An iron(III) ion-selective sensor based on a μ-bis(tridentate) ligand

A μ-bis(tridentate) ligand named 2-phenyl-1,3-bis[3′-aza-4′-(2′-hydroxyphenyl)-prop-4-en-1′-yl]-1,3-imidazolidine (I) has been synthesized and scrutinized to develop iron(III)-selective sensors. The addition of sodium tetraphenyl borate and various plasticizers, viz., chloronaphthalene, dioctylphthalate, o-nitrophenyl octyl ether and dibutylphthalate has been used to substantially improve the performance of the sensors. The membranes of various compositions of the ligand were investigated and it was found that the best performance was obtained for the membrane of composition (I) (10 mg):PVC (150 mg):chloronaphthalene (200 mg):sodium tetraphenyl borate (9 mg). The sensor showed a linear potential response to iron(III) over wide concentration range 6.3 × 10⁻⁶ to 1.0 × 10⁻¹ M (detection limit 5.0 × 10⁻⁶ M) with Nernstian slope (20.0 mV/decade of activity) between pH 3.5 and 5.5 with a quick response time of 15 s. The potentiometric selectivity coefficient values as determined by match potential method (MPM) indicate excellent selectivity for Fe³⁺ ions over interfering cations. The sensor exhibits adequate life of 2 months with good reproducibility. The sensor could be used in direct potentiometry.     

Another example of carborane based trianionic ligand: Syntheses and catalytic activities of cyclohexylamino tailed ortho-carboranyl zirconium and titanium dicarbollides

In situ reaction of Li[closo-1-Ph-1,2-C₂B₁₀H₁₀] with 7-azabicyclo [4.1.0] heptane results in the formation of the disubstituted carborane, closo-1-Ph-2-(2′-aminocyclohexyl)-1,2-C₂B₁₀H₁₀ (1), in 63% yield. Decapitation of (1) with potassium hydroxide in refluxing ethanol produces the cage-opened nido-carborane, K[nido-7-Ph-8-(2′-aminocyclohexyl)-7,8-C₂B₉H₁₀]⁻ (2), in 80% yield. Deprotonation of the above monoanion with two equivalents of n-butyllithium followed by reaction with anhydrous MCl₄ · 2THF (M = Zr, Ti) provides d⁰-half-sandwich metallocarboranes, closo-1-M(Cl)-2-Ph-3-(2′-σ-(H)N-cyclohexyl)-2,3-η⁵-C₂B₉H₉ (3 M = Zr; 4 M = Ti) in 53% and 42% yields, respectively. The reaction of Li[closo-1,2-C₂B₁₀H₁₁] with 7-azabicyclo [4.1.0] heptane in THF affords closo-1-(2′-aminocyclohexyl)-1,2-C₂B₁₀H₁₀ (5) in 59% yield. Immobilization of the carboranyl amino ligand (1) to an organic support, Merrifield’s peptide resin (1%), has been achieved by the reaction of the sodium salt of (5) with polystyryl chloride in THF to produce closo-1-(2′-aminocyclohexyl)-2-polystyryl-1,2-C₂B₁₀H₁₀ (6) in 87% yield. Further reaction of the dianion derived from (6) with anhydrous ZrCl₄ · 2THF led to the formation of the organic polystyryl supported d⁰-half-sandwich metallocarborane, closo-1-Zr(Cl)-2-(2′-σ-(H)N-cyclohexyl)-3-polystyryl-2,3-η⁵-C₂B₉H₉ (7), in 38% yield. These new compounds have been characterized by elemental analyses, NMR, and IR spectra. Polymerizations of both ethylene and vinyl chloride with (3) and (7) have been performed in toluene using MMAO-7 (13% ISOPAR-E) as the co-catalyst. Molecular weights up to 32.8 × 10³ (M_w/M_n = 1.8) and 9.5 × 10³ (M_w/M_n = 2.1) were obtained for PE and PVC, respectively.     

