用1-亚硝基-2-萘酚修饰的微晶蒽分离富集与测定环境水中钴

建立了微晶蒽分离富集环境水样中痕量Co(II)的方法。在pH3.0条件下,1-亚硝基-2-萘酚与Co(II)形成红棕色螯合物被微晶蒽定量吸附,能使Co(II)与Pb(II)、Ni(II)、Mn(II)、Cu(II)、Cd(II)、Zn(II)、Fe(III)、Cr(III)、Al(III)等常见离子分离。本法富集倍数达100倍,检出限为0.14μg/L,回收率97.5%～105%,已应用于不同水样中Co(II)的测定。     

Determination of Co(II) by chemiluminescence after in situ electrochemical pre-separation on a flow-through mercury film electrode

A novel method of electrochemical pre-separation of Co(II) before detection by chemiluminescence is reported together with the associated instrumentation. The Co(II) ions were selectively pre-separated on a mercury film electrode (MFE) by on-line reduction, then the accumulated metal was oxidised and selectively stripped back into the flowing solution as Co(II). These secondary ions were quantified as a result of their catalytic activity on the chemiluminescent reaction between luminol and hydrogen peroxide that was also induced on-line. The whole sequence was carried out in an automated flow-through system, in which the electrochemical pre-separation of metals was performed in either continuous flow or flow injection analysis (FIA) regimes. The scope of the method, both in terms of selectivity and sensitivity, has been demonstrated and the quantitative determination of Co(II) by the proposed method has been investigated. For a period of continuous flow pre-separation of 4 min, the calibration curve for Co(II) was linear up to a concentration of 100 micrograms l-1, the relative standard deviation was 4% at the 20 micrograms l-1 level and the limit of detection was 0.5 microgram l-1 (at the 3 sigma level). The method was applied to the determination of the cobalt content in a high purity iron sample.     

Kinetic Analysis of Cobalt in Veterinary Products

A novel kinetic method for the determination of trace amounts of Co(II) has been developed. The proposed method based on the catalytic effect of Co(II) on the oxidation of xylenol orange tetra sodium salt by H₂O₂ in the presence of cationic surfactant (N‐dodecylpyridinium chloride). Co(II) at μg.mL^?1 was determined spectrophotometrically by measuring the decrease in the absorbance of xylenol orange at 577 nm by the differential method. The method is precise, selective, and sensitive. The detection limit of the procedure was 0.058 μg.mL^?1. The relative standard deviation for the replicate determination (n = 6) of 0.7 μg.mL^?1 was 1.285%. The results compared satisfactorily with those of atomic absorption spectrometry. The method was successful for the analysis of Co(II) in veterinary and synthetic samples.     

微晶酚酞富集-分光光度法测定痕量Zn(II)

建立了一种利用修饰有结晶紫(CV^＋)的微晶酚酞作为固态吸附剂分离富集溶液中痕量Zn(II)的新方法, 富集后的Zn(II)含量可直接用光度法测定. 控制一定条件, Zn(II)能与常见阳离子Ni(II), Cd(II), Al(III), Ca(II), Mg(II), Co(II), Mn(II), Cu(II), Pb(II), Fe(III)等完全分离, 且富集时基本不受, , Br^－, Cl^－, I^－,等阴离子影响. 微晶酚酞对Zn(II)的吸附容量为25.8 mg/g; 富集因数可达200倍, 回收率在97.7%～102%之间, RSD小于2.7%. 该方法已成功应用于实际水样中Zn(II)的富集测定, 结果令人满意.     

Cu(II)-3-(5-chlor-2-hydroxy-3-sulfophenylazo)-6-(2,4,6-tribromophenylazo)-4,5-dihydroxynaphthalene-2,7-disulfonic Acid-Co(II) binuclear complexation and its application to the selective determination of cobalt at ng/ml level.

