C60 sputtering of organics: A study using TOF-SIMS, XPS and nanoindentation

Sputtering of organic materials using a C₆₀ primary ion beam has been demonstrated to produce significantly less accumulated damage compared to sputtering with monatomic and atomic-cluster ion beams. However, much about the dynamics of C₆₀ sputtering remains to be understood. We introduce data regarding the dynamics of C₆₀ sputtering by evaluating TOF-SIMS depth profiles of bulk poly(methyl methacrylate) (PMMA). Bulk PMMA provides an ideal test matrix with which to probe C₆₀ sputter dynamics because there is a region of steady-state secondary ion yield followed by irreversible signal degradation. C₆₀ sputtering of PMMA is evaluated as a function of incident ion kinetic energy using 10 keV C₆₀⁺, 20 keV C₆₀⁺ and 40 keV C₆₀⁺⁺ primary ions. Changes in PMMA chemistry, carbon accumulation and graphitization, and topography as a function of total C₆₀ ion dose at each accelerating potential is addressed.     

Characterization and ion-induced degradation of cross-linked poly(methyl methacrylate) studied using time of flight secondary ion mass spectrometry

In this study, a series of random copolymers of methyl methacrylate (MMA) and ethylene glycol dimethacrylate (EGDMA) were prepared as surface-initiated polymer (SIP) films on silicon substrates using atom transfer radical polymerization. Positive and negative ion static time-of-flight secondary ion mass spectrometry (ToF-SIMS) was used to characterize SIP films with different MMA/EGDMA monomer ratios in an attempt to quantify their surface composition. However, matrix effects in the positive and negative ion modes led to preferential secondary ion generation from the EGDMA monomer and suppression of secondary ions characteristic of the MMA monomer, precluding accurate quantification using standard linear quantification methods. Ion-induced degradation of these films under 5 keV SF₅⁺ bombardment was also examined to determine the effect of cross-linking on the accumulation of ion-induced damage. Increasing incorporation of the EGDMA cross-linker in the SIP films decreased the sputter rate and increased the rate of damage accumulation under extended (>10¹⁴ ions/cm²) 5 keV SF₅⁺ bombardment. Comparison of the ion bombardment data with thermal degradation of cross-linked PMMA suggests that the presence of the cross-linker impedes degradation by depolymerization, resulting in ion-induced damage accumulation. The increased rate of ion-induced damage accumulation with increased cross-link density also suggests that polymers that can form cross-links during ion bombardment are less amenable to depth profiling using polyatomic primary ions.     

Cluster SIMS using metal cluster complex ions

Metal cluster complexes are chemically synthesized organometallic compounds, which have a wide range of chemical compositions with high molecular weight. Using a metal cluster complex ion source, sputtering characteristics of silicon bombarded with normally incident Ir₄(CO)₇⁺ ions were investigated. Experimental results showed that the sputtering yield at 10 keV was 36, which is higher than that with Ar⁺ ions by a factor of 24. In addition, secondary ion mass spectrometry (SIMS) of boron-delta-doped silicon samples and organic films of poly(methyl methacrylate) (PMMA) was performed. Compared with conventional O₂⁺ ion beams, Ir₄(CO)₇⁺ ion beams improved depth resolution by a factor of 2.5 at the same irradiation conditions; the highest depth resolution of 0.9 nm was obtained at 5 keV, 45° with oxygen flooding of 1.3 × 10⁻⁴ Pa. Furthermore, it was confirmed that Ir₄(CO)₇⁺ ion beams significantly enhanced secondary ion intensity in high-mass region.     