X-ray crystal structure analysis and atomic charges of color former and developer: 2. Color formers

The crystal and molecular structures of 2′-amino-6′-dibutylamino-3′-methylspiro[isobenzofuran-1(3H), 9′[9H]xanthen]-3-one (1), 2′-amino-6′-(N-cyclohexyl-N-methylamino)-3′-methylspiro[isobenzofuran-1(3H), 9′[9H]xanthen]-3-one (2) and 2′-(2-chlorophenyl)amino-6′-dibutylaminospiro[isobenzofuran-1(3H), 9′[9H]xanthen-3-one (3) have been determined by single-crystal X-ray diffraction analysis. Atom-atom non-bonded potential energy and semiempirical quantum chemical calculations have been performed. The xanthene rings of 1 to 3 are slightly bent and the phthalide rings are planar. The phthalide ring moieties are almost perpendicular (88.9(1)–93.5(5)°) to the xanthene rings. The bond lengths C(6)---O(2) are apparently extended from the normal C(sp³---O (lactone) length. The temperature factors for one butyl group C(32)---C(35)) of 1 increase gradually toward the terminal carbon. The temperature factors for C(30)---C(33) of 2 indicate large vibrations and these are reflected in short bond lengths. Two butyl groups of 3 are disordered and these C---C bond lengths are short and long alternately. Atomic net charges around spirocarbon C(6) and toward N(1) to C(6) indicate the weak alternative system in the colorless form. As the xanthene ring has a planar geometry, the π electron density migration will easily occur from the auxochromes attached to the phthalide ring to the xanthene ring.     

X-ray crystal structure analysis and atomic charges of color former and developer: 2. Color formers

The crystal and molecular structures of 2′-amino-6′-dibutylamino-3′-methylspiro[isobenzofuran-1(3H), 9′[9H]xanthen]-3-one (1), 2′-amino-6′-(N-cyclohexyl-N-methylamino)-3′-methylspiro[isobenzofuran-1(3H), 9′[9H]xanthen]-3-one (2) and 2′-(2-chlorophenyl)amino-6′-dibutylaminospiro[isobenzofuran-1(3H), 9′[9H]xanthen-3-one (3) have been determined by single-crystal X-ray diffraction analysis. Atom-atom non-bonded potential energy and semiempirical quantum chemical calculations have been performed. The xanthene rings of 1 to 3 are slightly bent and the phthalide rings are planar. The phthalide ring moieties are almost perpendicular (88.9(1)−93.5(5)°) to the xanthene rings. The bond lengths C(6)---O(2) are apparently extended from the normal C(sp³)---O (lactone) length. The temperature factors for one butyl group C(32)---C(35)) of 1 increase gradually toward the terminal carbon. The temperature factors for C(30)---C(33) of 2 indicate large vibrations and these are reflected in short bond lengths. Two butyl groups of 3 are disordered and these C---C bond lengths are short and long alternately. Atomic net charges around spirocarbon C(6) and toward N(1) to C(6) indicate the weak alternative system in the colorless form. As the xanthene ring has a planar geometry, the π electron density migration will easily occur from the auxochromes attached to the phthalide ring to the xanthene ring.     

Novel cyclopentadienyl silanes and disilanes: synthesis, structure and gas-phase pyrolysis

The new chloro(cyclopentadienyl)silanes Cp′SiH_yCl_3−y (Cp′=Me₄EtC₅, y=1: 1; Cp′=Me₄C₅H, y=1: 2; y=0: 3; Cp′=Me₃C₅H₂, y=1: 4 and pentachloro(cyclopentadienyl)disilanes Cp′Si₂Cl₅ (Cp′=Me₅C₅ 5, Me₄EtC₅ 6, Me₄C₅H 7, Me₃C₅H₂ 8, Me₃SiC₅H₄ 9) are synthesized in good yields via metathesis reactions. Treatment of 1–9 with LiAlH₄ leads under Cl–H exchange to the hydridosilyl compounds Cp′SiH₃ (Cp′=Me₄EtC₅ 10, Me₄C₅H 11, Me₃C₅H₂ 12) and to the hydridodisilanyl compounds Cp′Si₂H₅ (Cp′=Me₅C₅ 13, Me₄EtC₅ 14, Me₄C₅H 15, Me₃C₅H₂ 16, Me₃SiC₅H₄ 17). Complexes 1–17 are characterized by ¹H, ¹³C, and ²⁹Si-NMR spectroscopy, IR spectroscopy, mass spectrometry and CH-analysis. The structures of 6, 7 and 9 are determined by single-crystal X-ray diffraction analysis. Pyrolysis studies of the cyclopentadienylsilanes 10–12 and disilanes 13–17 show their suitability as precursors in the MOCVD process.     

