Pressurized liquid extraction using water/isopropanol coupled with solid-phase extraction cleanup for industrial and anthropogenic waste-indicator compounds in sediment

A broad range of organic compounds is recognized as environmentally relevant for their potential adverse effects on human and ecosystem health. This method was developed to better determine the distribution of 61 compounds that are typically associated with industrial and household waste as well as some that are toxic and known (or suspected) for endocrine-disrupting potential extracted from environmental sediment samples. Pressurized liquid extraction (PLE) coupled with solid-phase extraction (SPE) was used to reduce sample preparation time, reduce solvent consumption to one-fifth of that required using dichloromethane-based Soxhlet extraction, and to minimize background interferences for full scan GC/MS analysis. Recoveries from spiked Ottawa sand, commercially available topsoil, and environmental stream sediment, fortified at 4-720 μg per compound, averaged 76 ± 13%. Initial method detection limits for single-component compounds ranged from 12.5 to 520 μg/kg, based on 25 g samples. Results from 103 environmental sediment samples show that 36 out of 61 compounds (59%) were detected in at least one sample with concentrations ranging from 20 to 100,000 μg/kg. The most frequently detected compound, beta-sitosterol, a plant sterol, was detected in 87 of the 103 (84.5%) environmental samples with a concentration range 360-100,000 μg/kg. Results for a standard reference material using dichloromethane Soxhlet-based extraction are also compared.     

Chemical composition of bioactive pressurized extracts of Romanian aromatic plants

In this contribution, pressurized liquid extraction (PLE) has been employed to isolate bioactive compounds from three native Romanian plants, oregano (Origanum vulgare), tarragon (Artemisia dracunculus) and wild thyme (Thymus serpyllum). Different PLE conditions have been tested including extraction with water, ethanol and their mixtures in a wide range of extraction temperatures (50-200°C), and the antioxidant capacity of the extracts was measured using different assays (DPPH radical scavenging, TEAC assay and Folin-Ciocalteau assay to measure total phenols). Moreover, a complete chemical characterization by using LC-MS/MS was carried out to be able to correlate the bioactivity with the particular chemical composition of each extract and plant. The use of PLE with water as a solvent at the highest temperature tested (200°C) always provided the highest extraction yields for the three studied plants, being maximum for oregano (>60%). Besides, oregano's pressurized water extracts at lower temperatures (50°C) presented the highest content on total phenols (184.9 mg gallic acid/g extract) and the best antioxidant activities (EC(50) 6.98 μg/ml). In general, oregano extracts were the most active, followed by wild thyme extracts. The antioxidant capacity measured by DPPH assay was highly correlated with the amount of total phenols. Moreover, the use of a LC-MS/MS method allowed the identification of 30 different phenolic compounds in the different extracts, including phenolic acids, flavones, flavanones and flavonols, which have an important influence on the total antioxidant capacity of the different extracts.     

Extraction of polycyclic aromatic hydrocarbons from smoked fish using pressurized liquid extraction with integrated fat removal

Quantification of polycyclic aromatic hydrocarbons (PAHs) in smoked fish products often requires multiple clean-up steps to remove fat and other compounds that may interfere with the chemical analysis. We present a novel pressurized liquid extraction (PLE) method that integrates exhaustive extraction with fat retention in one single analytical step. The PLE parameters: type of fat retainer, flush volume, solvent composition, fat-to-fat retainer ratio (FFR), and the dimensions of the extraction cells were the most important factors for obtaining fat-free extracts with high recoveries of PAHs. A 100 mL extraction cell filled with 18 g activated silica gel, dichloromethane:hexane (15:85, v/v) as extraction solvent, FFR of 0.025 and 100% flush volume was the best analytical setup for integrated extraction and fat retention.The one-step procedure provided a more rapid and cost-efficient alternative with minimization of waste generation compared to the standard reference method that is based on a multi-step procedure. Furthermore, the analytical quality of the two methods are comparable, while the new integrated approach for extraction and cleanup is less prone to analytical errors (random and systematic) because of fewer analytical steps.     