Biomimetic, hierarchical structures on polymer surfaces by sequential imprinting

Thermal nanoimprint lithography (NIL) is based on the thermo-mechanical deformation of a polymer film above the glass transition temperature (T_g) and at an applied pressure. Sequential imprinting extends the process of thermal NIL to create hierarchical structures by carrying out secondary and tertiary imprintings at temperatures below the T_g of a polymer. In this work, we demonstrate the use of sequential imprinting technique to fabricate two- and three-level hierarchical structures on polystyrene (PS) and poly(methyl methacrylate) (PMMA) films over a temperature range of 70-130 °C, with the aim to mimic the hierarchical structures found in biological systems. By mimicking the hierarchical structure in a plant leaf, the water contact angle of PS film was increased from 95° to 128°, while the water contact angle of PMMA film was increased from 71° to 104°, without any chemical treatment.     

The effect of C60 cluster ion beam bombardment in sputter depth profiling of organic-inorganic hybrid multiple thin films

The effects of C₆₀ cluster ion beam bombardment in sputter depth profiling of inorganic-organic hybrid multiple nm thin films were studied. The dependence of SIMS depth profiles on sputter ion species such as 500 eV Cs⁺, 10 keV C₆₀⁺, 20 keV C₆₀²⁺ and 30 keV C₆₀³⁺ was investigated to study the effect of cluster ion bombardment on depth resolution, sputtering yield, damage accumulation, and sampling depth.     

Thermal stability of alumina thin films containing γ-Al2O3 phase prepared by reactive magnetron sputtering

The paper reports on thermal stability of alumina thin films containing γ-Al₂O₃ phase and its conversion to a thermodynamically stable α-Al₂O₃ phase during a post-deposition equilibrium thermal annealing. The films were prepared by reactive magnetron sputtering and subsequently post-deposition annealing was carried out in air at temperatures ranging from 700 °C to 1150 °C and annealing times up to 5 h using a thermogravimetric system. The evolution of the structure was investigated by means of X-ray diffraction after cooling down of the films. It was found that (1) the nanocrystalline γ-Al₂O₃ phase in the films is thermally stable up to 1000 °C even after 5 h of annealing, (2) the nanocrystalline θ-Al₂O₃ phase was observed in a narrow time and temperature region at ≥1050 °C, and (3) annealing at 1100 °C for 2 h resulted in a dominance of the α-Al₂O₃ phase only in the films with a sufficient thickness.     

Effects of the substrate temperature on the properties of CuIn5S8 thin films

Structural, optical and electrical properties of CuIn₅S₈ thin films grown by thermal evaporation have been studied relating the effects of substrate heating conditions of these properties. The CuIn₅S₈ thin films were carried out at substrate temperatures in the temperature range 100-300 °C. The effects of heated substrate on their physico-chemical properties were investigated using X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), optical transmission and hot probe method. X-ray diffraction revealed that the films are strong preferred orientation along the (3 1 1) plane upon substrate temperature 200 °C and amorphous for the substrate temperatures below 200 °C. No secondary phases are observed for all the films. The composition is greatly affected by heated substrate. From the optical transmission and reflection, an important absorption coefficient exceeds 10⁵ cm⁻¹ at 800 nm was found. As increasing the substrate temperature, the optical energy band gap decreases from 1.70 eV for the unheated films to 1.25 eV for the deposited films at 300 °C. It was found that CuIn₅S₈ thin film is an n-type semiconductor at 250° C.     

Characterization of drug-eluting stent (DES) materials with cluster secondary ion mass spectrometry (SIMS)

Secondary ion mass spectrometry (SIMS) employing an SF₅⁺ polyatomic primary ion source was utilized to analyze several materials commonly used in drug-eluting stents (DES). Poly(ethylene-co-vinyl acetate) (PEVA), poly(lactic-co-glycolic acid) (PLGA) and various poly(urethanes) were successfully depth profiled using SF₅⁺ bombardment. The resultant molecular depth profiles obtained from these polymeric films showed very little degradation in molecular signal as a function of increasing SF₅⁺ primary ion dose when experiments were performed at low temperatures (signal was maintained for doses up to ∼5 × 10¹⁵ ions/cm²). Temperature was determined to be an important parameter in both the success of the depth profiles and the mass spectral analysis of the polymers. In addition to the pristine polymer films, paclitaxel (drug released in Taxus™ stent) containing PLGA films were also characterized, where it was confirmed that both drug and polymer signals could be monitored as a function of depth at lower paclitaxel concentrations (10 wt%).     

