固相微萃取/高效液相色谱法测定水中的微囊藻毒素

采用CWX/DVB萃取头,应用固相微萃取与高效液相色谱联用技术(SPME/HPLC)分析了水溶液中的痕量微囊藻毒素。对SPME的萃取条件进行了优化,并对实际水样进行了分析。该方法测定MC-LR(LR型微囊藻毒素)的线性范围为1.00~200μg/L,相关系数为0.999 5,检出限为0.45μg/L(3σ,n=11),相对标准偏差(RSD)为2.4%,回收率为90%~99%。该方法测定MC-RR(RR型微囊藻毒素)的线性范围为1.00~100μg/L,相关系数为0.998 8,检出限为0.15μg/L(3σ,n=11),RSD为2.4%,回收率为89%~100%。     

Determination of Non-Steroidal Anti-Inflammatory Drugs in Natural Waters Using Off-Line and On-Line SPE Followed by LC Coupled with DAD-MS

Two different procedures for simultaneous determination of six NSAIDs (diflunisal, diclofenac, fenoprofen, ibuprofen, naproxen and tolmetin) in environmental waters are described. Final analysis of target compounds is performed by reversed-phase liquid chromatography – diode array detection and mass spectrometry (HPLC-DAD and LC-MS), whereas sample preparation is based on solid-phase extraction (SPE). A variety of sorbents and their respective advantages and disadvantages are discussed. For the off-line SPE of NSAIDs from water samples, a LiChrolut RP-18 was selected out of all investigated sorbents. In case of on-line coupling of SPE with chromatographic system LiChrosphere RP-18 was selected as the best one in terms of recovery of NSAIDs evaluated, RSD and availability. The applicability of the method was also evaluated. Method detection limits were in the range of 0.7−94 ng L⁻¹. Recoveries ranged from 96 to 109% and relative standard deviations were lower than 5%. The procedures were shown to be linear over a wide range of concentration, exhibited satisfactory repeatability and accuracy, and reached limits of detection in the low ng L⁻¹ range. No breakthrough volume was observed neither for off-line SPE (in the studied range of 100, 200, 300, 500, 700, 1000 and 2000 mL of tap water sample) nor for on-line SPE (in the wide range of 10 mL, 20 mL, 30 mL, 50 mL, 70 mL, 100 mL and 200 mL of tap water sample).     

Simultaneous Determination of Phytohormones in Plant Extracts using SPME and HPLC

Solid-phase microextraction followed by HPLC was used for the determination of indole-3-acetic acid (IAA), abscisic acid (ABA), indole-3-butyric acid (IBA) and 1-naphthylacetic acid (NAA) in plant samples. Parameters influencing performance, including pH, salinity, extraction time, fiber coating and temperature, were optimized. A Carbowax-coated fiber was chosen for determination due to much higher extraction efficiency compared to polyacrylate fibers. The dynamic ranges spanned over three orders of magnitude. The LOD/(LOQ) values of the target compounds in pure water were 0.149(0.497), 0.442(1.472), 0.121(0.403), 0.058(0.193) μg L⁻¹ for IAA, ABA, IBA and NAA respectively. The method was successfully applied to the analysis of xylem fluid from Musa basjoo stem obtaining recoveries of 98.85% (IAA), 94% (IBA) and 94.30% (NAA). The method was also successfully applied to the analysis of these four target compounds in the hyperaccumulating plant, Viola baoshanensis. The results matched quite well with ones obtained by solid phase extraction followed by HPLC. The method developed was superior when applied to liquid samples because matrix effects could be eliminated.     

Simultaneous Determination of Various Classes of Pesticides Using Micellar Electrokinetic Capillary Chromatographyin Combination with Solid-Phase Extraction

The potential of micellar electrokinetic capillary chromatography (MEKC) with UV-detection for the simultaneous determination of various selected pesticides in water samples was investigated. The developed method using solid-phase extraction showed high efficiency and good resolution with detection limits in the 0.2 to 0.5 ppm range. Comparison of several SPE cartridges demonstrates their suitability for the extraction of pesticides with different hydrophobicity achieving 5000-fold enrichment. The described method involving SPE procedure and MEKC separation enables the successful determination of a wide spectrum of pesticides in water in the range of maximum residue limits (MRLs).     