Determination of Polybrominated Diphenyl Ethers in Coastal and River Sediments by Pressurized Liquid Extraction Coupled with Gas Chromatography‐Mass Spectrometry

This study presents a time‐ and solvent‐saving method, pressurized liquid extraction (PLE), to extract polybrominated diphenyl ethers (PBDEs) in sediment samples. The effects of various operating parameters (i.e., extraction solution, temperature, pressure, static/dynamic extraction times) for the quantitative extraction of PBDEs by home‐made PLE were systematically investigated and optimized. The analytes were then identified and quantitated by gas chromatography‐mass spectrometry (GC‐MS) in selected ion monitoring (SIM) mode. The 16 PBDE congeners (from tri‐ to deca‐BDE) can be completely extracted by dichloromethane: n‐hexane (3/2, v/v) at 100 °C and 100 atm combined with 15 min static and then 15 min dynamic extraction steps. Recovery of PBDEs in spiked sediment samples ranged from 52 to 104% with 2‐16% RSD, except for BDE‐206. Limits of quantitation (LOQ) were established between 4 and 400 pg/g (dry weight) in 10 g of sediment sample. The extraction efficiency of the PLE was also compared with the traditional Soxhlet extraction method. The total contents of PBDEs ranged from 8.0 to 37.9 ng/g (dry weight) in various river and coastal sediment samples in Taiwan. Deca‐BDE (BDE‐209) was the major PBDE detected in these sediment samples.     

Clean-up techniques in the pressurized liquid extraction of abiotic environmental solid samples

Pressurized liquid extraction (PLE) uses high pressure and temperature to perform exhaustive extraction and is one of the extraction techniques widely used for determining contaminants in environmental solid samples. However, under these conditions, compounds from the matrix are also extracted. Therefore, clean-up strategies must be often applied to remove interferences and avoid matrix effect in the subsequent determination. There are different clean-up strategies that can be used in PLE, some of which are applied during the extraction procedure and some are applied to the PLE extract. The aim of this review is to critically discuss these clean-up techniques used in PLE of abiotic environmental solid samples in the last 10 years. We provide the readers with information about the weaknesses and strengths of each strategy so they can select the most suitable clean-up technique for a specific environmental analytical problem.     

Determination of pharmaceuticals in environmental and biological matrices using pressurised liquid extraction—Are we developing sound extraction methods?

Pressurised liquid extraction (PLE) is now a well established and extensively applied extraction technique in environmental analysis for pollutants such as persistent organic pollutants (POPs). During the past decade, an emerging group of environmentally interesting analytes are pharmaceuticals that are continuingly released into the environment. This class is comprised with compounds of various properties. As the field of the analysis of these compounds grows, an increasing number of PLE methods for pharmaceuticals of varying quality are developed and published. This review summarises the critical PLE parameters during PLE method development and highlight them with examples from recently published papers utilising pressurised liquid extraction for the determination of pharmaceuticals in environmental and biological matrices. These recent methods are summarised and critically discussed with the aim to provide important reflections to alleviate in future PLE development for pharmaceuticals in environmental matrices.     

Troubleshooting with cell blanks in PLE extraction

The blank extracts obtained from the pressurized liquid extraction (PLE) of a 11 mL empty cell of ASE 200 were analysed by GC-FID and GC-ECD and many interfering peaks were detected, which could difficult the trace analysis of persistent organic pollutants (i.e. polycyclic aromatic hydrocarbons, aliphatic hydrocarbons and organochlorine pesticides). These interfering compounds were identified as phthalates, silicones and organic acids and their sources were established. A solution to this analytical trouble is a previous extraction step of the empty cell under the same conditions optimised for the sample extraction.     

