Control of a- and c-plane preferential orientations of ZnO thin films

We report orientation-controllable growth of ZnO thin films and their orientation-dependent electrical characteristics. ZnO thin films were deposited on single-crystalline (1 0 0) LaAlO₃ and (1 0 0) SrTiO₃ substrates using pulsed laser deposition (PLD) at different substrate temperatures (400-800 °C). It was found that the orientation of ZnO films could be controlled by using different substrates of single-crystalline (1 0 0) LaAlO₃ and (1 0 0) SrTiO₃. The a-plane () and c-plane (0 0 0 2) oriented ZnO films are formed on LaAlO₃ and SrTiO₃, respectively. In both cases, the degree orientation increased with increasing deposition temperature T_s. Both the surface free energy and the degree of lattice mismatch are ascribed to play an important role for the orientation-controllable growth. Further characterization show that the grain size of the films with both orientations increases for a substrate temperature increase (i.e. from T_s = 400 °C to T_s = 800 °C), whereas the electrical properties of ZnO thin films depend upon their crystalline orientation, showing lower electrical resistivity values for a-plane oriented ZnO films.     

Effect of substrate temperature and annealing temperature on the structural, electrical and microstructural properties of thin Pt films by rf magnetron sputtering

Influence of both substrate temperature, T_s, and annealing temperature, T_a, on the structural, electrical and microstructural properties of sputtered deposited Pt thin films have been investigated. X-ray diffraction results show that as deposited Pt films (T_s = 300, 400 °C) are preferentially oriented along (1 1 1) direction. A little growth both along (2 0 0) and (3 1 1) directions are also noticed in the as deposited Pt films. After annealing in air (T_a = 500-700 °C), films become strongly oriented along (1 1 1) plane. With annealing temperature, average crystallite size, D, of the Pt films increases and micro-strain, e, and lattice constant, a₀, decreases. Residual strain observed in the as deposited Pt films is found to be compressive in nature while that in the annealed films is tensile. This change in the strain from compressive to tensile upon annealing is explained in the light of mismatch between the thermal expansion coefficients of the film material and substrate. Room temperature resistivity of Pt films is dependant on both the T_s and T_a of the films. Observed decrease in the film resistivity with T_a is discussed in terms of annihilation of film defects and grain-boundary. Scanning electron microscopic study reveals that as the annealing temperature increases film densification improves. But at an annealing temperature of ∼600 °C, pinholes appear on the film surface and the size of pinhole increases with further increase in the annealing temperature. From X-ray photoelectron spectroscopic analysis, existence of a thin layer of chemisorbed atomic oxygen is detected on the surfaces of the as deposited Pt films. Upon annealing, coverage of this surface oxygen increases.     

Characterization of chemically deposited ZnSe/SnO2/glass films: Influence of annealing in Ar atmosphere on physical properties

The Zinc Selenide (ZnSe) thin films have been deposited on SnO₂/glass substrates by a simple and inexpensive chemical bath deposition (CBD). The structural, optical and electrical properties of ZnSe films have been characterized by X-ray diffraction (XRD), Energy Dispersive X-ray Analysis (EDAX), optical absorption spectroscopy, and four point probe techniques, respectively. The films have been subjected to different annealing temperature in Argon (Ar) atmosphere. An increase in annealing temperature does not cause a complete phase transformation whereas it affects the crystallite size, dislocation density and strain. The optical band gap (E_g) of the as-deposited film is estimated to be 3.08 eV and decreases with increasing annealing temperature down to 2.43 eV at 773 K. The as-deposited and annealed films show typical semiconducting behaviour, dρ/dT > 0. Interestingly, the films annealed at 373 K, 473 K, and 573 K show two distinct temperature dependent regions of electrical resistivity; exponential region at high temperature, linear region at low temperature. The temperature at which the transition takes place from exponential to linear region strongly depends on the annealing temperature.     

Structural and electrical transport properties of ZnxFe3−xO4 thin film deposited on Si (1 1 1) by pulsed-laser deposition

Polycrystalline thin films of Fe_3−xZn_xO₄ (x = 0.0, 0.01 and 0.02) were prepared by pulsed-laser deposition technique on Si (1 1 1) substrate. X-ray diffraction studies of parent as well as Zn doped magnetite show the spinel cubic structure of film with (1 1 1) orientation. The order–disorder transition temperature for Fe₃O₄ thin film with thickness of 150 nm are at 123 K (Si). Zn doping leads to enhancement of resistivity by Zn²⁺ substitution originates from a decrease of the carrier concentration, which do not show the Verwey transition. The Raman spectra for parent Fe₃O₄ on Si (1 1 1) substrate shows all Raman active modes for thin films at energies of T_2g¹, T_2g³, T_2g², and A_1g at 193, 304, 531 and 668 cm⁻¹. It is noticed that the frequency positions of the strongest A_1g mode are at 668.3 cm⁻¹, for all parent Fe₃O₄ thin film shifted at lower wave number as 663.7 for Fe_2.98Zn_0.02O₄ thin film on Si (1 1 1) substrate. The integral intensity at 668 cm⁻¹ increased significantly with decreasing doping concentration and highest for the parent sample, which is due to residual stress stored in the surface.     