Simultaneous LC Determination of Ginsenosides Using a Modified Extraction Procedure and an Improved Step Gradient Program

A novel, accurate and precise high performance liquid chromatographic method has been developed for simultaneous determination of seven important ginsenosides (Rg1, Re, Rf, Rb1, Rc, Rb2 and Rd) in ginseng products. The separation was performed on a Shim-pack VP-ODS column (5 μm, 150 ×2 mm i.d) with ultraviolet detection at 200 nm by using the improved step gradient elution program. The LODs (S/N = 3) were in the range 0.29 to 1.33 ng μL⁻¹. All calibration curves showed a good linearity (R² > 0.998) over the ranges tested. The recoveries obtained from spiked sample were between 95.1% and 98.7%. The proposed method was successfully applied to several ginseng pharmaceutical samples. For the sample preparation, a modified extraction method was made to improve the extraction efficiency by evaluation of five solvent systems. The results demonstrated that the extraction with methanol-water (80:20, v/v) is suitable method preferably for the extraction of the ginsenosides. On leave from Department of Pharmacy and Applied Chemistry, Jilin Institute of Chemical Technology, Jilin 132022, P. R. China     

分散液液微萃取-气相色谱法测定水样中甲拌磷农药

建立了基于分散液液微萃取(DLLME)的新型样品前处理方法,并采用气相色谱/氢火焰离子化检测器对水样中痕量的甲拌磷农药进行了测定。考察了影响分散液液微萃取的因素包括萃取溶剂、分散剂、样品体积、萃取温度和离心速度等。在最佳实验条件下,对甲拌磷的富集倍数达到300倍;检出限为0.001μL/L;方法的线性范围为0.01~10μL/L,R2为0.9986;相对标准偏差为6.65%;回收率为104%。将分散液液微萃取法与单滴液相微萃取和离子液体-液相微萃取方法进行了对比,结果表明,分散液液微萃取技术具有操作简单、快捷(前处理时间小于5 min)、富集效果好、回收率高等优点。同时预言,将离子液体与分散液液微萃取结合,将会产生更加满意的结果。     

超声辅助分散液液微萃取-高效液相色谱法快速测定水样中的6种农药

为实现小体积环境水祥中不同农药的准确、快速、高灵敏测定,通过研究萃取剂、分散剂的种类、体积、盐浓度及超声时间对萃取效率的影响,结合分散液液微萃取与超声萃取技术,并与高效液相色谱联用,建立了快速测定环境水样中的吡虫啉、水胺硫磷、辛硫磷、毒死蜱、哒螨灵和阿维菌素6种农药的方法.在优化的萃取条件下,检测6种农药的线性范围为10～ 600 μg/L,检出限(S/N=3)为0.8～3.1 μg/L,相对标准偏差为4.7％～11.3％,富集倍数可达到58～187倍.本方法具有良好的线性、精密度和回收率,并具有较好的实用性.     

Simultaneous Determination of Cyanazine, Chlorotoluron and Chlorbenzuron in Environmental Water Samples with SPE Multiwalled Carbon Nanotubes and LC

In this paper, a new method based on solid-phase extraction with multiwalled carbon nanotubes as the packed materials for sensitive determination of cyanazine, chlorotoluron and chlorbenzuron in environmental water samples was demonstrated. Related parameters that may influence the enrichment efficiency of multiwalled carbon nanotubes such as the kind and volume of elute, sample flow rate, sample pH, and volume of the water samples were investigated. Under the optimum conditions, the detection limits of cyanazine, chlorbenzuron and chlorotoluron were 0.015, 0.012, 0.034 ng mL⁻¹, respectively. The experimental results indicated a good linearity (R ² > 0.9947) over the concentration range of 0.4–40 ng mL⁻¹ for cyanazine and chlorotoluron, and 0.8–80 ng mL⁻¹ for chlorbenzuron. The relative standard deviations of the three analytes were 3.54, 1.55 and 1.38%, respectively. The established method also was applied to the analysis of the real-world water samples and excellent achievements were obtained with average spiked recoveries from 87.8 to 110.1%. All the results indicated that this procedure could allow the simultaneous determination of these three compounds in environmental water samples at trace levels.     