Pressurized liquid extracts from Spirulina platensis microalga. Determination of their antioxidant activity and preliminary analysis by micellar electrokinetic chromatography

In this work, different extracts from the microalga Spirulina platensis are obtained using pressurized liquid extraction (PLE) and four different solvents (hexane, light petroleum, ethanol and water). Different extraction temperatures (115 and 170 degrees C) were tested using extraction times ranging from 9 to 15 min. The antioxidant activity of the different extracts is determined by means of an in vitro assay using a free radical method. Moreover, a new and fast method is developed using micellar electrokinetic chromatography with diode array detection (MEKC-DAD) to provide a preliminary analysis on the composition of the extracts. This combined application (i.e., in vitro assays plus MEKC-DAD) allowed the fast characterization of the extracts based on their antioxidant activity and the UV-vis spectra of the different compounds found in the extracts. To our knowledge, this work shows for the first time the great possibilities of the combined use of PLE-in vitro assay-MEKC-DAD to investigate natural sources of antioxidants.     

Optimizing pressurized liquid extraction of microbial lipids using the response surface method

Response surface methodology (RSM) was used for the determination of optimum extraction parameters to reach maximum lipid extraction yield with yeast. Total lipids were extracted from oleaginous yeast (Rhodotorula glutinis) using pressurized liquid extraction (PLE). The effects of extraction parameters on lipid extraction yield were studied by employing a second-order central composite design. The optimal condition was obtained as three cycles of 15 min at 100°C with a ratio of 144 g of hydromatrix per 100 g of dry cell weight. Different analysis methods were used to compare the optimized PLE method with two conventional methods (Soxhlet and modification of Bligh and Dyer methods) under efficiency, selectivity and reproducibility criteria thanks to gravimetric analysis, GC with flame ionization detector, High Performance Liquid Chromatography linked to Evaporative Light Scattering Detector (HPLC-ELSD) and thin-layer chromatographic analysis. For each sample, the lipid extraction yield with optimized PLE was higher than those obtained with referenced methods (Soxhlet and Bligh and Dyer methods with, respectively, a recovery of 78% and 85% compared to PLE method). Moreover, the use of PLE led to major advantages such as an analysis time reduction by a factor of 10 and solvent quantity reduction by 70%, compared with traditional extraction methods.     

Determination of multiclass pesticides in food commodities by pressurized liquid extraction using GC–MS/MS and LC–MS/MS

Pressurized liquid extraction (PLE) was applied to the simultaneous extraction of a wide range of pesticides from food commodities. Extractions were performed by mixing 4 g of sample with 4 g of Hydromatrix and (after optimization) a mixture of ethyl acetate:acetone (3:1, v/v) as extraction solvent, a temperature of 100°C, a pressure of 1000 psi and a static extraction time of 5 min. After extraction, the more polar compounds were analyzed by liquid chromatography (LC), and the apolar and semipolar pesticides by gas chromatography (GC); in both cases LC and GC were coupled with mass spectrometry in tandem (MS/MS) mode. The overall method (including the PLE step) was validated in GC and LC according to the criteria of the SANCO Document of the European Commission. The average extraction recoveries (at two concentration levels) for most of the analytes were in the range 70–80%, with precision values usually lower than 15%. Limits of quantification (LOQ) were low enough to determine the pesticide residues at concentrations below or equal to the maximum residue levels (MRL) specified by legislation. In order to assess its applicability to the analysis of real samples, aliquots of 15 vegetable samples were processed using a conventional extraction method with dichloromethane, and the results obtained were compared with the proposed PLE method; differences lower than 0.01 mg kg⁻¹ were found.     

Separation and characterization of antioxidants from Spirulina platensis microalga combining pressurized liquid extraction, TLC, and HPLC-DAD

A new procedure has been developed to separate and characterize antioxidant compounds from Spirulina platensis microalga based on the combination of pressurized liquid extraction (PLE) and different chromatographic procedures, such as TLC, at preparative scale, and HPLC with a diode array detector (DAD). Different solvents were tested for PLE extraction of antioxidants from S. platensis microalga. An optimized PLE process using ethanol (generally recognized as safe, GRAS) as extraction solvent has been obtained that provides natural extracts with high yields and good antioxidant properties. TLC analysis of this ethanolic extract obtained at 115 degrees C for 15 min was carried out and the silica layer was stained with a DPPH (diphenyl-pycril-hydrazyl) radical solution to determine the antioxidant activity of different chromatographic bands. Next, these colored bands were collected for their subsequent analysis by HPLC-DAD, revealing that the compounds with the most important antioxidant activity present in Spirulina extracts were carotenoids, as well as phenolic compounds and degradation products of chlorophylls.     

