钒酸铟分级结构微米花和纳米线的水热合成和可见光催化性能

采用水热法合成InVO₄分级结构微米花和InVO₄纳米线．FESEM结果表明, 通过控制水热反应参数可以获得不同形貌InVO₄晶体．利用可见光(λ>420 nm)照射下的罗丹明B降解实验评价了InVO₄样品的光催化性能．结果表明,InVO₄的光催化活性比商用P25 TiO₂高得多,其中花状InVO₄纳米结构光催化效率最高,经可见光照射40 min,罗丹明     

Fabrication and characterization of electrospun orthorhombic InVO4 nanofibers

The novel orthorhombic InVO₄ nanofibers have been successfully synthesized by annealing electrospun precursor fibers. Citric acid was used as a ligand for it could react with metal salts to get a transparent homogeneous precursor solution and homogeneous precursor sol for electrospining. Polyvinyl pyrrolidone (PVP, K-30) was used as a binder and a structure guide reagent because it was one kind of water-soluble polymers. It is easy to gain one-dimensional materials while the viscosity of the citrate/PVP sol was suitable. The structure, morphology and photocatalytic properties of the nanofibers were characterized by X-ray diffraction (XRD), thermogravimetry analysis (TGA), scanning electron microscopy (SEM) analysis, UV-vis spectrophotometer and fluorescence spectrophotometer. The nanofibers calcined at 700 °C were orthorhombic InVO₄ with a width in the range of 30-100 nm and length in micron-grade. This one-dimensional pure orthorhombic InVO₄ had the higher photocatalytic activity under visible light irradiation. The photo-degradation rate of nitrobenzene aqueous solution under visible light reached 69% after 6 h. It is obvious that the orthorhombic InVO₄ nanofibers have a potential application in wastewater-treatment.     

Synthesis, characterization and photocatalytic activities of rare earth-loaded BiVO4 catalysts

The BiVO₄-based photocatalysts loaded with rare earth (RE=Ho, Sm, Yb, Eu, Gd, Nd, Ce and La) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), diffuse reflectance spectroscopy (DRS), nitrogen adsorption for the BET specific surface area and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the samples were evaluated by decolorization of methylene blue (MB) under visible light irradiation. The results of XRD, SEM and XPS analysis deduced that the rare earth ions were present as RE₂O₃ in the samples. The DRS analysis showed the shift in the absorbption edge from the UV to the visible range: Ho³⁺-BiVO₄ < Sm³⁺-BiVO₄ < Yb³⁺-BiVO₄ < Eu³⁺-BiVO₄ < Gd³⁺-BiVO₄ < Nd³⁺-BiVO₄ < La³⁺-BiVO₄ < Ce³⁺-BiVO₄ < BiVO_4. Gd³⁺-BiVO₄ had the highest photocatalytic activity among all the RE³⁺-BiVO₄ catalysts. The optimal Gd content was 8 at% under visible light irradiation. This beneficial effect was attributed to the specific electron structure characteristics of gadolinium and the increasing in the separation efficiency of the electron-hole pairs. On the contrast, the other rare earth ions had the detrimental effect on the photocatalytic decolorization of MB.     

Synthesis and characterization of Ag/BiVO4 composite photocatalyst

Ag/BiVO₄ composite photocatalysts were hydrothermal synthesized and characterized by XRD, SEM, XPS and DRS techniques. Their photocatalytic activities were determined by oxidative decomposition of methyl orange in aqueous solution under visible light irradiation. It revealed that the doped Ag species greatly improved the visible light absorption abilities and morphologies of the composites, and thus lead to enhanced photocatalytic activities compared with that of the pure BiVO₄.     

