Raman spectroscopic and photoluminescence study of single-crystalline SnO2 nanowires

Single-crystalline SnO₂ nanowires with sizes of 4-14 nm in diameter and 100-500 nm in length were produced in a molten salt approach by using hydrothermal synthesized precursor. Structural characters of the nanowires were examined by X-ray diffraction and high-resolution electron transmission microscopy. Raman, photoluminescence and X-ray photoelectron spectra of the samples were examined under heat treatments. Three new Raman modes at 691, 514 and 358 cm⁻¹ were recorded and assigned. The former two are attributed to activation of original Raman-forbidden A_2uLO mode and the third is attributed to defects in small-sized nanowires. A strong photoluminescence is observed at about 600 nm, the temperature effects is examined and the origin of the PL process is discussed via X-ray photoelectron spectra.     

Cr-doping induced ferromagnetic behavior in antiferromagnetic EuTiO3 nanoparticles

We have synthesized a series of high quality EuTi_1−xCr_xO₃ (x = 0.0, 0.02, and 0.04) nanoparticles by simple sol-gel technique. The averaged grain size of these obtained nanoparticles displays no obvious change with Cr-doping and is about 100 nm. The structural and magnetic properties of EuTi_1−xCr_xO₃ (x = 0.0, 0.02, and 0.04) samples were detailedly investigated. It is found that the G-antiferromagnetic (G-AFM) ordering of pure EuTiO₃ can be significantly modified with slight Cr-doping, and finally the ferromagnetic behavior is enhanced for EuTi_1−xCr_xO₃ system with Cr-doping.     

Adsorption performance and mechanism of 2,4,6-trinitrotoluene on a novel adsorption material polyvinylbenzyl acid/SiO2

Polyvinylbenzene (PVB, namely polystyrene, PSt) was grafted on the surface of silica gel particles by “grafting from” in solution polymerization system, and grafting particles PVB/SiO₂ were obtained. The chloromethylation reaction of the grafted polyvinylbenzene was performed using a novel chloromethylation reagent, 1,4-bis (chloromethyoxy) butane that is un-carcinogenic, and grafting particles CMPVB/SiO₂ were obtained. Subsequently, chloromethyl groups on grafting particles CMPVB/SiO₂ were hydrolyzed and oxidized, and finally adsorption material polyvinylbenzyl acid/SiO₂ (PVBA/SiO₂) was prepared. The adsorption performances and mechanism of 2,4,6-trinitrotoluene (TNT) on PVBA/SiO₂ were investigated through static methods. The experimental results showed that PVBA/SiO₂ possessed strong adsorption ability for TNT with adsorption amount of 26.84 mg g⁻¹. The empirical Freundlich isotherm was also found to agree well with the equilibrium adsorption data. In addition, pH was found to have great influence on the adsorption amount. Finally, PVBA/SiO₂ was observed to possess excellent reusability as well.     

Growth of high-density Ru- and RuO2-composite nanodots on atomic-layer-deposited Al2O3 film

Growth of Ru- and RuO₂-composite (ROC) nanodots on atomic-layer-deposited Al₂O₃ film has been studied for the first time using ion-beam sputtering followed by post-deposition annealing (PDA). X-ray photoelectron spectroscopy analyses reveal that RuO₂ and Ru co-exist before annealing, and around 10% RuO₂ is reduced to metallic Ru after PDA at 900 °C for 15 s. Scanning electron microscopy measurements show that well-defined spherical ROC nanodots are not formed till the PDA temperature is raised to 900 °C. The mean diameter of the nanodots enlarges with increasing PDA temperature whereas the nanodot density decreases, which is attributed to coalescence process between adjacent nanodots. It is further illustrated that the resulting nanodot size and density are weakly dependent on the annealing time, but are markedly influenced by the decomposition of RuO₂. In this article, the ROC nanodots with a high density of 1.6 × 10¹¹ cm⁻², a mean diameter of 20 nm with a standard deviation of 3.0 nm have been achieved for the PDA at 900 °C for 15 s, which is promising for flash memory application.     