Pressurized liquid extraction of mate tea leaves

The objective of this work is to investigate the influence of process parameters on the pressurized liquid extraction (PLE) of Ilex paraguariensis leaves. A factorial 2⁶⁻² experimental design was employed using responses as the extraction yield and the chromatographic profile of the extracts. The extraction time, polarity of solvent, amount of sample, numbers of PLE cycles, flushing volume and extraction temperature were selected as independent variables (factors). Results obtained indicated that the solvent polarity was the most significant variable in the study, while the amount of sample and extraction temperature also showed significant effect. The other variables did not present significant influence in the yield of extraction. GC/MS analysis of the extract enabled the identification of saturated hydrocarbons, fatty acids, fatty acid methyl esters, phytosterols and theobromine in the extracts. Quantitative analysis of four compounds presented in the extracts (caffeine, phytol, vitamin E and squalene) was performed by the GC/MS in the SIM mode.     

Pressurized solvent extraction followed by gas chromatography tandem mass spectrometry for the determination of benzotriazole light stabilizers in indoor dust

A novel and sensitive method for the determination of five benzotriazole compounds (commonly used as light stabilizers) in indoor dust is presented. Pressurized liquid extraction (PLE) and gas chromatography followed by tandem in time mass spectrometry (GC–MS/MS) were used as sample preparation and determination techniques, respectively. Extraction and clean-up were integrated on-line and, after an evaporative concentration step, the extract provided by the PLE instrument was injected directly in the GC–MS/MS system. Parameters affecting the performance of the sample preparation process were evaluated using experimental factorial designs. Under optimized conditions, analytes were recovered from 0.5 g samples in 3 static extraction cycles of 10 min, using a hexane:dichloromethane (7:3) mixture, at 90 °C. Silica (1 g) was placed in the bottom of the extraction cells as clean-up sorbent. The recoveries of the method varied from 82 to 122%, with standard deviations below 13. The inter-day precision ranged from 9 to 12%, and the limits of quantification (LOQs) remained below 10 ng g⁻¹ for all species. For the first time, four of the five investigated species were found in dust from indoor environments. Their mean concentrations ranged from 71 to 780 ng g⁻¹.     

Optimization of pressurized liquid extraction and purification conditions for gas chromatography-mass spectrometry determination of UV filters in sludge

This work presents an effective sample preparation method for the determination of eight UV filter compounds, belonging to different chemical classes, in freeze-dried sludge samples. Pressurized liquid extraction (PLE) and gas chromatography-mass spectrometry (GC-MS) were selected as extraction and determination techniques, respectively. Normal-phase, reversed-phase and anionic exchange materials were tested as clean-up sorbents to reduce the complexity of raw PLE extracts. Under final working conditions, graphitized carbon (0.5 g) was used as in-cell purification sorbent for the retention of co-extracted pigments. Thereafter, a solid-phase extraction cartridge, containing 0.5 g of primary secondary amine (PSA) bonded silica, was employed for off-line removal of other interferences, mainly fatty acids, overlapping the chromatographic peaks of some UV filters. Extractions were performed with a n-hexane:dichloromethane (80:20, v:v) solution at 75°C, using a single extraction cycle of 5 min at 1500 psi. Flush volume and purge time were set at 100% and 2 min, respectively. Considering 0.5 g of sample and 1 mL as the final volume of the purified extract, the developed method provided recoveries between 73% and 112%, with limits of quantification (LOQs) from 17 to 61 ng g(-1) and a linear response range up to 10 μg g(-1). Total solvent consumption remained around 30 mL per sample. The analysis of non-spiked samples confirmed the sorption of significant amounts of several UV filters in sludge with average concentrations above 0.6 μg g(-1) for 3-(4-methylbenzylidene) camphor (4-MBC), 2-ethylhexyl-p-methoxycinnamate (EHMC) and octocrylene (OC).     