自制的SPME装置与GC-MS联用测定室内空气中的挥发性有机化合物

用直接进样、固相萃取进样和自制的固相微萃取（SPME）装置进样与气相色谱（GC）及GC—MS联用检测了室内空气中的挥发性有机污染物，对影响SPME操作条件进行了优化。使用的方法在所测范围内具有良好的线性（相关系数为0．968～0．991），检出限达0．3—2、3μg/L，相对标准偏差均小于7％，回收牢为95％～111％。结果表明：自制的SPME装置操作简单、快速、安全，准确度、灵敏度优于其它两种方法。     

Comparison of on-line SPE-HPLC and SPME-GC for the analysis of microcontaminants in water

Summary Solid-phase preconcentration coupled on-line with liquid chromatography, and solid-phase microextraction coupled with gas chromatography have been applied to the determination of trace-level concentrations of benzene and sulfur compounds (tetrahydrothiophene (THT),t-butyl mercaptan (TBM), andn-butyl mercaptan (nBM)) in aqueous media. The first technique uses a microcolumn packed with a styrene-divinylbenzene copolymer. Retention values for THT, TBM, and benzene on this sorbent, expressed as the capacity factors, are 1100, 1600, and 4000, respectively. It is, therefore, possible to preconcentrate them efficiently and this method enables minimum concentrations of 0.05, 0.7, and 0.8 μg L⁻¹, respectively, to be reached. In microextraction, a fine silica fiber coated with a thin layer of polydimethylsiloxane is used. The partition coefficients of the analytes between the polymeric coating and water have been determined to be 40, 115, and 110 for THT, TBM, and benzene, respectively. When sampling is performed from the liquid phase, partition equilibrium is reached within 5 to 20 minutes, or more quickly when the solution is agitated. Using a flame ionization detector, detection limits for THT, TBM, and benzene were 3, 5, and 0.2 μg L⁻¹, respectively. Extraction of volatile or semi-volatile analytes can also be performed from the headspace with very similar detection limits. In addition, the extraction time is shorter since equilibrium is reached within 1 to 1.5 minute, which can again be reduced by agitation of the sample. The advantages and drawbacks of both techniques are gathered and discussed in this paper, which also underlines their complementarity.     

Comparison of on-line SPE-HPLC and SPME-GC for the analysis of microcontaminants in water

Summary Solid-phase preconcentration coupled on-line with liquid chromatography, and solid-phase microextraction coupled with gas chromatography have been applied to the determination of trace-level concentrations of benzene and sulfur compounds (tetrahydrothiophene (THT),t-butyl mercaptan (TBM), andn-butyl mercaptan (nBM)) in aqueous media. The first technique uses a microcolumn packed with a styrene-divinylbenzene copolymer. Retention values for THT, TBM, and benzene on this sorbent, expressed as the capacity factors, are 1100, 1600, and 4000, respectively. It is, therefore, possible to preconcentrate them efficiently and this method enables minimum concentrations of 0.05, 0.7, and 0.8 μg L⁻¹, respectively, to be reached. In microextraction, a fine silica fiber coated with a thin layer of polydimethylsiloxane is used. The partition coefficients of the analytes between the polymeric coating and water have been determined to be 40, 115, and 110 for THT, TBM, and benzene, respectively. When sampling is performed from the liquid phase, partition equilibrium is reached within 5 to 20 minutes, or more quickly when the solution is agitated. Using a flame ionization detector, detection limits for THT, TBM, and benzene were 3, 5, and 0.2 μg L⁻¹, respectively. Extraction of volatile or semi-volatile analytes can also be performed from the headspace with very similar detection limits. In addition, the extraction time is shorter since equilibrium is reached within 1 to 1.5 minute, which can again be reduced by agitation of the sample. The advantages and drawbacks of both techniques are gathered and discussed in this paper, which also underlines their complementarity.     

Determination of Polyvinyl Alcohol Using Gel Filtration Liquid Chromatography

Gel filtration chromatography using a TSKgel G2000 SW column coupled with differential refractive index detection was used to analyse five grades of polyvinyl alcohol. Limits of detection and quantification for the assay were 0.14 mg mL^–1, 0.47 mg mL^–1 respectively. The inter and intra-day co-efficient of variance were both <7%. There was a significant difference (p<0.05, n=5) between the calibration curves across the five grades of PVA due to a refractive index range of 13.0790 –1.3181 (n=3). The assay accuracy was 98.99% ± 8.97% (n=5) and 90.60% ± 7.87% (n=5) of a spiked PVA sample was recovered from a commercial formulation.     