The chromophore, 3-(5-chlor-2-hydroxy-3-sulfophenylazo)-6-(2,4,6-tribromophenylazo)-4,5-dihydroxynaphthalene-2,7-disulfonic acid (CSTDD) was used to complex Cu(II) and Co(II) in aqueous solution at pH 9.43. A binuclear complex of Cu-CSTDD-Co was formed and showed a high selectivity for the determination of Co(II). The spectral correction technique was applied to characterize the complexes. The results showed the formation of complexes of Cu(CSTDD), Co(CSTDD)3 and Cu2(CSTDD)2Co. The quantitative analysis of Co(II) at ng/ml level was carried out by the light-absorption ratio variation approach (LARVA). The results showed that the technique is satisfactory to determine Co(II) at trace level in water samples with a detection limit of 2.3 ng/ml.     

Simultaneous spectrophotometric determination of trace amounts of cobalt, nickel, and copper using the partial least-squares method after the preconcentration of their 2-aminocyclopentene-1-dithiocarboxylate complexes on microcrystalline naphthalene

A spectrophotometric method for the determination of trace amounts of cobalt(II), nickel(II), and copper(II) after the adsorption of their 2-aminocyclopentene-1-dithiocarboxylate complexes on microcrystalline naphthalene has been developed. These complexes are adsorbed on microcrystalline naphthalene at pH 4.5 by shaking for 5 min. The formed solid mass is separated by filtration, and dissolved in dimethylformamide. The absorption spectra were processed using the partial least-squares multivarate calibration method for the analysis of a ternary mixture of Co(II), Ni(II), and Cu(II). The detection limits for Co(II), Ni(II), and Cu(II) were 3.3, 10.0, and 0.8 ng/mL, respectively. The total relative standard error for applying the method to 20 synthetic samples in the concentration ranges of 20–400 ng/mL Co(II), 60–400 ng/mL Ni(II), and 4–400 ng/mL Cu(II) was 1.53%. The proposed method was also successfully applied to the determination of Co(II), Ni(II), and Cu(II) in alloys. The text was submitted by the authors in English.     

Study on Preconcentration of Trace Copper Using Microcrystalline Triphenylmethane Loaded with Malachite Green

The paper describes a novel method for copper preconcentration using microcrystalline triphenylmethane loaded with malachite green prior to the determination by the flame atomic absorption spectrometry （FAAS）. Under the optimum conditions, Cu（Ⅱ） can be totally adsorbed on the surface of microcrystalline triphenylmethane, and completely separated from Pb（Ⅱ）, Cd（Ⅱ）, Co（Ⅱ）, Cr（Ⅲ）, Ni（Ⅱ）, Mn（Ⅱ）, Fe（Ⅲ） and Al（Ⅲ） by controlling acidity. The preconcentration factor of this proposed method is 200. The recovery is in a range of 97.5%-105%. The relative standard deviation （RSD） is not beyond 3.0%. The proposed method has been successfully applied to the determination of trace copper in various water samples with satisfactory results.     

Separation and extraction of Co(II) using magnetic chitosan nanoparticles grafted with β-cyclodextrin and determination by FAAS

A novel and selective method for the fast determination of trace amounts of Co(II) ions in water samples has been developed. The procedure is based on the selective sorption of Co(II) ions using magnetic chitosan nanoparticles grafted with β-cyclodextrin at different pH followed by elution with organic eluents and determination by atomic absorption spectrometry The preconcentration factor was 100 (1 mL elution volume) for a 100 mL sample volume. The limit of detection of the proposed method is 1.0 ng mL^?1. The maximum sorption capacity of sorbent under optimum conditions has been found to be 5 mg of Co per gram of sorbent. The relative standard deviation under optimum conditions was 3.0% (n = 10). Accuracy and applicability of the method was estimated using test samples of natural and model water with different amounts of Co(II).     