H, C, N NMR, ESI mass spectral and single crystal X-ray structural characterization of three spiro[pyrrolidine-2,3′-oxindoles]

Three spiro[pyrrolidine-2,3′-oxindoles], 1,1′,2,2′,5′,6′,7′,7′a-octahydro-2-oxo-1′-phenyl-spiro[3H-indole-3,3′-[3H]-pyrrolizine]-2′-carboxylic acid methyl ester (1), 1,1′,2,2′,5′,6′,7′,7′a-octahydro-2-oxo-1′-nitro-2′-phenyl-spiro[3H-indole-3, 3′-[3H]-pyrrolizine] (2) and 1,1′,2,2′,5′,6′,7′,7′a-octahydro-2-oxo-1′-nitro-2′-(4″-chlorophenyl)-spiro[3H-indole-3,3′-[3H]-pyrrolizine] (3) have been synthesized and their ¹H, ¹³C and ¹⁵N spectra assigned. The chemical shift assignments are based on Pulsed Field Gradient (PFG) Double Quantum Filter (DQF) ¹H, ¹H correlation spectroscopy (COSY), PFG ¹H, ¹³C Heteronuclear Multiple Quantum Coherence (HMQC) and PFG ¹H,X (X = ¹³C and ¹⁵N) Heteronuclear Multiple Bond Correlation (HMBC) experiments. The single crystal X-ray structures of 1–3 have been determined. Compounds 1 and 2 crystallized in monoclinic space group C2/c and compound 3 in monoclinic space group P2₁/c, respectively. Also the ESI-TOF MS data of 1–3 are given.     

Liquid chromatographic–electrospray mass spectrometric study of the phthalides of Angelica sinensis and chemical changes of Z-ligustilide

High-performance liquid chromatography–electrospray ionization–mass spectrometry has been applied to analyze the chemical constituents of Danggui (the rhizome of Angelica sinensis) and to study chemical changes of Z-ligustilide. Twelve phthalides were unambiguously identified as senkyunolide I (3), senkyunolide H (4), sedanenolide (8), butylphthalide (9), E-ligustilide (13), Z-ligustilide (14), Z-butylidenephthalide (15), Z,Z′-6.8′,7.3′-diligustilide (16), angelicide (17), levistolide A (18), Z-ligustilide dimer E-232 (19) and Z,Z′-3.3′,8.8′-diligustilide (20) in Danggui extract. The existence of 12 other phthalides (2, 5–7, 11, 12, 22–27), ferulic acid (1) and coniferyl ferulate (10) in Danggui extract has also been demonstrated. Phthalides 3, 4, 16–18 and 20 were determined to be the products from chemical change of Z-ligustilide. This is the first report of the existence of 16 compounds (2–8, 10–12, 20, 22–25 and 27) in Danggui extract.     

Azacrown ethers containing oximic and Schiff base sidearms - potential heteronuclear metal ion receptors

A simple synthetic pathway for the preparation of oxime- and Schiff base-containing aza- and diazacrown ethers is reported. N-Methoxymethyl-substituted aza-15-crown-5 and aza-18-crown-6 as well as N,N′-bis(methoxymethyl)-substituted diaza-18-crown-6 were treated with 5-bromosalicylaldehyde to produce the N-(2′-hydroxy-3′-carbonyl-5′-bromobenzyl)-substituted aza-15-crown-5 (8), aza-18-crown-6 (9) and N,N′-bis(2′-hydroxy-3′-carbonyl-5′-bromobenzyl)-substituted diaza-18-crown-6 (10) compounds. Compounds 8 and 10 were treated with hydroxylamine to give oxime-substituted ligands 12 and 13. A series of bis-Schiff base-containing diaza-18-crown-6 ligands were prepared by reacting 10 with 2-hydroxyaniline (to form 14), 5-nitro-2-hydroxyaniline (15), 2-aminopyridine (16), 2-hydrazinopyridine (17) and N-aminomorpholine (18). Compounds 12–18 are potential complexing agents for simultaneous binding of soft transition and hard alkali or alkaline earth metal ions in one molecule. These new oxime- and Schiff base-containing ligands interacted strongly with Na⁺ and K⁺ in methanol. The interaction of the aromatic portions of 9, 10, and 12–15 with transition metal ions was shown by the UV spectra of the metal ion complexes in 50% aqueous DMF. The X-ray structure of 10 is reported.     