Investigation of molecular weight effects of polystyrene in ToF-SIMS using C60 and Au primary ion beams

In secondary ion mass spectrometry, polyatomic primary ion sources are known to enhance yields from many surfaces including polymers. In order to understand the fundamental causes for these increases, the enhancement as a function of material type and molecular weight needs to be delineated. In this article, we report results from a systematic investigation of polymeric films of polystyrene (PS) with varying molecular weights to examine the influence of the primary ion beam on the secondary ion yields in time of flight secondary ion mass spectrometry (ToF-SIMS). The masses of the polymers investigated ranged from 1000 to 20,000 Da, or from about n = 10 to 200 where n indicates the number of polymeric units in a polymer chain. The polymers had a narrow molecular weight range (PDI < 1.07). The multilayer polymeric films (10-30 nm) characterized by AFM were prepared by spin-casting onto silicon substrates and were analyzed using Au⁺ and C₆₀⁺ primary ion beams. The analysis with the two beams provided a useful comparison between atomic and polyatomic primary ion sources. Information gathered from this study provides insight into the role of molecular weight on the observed yield enhancement from polyatomic ion sources.     

Influence of deposition temperature on the structural and morphological properties of Be3N2 thin films grown by reactive laser ablation

Be₃N₂ thin films have been grown on Si(1 1 1) substrates using the pulsed laser deposition method at different substrate temperatures: room temperature (RT), 200 °C, 400 °C, 600 °C and 700 °C. Additionally, two samples were deposited at RT and were annealed after deposition in situ at 600 °C and 700 °C. In order to obtain the stoichiometry of the samples, they have been characterized in situ by X-ray photoelectron (XPS) and reflection electron energy loss spectroscopy (REELS). The influence of the substrate temperature on the morphological and structural properties of the films was investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD). The results show that all prepared films presented the Be₃N₂ stoichiometry. Formation of whiskers with diameters of 100-200 nm appears at the surface of the films prepared with a substrate temperature of 600 °C or 700 °C. However, the samples grown at RT and annealed at 600 °C or 700 °C do not show whiskers on the surface. The average root mean square (RMS) roughness and the average grain size of the samples grown with respect the substrate temperature is presented. The films grown with a substrate temperature between the room temperature to 400 °C, and the sample annealed in situ at 600 °C were amorphous; while the αBe₃N₂ phase was presented on the samples with a substrate temperature of 600 °C, 700 °C and that deposited with the substrate at RT and annealed in situ at 700 °C.     

Influence of Si-N interlayer on the microstructure and magnetic properties of γ′-Fe4N films

The (γ′-Fe₄N/Si-N)_n (n: number of layers) multilayer films and γ′-Fe₄N single layer film synthesized on Si (1 0 0) substrates by direct current magnetron sputtering were annealed at different temperatures. The structures and magnetic properties of as-deposited films and films annealed at different temperatures were characterized using X-ray diffraction, scanning electron microscopy and vibrating sample magnetometer. The results showed that the insertion of Si-N layer had a significant influence on the structures and magnetic properties of γ′-Fe₄N film. Without the addition of Si-N lamination, the iron nitride γ′-Fe₄N tended to transform to α-Fe when annealed at the temperatures over 300 °C. However, the phase transition from γ′-Fe₄N to ?-Fe₃N occurred at annealing temperature of 300 °C for the multilayer films. Furthermore, with increasing annealing temperature up to 400 °C or above, ?-Fe₃N transformed back into γ′-Fe₄N. The magnetic investigations indicated that coercivity of magnetic phase γ′-Fe₄N for as-deposited films decreased from 152 Oe (for single layer) to 57.23 Oe with increasing n up to 30. For the annealed multilayer films, the coercivity values decreased with increasing annealing temperature, except that the film annealed at 300 °C due to the appearance of phase ?-Fe₃N.     

