Reactive ion scattering study of physisorbed adsorbates: experiment and theory

We have studied reactive ion scattering (RIS) of hyperthermal (1–100 eV) Cs⁺ projectiles from physisorbed surfaces. RIS experiments from physisorbed water on Pt(1 1 1) reveal scattering products of Cs(H₂O)_n⁺ (n=1–3) cluster ions. The yields for RIS products are extremely high compared to those with chemisorbed species. Classical molecular dynamics simulations provide a new mechanism that explains the enhanced RIS yields with physisorbed species. Slow Cs⁺ projectiles pick up physisorbed molecules via an ion–surface abstraction reaction, preferably without direct collisions between projectile and adsorbate. This RIS process is very efficient and mechanistically different from the RIS process responsible for chemisorbed species that occurs through direct collision-induced desorption.     

Polyethylene terephthalate (PET) bulk film analysis using C60, Au3, and Au primary ion beams

The damage characteristics of polyethylene terephthalate (PET) have been studied under bombardment by C₆₀⁺, Au₃⁺ and Au⁺ primary ions. The observed damage cross-sections for the three ion beams are not dramatically different. The secondary ion yields however were significantly enhanced by the polyatomic primary ions where the secondary ion yield of the [M + H]⁺ is on average 5× higher for C₆₀⁺ than Au₃⁺ and 8× higher for Au₃⁺ than Au⁺. Damage accumulates under Au⁺ and Au₃⁺ bombardment while C₆₀⁺ bombardment shows a lack of damage accumulation throughout the depth profile of the PET thick film up to an ion dose of ∼1 × 10¹⁵ ions cm⁻². These properties of C₆₀⁺ bombardment suggest that the primary ion will be a useful molecular depth profiling tool.     

Evaluation of secondary ion yield enhancement from polymer material by using TOF-SIMS equipped with a gold cluster ion source

We investigated the enhancement of the secondary ion intensity in the TOF-SIMS spectra obtained by Au⁺ and Au₃⁺ bombardment in comparison with Ga⁺ excitation using polymer samples with different molecular weight distributions. Since the polymer samples used in this experiment have a wide molecular weight distribution, the advantages of the gold cluster primary ion source over monoatomic ion could accurately be evaluated. It was observed that the degree of fragmentation decreased by the usage of cluster primary ion beam compared with monoatomic ion beam, which was observed as a shift of the intensity distribution in the spectra. It was also found out that the mass effect of Au⁺ and Ga⁺ as monoatomic primary ion, resulted in about 10-60 times of enhancement for both samples with different molecular distributions. On the other hand, the Au₃⁺ bombardment caused intensity enhancement about 100-2600 compared with Ga⁺ bombardment, depending on the mass range of the detected secondary ion species. The cluster primary ion effect of Au₃⁺, compared with Au⁺, therefore, was estimated to be about 10-45.     

High-intensity Si cluster ion emission from a silicon target bombarded with large Ar cluster ions

Secondary ions emitted from Si targets were measured with a quadrupole mass spectrometer under large Ar cluster and monomer ion bombardment. Incident ion beams with energies from 7.5 to 25 keV were used and the mean size of the Ar cluster ion was about 1000 atoms/cluster. Si_n⁺ ions with n values up to n = 8 were detected under Ar cluster ion bombardment, whereas Si cluster ions were scarcely detected under Ar monomer ion bombardment. These cluster ion yields showed the power law dependence on the cluster size.     

Hydration-induced conformational changes in protonated 2,4-pentanedione in the gas phase

Starting with H⁺[CH₃C(O)CH₂C(O)CH₃] (denoted H⁺PD), the protonated diketone-water clusters H⁺PD(H₂O) _n (n = 1–3) have been characterized by density functional theory calculations in combination with vibrational predissociation spectroscopy to explore the conformational changes of a protonated bifunctional ion solvated by water in the gas phase. Theoretical calculations for H⁺PD revealed that the ion contains an intramolecular hydrogen bond (IHB), with two oxygen atoms bridged by the extra proton in an O—H⁺ … O form. Attachment of one water molecule to it readily ruptures this IHB, replacing the H⁺ by the H₃O⁺ moiety. Further replacement of the IHB by two water molecules occurs at n = 2 and the ?C(O)CH₂C(O)- chain is fully opened (or unfolded) after transfer of the extra proton to the water trimer at n = 3. To verify the computational findings, infrared spectroscopic measurements were performed using a vibrational predissociation ion trap spectrometer to identify cluster isomers from the signatures of hydrogen bonded and non-hydrogen bonded OH stretching spectra of H⁺PD(H₂O)_2,3 produced in a corona discharge supersonic expansion. Besides open form isomers, evidence for the formation of water-bridged structures has been found for H⁺PD(H₂O)₃ at an estimated temperature of 200 K. A detailed illustration of the unfolding steps as well as the energy profiles for the evolution of a two-water bridge isomer from the protonated H⁺PD monomer are analysed pictorially (including both stable intermediates and transition states) in the present investigation.     