Photo-catalytic H2 evolution over a series of Keggin-structure heteropoly blue sensitized Pt/TiO2 under visible light irradiation

We report the visible light-induced hydrogen generation over a series of Keggin-structure heteropoly blue (HPB) anions (PW₁₂O₄₀³⁻, phosphotungstic blue (PTB), GeW₁₂O₄₀⁴⁻ (GTB), SiW₁₂O₄₀⁴⁻ (STB), BW₁₂O₄₀⁵⁻ (BTB)) sensitized Pt/TiO₂ photo-catalysts. The sensitization of TiO₂ by HPB was certified using photo-electrochemical measurements and UV-vis absorption spectra. PTB showed the most pronounced sensitization effect for TiO₂ in those HPB anions and Pt/TiO₂-PTB showed the highest hydrogen generation activity. The sensitization of TiO₂ was significantly dependent on the reduction potential of HPA, which was determined by the kind of central atom in HPA.     

Surface characterization of the Zn-Ni-Al2O3 nanocomposite coating fabricated under ultrasound condition

Zn-Ni-Al₂O₃ nanocomposite coating, which was fabricated by eletrodeposition technique with the aid of ultrasound, was investigated by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis and X-ray photoelectron spectroscopy (XPS). The results reveal that 7.2 wt.% nano-alumina particles uniformly dispersed in the matrix of the composite coating. The XPS analyses demonstrate that the outermost layer of Zn-Ni-Al₂O₃ coating was composed of nano-alumina and Zn(OH)₂, while the transition layer between the outermost layer and the Zn-Ni matrix consisted of nano-alumina, metallic Zn, ZnO and metallic Ni. In order to investigate the influences of ultrasonic agitation and the incorporation of nano-alumina on the composition and surface structure of Zn-Ni matrix, the comparison studies of Zn-Ni-Al₂O₃ nanocomposite coating with Zn-Ni coatings fabricated with and without ultrasound were conducted. The results indicate that ultrasonic agitation resulted in a decrease of Ni content in the Zn-Ni matrix and an increase of the thickness of surface oxide layer; while the incorporation of nano-α-Al₂O₃ increased the Ni content in the Zn-Ni matrix.     

Characterization and adsorptive application of ordered mesoporous silicas

The adsorption behaviour of the n-octane/ethanol binary liquid mixture has been studied on ordered mesoporous silica materials. Adsorption excesses on SBA-15, SBA-16 and MCM-48 solids are measured and described by mathematical functions. The experimental adsorption excess isotherms are presented and discussed. The mesoporous silicas used for liquid-adsorption experiments are characterized by nitrogen adsorption before and after liquid adsorption by the powder X-ray diffraction (XRD) and by the sample controlled thermal analysis (SCTA).     

Effect of surface fluorination on the photocatalytic and photo-induced hydrophilic properties of porous TiO2 films

Porous surface-fluorinated TiO₂ (F-TiO₂) films were prepared through PEG modified sol-gel method and surface fluorination. The as-prepared films were characterized with XRD, FTIR, AFM, XPS and UV-vis DRS. The effects of surface fluorination on the photocatalytic activity and hydrophilicity of porous TiO₂ film were studied by photocatalytic degradation of rhodamine B (RhB) as well as water contact angle (CA) on porous TiO₂ film. The results showed that the surface fluorination increased the adsorption of RhB on the porous TiO₂ film and enhanced the photocatalytic degradation of RhB. The concentration and pH of NaF solutions affected much the photocatalytic activity of porous TiO₂ film. Porous F-TiO₂ film prepared in 40 mM NaF solution at pH 4.0 showed the highest photocatalytic activity. Because of its porous structure, the porous F-TiO₂ film had original water CA of 22.7°, which is much smaller than that of normal F-TiO₂ film. Under UV light irradiation, the water CA of porous F-TiO₂ film decreased to 5.1° in 90 min.     

Fabrication of magnetic composite nanofibers of poly(ε-caprolactone) with FePt nanoparticles by coaxial electrospinning

In this article, composite nanofibers of poly(ε-caprolactone) (PCL) with iron–platinum (FePt) nanoparticles were successfully fabricated via coaxial electrospinning. The structure and morphology of FePt/PCL composite nanofibers were observed using transmission electron microscope and scanning electron microscope, respectively. The magnetic behavior of FePt/PCL composite nanofibers was investigated by alternating gradient magnetometer at room temperature.     