3D molecular imaging SIMS

Thin monolayer and bilayer films of spin cast poly(methyl methacrylate) (PMMA), poly(2-hydroxyethyl methacrylate) (PHEMA), poly(lactic) acid (PLA) and PLA doped with several pharmaceuticals have been analyzed by dynamic SIMS using SF₅⁺ polyatomic primary ion bombardment. Each of these systems exhibited minimal primary beam-induced degradation under cluster ion bombardment allowing molecular depth profiles to be obtained through the film. By combing secondary ion imaging with depth profiling, three-dimensional molecular image depth profiles have been obtained from these systems. In another approach, bevel cross-sections are cut in the samples with the SF₅⁺ primary ion beam to produce a laterally magnified cross-section of the sample that does not contain the beam-induced damage that would be induced by conventional focussed ion beam (FIB) cross-sectioning. The bevel surface can then be examined using cluster SIMS imaging or other appropriate microanalysis technique.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Thermoluminescent and stuctural properties of BaAl2O4:Eu,Nd,Gdphosphors prepared by combustion method

BaAl₂O₄:Eu²⁺,Nd³⁺,Gd³⁺ phosphors were prepared by a combustion method at different initiating temperatures (400–1200 °C), using urea as a comburent. The powders were annealed at different temperatures in the range of 400–1100 °C for 3 h. X-ray diffraction data show that the crystallinity of the BaAl₂O₄ structure greatly improved with increasing annealing temperature. Blue-green photoluminescence, with persistent/long afterglow, was observed at 498 nm. This emission was attributed to the 4f⁶5d¹–4f⁷ transitions of Eu²⁺ ions. The phosphorescence decay curves were obtained by irradiating the samples with a 365 nm UV light. The glow curves of the as-prepared and the annealed samples were investigated in this study. The thermoluminescent (TL) glow peaks of the samples prepared at 600 °C and 1200 °C were both stable at ∼72 °C suggesting that the traps responsible for the bands were fixed at this position irrespective of annealing temperature. These bands are at a similar position, which suggests that the traps responsible for these bands are similar. The rate of decay of the sample annealed at 600 °C was faster than that of the sample prepared at 1200 °C.     

Improvement of photoluminescence mechanism of CTA-treated Si-implanted SiO2 films by using RTA

In this paper, a shift in the photoluminescence (PL) peak from blue to near-infrared region was observed in the Si⁺-implanted 400-nm-thick SiO₂ films with the rapid thermal annealing (RTA) method only. As the Si⁺-fluence was 1×10¹⁶ ions/cm², a blue band was observed in the films after RTA at 1050 °C for 5 s in dry-N₂ atmosphere; then, the band shifted from blue to orange upon increasing the holding temperature of RTA to 1250 °C in the films after the isochronal RTA in dry N₂. Furthermore, while the fluence was increased to 3×110¹⁶ ions/cm² and the holding temperature was at the same range between 1050 and 1250 °C, the PL peak occurred between red and near-infrared regions. Although the RTA and conventional thermal annealing (CTA) methods produce a similar mechanism, the CTA method needs a much longer annealing-time and a higher Si⁺-implanted dose than the RTA method for producing the same shift and intensity of PL peak from the as-implanted sample. Therefore, the RTA method can produce the mechanism in the Si⁺-implanted sample with the PL energy between blue and near-infrared band in place of the CTA method.     