Analysis of TOF-SIMS spectra from fullerene compounds

We analyzed TOF-SIMS spectra obtained from three different size of fullerenes (C₆₀, C₇₀ and C₈₄) by using Ga⁺, Au⁺ and Au₃⁺ primary ion beams and investigated the fragmentation patterns, the enhancement of secondary ion yields and the restraint of fragmentation by using cluster primary ion beams compared with monoatomic primary ion beams. In the TOS-SIMS spectra from C₇₀ and C₈₄, it was found that a fragment ion, identified as C₆₀⁺ (m/z = 720), showed a relatively high intensity compared with that of other fragment ions related to C₂ depletion. It was also found that the Au₃⁺ bombardment caused intensity enhancement of intact molecules (C₆₀⁺, C₇₀⁺ and C₈₄⁺) and restrained the fragmentation due to C₂ depletion.     

Anomalous enhancement of negative sputtered ion emission by oxygen

Enhancement of negative sputtered ion yields by oxygen (either O⁺₂ bombardment or O₂ gas with Ar⁺ bombardment) is demonstrated for Si^?, As^?, P^?, Ga^?, Cu^? and Au^?, sputtered from a variety of matrices. Because oxygen also enhances positive ion yields of the same species, this effect cannot be simply explained on the basis of existing sputtered ion emission models. To rationalize these phenomena, a surface polarization model is developed which invokes localized electron emissive or electron retentive sites associated with differently oriented surface dipoles in the oxygenated surface. Such sites are considered to dominate the emission of negative and positive ions respectively. The model is shown to correctly predict that Au⁺ and Au^? ion yields are much more strongly enhanced by oxygen in dilute Au-Al alloys than in pure gold.     

Electron stimulated desorption of H3O from 316L stainless steel

Surface ions generated by electron stimulated desorption from mass spectrometer ion source grids are frequently observed, but often misidentified. For example, in the case of mass 19, the source is often assumed to be surface fluorine, but since the metal oxide on grid surfaces has been shown to form water and hydroxides, a more compelling case can be made for the formation of hydronium. Further, fluorine is strongly electronegative, so it is rarely generated as a positive ion. A commonly used metal for ion source grids is 316L stainless steel. Thermal vacuum processing by bakeout or radiation heating from the filament typically alters the surface composition to predominantly Cr₂O₃. X-ray photoelectron spectral shoulders on the O 1s and Cr 2p_3/2 peaks can be attributed to adsorbed water and hydroxides, the intensity of which can be substantially increased by hydrogen dosing. On the other hand, the sub-peak intensities are substantially reduced by heating and/or by electron bombardment. Electron bombardment diode measurements show an initial work function increase corresponding to predominant hydrogen desorption (H₂) and a subsequent work function decrease corresponding to predominant oxygen desorption (CO). The fraction of hydroxide concentration on the surface was determined from X-ray photoelectron spectroscopy and from the deconvolution of temperature desorption spectra. Electron stimulated desorption yields from the surface show unambiguous H₃O⁺ peaks that can be significantly increased by hydrogen dosing. Time of flight secondary ion mass spectrometry sputter yields show small signals of H₃O⁺, as well as its constituents (H⁺, O⁺ and OH⁺) and a small amount of fluorine as F⁻, but no F⁺ or F⁺ complexes (HF⁺, etc.). An electron stimulated desorption cross-section of σ⁺ ∼ 1.4 × 10⁻²⁰ cm² was determined for H₃O⁺ from 316L stainless steel for hydrogen residing in surface chromium hydroxide.     