Kinetic determination of trace cobalt(II) by visual autocatalytic indication

A highly sensitive and simple visual autocatalytic method has been developed for the determination of trace cobalt. The cobalt ion released by the oxidative decomposition of inert bis[2-(5-bromo-2-pyridylazo)-5-(N-propyl-N-sulfopropyl-amino-phenolato] cobaltate (Co(III)-5-Br-PAPS) with peroxomonosulfate acts as a catalyst for the oxidative degradation of the complex. Thus a definite time lapse of degradation is observed by the sudden disappearance of colored Co(III) complexes. The degradation time varies inversely with the logarithm of the initial concentration of cobalt(II). The determination range of cobalt(II) was from 3x10(-9) to 2x10(-7) M in the presence of 5x10(-6) M of 5-Br-PAPS. The relative standard deviation of the spot size method (10 mul) was 3.5% at 1x10(-7) M cobalt(II). This autocatalytic indicator reaction system has been successfully applied for the visual determination of urinary cobalt.     

Adsorptive cathodic stripping voltammetry determination of ultra trace levels of cobalt

The complexation of Co(II) with 4-(2-pyridylazo)resorcinol (PAR) was studied by spectroscopy and voltammetry. In addition, an adsorptive stripping voltammetric method was developed for the determination of ultra trace levels of Co(II) using a hanging mercury drop electrode. The method is based on accumulation of Co(II) on a mercury electrode using PAR as the complexing agent. The effects of instrumental and chemical parameters on the sensitivity of the method were investigated. The detection limit of the method is 0.003 ng/mL. Most foreign species do not interfere with the determination. The high sensitivity and selectivity of this method were demonstrated by determination of cobalt in blood and water samples.     

Development of a flow-through optosensor for determination of Co(II)

A flow-through optical fibre chemical sensor for the determination of Co(II) at trace level using immobilised 2-(4-pyridylazo)resorcinol (PAR) as the reagent phase is proposed. PAR is physically adsorbed onto XAD-7. This method provided a great sensitivity and simplicity with wide linear response range from 1x10(-2) to 1x10(3)ppm and detection limit of 20ppb. This method also showed a reproducible result with relative standard deviation (R.S.D.) of 1.78% and response time of approximately 5min. The response towards Co(II) was also reversible using acidified KCl as the regenerating solution. Interference studies showed that Cr(III) significantly interfered during the determination. Excellent agreement with reference to inductively coupled plasma optical emission spectroscopy (ICPOES) method was achieved when the developed sensor was applied for determination of Co(II) in aqueous samples.     

Potential of Modified Multiwalled Carbon Nanotubes with 1-(2-Pyridylazo)-2-naphtol as a New Solid Sorbent for the Preconcentration of Trace Amounts of Cobalt(II) Ion

The present paper reports on the application of modified multiwalled carbon nanotubes (MMWCNTs) as a new, easily prepared and stable solid sorbent for the preconcentration of trace Co(II) in aqueous solution. Multiwalled carbon nanotubes (MWCNTs) were oxidized with concentrated HNO(3) and modified with 1-(2-pyridylazo)-2-naphtol (PAN), and were then used as a solid phase for the preconcentration of Co(II). Factors influencing the sorption and desorption of Co(II) were investigated. Elution was carried out with 0.5 mol L(-1) HNO(3). The amount of eluted Co(II) was measured using flame atomic absorption spectrometry. The effects of the experimental parameters, including the sample pH, sample flow rate, eluent flow rate and eluent concentration, were investigated. The effect of coexisting ions showed no interference from most ions tested. The proposed method permitted a large enrichment factor (about 300). The precision of the method was 1.63% (for eight replicate determination of 0.5 microg mL(-1) of Co(II)) and the limit of detection was 0.55 ng mL(-1). The method was applied to the determination of Co(II) in water, biological and standard samples.     

Simultaneous Determination of Cobalt and Nickel Using Morpholinedithiocarbamate (MDTC) as Reagent by First and Second Derivative Spectrophotometry

A selective and sensitive derivative method has been proposed for the simultaneous determination of trace amounts of Co(II) and Ni(II) with morpholinedithiocarbamate (MDTC) in the presence of sodium lauryl sulphate (SLS). The molar absorption coefficients of the 1:2 complex of Co(II) and Ni(II) at 326 nm and 322 nm are 2.248 × 10⁴ and 2.505 × 10⁴ L mol^?1 cm^?1 for zero order. The analytical sensitivity for the second derivative of Co(II) and Ni(II) complexes are 0.0044 μg mL^?1 and 0.0060 μg mL^?1. The developed derivative procedure, using the zero‐crossing technique, has been successfully applied for the analysis of Co(II) and Ni(II) simultaneously in different alloy samples.     