Chains, ladders and sheets of d metal–organic polymers generated from the flexible bipyridyl ligands

By use of the three-layer diffusion method, reactions of flexible bipyridyl ligands (4,4′-bpp or 3,3′-bpp) with M(II) salts (M = Zn, Cd) and multi-carboxylate ligands resulted in the formation of four interesting d¹⁰ metal–organic coordination polymers: [Zn(μ-4,4′-bpp)Br₂]_n (1), [Zn(μ-4,4′-bpp)(1,2-bdc)]_n · nH₂O (2), [Zn(μ-3,3′-bpp)(1,3-bdc)]_n · nCH₃OH · 2nH₂O (3) and [Cd(μ-3,3′-bpp)(C₄H₂O₄)]_n · 3nH₂O (4) (4,4′-bpp = 2,2′-bis(4-pyridylmethyleneoxy)-1,1′-biphenylene; 3,3′-bpp = 2,2 ′-bis(3-pyridylmethyleneoxy)-1,1′-biphenylene; bdc=benzenedicarboxylate, C₄H₄O₄ = fumaric acid). Complex 1 has a 2D sheet structure consisting of two unusual zigzag Zn(II) chains which are nearly perpendicular to each other. Complex 2 is comprised of two-leg ladders, in which [Zn(4,4′-bpp)] chains serve as the side rails and 1,2-bdc ligands serve as the cross rungs. In complex 3, every two 1,3-bdc ligands connect the neighbouring Zn(II)-3,3′-bpp dimetallic rings in η¹ coordination modes into an interesting chain structure. Complex 4 consists of an anionic macrocycle-containing cadmium dicarboxylate sheets that are separated by 3,3′-bpp. These d¹⁰ metal complexes exhibit high thermal stabilities and strong luminescence efficiencies.     

Reactions of Ru(CCPh)(L2)Cp* (L2=dppm, dppe) with tetracyanoethene: cycloaddition, formation of monodentate dppm and dppmO complexes and migration of CN to ruthenium

Reactions of FcCCH (a), HCCCCFc (b) and FcCCCCFc (c) with Ru₃(CO)₁₀(NCMe)₂ (all) and Ru₃(μ-dppm)(CO)₁₀ (b and c only) are described. Among the products, the complexes Ru₃(μ₃-RC₂R′)(μ-CO)(CO)₉ (R=H, R′=Fc 1, CCFc 2; R=R′=Fc 5), Ru₃(μ-H)(μ₃-C₂CCFc)(μ-dppm)(CO)₇ 3, Ru₃(μ₃-FcC₂CCFc)(μ-dppm)(μ-CO)(CO)₇ 6 and Ru₃{μ₃-C₄Fc₂(CCFc)₂}(μ-dppm)(μ-CO)(CO)₅ 7 were characterised, including single-crystal structure determinations for 1, 3, 5 and 7; that of 7 did not differ significantly from an earlier study of a mixed CH₂Cl₂–C₆H₆ solvate.     

Synthesis, characterization and catalytic activity in Heck-type reactions of orthometallated Pd and Pt complexes derived from (1R,2R)-1,2-diaminocyclohexane