Preparation of photocatalytic Fe2O3-TiO2 coatings in one step by metal organic chemical vapor deposition

There are two major difficulties in the TiO₂ liquid-solid photocatalytic system: effective immobilization of the TiO₂ particles; and improving the catalytic activity under visible light. To simultaneously solve these two problems, Fe₂O₃-TiO₂ coatings supported on activated carbon fiber (ACF), have been prepared in one step by a convenient and efficient method—metal organic chemical vapor deposition (MOCVD). XRD results revealed that Fe₂O₃-TiO₂ coatings mainly composed of anatase TiO₂, α-Fe₂O₃ phases and little Fe₂Ti₃O₉. The pore structure of ACF was preserved well after loading with Fe₂O₃-TiO₂ coatings. UV-vis diffuse reflectance spectra showed a slight shift to longer wavelengths and an enhancement of the absorption in the visible region for Fe₂O₃-TiO₂ coatings, compared to the pure TiO₂ sample. A moderate Fe₂O₃-TiO₂ loading (13.7 wt%) was beneficial to mineralizing wastewater because the intermediates could be adsorbed onto the surface of photocatalyst following decomposition. The stable performance revealed that the Fe₂O₃-TiO₂ coatings were strongly adhered to the ACF surface, and the as prepared catalysts could be reused showing potential application for wastewater treatment.     

Preparation and characterization of visible light responsive Fe2O3-TiO2 composites

In this study we present the effects of iron oxide (Fe₂O₃) on titanium dioxide (TiO₂) in synthesising visible-light reactive photocatalysts. A Fe₂O₃-TiO₂ composite photocatalyst was synthesized from Fe₂(SO₄)₃ and Ti(SO₄)₂ by a ethanol-assisted hydrothermal method. The preparation conditions were optimized through the investigation of the effects of hydrothermal temperature and time as well as molar ratio of Ti to Fe on the photocatalytic activity. The visual, physical and chemical properties of the Fe₂O₃-TiO₂ composites were investigated. The results showed that α-Fe₂O₃ and anatase TiO₂ were present in the composites. The Fe₂O₃-TiO₂ synthesized under optimum condition consisted of mesoporous structure with an average pore size of 4 nm and a surface area of 43 m²/g. Under visible and solar light irradiation, the photocatalytic activity of optimized sample was significantly higher than that of pure TiO₂. This sample led to a photodegradation efficiency of 90% and 40% of auramine under visible light and solar light, respectively.     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Preparation of visible light responsive N doped TiO2 via a reduction-nitridation procedure by nonthermal plasma treatment

A visible light responsive N-doped TiO₂ was prepared via a reduction-nitridation procedure by nonthermal plasma treatment. X-ray diffraction, N₂ adsorption, UV-vis spectroscopy, photoluminescence, and X-ray photoelectron spectroscopy were used to characterize the prepared TiO₂ samples. The plasma treatment did not change the phase composition and particle sizes of TiO₂ samples, but extended its absorption edges to the visible light region. The photocatalytic activities were tested in the degradation of an aqueous solution of a reactive dyestuff, methylene blue, under visible light. The photocatalytic activities of TiO₂ prepared by reduction-nitridation procedure were much higher than that of samples prepared by simple nitridation treatment. The enhanced activity was ascribed to the substitutional N-doping and appropriate concentration of oxygen vacancies. TOHN10 prepared by reduction-nitridation procedure exhibited excellent photocatalytic stability. A possible mechanism for the photocatalysis was proposed.     

Room temperature ferromagnetism in vacuum-annealed TiO2 thin films

Thin films of pure TiO₂ have been prepared using both spin-coating and sputter-deposition techniques on sapphire and quartz substrates. The structural characteristics of the films have been investigated in detail using Raman spectroscopy and high-resolution transmission electron microscopy (HRTEM). When annealed in vacuum, all films demonstrate room temperature ferromagnetism, while the air-annealed samples show much smaller, often negligible, magnetic moments. The magnetization of the vacuum-annealed sputtered samples depends on film thickness, with the volume magnetization decreasing monotonically with increasing thickness. Furthermore, the magnetization per unit area also decreases slightly with increasing film thickness. These results suggest that ferromagnetism in the vacuum-annealed TiO₂ films is mediated by surface defects or interfacial effects, but does not arise from stoichiometric crystalline TiO₂.     