Pre-column chelation liquid chromatographic separation and determination of trace V,Cu, Co,Pd, Fe and Ni

Conditions for the separation by reversed-phase liquid chromatography (LC) of V(V), Cu(II), Co(III), Pd(II), Fe(III) and Ni(II) chelates with 2-(5-bromopyridylazo)-5-diethylaminophenol (5-Br-PADAP) were studied. Six species of metal chelates were separated successfully with methanol-acetonitrile-water (72:12:16, v/v/v) containing 0.13 M NaCl and 0.29 mM cetyltrimethylammonium bromide (pH 5.0) as the mobile phase on a Nucleosil C₁₈ (5 μm) column (250 × 4 mm i.d.).The conditions of the determination of these metal chelates are discussed. A simple and rapid method for the determination of trace amounts of V(V), Cu(II), Co(III), Pd(II) and Ni(II) simultaneously by reversed-phase LC has been developed. The detection limits are 5 × 10^?12, 1 × 10^?10, 3 × 10^?11, 5.3 × 10^?9 and 2 × 10^?10 g, respectively. The method is applied to the determination of these metals in natural waters and mineral samples.     

H-point standard addition method for simultaneous determination of Fe(II), Co(II) and Cu(II) in micellar media with simultaneous addition of three analytes

H-point standard addition method, HPSAM, with simultaneous addition of three analytes is proposed for the resolution of ternary mixtures. It is a modification of the previously described H-point standard addition method that permits the resolution of three species from a unique calibration set by making the simultaneous addition of the three analytes. The method calculates the analyte concentration from spectral data at two wavelengths where the two species selected as interferents present the same absorbance relationship. These wavelength pairs are easily found, and can be selected to give the most precise results. Diethyldithiocarbomate (DDC) in a cationic micellar solution of cetyltrimethylammonium bromide (CTAB) was used for determination of Fe(II), Co(II) and Cu(II) at pH 5.50. The results showed that simultaneous determination of Fe(II), Co(II) and Cu(II) could be preformed in the range of 0.0–6.0, 0.0–8.0 and 0.0–12.0 μg ml⁻¹, respectively. The proposed method was successfully applied to the simultaneous determination of Fe(II), Co(II) and Cu(II) in several synthetic mixtures containing different concentration of Fe(II), Co(II) and Cu(II).     

Single-use optical sensor for the determination of iron in water and white wines

A new method, based on the use of a disposable sensor, for the determination of Fe(II) in waters and wines is proposed. The sensor is formed by an inert rectangular strip of polyester (Mylar) and a circular film (6 mm in diameter) adhered on its surface. This film, which contains the required reagents for the fixation of the analyte by means of a complexation reaction, forms the sensing zone of the sensor. When the sensor is introduced in an acidified (pH 2.5) sample solution containing between 4.0 and 300.0 micrograms/L of Fe(II), a violet-red colour develops in the initially colourless sensing zone. The linear range of the method depends on the equilibration time of the sensor with the sample solution. Thus, when the equilibration time was 5 min, the linear range was 41.0-300.0 micrograms/L, while for 60 min the range was 4.0-50.0 micrograms/L. Detection and quantification limits were 12.0 and 41.0 micrograms/L, respectively, for an equilibration time of 5 min. The precision of the method, expressed as relative standard deviation of ten samples of 100.0 micrograms/L of Fe(II), was 4.9%. Interferences produced by other species usually present in waters or wines have been studied. Cu(II) and Co(II) interfered seriously at concentration levels higher than 100.0 and 150.0 micrograms/L, respectively. The method was applied to the determination of Fe(II) in different types of waters and wines, using atomic absorption spectrometry as a reference method.     