Evaluation of the Temperature Responsive Stationary Phase Poly(N-isopropylacrylamide) in Aqueous LC for the Analysis of Small Molecules

Liquid chromatography columns were packed with a temperature responsive stationary phase based on poly(N-isopropylacrylamide) (PNIPAAm) attached to aminopropyl silicagel. This polymer shows hydrophilic properties below 32 °C and becomes hydrophobic above that temperature. The temperature responsive properties of the coupled phase are demonstrated using only water as mobile phase, whereby an increase in retention is observed with raising temperature. Mixtures of compounds covering a wide polarity range and including phenones, alkylbenzenes, phenols, alkylated benzoic acids, anilines, sulfonamides and carbamates were analyzed and the retention, peak shapes and plate counts were compared under identical conditions. For retained solutes, an increase in retention as a function of the temperature between 25 and 55 °C could be noted, whereby this was higher for the analytes containing a longer hydrophobic chain. Compounds with similar hydrophobic chains, but containing additional polar functions showed increased retention and improved peak shapes, suggesting a mixed mode interaction mechanism also at temperatures well above the transition temperature of the polymer. Weak acids and bases could be analyzed by pH adjustment. This is demonstrated for mixtures of benzoic acid derivatives and sulfamide drugs. A carbamate pesticide mixture was analyzed at 55 °C with water (pH 5.5) as mobile phase and ESI-MS detection. Temperature responsive stationary phases open perspectives for green chromatography.     

Comparison of Needle Concentrator with SPME for GC Determination of Benzene, Toluene, Ethylbenzene, and Xylenes in Aqueous Samples

A method of solventless extraction of volatile organic compounds from aqueous samples has been developed and validated. A new arrangement in which the internal volume of a needle capillary adsorption trap is completely filled with Porapak Q, as adsorbent material, and wet alumina, as a source of desorptive water vapor flow, is presented. The device has been used for head-space sampling of benzene, toluene, ethylbenzene, and xylenes (BTEX) from water samples and compared with solid-phase microextraction. Under the same sampling conditions the analytical characteristics of the device for the BTEX compounds are better than those of solid-phase microextraction. Limits of detection and quantification are below 0.5 μ g L⁻¹.     

LC Determination of Mono-Substituted Phenols in Water Using Liquid–Liquid–Liquid Phase Microextraction

A simple liquid–liquid–liquid microextraction device of new design was used to pre-concentrate phenols from water samples before liquid chromatographic (LC) analysis. Extraction was induced by the pH difference inside and outside an organic phase located at the interface. The pH of the donor phase outside the organic phase was adjusted to 1 with HCl whereas the acceptor phase was a basic solution at pH 13. On stirring neutral phenols were extracted into the organic solvent then back-extracted into 1 μL of basic acceptor solution suspended from the tip of a micro syringe. The acceptor phase was then withdrawn into the micro syringe and injected directly into the LC. The technique uses a low-cost disposable extraction ‘device’ and is very convenient to operate. Up to 230-fold enrichment of analytes could be achieved. This procedure could also serve as a sample clean-up step because neutral and basic compounds were not extracted into the acceptor phase. The RSD (n = 5) was better than 6.2% and the linear calibration range was from 1 to 1000 µg–L⁻¹ with r ² ≥ 0.992.Optimization of experimental conditions (rate of stirring, ionic strength of the sample solution, concentration of reagents, time of extraction, and organic solvent volume) were also examined. The method was applied to the determination of phenols in tap and well waters.Revised: 14 February and 29 March 2005     

LC Method for the Determination of NPC1161, Primaquine and their Metabolites in Various Biological Systems

NPC1161 is an 8-aminoquinoline anti-malarial analog, which has a favorable toxicity profile relative to primaquine and other 8-aminoquinolines. High-performance liquid chromatographic method was developed for the determination of NPC1161, primaquine and their metabolites in biological samples in order to facilitate metabolic and pharmacokinetic studies. The method includes extraction of the unchanged drugs and their metabolites from the biological samples. Separation was achieved by reversed-phase chromatography on a C18 column with water–acetonitrile both containing 0.025% trifluoroacetic acid as the mobile phase. Recoveries of NPC1161 and its metabolites were greater than 60% in various biological samples tested. No interference with the components of the biological material was observed. The detector response was linear with concentrations of NPC1161 and its metabolites (desalkyl NPC1161 and carboxy NPC1161) in the ranges from 0.5 to 80.0, 0.4–60.0 and 0.4–70.0 μg mL⁻¹, respectively. A mass spectrometry coupled with electrospray ionization (ESI) interface method is described for the identification of NPC1161 and its metabolites in biological samples. This method involved the use of the [M + H]⁺ions of NPC1161, C3 analog (internal std. for the assay), desalkyl NPC1161 and carboxy NPC1161 at m/z 434, 406, 349 and 449 in the positive ion mode with extractive ion monitoring (EIM). This method will have an important application in pharmacokinetic studies of NPC1161 and in understanding the mechanism of metabolism of this novel 8-aminoquinoline analog in more detail.     