Cu2ZnSnSe4 thin films prepared by selenization of co-electroplated Cu-Zn-Sn precursors

A novel technique for growth of high quality Cu₂ZnSnSe₄ (CZTSe) thin films is reported in our work. The CZTSe thin films were fabricated onto Mo layers by co-electroplating Cu-Zn-Sn precursors followed by annealing in the selenium vapors at the substrate temperature of 550 °C. The morphology and structure of CZTSe thin films were characterized using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD) and Raman scattering spectrum, respectively. The results revealed that the single phase was in the CZTSe thin films, and the other impurities such as ZnSe and Cu₂SnSe₃ were not existed though they were difficult to distinguish both from EDS and XRD.     

Enhanced visible light photocatalytic properties of Fe-doped TiO2 nanorod clusters and monodispersed nanoparticles

In order to get photocatalysts with desired morphologies and enhanced visible light responses, the Fe-doped TiO₂ nanorod clusters and monodispersed nanoparticles were prepared by modified hydrothermal and solvothermal method, respectively. The microstructures and morphologies of TiO₂ crystals can be controlled by restraining the hydrolytic reaction rates. The Fe-doped photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV-vis absorption spectroscopy (UV-vis), N₂ adsorption-desorption measurement (BET), and photoluminescence spectroscopy (PL). The refinements of the microstructures and morphologies result in the enhancement of the specific surface areas. The Fe³⁺-dopants in TiO₂ lattices not only lead to the significantly extending of the optical responses from UV to visible region but also diminish the recombination rates of the electrons and holes. The photocatalytic activities were evaluated by photocatalytic decomposition of formaldehyde in air under visible light illumination. Compared with P25 (TiO₂) and N-doped TiO₂ nanoparticles, the Fe-doped photocatalysts show high photocatalytic activities under visible light.     

Preparation and characterization of novel Pd/SiO2 and Ca-Pd/SiO2 egg-shell catalysts with porous hollow silica

Novel egg-shell structured monometallic Pd/SiO₂ and bimetallic Ca-Pd/SiO₂ catalysts were prepared by an impregnation method using porous hollow silica (PHS) as the support and PdCl₂ and Ca(NO₃)₂·4H₂O as the precursors. It was found from transmission electron microscope (TEM), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) that Pd was loaded on PHS with a particle size of 5-12 nm in Pd/SiO₂ samples and the Pd particle size in Ca-Pd/SiO₂ was smaller than that in Pd/SiO₂ since Ca could prevent Pd particles from aggregating. X-ray photoelectron spectroscopy (XPS) analyses exhibited that Pd 3d_5/2 binding energies of Pd/SiO₂ and Ca-Pd/SiO₂ were 0.2 and 0.9 eV lower than that of bulk Pd, respectively, as a result of the shift of the electron cloud from Pd to oxygen in Pd/SiO₂ and to both oxygen and Ca in Ca-Pd/SiO₂. The activity of Ca-Pd/SiO₂ egg-shell catalyst for CO hydrogenation and the selectivity to methanol, with a value of 36.50 mmol_CO mol⁻¹_Pd s⁻¹ and 100%, respectively, were much higher than those of the catalysts prepared with traditional silica gel as the support, owing to the porous core-shell structure of the PHS support.     

Crystallisation of TiO2 thin films induced by excimer laser irradiation

Titanium dioxide thin films have been deposited by reactive magnetron sputtering on glass substrate and subsequently irradiated by UV radiation using a KrF excimer laser. In this work, we have study the influence of the laser fluence (F) ranging between 0.05 and 0.40 mJ/cm² on the constitution and microstructure of the deposited films. Irradiated thin films are characterized by profilometry, scanning electron microscopy and X-ray diffraction. As deposited films are amorphous, while irradiated films present an anatase structure. The crystallinity of the films strongly varies as a function of F with maximum for F = 0.125 J/cm². In addition to the modification of their constitution, the irradiated areas present a strongly modified microstructure with appearance of nanoscale features. The physico-chemical mechanisms of these structural modifications are discussed based on the theory of nucleation.     