Low-temperature preparation of F-doped TiO2 film and its photocatalytic activity under solar light

A novel and simple method for preparing F-doped anatase TiO₂ (defined as FTO) film with high photocatalytic activity was developed using titanium-n-butoxide and NH₄F as TiO₂ and fluorine precursors under mild condition, i.e. low temperature (lower than 373 K) and ambient pressure. The prepared samples were characterized by XRD, SEM, X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectrum (DRS), photoluminescence spectrum (PL) and TG-DSC analysis. The photocatalytic activity was evaluated by decomposing X-3B under artificial solar light. The results showed that the crystallinity of TiO₂ was improved by F-doping. F⁻ ions can prevent the grain growth, and the transformation of anatase to rutile phase was also inhibited. The doped fluorine atoms existed in two chemical forms, and the ones incorporated into TiO₂ lattice might take a positive role in photocatalysis. Compared with surface fluorination samples, FTO film exhibited better photocatalytic activity. The high photocatalytic activity of FTO may due to extrinsic absorption through the creation of oxygen vacancies rather than the excitation of the intrinsic absorption band of bulk TiO₂. Furthermore, the FTO can be recycled with little photocatalytic activity depression. Without any further treatment besides rinsing, after 6 recycle utilization, the photocatalytic activity of FTO film was still higher than 79%.     

Photoluminescence from amorphous silica nanowires synthesized using TiN/Ni/SiO2/Si and TiN/Ni/Si substrates

Photoluminescence characteristics of amorphous silica nanowires (a-SiONWs) grown on TiN/Ni/Si and TiN/Ni/SiO₂ substrates have been studied. A-SiONWs grown on TiN/Ni/Si substrates show a Si-rich composition compared to those grown from TiN/Ni/SiO₂/Si. The emission characteristics of the nanowires were found to depend on the type of substrate. By annealing the a-SiONWs grown on TiN/Ni/Si in air, emission bands shift from blue to green bands. It is likely that silicon to oxygen ratio is an important factor in deciding the types of defects and emission bands of amorphous silica nanowires.     

Low-temperature transport properties of individual SnO2 nanowires

Stannic oxide (SnO₂) nanowires have been prepared by Chemical vapor deposition (CVD). The low-temperature transport properties of a single SnO₂ nanowire have been studied. It is found that the transport of the electrons in the nanowires is dominated by the Efros-Shklovskii variable-range hopping (ES-VRH) process due to the enhanced Coulomb interaction in this semiconducting nanowire. The temperature dependence of the resistance follows the relation lnR∼T^−1/2. On the I-V and dI/dV curves of the nanowire a Coulomb gap-like structure at low temperatures appears.     

Sticking coefficient of nitrogen on solid N2 at low temperatures

The sticking coefficient of nitrogen gas on a thick solid nitrogen film on a copper cold finger was studied at low temperature. For surface temperatures of about 12 K the sticking coefficient is measured to be 99.0 ± 0.6%. Our result implies that it will be possible to make a intense and high brightness slow positron source starting from a small diameter deposit of the gaseous positron emitter ¹³N₂ produced in the reaction ¹²C(d,n)¹³N.     

Characterization of nanoporous carbons by combining CO2 and H2 sorption data with the Monte Carlo simulations

The Monte Carlo method in its grand ensemble variant (GCMC) is used in combination with experimental data in order to characterize microporous carbons and obtain the optimal pore size distribution (PSD). In particular, the method is applied in the case of AX-21 carbon. Adsorption isotherms of CO₂ (253 and 298 K) and H₂ (77 K) up to 20 bar have been measured, while the computed isotherms resulted from the GCMC simulations for several pore widths up to 3.0 nm. For the case of H₂ at 77 K quantum corrections were introduced with the application of the Feynman-Hibbs (FH) effective potential. The adsorption isotherms were used either individually or in a combined manner in order to deduce PSDs and their reliability was examined by the ability to predict the experimental adsorption isotherms. The combined approach was found to be capable of reproducing more accurately all the available experimental isotherms.     