Selective solid-phase extraction of nickel(II) using a surface-imprinted silica gel sorbent

A new Ni(II)-imprinted amino-functionalized silica gel sorbent with excellent selectivity for nickel(II) was prepared by an easy one-step reaction by combining a surface imprinting technique for selective solid-phase extraction (SPE) of trace Ni(II) in water samples prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Compared with non-imprinted polymer particles, the ion-imprinted polymers (IIPs) had higher selectivity and adsorption capacity for Ni(II). The maximum static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Ni(II) was 12.61 and 4.25 mg g⁻¹, respectively. The relatively selective factor (α_r) values of Ni(II)/Cu(II), Ni(II)/Co(II), Ni(II)/Zn(II) and Ni(II)/Pd(II) were 45.99, 32.83, 43.79 and 28.36, which were greater than 1. The distribution ratio (D) values of Ni(II)-imprinted polymers for Ni(II) were greatly larger than that for Cu(II), Co(II), Zn(II) and Pd(II). The detection limit (3σ) was 0.16 ng mL⁻¹. The relative standard deviation of the method was 1.48% for eight replicate determinations. The method was validated by analyzing two certified reference materials (GBW 08618 and GBW 08402), the results obtained is in good agreement with standard values. The developed method was also successfully applied to the determination of trace nickel in plants and water samples with satisfactory results.     

Multiresidue analytical method for the determination of eight penicillin antibiotics in muscle tissue by ion-pair reversed-phase HPLC after precolumn derivatization.

A high-performance liquid chromatographic multiresidue method was developed for the determination of 8 penicillin compounds (benzylpenicillin, phenoxymethylpenicillin, ampicillin, amoxicillin, nafcillin, oxacillin, cloxacillin, and dicloxacillin) at trace levels in muscle tissue. This method involves extraction of the penicillins with phosphate buffer pH 9 followed by cleanup and concentration on a C18 solid-phase extraction column and reaction with benzoic anhydride at 50 degrees C for 5 min and with 1,2,4-triazole and mercury(II) chloride solution pH 9 at 65 degrees C for 10 min. The derivatized compounds are eluted on a C8 column with a mobile phase containing acetonitrile and phosphate buffer (pH 6; 0.1 mol/L) loaded with sodium thiosulfate and ion-pairing tetrabutylammonium hydrogenosulphate. The method detection limit is approximately 3-11 micrograms/kg and the limit of determination was evaluated down to 25 micrograms/kg in line with the criteria of the EU decision No. 93/256/EEC.     

The Fe(II) and Co(II) chelation complexes of 2,6-BIS(4-Ethyl-2-Pyridyl)-4-Phenyl-Pyridinl

A study has been made of the spectrophotometric constants of the new modified terpyridine chelation reagent, 2,6-bis(4-ethyl-2-pyridyl)-4-phenyl-pyridine (trivial name “ethyl-terosole”), as its Fe(II) and Co(II) complex cations. This new Iigand is outstanding for use in the trace quantity determination of iron. No advantage as compared to more sensitive ligands previously studied is provided by Co(II) chelation.     

Accumulation and voltammetric determination of cobalt at zeolite-modified electrodes

Chemically modified electrodes based on zeolite-containing graphite pastes were constructed and evaluated as sensor electrodes for the voltammetric determination of trace cobalt in solution. Zeolite molecular sieves with pore sizes of 3, 4, and 5 Å were all suitable for chemical deposition and subsequent voltammetric quantitation of trace Co(II). In order to cover a large range of parameters, the investigations were carried out using three zeolites (A, X, and Y), selected for their different cation-exchange capacities and ion-sieving properties. The analytical scheme, “preconcentration/voltammetric detection” for the determination of cobalt(II) species using zeolite-modified carbon paste electrodes (ZMCPE) was chosen. Compared to the corresponding unmodified electrodes, improvements in sensitivity were observed when using ZMCPEs due to analyte accumulation at the electrode’s surface by ion exchange in zeolite particles. The detection limit obtained for Co(II) was 3 ppm following 15 min of chemical deposition. A good correlation was found between the results obtained by ion exchange voltammetry and conventional ion-exchange characterization.