Comparing the chemical properties of evaporated and sputtered niobium films on oxidized Si(1 0 0) wafers - preparation of oxynitride films

Five hundred nanometers of niobium films have been deposited on silicon(1 0 0) wafers with 100 or 300 nm thermally grown oxide by electron beam evaporation and DC magnetron sputtering. SEM and AFM investigations revealed smaller crystallites and rougher surfaces for the evaporated films. The differences in film morphology resulted in lower reflection intensities in XRD for the as-deposited evaporated films. In order to investigate the influence of the structural properties on their chemical reactivities, in a first set of experiments the films were nitrided with molecular nitrogen by rapid thermal processing (RTP) at varying temperatures. In another set of experiments after nitridation in nitrogen at 1000 °C an oxidation step in molecular oxygen at varying temperatures followed. The films showed different reactivities, leading to different rates of nitridation and oxidation. Sputtered films were less reactive than the evaporated films, deduced from the sequence of reaction products dependent on reaction temperature. XRD data indicated that oxynitrides have formed. Elemental depth profiles were measured by secondary ion mass spectrometry (SIMS).     

Effect of PMMA on crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate) blend prepared in semi-dilute solutions

Films of poly(vinylidene fluoride) (PVDF)/poly(methyl methacrylate) (PMMA) blend were derived from a special procedure of casting semi-dilute solutions. Hydrophilic character and crystallization of PVDF were optimized by variation of PMMA concentration in PVDF/PMMA blends. It was found that a PVDF/PMMA blend containing 70 wt% PMMA has a good performance for the potential application of hydrophilic membranes via thermally induced phase separation. The films presented β crystalline phase regardless of PMMA content existed in the blends. Thermal analysis of the blends showed a promotion of crystallization of PVDF with small addition of PMMA which induced larger lamellar thickness of PVDF, leading to the largest spherulitic crystal of PVDF (10 wt% PMMA) is about 8 μm. SEM micrographs illustrated no phase separation occurred in blends, due to the high compatibility between PVDF and PMMA.     

The effect of incident angle on the C60 bombardment of molecular solids

The effect of incident angle on the quality of SIMS molecular depth profiling using C₆₀⁺ was investigated. Cholesterol films of ∼300 nm thickness on Si were employed as a model and were eroded using 40 keV C₆₀⁺ at an incident angle of 40° and 73° with respect to the surface normal. The erosion process was characterized by determining at each angle the relative amount of chemical damage, the total sputtering yield of cholesterol molecules, and the interface width between the film and the Si substrate. The results show that there is less molecule damage at an angle of incidence of 73° and that the total sputtering yield is largest at an angle of incidence of 40°. The measurements suggest reduced damage is not necessarily dependent upon enhanced yields and that depositing the incident energy nearer the surface by using glancing angles is most important. The interface width parameter supports this idea by indicating that at the 73° incident angle, C₆₀⁺ produces a smaller altered layer depth. Overall, the results show that 73° incidence is the better angle for molecular depth profiling using 40 keV C₆₀⁺.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Effect of oxidation temperature on microstructure, mechanical behaviors and surface morphology of nanocomposite Ti-Cx-Ny thin films

Two nanocomposite Ti-C_x-N_y thin films, TiC_0.95N_0.60 and TiC_2.35N_0.68, as well as one pure TiN, were deposited at 500 °C on Si(1 0 0) substrate by reactive unbalanced dc-magnetron sputtering. Oxidation experiments of these films were carried out in air at fixed temperatures in a regime of 250-600 °C with an interval of 50 °C. As-deposited and oxidized films were characterized and analyzed using X-ray diffraction (XRD), microindentation, Newton's ring methods and atomic force microscopy (AFM). It was found that the starting oxidation temperature of nanocomposite Ti-C_x-N_y thin films was 300 °C irrespective of the carbon content; however their oxidation rate strongly depended on their carbon content. Higher carbon content caused more serious oxidation. After oxidation, the film hardness value remained up to the starting oxidation temperature, followed by fast decrease with increasing heating temperature. The residual compressive stress did not show a similar trend with the hardness. Its value was first increased with increase of heating temperature, and got its maximum at the starting oxidation temperature. A decrease in residual stress was followed when heating temperature was further increased. The film surface roughness value was slightly increased with heating temperature till the starting oxidation temperature, a great decrease in surface roughness was followed with further increase of heating temperature.