Preparation, structures and photoluminescent enhancement of CdWO4-TiO2 composite nanofilms

For the first time, Cadmium tungstate (CdWO₄)-TiO₂ composite nanofilms on a glass substrate were prepared by means of the dip-coating technique, in which collodion was used as a dispersant and film-forming agent. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermo gravimetric and thermal analyses (TG/DTA), FTIR and photoluminescence (PL) methods, respectively. SEM and XRD characterization of these films indicated that CdWO₄ particles crystallized in a monoclinic wolframite-type structure whereas TiO₂ particles were Anatase phase; and both of them were well distributed in the nanofilms. FTIR spectra proved the presence of CdWO₄ on the nanofilms. Photoluminescent results showed that the emitting peak of CdWO₄ films blue shifted slightly relative to that of CdWO₄ crystal. Moreover, the PL intensity of CdWO₄-TiO₂ composite nanofilm was much higher than that of CdWO₄ nanofilm. We ascribed that the introduction of TiO₂ should be responsible for the PL enhancement.     

MOCVD of zirconium oxide thin films: Synthesis and characterization

The synthesis of thin films of zirconia often produces tetragonal or cubic phases, which are stable at high temperatures, but that can be transformed into the monoclinic form by cooling. In the present study, we report the deposition of thin zirconium dioxide films by metalorganic chemical vapor deposition using zirconium (IV)-acetylacetonate as precursor. Colorless, porous, homogeneous and well adherent ZrO₂ thin films in the cubic phase were obtained within the temperature range going from 873 to 973 K. The deposits presented a preferential orientation towards the (1 1 1) and (2 2 0) planes as the substrate temperature was increased, and a crystal size ranging between 20 and 25 nm. The kinetics is believed to result from film growth involving the deposition and aggregation of nanosized primary particles produced during the CVD process. A mismatch between the experimental results obtained here and the thermodynamic prediction was found, which can be associated with the intrinsic nature of the nanostructured materials, which present a high density of interfaces.     

溶胶-凝胶ZrO2-TiO2高折射率光学膜层的抗激光损伤性能研究

采用溶胶-凝胶方法制备了ZrO₂-TiO₂(Ti含量为0—100mol%)高折射率光学薄膜. 借助激光动态光散射技术研究溶胶微结构. 采用傅里叶变换红外光谱、原子力显微镜、薄膜光学常数分析仪、漫反射吸收光谱及强激光辐照实验，对膜层的结构、光学性能及抗激光损伤性能进行了系统表征. 结果显示，溶胶-凝胶工艺可以在部分牺牲折射率的情况下，使膜层的抗激光损伤性能得到大幅度提升. 随Ti含量从0mol%增加至100mol%，膜层的平均损伤阈值呈下降趋势，当Ti含量从0mol%增加至60mol%时，平均损伤阈值从57.1J/cm²下降到21.1J/cm²(辐照激光波长为1053nm，脉冲宽度为10ns，“R/1”测试模式)，当Ti含量从60mol%增加至100mol%时，平均损伤阈值变化很小. 综合溶胶微结构、膜层光学性能和损伤实验结果可以推断，强激光诱导多光子吸收是引起膜层损伤的主要原因. 不同配比的复合膜之间光学带隙的显著差异导致相同辐照激光情况下多光子吸收的概率发生变化，从而导致损伤阈值的规律性变化. 关键词： 2-TiO₂薄膜')" href="#">ZrO₂-TiO₂薄膜 溶胶-凝胶 激光诱导损伤 光学带隙     

