D. In comparison to PVME bulkgels the phase-transition temperature of the synthesized PVME gel beads is a little decreased.     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

Structural irregularities in poly(vinyl alcohol)

Poly(vinyl alcohols) derived from the product of polymerization of vinyl acetate in methanol have been characterized by various physical and chemical methods before and after NaIO₄ cleavage. The 220-MHz ¹H-NMR spectra confirm the reliability of NaIO₄ titrimetry for estimating 1,2-glycol content and help explain the tendency for viscometry to grossly underestimate the 1,2-glycol content for low molecular weight polymers. The spectra and related chemical evidence indicate that the major endgroups are HOCH₂CH₂? and CH₃CH(OH)CH(OH)CH₂? . ß-Hydroxyethyl groups also occur as short chain branches, mainly attached to α carbon atoms in the normal head-to-tail polymer chain sequence. The concentrations of the branch and endgroups depend on polymerization conditions and help explain polymerization “solvent” effects on physical properties.     

Preparation and characterization of monodisperse superparamagnetic poly(vinyl alcohol) beads by reverse spray suspension crosslinking

A novel protocol for preparing magnetic poly(vinyl alcohol) (PVA) beads by reverse spray suspension crosslinking was reported. The hydrophilic Fe₃O₄ nanoparticles were mixed with PVA, glutaraldehyde, and water to form aqueous phase. Then the aqueous phase was sprayed into vegetable oil by a pressure of nitrogen gas to form water in oil (W/O) suspension. The magnetic PVA beads were obtained in the presence of hydrochloric acid catalyst. It was found that the magnetic PVA beads obtained good properties when the PVA concentration was 10%, and the oil phase temperature was controlled at 40 °C. The mechanical stirring has little impact on the size of magnetic PVA beads in the process of reverse spray suspension crosslinking. The Cibacron Blue (CB) was coupled on the surface of magnetic PVA beads by surface chemical reaction. The morphology, size, and magnetic properties of the magnetic PVA beads were examined by scanning electron microscopy, laser diffraction, and vibrating sample magnetometer, respectively. Compared with the stirring method, it was found that the size of magnetic PVA beads was monodisperse and their saturation magnetization was much higher. Fourier transform infrared and X‐ray photoelectron spectroscopy experimental results proved that CB molecules were covalently immobilized onto the surface of the magnetic PVA beads. Meanwhile, the protein affinity separation experiments demonstrated that the magnetic PVA beads can potentially be used as a carrier for large‐scale protein separation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 203–210, 2008     

Impedance spectroscopy of chitosan/poly(vinyl alcohol) films

Journal of Solid State Electrochemistry - Polymer films were cast from aqueous solutions of chitosan (CS) and poly(vinyl alcohol) (PVA) in employing tetraethoxysilane (TEOS) as a crosslinking...     

Preparation of electrospun chitosan/poly(vinyl alcohol) membranes

Electrospinning of chitosan from its solutions in 2% aqueous acetic acid was studied by adding poly(vinyl alcohol) (PVA) as a “guest” polymer. Properties of the chitosan/PVA solutions including viscosity, conductivity, and surface tension were measured, and effects of the polymer concentration, chitosan/PVA mass ratio and processing parameters (applied voltage, flow rate, capillary-to-collector distance) on the electrospinnability of chitosan/PVA were investigated. Analyses of scanning electron micrographs and transmission electron micrographs suggested that the chitosan/PVA ultrafine fibers were often obtained along with beads, and chitosan was located in the elctrospun fibers as well as in the beads. Uniform chitosan/PVA fibers with an average diameter of 99 ± 21 nm could be prepared from a 7% chitosan/PVA solution in 40:60 mass ratio. Results of Fourier transform infrared spectroscopy and X-ray diffraction demonstrated that there were possible hydrogen bonds between chitosan and PVA molecules, which could weaken the strong interaction in chitosan itself and facilitate chitosan/PVA electrospinnability. The electrospun chitosan/PVA membranes showed higher water uptake and would have potential applications in wound dressings.     