The chiral bis-imine (1R,2R)-C₆H₁₀-[E---N=CH---C₆H₃---3,4-(OMe)₂]₂ 1 (LH) reacts with [Pd(OAc)₂] (1:1 molar ratio; OAc=acetate) giving the orthometallated [Pd(OAc)(C₆H₂---4,5-(OMe)₂---2-CH=N-(1R,2R)-C₆H₁₀---N=CH---C₆H₃-3′,4′-(OMe)₂-κ-C,N,N)] 2 (abbreviated as [Pd(OAc)(L-κ-C,N,N)]), through C---H bond activation on only one of the aryl rings and N,N-coordination of the two iminic N atoms. 2 reacts with an excess of LiCl to give [Pd(Cl)(L-κ-C,N,N)] 3. The reaction of 3 with AgClO₄ and neutral or anionic ligands L′ (1:1:1 molar ratio) affords [Pd(L-κ-C,N,N)(L′)](ClO₄) (L′=PPh₃ 4a, NCMe 5, pyridine 6, p-nitroaniline 7) or [Pd(I)(L-κ-C,N,N)] 8. Complex 4a reacts with wet CDCl₃ giving [Pd(C₆H₂---4,5-(OMe)₂---2-CH=N-(1R,2R)---C₆H₁₀---NH₂-κ-C,N,N)(PPh₃)](ClO₄) 4b as a result of the hydrolysis of the C=N bond not involved in the orthometallated ring. The molecular structure of 4b·CH₂Cl₂ has been determined by X-ray diffraction methods. Cleavage of the Pd---N bond trans to the C_aryl atom can be accomplished by coordination of strongly chelating ligands, such as acetylacetonate (acac) or bis(diphenylphosphino)ethane (dppe), forming [Pd(acac-O,O′)(L-κ-C,N)] 9 and [Pd(L-κ-C,N)(dppe-P,P′)](ClO₄) 12, while classical N,N′-chelating ligands such as 1,10-phenantroline (phen) or 2,2′-bipyridyl (bipy) behave as monodentate N-donor ligands yielding [Pd(L-κ-C,N,N)(κ¹-N-phen)](ClO₄) 10 and [Pd(L-κ-C,N,N)(κ¹-N-bipy)](ClO₄) 11. Treatment of 1 with PtCl₂(DMSO)₂ (1:1 molar ratio) in refluxing 2-methoxyethanol gives Cl₂Pt[(NH₂)₂C₆H₁₀---N,N′] 13a and [Pt(Cl)(C₆H₂---4,5-(OMe)₂---2-CH=N-(1R,2R)---C₆H₁₀---NH₂-κ-C,N,N)] 13b, while [Pt(Cl)(L-κ-C,N,N)] 14 can be obtained by reaction of [Pt(μ-Cl)(η³-2-Me---C₃H₄)]₂ with 1 in refluxing CHCl₃. Complexes 2 and 3 catalyzed the arylation of methyl acrylate giving good yields of the corresponding methyl cinnamates and TON up to 847 000. Complex 3 also catalyzes the hydroarylation of 2-norbornene, but with lower yields and without enantioselectivity.     

Investigation on lanthanide binuclear complexes of 1,5-bis-(1′-phenyl-3′-methyl-5′-pyrazolone-4′)-1,5-pentanedione and 2,2′-bipyridine

The coordination of 1,5-bis-(1′-phenyl-3′-methyl-5′-pyrazolone-4′)-1,5-pentanedione (BPMPPD) and 2,2′-bipyridine (bipy) with lanthanide ions in water-alcohol solution has been studied. Binuclear complexes of the types : Ln₂(BPMPPD)₃(bipy)₂·nH₂O (n = 2 for Y, n = 4 for Eu, Gd, Dy, Ho, Er, Tm and Yb); Ln₂(BPMPPD)₃bipy·nH₂O (n = 10 for La, n = 3 for Pr, Nd, Sm and Tb) were formed. The compounds were characterized by elemental analysis, molar conductance, IR, UV, ¹H NMR spectroscopy, thermogravimetric analysis and fluorescence spectra.     

Raney nickel reductions—VIII A synthesis of 1:2-benzanthracene and its 3′-methyl and 4-methyl derivatives

1:2-Benzanthracene and the 3′-methyl derivative have been prepared by Raney nickel reduction of the sulphuric esters of the leuco derivatives of 1:2-benzanthraquinone and 4′-chloro-3′-methyl-1:2-benzanthraquinone, followed by dehydrogenation. 3-Hydroxy-1:2-benzanthraquinone was methylated in the 4-position by formaldehyde, sodium hydrosulphite and sodium hydroxide solution (the Marschalk reaction). Simultaneous reduction of the nuclear hydroxyl and quinone groups was effected by Raney nickel reduction of the trisulphuric ester of 3:9:10-trihydroxy-4-methyl-1:2-benzanthracene, and the resultant hexahydro-4-methyl-1:2-benzanthracene was dehydrogenated to 4-methyl-1:2-benzanthracene. The preparation of 3:4:9:10-dibenzopyrene from Mayvat brilliant red AF by Raney nickel reduction of the sulphuric ester of the leuco derivative and subsequent dehydrogenation is described.     