Surface textured ZnO:Al thin films by pulsed DC magnetron sputtering for thin film solar cells applications

Transparent conducting thin films of ZnO:Al (Al-doped ZnO, AZO) were prepared via pulsed DC magnetron sputtering with good transparency and relatively lower resistivity. The AZO films with 800 nm in thickness were deposited on soda-lime glass substrates keeping at 473 K under 0.4 Pa working pressure, 150 W power, 100 μs duty time, 5 μs pulse reverse time, 10 kHz pulse frequency and 95% duty cycle. The as-deposited AZO thin films has resistivity of 6.39 × 10⁻⁴ Ω cm measured at room temperature with average visible optical transmittance, T_total of 81.9% under which the carrier concentration and mobility were 1.95 × 10²¹ cm⁻³ and 5.02 cm² V⁻¹ s⁻¹, respectively. The films were further etched in different aqueous solutions, 0.5% HCl, 5% oxalic acid, 33% KOH, to conform light scattering properties. The resultant films etched in 0.5% HCl solution for 30 s exhibited high T_total = 78.4% with haze value, H_T = 0.1 and good electrical properties, ρ = 8.5 × 10⁻⁴ Ω cm while those etched in 5% oxalic acid for 150 s had desirable H_T = 0.2 and relatively low electrical resistivity, ρ = 7.9 × 10⁻⁴ Ω cm. However, the visible transmittance, T_total was declined to 72.1%.     

Physico-chemical, optical and electrochemical properties of iron oxide thin films prepared by spray pyrolysis

Iron oxide thin films were prepared by spray pyrolysis technique onto glass substrates from iron chloride solution. They were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and (UV-vis) spectroscopy. The films deposited at T_s ≤ 450 °C were amorphous; while those produced at T_sub = 500 °C were polycrystalline α-Fe₂O₃ with a preferential orientation along the (1 0 4) direction. By observing scanning electron microscopy (SEM), it was seen that iron oxide films were relatively homogeneous uniform and had a good adherence to the glass substrates. The grain size was found (by RX) between 19 and 25 nm. The composition of these films was examined by X-ray photoelectron spectroscopy and electron probe microanalysis (EPMA). These films exhibited also a transmittance value about 80% in the visible and infrared range. The cyclic voltammetry study showed that the films of Fe₂O₃ deposited on ITO pre-coated glass substrates were capable of charge insertion/extraction when immersed in an electrolyte of propylene carbonate (PC) with 0.5 M LiCLO₄.     

Effect of indium incorporation on properties of SnS thin films prepared by spray pyrolysis

Tin sulphide (SnS) thin films were deposited on glass substrate at different substrate temperature (T_s = 325 °C, 350 °C and 375 °C) by pyrolytic decomposition using stannous chloride and thiourea as precursor solutions. Also, indium-doped SnS thin films were prepared by using InCl₃ as dopant source. The dopant concentration [In/Sn] was varied from 2 at% to 6 at%. The XRD analysis revealed that the films were polycrystalline in nature having orthorhombic crystal structure with a preferred grain orientation along (1 1 1) plane. Due to In doping, the orientation of the grains in the (1 1 1) plane was found to be deteriorated. Atomic force microscopy (AFM) measurements revealed that the surface roughness of the films decreased due to indium doping. The optical properties were investigated by measuring the transmittance characteristics which were used to find the optical band gap energy, refractive index and extinction coefficient. The energy band gap value was decreased from 1.60 to 1.43 eV with increasing In concentration. The photoluminescence (PL) measurements of thin films showed strong emission band centered at 760 nm. Using Hall Effect measurements electrical resistivity, carrier concentration and Hall mobility have been determined.     