Molecular ion emission from single large cluster impacts

We investigated the emission of the secondary ions stimulated by single impacts of 136 keV Au₄₀₀⁴⁺ projectiles. The study was carried out on targets of glycine, phenylalanine, and C₆₀. In addition, a target of C₆₀ was examined with 18 keV C₆₀⁺ projectiles. The experiments were performed in the event-by-event bombardment/detection mode. The secondary ions were identified with linear time-of-flight mass spectrometer equipped with an 8-anode detector. The Au₄₀₀⁴⁺ projectile induces abundant multi-ion emission, for instance the average number of detected ions (atomic, fragment, molecular and cluster ions) emitted per event from glycine target is 12.5. The glycine intact molecular ion (Gly⁻) yield is 1.14. The bombardment of a C₆₀ target results in the efficient emission of multiple intact C₆₀⁻ (total yield is 0.15).     

Femtosecond electron dynamics on solid surfaces probed by low energy ion scattering and stimulated desorption of secondary ions

The cations emission from condensed matter surfaces has been investigated on the basis of localization and delocalization of valence hole(s) in the femtosecond timescale. The yield of scattered H⁺ (E₀=100 eV), though negligibly small from the Pt(1 1 1) substrate, increases markedly when Ar is adsorbed on it, indicating the localization of a valence (H⁺ 1s) hole on the physisorbed Ar layer. However, the yield of H⁺ scattered from a thick H₂O layer is considerably small relative to that from Ar and CO layers. The delocalized nature of a valence hole in water ice is caused by some covalency in hydrogen bonds. Hydrated protons, H⁺(H₂O)_n, n=1,2,…,10, are emitted efficiently in electron stimulated desorption from water molecules adsorbed on the Ar layer; the ion yields are highest at the initial adsorption stage and decay steeply with increasing coverage. Coulombic repulsion between the hydrated protons confined in physisorbed nanoclusters is responsible for the explosive ion emission.     

Comparison of secondary ion intensity enhancement from polymers on silicon and silver substrates by using Au-TOF-SIMS

The usefulness of the usage of cluster primary ion source together with an Ag substrate and detection of Ag cationized molecular ions was studied from the standpoint to realize high sensitivity TOF-SIMS analysis of organic materials. Although secondary ions from polymer thin films on a Si substrate can be detected in a higher sensitivity with Au₃⁺ cluster primary ion compared with Ga⁺ ion bombardment, it was clearly observed that the secondary ion intensities from samples on an Ag substrate showed quite a different tendency from that on Si. When monoatomic primary ions, e.g., Au⁺ and Ga⁺, were used for the measurement of the sample on an Ag substrate, [M+Ag]⁺ ions (M corresponds to polyethylene glycol molecule) were detected in a high sensitivity. On the contrary, when Au₃⁺ was used, no intensity enhancement of [M+Ag]⁺ ions was observed. The acceleration energy dependence of the detected secondary ions implies the different ionization mechanisms on the different substrates.     

Energy distributions of atomic and molecular ions sputtered by C60 projectiles

In the process of investigating the interaction of fullerene projectiles with adsorbed organic layers, we measured the kinetic energy distributions (KEDs) of fragment and parent ions sputtered from an overlayer of polystyrene (PS) oligomers cast on silver under 15 keV C₆₀⁺ bombardment. These measurements have been conducted using our TRIFT™ spectrometer, recently equipped with the C₆₀⁺ source developed by Ionoptika, Ltd. For atomic ions, the intensity corresponding to the high energy tail decreases in the following order: C⁺(E^−0.4) > H⁺(E^−1.5) > Ag⁺(E^−3.5). In particular, the distribution of Ag⁺ is not broader than those of Ag₂⁺ and Ag₃⁺ clusters, in sharp contrast with 15 keV Ga⁺ bombardment. On the other hand, molecular ions (fragments and parent-like species) exhibit a significantly wider distribution using C₆₀⁺ instead of Ga⁺ as primary ions. For instance, the KED of Ag-cationized PS oligomers resembles that of Ag⁺ and Ag_n⁺ clusters. A specific feature of fullerene projectiles is that they induce the direct desorption of positively charged oligomers, without the need of a cationizing metal atom. The energy spectrum of these PS⁺ ions is significantly narrower then that of Ag-cationized oligomers. For characteristic fragments of PS, such as C₇H₇⁺ and C₁₅H₁₃⁺ and polycyclic fragments, such as C₉H₇⁺ and C₁₄H₁₀⁺, the high energy decay is steep (E⁻⁴ − E⁻⁸). In addition, reorganized ions generally show more pronounced high energy tails than characteristic ions, similar to the case of monoatomic ion bombardment. This observation is consistent with the higher excitation energy needed for their formation. Finally, the fraction of hydrocarbon ions formed in the gas phase via unimolecular dissociation of larger species is slightly larger with gallium than with fullerene projectiles.     