Release property of temperature-sensitive alginate beads containing poly(N-isopropylacrylamide)

The graft copolymer (APN) of alginate and poly(N-isopropylacrylamide) (PNIPAM) were synthesized and APN beads were prepared by dropping the aqueous solution of the copolymer into an aqueous solution of Ca(2+) solution. Alginate chains were employed to play a role in forming beads by electrostatic interactions with a multivalent ion, Ca(2+). Grafted PNIPAM segments were adopted to act as a valve for the pores of the beads, since they exhibit the properties of thermal contraction and expansion. The percent of release of blue dextran from APN beads was higher at 40 degrees C than at 25 degrees C. The difference in the release between two temperatures became more distinguishable when the content of PNIPAM in APN beads is higher. Below lower critical solution temperature (LCST), the expanded PNIPAM would close the pores of the beads, resulting in a lower release rate. Above LCST, the thermally contracted polymer would open the pores, resulting in a higher release rate. The percent of release from APN beads were investigated when the temperature of the release medium is altered. The release rate was relatively low at 25 degrees C. The temperature, however, changed up to 40 degrees C, a marked increase in the release rate was observed. These trends were found to be reproducible when the temperature was repeatedly altered between 25 and 40 degrees C. As a result, a stepwise response to the temperature alteration was obtained.     

The solvation of poly(vinyl alcohol)

The possible incorporation of water molecules within the crystal structure of poly(vinyl alcohol) is discussed. Modelling of the crystal structure suggested that water could be incorporated without severe disruption, and the effect on the X-ray powder diffraction trace was simulated. The effect of variation in tacticity is discussed in terms of the nature of the hydrogen bonding. Simulated traces are compared with experimental data from atactic samples in which a change in the diffraction peak intensities is observed for samples crystallised with water present. This is compared with samples produced from nonaqueous solutions.     

Study of the miscibility of poly(vinyl pyridines) with poly(vinyl acetate), poly(vinyl alcohol) and their copolymers

Miscibility of poly(4-vinyl pyridine) (P4VP) and poly(2-vinyl pyridine) (P2VP) with poly(viny acetate) (PVAc), poly(vinyl alcohol) PVA and poly(vinyl acetate-co-alcohol) (ACA copolymers) has been investigated over a wide composition range. Differentiaal scanning calorimetry (DSC) results indicate that P2VP is immiscible with PVAC, PVA, and their copolymers over the whole composition range. In turn, P4VP appears to be immiscible with PVAC and PVA, but miscible with some ACA copolymers in certain range of composition. The P4VP-ACA phase diagram for different copolymer compositions has been determined. The variation of the glass transition temperature with composition for miscible mixtures was found to follow the Gordon-Taylor equation, with the parameter κ dependent upon copolymer composition. FTIR analysis of blends reveal the existence of specific interactions via hydrogen bonding between hydroxyl groups and the nitrogen of the pyridinic ring, which appear to be decisive for miscibility. © 1994 John Wiley & Sons, Inc.     

Dynamic mechanical and dielectrical properties of poly(vinyl alcohol) and poly(vinyl alcohol)‐based nanocomposites

In this article we report on the investigation of the dynamics of poly(vinyl alcohol) (PVA) and PVA‐based composite films by means of dielectric spectroscopy and dynamic mechanical thermal analysis. Once the characterization of pure PVA was done, we studied the effect of a nanostructured magnetic filler (nanosized CoFe₂O₄ particles homogeneously dispersed within a sulfonated polystyrene matrix) on the dynamics of PVA. Our results suggest that the α‐relaxation process, corresponding to the glass transition of PVA, is affected by the filler. The glass‐transition temperature of PVA increases with filler content up to compositions of around 10 wt %, probably as a result of polymer–filler interactions that reduce the polymer chain mobility. For filler contents higher than 10 wt %, the glass‐transition temperature of PVA decreases as a result of the absorption of water that causes a plasticizing effect. The β‐ and γ‐relaxation processes of PVA are not affected by the filler as stated from both dynamic mechanical thermal analysis and dielectric spectroscopy. Nevertheless, both relaxation processes are greatly affected by the moisture content. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1968–1975, 2001     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). I. Crosslinking and crosslinking cleavage of poly(vinyl acetate)

A crosslinked network was formed by the reaction of partially saponified poly(vinyl acetate) and toluylene diisocyanate in benzene. The yield of gel was markedly dependent on the degree of saponification and the concentrations of polymer and diisocyanate. Crosslinked poly(vinyl alcohol) was obtained by treating the poly(vinyl acetate) with a catalytic amount of sodium hydroxide in methanol without any change of the urethane crosslinks. The crosslink based on the urethane linkage was quantitatively cleaved by acids, especially by hydrobromic acid, releasing polymers of the same molecular weight as the original.     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998