Pressurized liquid extraction of isoflavones from soybeans

Isoflavone derivatives from freeze-dried soybeans were extracted by pressurized liquid extraction (PLE) and determined by reverse-phase high performance liquid chromatography (HPLC) with both photo diode array and mass spectrometry (MS) detection. Both real and spiked samples were used in the development of the method.Several extraction solvents (methanol (MeOH) and ethanol (EtOH), 30-80% in water and water), temperatures (60-200 °C), pressures (100-200 atm), as well as the sample size (0.5-0.05 g) and cycle length (5-10 min) were studied for the optimization of the extraction protocol. The optimized extraction conditions for quantitative recoveries were: 0.1 g of sample, 100 °C, three (7 min) static extraction cycles and ethanol 70% as extracting solvent. The stability of the isoflavones during the PLE was also determined. Under PLE conditions, degradation of malonyl glucoside forms of the isoflavones takes place using temperatures higher than 100 °C whereas degradation of glucosides takes place above 150 °C. Using the optimized protocol, isoflavones can be extracted from freeze-dried soybeans without degradation.     

Bixin extraction from defatted annatto seeds

Bixin is the major carotenoid in the seed of the Annatto plant (Bixa orellana L.). The aim of this study was to obtain extracts containing bixin from seeds that had been partially defatted by supercritical fluid extraction. Pressurized liquid extraction (PLE) and low-pressure solvent extraction (LPSE) methods were used, and the effects of the solvent, temperature, pressure, solvent mass to feed mass (S/F) ratio and ultrasonication were evaluated for the global yield (X₀(%)) and the bixin yield (BY(%)). Extraction conditions producing high yields of bixin were established for both the PLE and LPSE methods. Analysis of variance was used to examine the influence of the individual extraction variables in LPSE and PLE. For LPSE; significant effects were found for solvent, temperature, and the interactions of temperature with solvent and temperature with S/F. Solvent was the only variable that significantly affected X₀(%) and BY(%), for PLE. While ultrasonication did not significantly affect X₀(%) or BY(%), scanning electron microscopy analysis revealed structural changes in the vegetal matrix following this treatment.     

Multi-residue method for trace level determination of pharmaceuticals in solid samples using pressurized liquid extraction followed by liquid chromatography/quadrupole-linear ion trap mass spectrometry

A simple and sensitive method for simultaneous analysis of 43 pharmaceutical compounds in sewage sludge and sediment samples was developed and validated. The target compounds were extracted using pressurized liquid extraction (PLE) and then purified and pre-concentrated by solid phase extraction (SPE) using a hydrophilic-lipophilic balanced polymer. PLE extraction was performed on temperature of 100 °C, with methanol/water mixture (1/2, v/v) as extraction solvent. The quantitative analysis was performed by liquid chromatography tandem mass spectrometry using a hybrid triple quadrupole-linear ion trap mass spectrometer (LC-QqLIT-MS). Data acquisition was carried out in selected reaction monitoring (SRM) mode, monitoring two SRM transitions to ensure an accurate identification of target compounds in the samples. Additional identification and confirmation of target compounds were performed using the Information Dependent Acquisition (IDA) function. The method was validated through the estimation of the linearity, sensitivity, repeatability, reproducibility and matrix effects. The internal standard approach was used for quantification because it efficiently corrected matrix effects. Despite the strong matrix interferences, the recoveries were generally higher of 50% in both matrixes and the detection and quantification limits were very low. Beside the very good sensitivity provided by LC-QqLIT-MS, an important characteristic of the method is that all the target compounds can be simultaneously extracted, treated and analysed. Hence, it can be used for routine analysis of pharmaceuticals providing large amount of data. The method was applied for the analysis of pharmaceuticals in river sediment and wastewater sludge from three treatment plants with different treatment properties (i.e. capacity, secondary treatment, quality of influent waters). The analysis showed a widespread occurrence of pharmaceuticals in the sludge matrices.     