Structural and electrical transport properties of Nb-doped TiO2 films deposited on LaAlO3 by rf sputtering

We have investigated the structural and electrical transport properties of Nb-doped TiO₂ films deposited on (1 0 0) LaAlO₃ substrates by rf magnetron sputtering at temperatures ranging from 873 K to 1073 K. Films deposited below 998 K are anatase, and mixed phases between anatase and rutile exist in the film grown at higher temperatures. We find that films deposited at low temperatures exhibit semiconductor behavior, while metallic conductivity is observed in the most conducting film deposited at 998 K. For this sample, compared to electron-phonon scattering mechanism, electron-phonon-impurity interference effect plays an important role in its electron transport process. Moreover, the temperature coefficient of the resistivity for the film deposited at 1073 K is negative from 2 K to 300 K. The temperature dependence of resistivity for the film is described by ∼exp(b/T)^1/2 at temperatures from 80 K down to 30 K, and by the fluctuation induced tunneling model from 80 K to 300 K.     

Electrical behavior of some silver-doped lanthanum-based CMR materials

With a view to understand the structural, magnetic and electrical properties of La_1−xAg_xMnO₃ (x=0.05-0.3), a series of samples were prepared by polyvinyl alcohol (PVA) gel route. It has been found that both the metal-insulator and ferro- to paramagnetic transition temperatures after increasing up to the composition x=0.20, are found to remain constant thereafter. The electrical resistivity vs. temperature plot of the sample x=0.10 is found to exhibit an insulating behavior below 36 K, while the sample, x=0.20 exhibits two peaks, and the observed behavior is explained on the basis of the phase separation model. The low-temperature (T<T_P), electrical resistivity data were analyzed by a theoretical model, ρ=ρ₀+ρ₂T²+ρ_4.5T^4.5, indicating the importance of grain/domain boundary effects, electron-electron and two-magnon scattering processes. The low-temperature resistivity data (T<50 K) were fitted to an equation, which is based on the combined effect of weak localization, electron-electron and electron-phonon scattering.     

Large negative magnetoresistance in thiospinel CuCrZrS4

We report on large negative magnetoresistance observed in ferromagnetic thiospinel compound CuCrZrS₄. The electrical resistivity increased with decreasing temperature according to the exp(T₀/T)^1/2, an expression derived from variable range hopping with strong electron-electron interaction. The resistivity under a magnetic field was expressed by the same form with the characteristic temperature T₀ decreasing with increasing magnetic field. Magnetoresistance ratio ρ(T,0)/ρ(T,H) is 1.5 for H=90 kOe at 100 K and increases divergently with decreasing temperature reaching 80 at 16 K. Results of magnetization measurements are also presented. A possible mechanism of the large magnetoresistance is discussed.     

Structural and surface properties of Si1−xGex thin films obtained by reduced pressure CVD

This paper investigates the structure and surface characteristics, and electrical properties of the polycrystalline silicon-germanium (poly-Si_1−xGe_x) alloy thin films, deposited by vertical reduced pressure CVD (RPCVD) in the temperature range between 500 and 750 °C and a total pressure of 5 or 10 Torr. The samples exhibited a very uniform good quality films formation, with smooth surface with rms roughness as low as 7 nm for all temperature range, Ge mole fraction up to 32% (at 600 °C), textures of 〈2 2 0〉 preferred orientation at lower temperatures and strong 〈1 1 1〉 at 750 °C, for both 5 and 10 Torr deposition pressures. The ³¹P⁺ and ¹¹B⁺ doped poly-Si_1−xGe_x films exhibited always lower electrical resistivity values in comparison to similar poly-Si films, regardless of the employed anneal temperature or implantat dose. The results indicated also that poly-Si_1−xGe_x films require much lower temperature and ion implant dose than poly-Si to achieve the same film resistivity. These characteristics indicate a high quality of obtained poly-Si_1−xGe_x films, suitable as a gate electrode material for submicron CMOS devices.     

Synthesis and characterization of Al-N codoped p-type ZnO epitaxial films using high-temperature homo-buffer layer

Al-N codoped p-type ZnO thin films have been prepared by DC magnetron reactive sputtering reproducibly using a high-temperature (HT) homo-buffer layer. The influence of HT buffer layer deposition time (T_ht) on film properties was investigated by X-ray diffraction (XRD), scanning electron micro-spectra (SEM) and Hall measurement. The Al-N codoped ZnO film was improved evidently in its crystal quality by varying the value of T_ht. Results of Hall effect showed that all of the Al-N codoped ZnO thin films were p-type conduction and had resistivity mainly below 50 Ω cm. The optimum deposition time of HT buffer layer is around 3 min from the comprehensive consideration of structural, electrical, and optical properties. The obtained ZnO thin film can meet the need of application in optoelectronic devices based on ZnO.     