Furano compounds—IX

Starting with the appropriate 3-hydroxybenzoxanthones and the following the sequence of reactions allylation, Claisen migration, acetylation, bromine addition and dehydrobromination, 7:8-benzo- and 5:6-benzo-3:4, 2′:3′-furanoxanthones have been synthesized.     

Adsorptive stripping voltammetric determination of antimony

A new method is described for the determination of antimony based on the cathodic adsorptive stripping of Sb(III) complexed with 2′,3,4′,5,7-pentahydroxyflavone(morin) at a static mercury drop electrode (SMDE). The reduction current of the adsorbed antimony complex was measured by 1.5th-order derivative linear-sweep adsorption voltammetry. The peak potential is at −0.51 V (vs. SCE). The effects of various parameters on the response are discussed. The optimized analytical conditions were found to be: supporting electrolyte, chloroacetic acid (0.04 mol/l, pH 2.3); concentration of morin, 5×10⁻⁶ mol/l; accumulation potential, −0.25 V (vs. SCE); scan rate, 100 mV/s. The limit of detection and the linear range were 7×10⁻¹⁰ mol/l and 1.0×10⁻⁹3.0×10⁻⁷ mol/l Sb(III) for a 2-min accumulation time, respectively. This method has been applied to the determination of Sb(III) in steel and brass samples and satisfactory results were obtained. The adsorptive voltammetric characteristics and composition of the Sb(III)–morin complex were studied.     

Synthetic analogues of wedelolactone

The syntheses of 7′-methoxy- and 5′,7′,6-trimethoxy-coumarino(3′,4′:3,2)coumarones (IIa and IIb) are described.     

Annellation effects in the perylene and coronene series

Naphtho(2′:3′, 2:3)perylene (VIII), dinaphtho(2′:3′, 2:3); (2″:3″, 8:9)perylene (VII), anthraceno(1′:4′, 1:12)perylene(IV), 1:12-benzonaphtho(2″:3″, 2:3)perylene(II), 1:12-benzonaphtho (2″:3″, 4:5)perylene (III) and 1:12-benzodinaphtho(2″:3″, 2:3); (2″“:3″”,8:9)perylene (XV) were synthesized. There are two different annellation effects in passing from 1:12-benzoperylene (I) to II or III resp., the one in naphthocoronene (V) lies in between these two effects. The annellation effect in the perylene series cannot be related to the molecular axes but is easily explained by the strict application of Robinsons aromatic sextet.     

Rhenium(I) methoxo carbonyl complexes containing tetraphosphine or triphosphine ligands; facile separation and X-ray crystallographic studies of d/l- and meso-[{Re2(μ-OMe)2(CO)6}2(μ,μ′-1,1,4,7,10,10-hexaphenyl-1,4,7,10-tetra-phosphadecane)]

Reaction of the activated mixture of Re₂(CO)_10, Me₃NO and MeOH with a 1:1 mixture of rac (d/l)- and meso-1,1,4,7,10,10-hexaphenyl-1,4,7,10-tetraphosphadecane (hptpd) yields a mixture of (d/l)- and meso-[{Re₂(μ-OMe)₂(CO)₆}₂(μ,μ′-hptpd)] 1. The diastereomers can be easily separated by selective dissolution of d/l-1 in benzene, and give clearly distinguishable ¹H- and ³¹P-NMR spectra. The fluxional behavior of d/l-1 in solution has been studied by variable-temperature ¹H- and ³¹P-{¹H}-NMR spectroscopy. The crystal structures of both d/l- and meso-1 have been determined. Both molecules consist of two {Re₂(μ-OMe)₂(CO)₆} moieties which are bridged by the two P---CH₂---CH₂---P moieties of the hptpd ligand. Whilst the molecules of meso-1 possess crystallographic i-symmetry, those of d/l-1 do not have any crystallographic symmetry. These diastereomers therefore give clearly distinguishable Raman spectra in the solid state. Reaction of tris[2-(diphenylphosphino)ethyl]phosphine (tdppep) with the activated mixture affords the complex [{Re₂(μ-OMe)₂(CO)₆}(μ,η²-tdppep)] 2, and the analogous reaction involving bis[2-diphenylphospinoethyl)phenylphosphine (triphos) gives [{Re₂(μ-OMe)₂(CO)₆}(μ,μ′,η³-triphos){Re₂(CO)₉}] 3 and [{Re₂(μ-OMe)₂(CO)₆}(μ,η²-triphos)] 4.     