Determination of pesticides in milk-based infant formulas by pressurized liquid extraction followed by gas chromatography tandem mass spectrometry

An efficient and selective automated analytical method for the determination and quantification of a selected group of 12 organochlorine and organophosphorous pesticides in milk-based infant formulas has been developed. The samples were extracted by pressurized liquid extraction (PLE) and analysed using GC-MS/MS. The use of alumina as the fat retainer in the PLE extraction cell, together with the application of an injector temperature program during the GC injection process, avoided typical matrix interferences without the application of additional cleanup steps. Mean recoveries of between 70 and 110% were achieved for most of the compounds, except for chlorpyrifos methyl (50%), vinclozoline (48%), fenitrothion (56%) and procymidone (53%), with relative standard deviations ranging from 9 to 17%. Low limits of quantification were obtained for the studied compounds, from 0.01 to 2.6 μg kg⁻¹, thus guaranteeing their accurate determination within the rigorous requirements established for baby food. The validated method was applied to a pilot monitoring study in Spain. Twenty five samples of different brands of powdered infant formulas were obtained from supermarkets. Positive findings of endosulfan I, endosulfan II, fenitrothion, chlorpyrifos ethyl and bifenthrin were detected at concentrations ranging from 0.03 to 5.03 μg kg⁻¹.     

Chemical composition of mate tea leaves (Ilex paraguariensis): a study of extraction methods

The objective of this work was to investigate the extraction of Ilex paraguariensis leaves by means of three extraction techniques: pressurized liquid extraction (PLE, also called accelerated solvent extraction – ASE), maceration, and sonication. Samples of mate tea leaves were collected from an experiment conducted under agronomic control at Indústria e Comércio de Erva‐Mate Bar?o LTDA, Brazil. Six solvents with increasing polarities (n‐hexane, toluene, dichloromethane, ethyl acetate, acetone, and methanol) were used in this investigation. Chemical analysis of the extracts was performed by GC coupled with a mass spectrometer detector. The identification and quantification were accomplished by coinjections of certified standards. The results showed that no significant differences in the qualities of the extracts were noticed regarding the extraction methods. On the other hand, the PLE technique was found to be more effective for the extractions of caffeine, phytol, palmitic, and stearic acid. The use of PLE led to a significant decrease in the total extraction time, amount of solvent consumption, and manipulation of samples compared to maceration and ultrasound‐assisted extraction methods.     

Selective pressurized liquid extraction of polybrominated diphenyl ethers in fish

A fast and simple method for the analysis of polybrominated diphenyl ethers (PBDEs) in fish samples was developed using a one-step extraction and clean-up by means of pressurized liquid extraction (PLE) combined with gas chromatography-ion trap tandem mass spectrometry (GC-ITMS-MS). The selective PLE method provided to obtain ready-to-analyse extracts without any additional clean-up step, using a sorbent as fat retainer inside the PLE cell. Several PLE operating conditions, such as solvent type, extraction temperature and time, number of cycles and type of fat retainer, were studied. Using Florisil as fat retainer, maximum recoveries of PBDEs (83-108%) with minimum presence of matrix-interfering compounds were obtained using a mixture of n-hexane:dichloromethane 90:10 (v/v) as solvent, an extraction temperature of 100 °C and a static extraction time of 5 min in combination with three static cycles. Quality parameters of the method were established using standards and fish samples. Limits of detection and quantification ranged from 10 to 34 pg g⁻¹ wet weight and between 34 and 68 pg g⁻¹ wet weight, respectively. In addition, good linearity (between 1 and 500 ng ml⁻¹) and high precision (RSD % < 15%) were achieved. The method was validated using the standard reference material SRM-1945 (whale blubber) and was then applied to the analysis of PBDEs in fish samples.