Secondary ion emission under the bombardment of Si by multiply charged Si q+ ions

The spectra of secondary ion emission under the bombardment of a B-doped Si target by multiply charged Si ^q+ ions (q = 1?C5) have been studied in the energy range of 1 to 10 keV per unit of charge. A multifold increase in the yield of secondary cluster Sk _n ⁺ ions, multiply charged Si ^q/+ ion (q = 1?C3), and H⁺, C⁺, B⁺, Si₂N⁺, Si₂O⁺ is observed as the charge of the multiply charged ions increases. The increase in the yield of secondary ions with increasing charge of the multiply charged-ion charge is most significant for ions with relatively high ionization potentials.     

Collision cross sections and swarm coefficients of water vapour ion clusters (H2O)nH+ with n = 1, 2 and 3 in N2, O2 and air

The ion swarm transport coefficients such as reduced mobility, diffusion coefficients and reaction rates of three water vapour ion clusters (H₂O) _n H⁺ (with n = 1, 2 and 3) in N₂ and O₂ have been determined from a Monte Carlo simulation using calculated and measured elastic and inelastic collision cross sections. The elastic momentum transfer cross sections have been determined from a semi-classical JWKB approximation based on a rigid core interaction potential model. The inelastic cross sections have been deduced from the measured ones in the case of similar ion cluster. Then, the cross sections sets are fitted using either the measured reduced mobility at low electric field in the case of (H₂O) _n H⁺ in N₂ or the zero-field mobility calculated from the Satoh's relation and the measured ones in N₂. From the sets of elastic and inelastic collision cross sections thus obtained in pure N₂ and O₂, the ion transport and reaction coefficients for (H₂O) _n H⁺ are then calculated in dry air and also extended over a wide range of reduced electric field in N₂ and O₂. These ion data are very useful for modelling and simulation of non-equilibrium electrical discharges more particularly in humid gases at atmospheric pressure.     

Microhydration of the methylene blue cation in an electrospray ion source

Microhydrated methylene blue cations, MB⁺(H₂O) _n , are produced in an electrospray ion source and their size-distributions are measured as a function of the source temperature. A series of MB⁺(H₂O) _n ions is observed up to n ≃ 60. A striking feature observed in the mass spectra is that the series of hydrated ions starts at n = 4; intensities of n = 1–3 are extremely suppressed. The absence of n = 1–3 ions is well explained by the energetics concerning evaporation processes of water molecules, based on stable structures and the binding energies of MB⁺(H₂O) _n ions calculated by DFT calculations up to n = 5. MB⁺(H₂O) _n ions for n > 4 evaporate a single water molecule sequentially, while MB⁺(H₂O)₄ tends to fragment into MB⁺ and (H₂O)₄ rather than MB⁺(H₂O)₃ and an H₂O molecule. We have observed a clear magic peak at n = 24, which strongly suggests that the MB⁺(H₂O)₂₄ ion is formed by attaching a neutral (H₂O)₂₀ cage onto an MB⁺(H₂O)₄ ion.     

A new analysis of the depolymerized fragments of lignin polymer in the plant cell walls using ToF-SIMS

High mass resolution ToF-SIMS spectra by Au⁺ primary ion bombardment were used to investigate exact structures of characteristic ions of lignin in plant cell walls. Previous study using Ga primary ion bombardment showed the characteristic peaks of guaiacyl lignin at m/z 137 ([C₈H₉O₂]⁺) and 151 ([C₈H₇O₃]⁺ and [C₉H₁₁O₂]⁺), but it was unclear whether the peak at m/z 151 in the spectrum of lignin in situ in plant cell walls is actually a double-component, [C₈H₇O₃]⁺ (151.0394) and [C₉H₁₁O₂]⁺ (151.0758). This report achieved a higher mass resolution with lignin samples, showing that the peak at m/z 151 is dominated by the C₆-C₁ benzoyl ion, [C₈H₇O₃]⁺, not the C₆-C₂ ion, [C₉H₁₁O₂]⁺.     