Photoluminescence of Si from Si nanocrystal-doped SiO2/Si multilayered sample

A multilayered Si nanocrystal-doped SiO₂/Si (or Si-nc:SiO₂/Si) sample structure is studied to acquire strong photoluminescence (PL) emission of Si via modulating excess Si concentration. The Si-nc:SiO₂ results from SiO thin film after thermal annealing. The total thickness of SiO layer remains 150 nm, and is partitioned equally into a number of sublayers (N = 3, 5, 10, or 30) by Si interlayers. For each N-layered sample, a maximal PL intensity of Si can be obtained via optimizing the thickness of Si interlayer (or d_Si). This maximal PL intensity varies with N, but the ratio of Si to O is nearly a constant. The brightest sample is found to be that of N = 10 and d_Si = 1 nm, whose PL intensity is ∼5 times that of N = 1 without additional Si doping, and ∼2.5 times that of Si-nc:SiO₂ prepared by co-evaporating of SiO and Si at the same optimized ratio of Si to O. Discussions are made based on PL, TEM, EDX and reflectance measurements.     

Large-scale synthesis of rutile SnO2 nanorods

A high yield of tin oxide (SnO₂) nanorods was obtained via annealing a nanoscale precursor in the molten salt flux and surfactant. X-ray diffraction, transmission electron microscopy, high-resolution transmission electron microscopy, selected area electron diffraction and infrared spectroscopy showed that the nanorods are composed of SnO₂ with rutile structure. The surfactant and temperature have a profound influence on the production of SnO₂ nanorods.     

Synthesis of PEO/4Hb-TaS2 layered nanocomposite

Single-phase layered nanocomposite containing 4Hb-TaS₂ and poly(ethylene oxide) [PEO] has been first synthesized by using the exfoliation-adsorption technique. It has been characterized by powder X-ray diffraction (XRD) and electrical dc resistivity measurements. As the product exhibited lattice expansions along the stacking direction, PEO was intercalated into 4Hb-TaS₂ galleries.     

One-dimensional structures of Bi2O3 synthesized via metalorganic chemical vapor deposition process

We have demonstrated the synthesis of one-dimensional (1D) structures of bismuth oxide (Bi₂O₃) by a reaction of a trimethylbismuth (TMBi) and oxygen (O₂) mixture at 450 °C. Scanning electron microscopy showed that the product consisted of 1D materials with width or diameters less than 1 μm and lengths up to several tens of micrometers. The X-ray energy dispersive spectroscopy revealed that the materials contained elements of Bi and O. The results of X-ray diffraction and selected area electron diffraction pattern indicated that the obtained Bi₂O₃ were crystalline with monoclinic structure.     

Preparation of activated carbon from cherry stones by chemical activation with ZnCl2

Cherry stones (CS), an industrial product generated abundantly in the Valle del Jerte (Cáceres province, Spain), were used as precursor in the preparation of activated carbon by chemical activation with ZnCl₂. The influence of process variables such as the carbonisation temperature and the ZnCl₂:CS ratio (impregnation ratio) on textural and chemical-surface properties of the products obtained was studied. Such products were characterised texturally by adsorption of N₂ at −196 °C, mercury porosimetry and density measurements. Information on the surface functional groups and structures of the carbons was provided by FT-IR spectroscopy. Activated carbon with a high development of surface area and porosity is prepared. When using the 4:1 impregnation ratio, the specific surface area (BET) of the resultant carbon is as high as 1971 m² g⁻¹. The effect of the increase in the impregnation ratio on the porous structure of activated carbon is stronger than that of the rise in the carbonisation temperature, whereas the opposite applies to the effect on the surface functional groups and structures.     

Enhanced activity of mesoporous Nb2O5 for photocatalytic hydrogen production

The mesoporous Nb₂O₅ photocatalysts were synthesized via an evaporation-induced self-assembly (EISA) method. The mesoporous structure of the as-made samples was studied by small-angle X-ray diffraction, N₂ adsorption-desorption isothermal and transmission electron microscopy. The increase of the calcination temperature during the synthesis resulted in enhanced crystallization, but decreased mesoporosity of the samples. The later was found to have a crucial influence on the photocatalytic activity by bringing on decreased BET surface area and especially increscent pore wall thickness. The advantage of the mesoporous Nb₂O₅ was also proved by performing 20 times higher photocatalytic activity than a bulk Nb₂O₅ without any porosity. A model was given to describe the effect of mesoporosity on the transportation and recombination of carriers.