The use of thermotropic liquid crystals in organometallic chemistry. Synthesis of new mercury, silver and gold complexes with 4,4′-disubstituted azob

Liquid crystalline 4-XC₆H₄N=NC₆H₄X-4′ [X = C₄H₉ (1a), C_1OH₂₁ (1b), OC₄H₉ (1c), OC₈H₁₇(1d)] can be easily prepared in high yields from the corresponding anilines. In order to study the influence of metals on the thermal properties of these materials, we have obtained adducts [AuCl ₃(4-C₄H₉OC₆H₄N=NC₆H₄OC₄H₉-4′)] (2) and [Ag(OC1O₃)L₂] [L = 4-XC₆H₄N=NC₆H₄X-4′; X = OC₄H, (3a), OC₈H₁₇ (3b)]. The silver adducts show themotropic behaviour. Mercuriation of dialkylazobenzenes 1a-b takes place with [Hg(OAc)₂] and LiCl to give [Hg(R)Cl] [R = C₆H₃(N=NC₆H₄X-4′)-2, X-5; X = C₄H₉ (bpap) (4a), C₁₀H₂₁ (dpap) (4b)] while dialkoxyazobenzenes 1c–d require [Hg (OOCCF₃)₂] to obtain [Hg(R)Cl] [R = C₆H₃(N---NC₆H₄X-4′)-2, X-5; X = OC₄H₉ (bxpap) (4c), OC ₈H₁₇ (4d)]. 4a-c react with NaI to give [HgR₂] [R= bpap (5a), dpap (5b), bxpap (5c), oxpap (5d)l. Both chloroaryl-, 4a and 4c, and diaryl-mercurials, 5a and 5c, act readily as transmetailating agents towards [Me₄N] [AuCl₄] in the presence of [Me₄N]Cl to give [Au(η²-R)Cl₂] [R = bpap (6a), bxpap (6b)]. After reaction of [AuCl ₃(tht)] (tht = tetrahydrothiophene) with [Me₄N]Cl and 4b (1:2:1), [Me₄N][Au(dpap)Cl₃] (7) can be isolated. C---H activati bxpap (8b)]. None of the complexes 4–8 shows mesomorphic behaviour.     

Structures of 3,3′-dicarbometoxy-2,2′-bipyridine complexes with silver(I) and copper(II) cations

The structures of 3,3′-dicarbometoxy-2,2′-bipyridine (dcmbpy) complexes with copper(II) and silver(I) cations have been determined using single crystal X-ray-diffraction. The crystals of Cu(dcmbpy)Cl₂ are monoclinic, C2/c, a = 16.966(3), b = 18.373(3), c = 13.154(2) Å, β = 126.543(3)°. The crystals of Ag(dcmbpy)NO₃ · H₂O are also monoclinic, C2/c, a = 16.7547(13), b = 11.0922(9), c = 18.7789(18) Å, β = 100.228(7)°. The results have been compared with the literature data on the complexes of dcmbpy and its precursors: 2,2′-bipyridine (bpy) and 3,3′-dicarboxy-2,2′-bipyridine (dcbpy). Two types of complexes of 3,3′-carboxy derivatives of bpy are distinguished: (1) with metal atom bonded to two N atoms of the same molecule and (2) with metal atom bonded to two N atoms of two different molecules. The Cu(dcmbpy)Cl₂ complex belongs to the first type, whereas Ag(dcmbpy)NO₃ · H₂O belongs to the second type.