A comparative study of secondary ion yield from model biological membranes using Aun and C60 primary ion sources

Au_n⁺ and C₆₀⁺ primary ion sources have been used to acquire spectra from phospholipids, symmetric liposomes and asymmetric liposomes. We demonstrate that when using different ion beams different chemical information can be obtained. Symmetric and asymmetric liposomes, with 95% asymmetry, were produced and analysed with Au⁺, Au₃⁺ and C₆₀⁺ primary ion beams. C₆₀⁺ gave the greatest yield from the symmetric liposome but after correcting for the yield effects on the data obtained from the asymmetric liposome it has been shown that C₆₀⁺ is the most surface sensitive, providing the least information from the inner leaflet of the liposome. Au_n⁺ provides the greatest amount of information from the inner leaflet. The results present the possibility of designing ToF-SIMS experiments that selectively probe specific regions of a (bio)molecular surface.     

Secondary ion emission from a GaAs single crystal upon bombardment with Bi<Stack> <Subscript> <Emphasis Type="Italic">m</Emphasis> </Subscript> <Superscript>+</Superscript> </Stack> cluster ions

Secondary-ion mass spectra and energy distributions upon bombarding a gallium arsenide single crystal using Bi_m⁺(m = 1–5) cluster ions with energies of 2–12 keV are investigated. The gallium cluster ion yield grew nonadditively with the number of atoms in the cluster projectiles. A quasi-thermal component found in the energy spectra of secondary Ga⁺ and Ga₂⁺ ions is indicative of the occurrence of the thermal spike mode upon cluster ion bombardment. The quasi-thermal component in the yield of atomic Ga⁺ ions upon bombardment with Bi₂⁺–Bi₅⁺–ions is 35–75%.     

Influence of primary ion species on the secondary cluster ion emission process from SAMs of hexadecanethiol on gold

In order to investigate the secondary cluster ion emission process of organo-metallic compounds under keV ion bombardment, self-assembled monolayers (SAMs) of alkanethiols on gold are ideal model systems. In this experimental study, we focussed on the influence of the primary ion species on the emission processes of gold-alkanethiolate cluster ions from a hexadecanethiol SAM on gold. For this purpose, we carried out time-of-flight secondary ion mass spectrometry (TOF-SIMS) measurements using the following primary ion species and acceleration voltages: Ar⁺, Xe⁺, SF₅⁺ (10 kV), Bi⁺, Bi₃⁺(25 kV), Bi₃²⁺, Bi₅²⁺, Bi₇²⁺ (25 kV).It is well known that molecular ions M⁻ and gold-alkanethiolate cluster ions Au_xM_y⁻ with M = S-(CH₂)₁₅-CH₃, x − 3 ≤ y ≤ x + 1, x, y > 0, show intense peaks in negative mass spectra. We derived yields Y_SI exemplarily for the molecular ions M⁻ and the gold-hexadecanethiolate cluster ions Au_y+1M_y⁻ up to y = 8 and found an exponentially decreasing behaviour for increasing y-values for the cluster ions.In contrast to the well-known increase in secondary ion yield for molecular secondary ions when moving from lighter to heavier (e.g. Ar⁺ to Xe⁺) or from monoatomic to polyatomic (e.g. Xe⁺ to SF₅⁺) primary ions, we find a distinctly different behaviour for the secondary cluster ions. For polyatomic primary ions, there is a decrease in secondary ion yield for the gold-hexadecanethiolate clusters whereas the relative decrease of the secondary ion yield ξ_Y with increasing y remains almost constant for all investigated primary ions.     

Yields and ionization probabilities of sputtered Inn particles under atomic and polyatomic Aum ion bombardment

The emission of neutral and charged atoms and clusters from a polycrystalline indium surface under bombardment with 5 and 10 keV Au, Au₂, Au₃ and Au₅ projectiles was investigated. Single photon laser postionization was utilized for the detection of sputtered neutral particles. Secondary ions were detected without the laser under otherwise exactly the same experimental conditions. The relative cluster yields were found to be enhanced under polyatomic projectile bombardment, more so the larger the number of atoms in the sputtered cluster. The ionization probability strongly increases with increasing cluster size, but is essentially independent of the projectile impact energy. At a fixed impact energy, the ionization probability of sputtered monomers was found to decrease with increasing number of constituent gold atoms per projectile, but there was no detectable effect for sputtered dimers and larger clusters.