三元异质结构Ag-Bi2MoO6/BiPO4光催化剂高效降解苯酚红

多组分复合体系有利于电荷的有效分离,减少电子空穴对的复合几率。通过低温液相法首次合成Ag-Bi₂MoO₆/BiPO₄三元异质结构光催化剂。利用XRD、SEM、EDX及XPS等技术对样品进行了表征。结果表明,Ag纳米粒子光照积累在Bi₂MoO₆/BiPO₄的表面,通过表面等离子共振增加对可见光的吸收,同时作为电子受体促进了光生电子的转移。Ag、BiPO₄和Bi₂MoO₆形成三元异质结构有效地抑制了光生电子空穴对的复合。Ag-Bi₂MoO₆/BiPO₄表现出优异的光催化性能,其光催化活性较BiPO₄、Bi₂MoO₆和Bi₂MoO₆/BiPO₄样品有较大提高。并且对Ag-Bi₂MoO₆/BiPO₄三元异质结构的光催化机制进行了讨论。光催化过程中反应活性物种捕获实验结果表明h⁺和O₂^·-是主要的活性基团.     

Cathode luminescence characteristics of ZnGa2O4 phosphor thin films with the doped activator

The zincgallate (ZnGa₂O₄) phosphor thin film was grown using RF magnetron sputtering system at various process parameters. A ZnGa₂O₄ phosphor thin film was deposited on Si(1 0 0) substrate and annealed by a rapid thermal processor (RTP). The X-ray diffractometer (XRD) patterns indicate that the Mn-doped ZnGa₂O₄ phosphor thin film shows a (3 1 1) main peak and a spinel phase. A ZnGa₂O₄ phosphor thin film has better crystallization due to increased substrate, annealing temperature and deposition time. Also the ZnGa₂O₄:Mn phosphor thin film shows green emission (510 nm, ⁴T₁→⁶A₁), and the ZnGa₂O₄:Cr phosphor thin film shows red emission (705 nm, ⁴A₂→⁴T₂).     

Chemical synthesis of nanocrystalline SnO2 thin films for supercapacitor application

Nanocrystalline SnO₂ thin films were deposited by simple and inexpensive chemical route. The films were characterized for their structural, morphological, wettability and electrochemical properties using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy techniques (SEM), transmission electron microscopy (TEM), contact angle measurement, and cyclic voltammetry techniques. The XRD study revealed the deposited films were nanocrystalline with tetragonal rutile structure of SnO₂. The FT-IR studies confirmed the formation of SnO₂ with the characteristic vibrational mode of Sn-O. The SEM studies showed formation of loosely connected agglomerates with average size of 5-10 nm as observed from TEM studies. The surface wettability showed the hydrophilic nature of SnO₂ thin film (water contact angle 9°). The SnO₂ showed a maximum specific capacitance of 66 F g⁻¹ in 0.5 Na₂SO₄ electrolyte at 10 mV s⁻¹ scan rate.     

Preparation and characterization of iodine-doped mesoporous TiO2 by hydrothermal method

Iodine-doped mesoporous TiO₂ (I/TiO₂) was prepared by hydrothermal method, using tetrabutyl titanate as precursor, potassium iodate as iodine sources. The as-prepared I/TiO₂ catalysts were characterized by UV-vis, XRD, TEM, BET, TG/DTA, XPS and photoluminescence (PL) spectroscopy. Production of OH radicals on the I/TiO₂ surface was detected by the PL technique using terephthalic acid as a probe molecule. The effects of hydrothermal reaction temperature, calcination temperature and iodine doping content on the structure and properties of the catalysts were investigated. The results showed that iodine-doped TiO₂ calcinated at 300 °C have good anatase crystal. The optimal hydrothermal conditions have been determined to be that reaction temperature 120 °C, calcinated temperature 300 °C and added 1.16 mmol iodine dopants. The average particle size of I/TiO₂ synthesized under optimal condition (I-3 sample) is about 3.9 nm. The I-3 photocatalyst contains 100% anatase crystalline phase of TiO₂. BET specific surface area of I-3 sample is184.8 m² g⁻¹ and is 3.67 times that of pure TiO₂ (50.37 m² g⁻¹). Iodine in I/TiO₂ catalyst mainly exists in the form of I₂, and photoactivity of I/TiO₂ catalyst in visible light comes from photosensitize of I₂. I/TiO₂ catalysis shows very high efficiency for the degradation of phenol under visible light.