Quantitative Determination of Acyclovir in Aqueous Humor by LC-MS

A specific, sensitive and precise liquid chromatographic assay method was established using LC-MS for the determination of acyclovir (ACV) in aqueous humor (AH), which was directly injected onto an Inertsil ODS-3 C₁₈ column without any pretreatment. The Agilent 1100 series LC–MS system was operated under the electrospray ionization mode (ESI). The analyte was separated from endogenous substances with a mobile phase of methanol: water: acetic acid (5:95:0.1, v/v) at a flow-rate of 0.3mL min⁻¹. A linear response was observed over the concentration range from 5 to 50ng mL⁻¹ (r=0.9993). Intra- and inter-day coefficients of variation were in the ranges 5.2–9.0% and 5.8–8.2%, respectively. The recovery was > 91.0%, and the limit of detection was approximate 1ng mL⁻¹. The pharmacokinetics of topically applied eye-drop and thermosetting gel were compared in rabbits utilizing the present method, the results demonstrated that LC-MS was a powerful tool for the detection of ACV in AH.     

Solid-phase microextraction coupled with microcolumn liquid chromatography for the analysis of amitriptyline in human urine

Summary Solid-phase microextraction (SPME) is a solvent-free sample-preparation technique that enables isolation and pre-concentration of analytes from a sample on a thin film coating a fused-silica fiber. In this study SPME coupled with microcolumn liquid chromatography (micro LC) has been used for the determination of four tricyclic antidepressants (amitriptyline, imipramine, nortriptyline, and desipramine) in human urine. SPME conditions which affect extraction efficiency were optimized, and under the optimum conditions the system was a few hundred times more sensitive than direct LC analysis without SPME. For amitriptyline the detection limit was 3 ng mL⁻¹ and the calibration curve was linear in the range of 5–500 ng mL⁻¹. The SPME-micro LC method has been applied to the analysis of amitriptyline in patient’s urine.     

LC Determination of Anethole in Aniseed Drinks

A method for the determination of anethole in aniseed drinks by high performance liquid chromatography (HPLC) is proposed. A C-18 column and a methanol-water (80:20, v/v) mobile phase with isocratic elution were used. UV detection at 257 nm was carried out. Validation was performed according to the EURACHEM guidelines, considering precision, trueness, robustness, linearity and sensitivity. The detection and quantification limits were 2.3 and 7.7 μg L⁻¹, respectively. Recoveries of 95–101% were obtained. Repeatability, calculated as relative standard deviation was 0.9%. Reproducibility under intermediate precision conditions, expressed as relative standard deviation, was 1.6%. The method was compared with the gas chromatographic one, proposed by the European regulations.     

Determination of Herbicides in Natural Waters Using Solid Phase Microextraction (SPME) and Gas Chromatography Coupled with Flame Thermionic and Mass Spectrometric Detection

Abstract

This study develops a method for solid phase microextraction (SPME) of ten widespread herbicides from water. The selected herbicides belong to different chemical groups are EPTC, molinate, propachlor, trifluralin, atrazine, propazine, terbuthylazine, prometryne, alachlor. Their determination was carried out by gas chromatography with flame thermionic and mass spectrometric detection. To perform the SPME, two types of fibre have been assayed: Carbowax-divinylbenzene (CW-DVB) of 65 μm thickness and polydimethylsiloxane-divinylbenzene (PDMS-DVB) of 65 μm thickness. The main factors affecting the SPME process such as pH, ionic strength, methanol content, memory effect, stirring rate and adsorption-time profile were studied. The method was applied to spiked natural waters such as ground water, sea water, lake water and river water in a concentration range of 0.1 to 10 μg/L. Limits of detection with each of the detectors were determined to be 1 – 20 ng/L in PDMS-DVB and 2–20 ng/L CW-DVB fibres. The recoveries of herbicides compared to distilled water were in relatively high levels 78.3–127.3 % and the average r² values of the calibration curves were above 0.99 for all the analytes. The SPME conditions were finally optimized in order to obtain maximum sensitivity and samples were applied for the trace-level determination in river water samples originating from Ioannina region (Greece).