High-throughput characterization of BixY3−xFe5O12 combinatorial thin films by magneto-optical imaging technique

Bi_xY_3−xFe₅O₁₂ thin films have been grown on GGG (Gd₃Ga₅O₁₂) (1 1 1) substrates by the combinatorial composition-spread techniques under substrate temperature (T_sub) ranging from 410 to 700 °C and O₂ pressure of 200 mTorr. In order to study the effect of substrates on the deposition of Bi_xY_3−xFe₅O₁₂ thin films, garnet substrates annealed at 1300 °C for 3 h were also used. Magneto-optical properties were characterized by our home-designed magneto-optical imaging system. From the maps of Faraday rotation angle θ_F, it was evident that the Faraday effect appears only when T_sub = 430-630 °C. θ_F reaches to the maximum value (∼6°/μm, λ = 632 nm) at 500 °C, and is proportional to the Bi contents. XRD and EPMA analyses showed that Bi ions are easier to substitute for Y sites and better crystallinity is obtained for annealed substrates than for commercial ones.     

Enhanced ferroelectric property of (Pb0.95Ca0.05)(Nb0.02Zr0.80Ti0.20)O3 thin films prepared by RF magnetron sputtering

(Pb_0.95Ca_0.05)(Nb_0.02Zr_0.80Ti_0.20)O₃ [PCNZT] thin films were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering with and without a LaNiO₃ [LNO] buffer layer. Ca and Nb elements in PZT films enhance the ferroelectric property, LaNiO₃ buffer layer improves the crystal quality of the PCNZT thin films. PCNZT thin films possess better ferroelectric property than that of PZT films for Ca and Nb ion substitution, moreover, PCNZT thin films with a LNO buffer layer possess (1 0 0) orientation and good ferroelectric properties with high remnant polarization (P_r = 38.1 μC/cm²), and low coercive field (E_c = 65 kV/cm), which is also better than that of PCNZT thin films without a LNO buffer layer (P_r = 27.9 μC/cm², E_c = 74 kV/cm). The result shows that enhanced ferroelectric property of PZT films can be obtained by ion substitution and buffer layer.     

Substrate and orientation influence on electrical properties of sputtered La-doped PZT thin films

Pb_1−2y/3La_yZr_xTi_1−xO₃ (PLZT) thin films have been prepared “in situ” by multi-target sputtering on Silicon, LaAlO₃ (LAO) and MgO substrates covered with a Pt bottom electrode. The purpose was to grow tetragonal PLZT films (Zr/Ti = 28/72 with different La contents) on these various substrates and to compare their electrical properties. To this aim, Pt was first deposited on the three different substrates to get (1 1 1)Pt/Si, (1 1 1)Pt/LAO and (2 0 0)Pt/MgO. Then PLZT was deposited in a same run on these three kinds of substrates and the influence of La contents and film orientation on electrical properties was investigated. The La content was varied from y = 0 to y = 32 in order to explore the phase transition between ferroelectric and paraelectric phases as a function of the substrate. For large amount of Lanthanum, relaxor behavior has been observed and studied.     

Decomposition of thin titanium deuteride films; thermal desorption kinetics studies combined with microstructure analysis

The thermal evolution of deuterium from thin titanium films, prepared under UHV conditions and deuterated in situ at room temperature, has been studied by means of thermal desorption mass spectrometry (TDMS) and a combination of scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The observed Ti film thickness dependent morphology was found to play a crucial role in the titanium deuteride (TiD_y) film formation and its decomposition at elevated temperatures. TDMS heating induced decomposition of fine-grained thin Ti films, of 10-20 nm thickness, proceeds at low temperature (maximum peak temperature T_m about 500 K) and its kinetics is dominated by a low energy desorption (E_D = 0.61 eV) of deuterium from surface and subsurface areas of the Ti film. The origin of this process is discussed as an intermediate decomposition state towards recombinative desorption of molecular deuterium. The TiD_y bulk phase decomposition becomes dominant in the kinetics of deuterium evolution from thicker TiD_y films. The dominant TDMS peak at approx. T_m = 670 K, attributed to this process, is characterized by E_D = 1.49 eV.     

Effect of molecular structure on bias stress effect in organic thin-film transistors

Two thiophene-phenylene semiconductors, bis(2-phenylethynyl) end-substituted oligothiophenes (diPhAc-nTs, n = 2, 3), were studied as active layers in organic thin film transistors (OTFTs). Structural and electrical properties of such high vacuum evaporated thin films were compared to pentacene. All three oligomers behave as p-type semiconducting layers into OTFTs. In the same preparation and measurement conditions, diPhAc-3T possesses two of incontrovertible attributes of OTFTs for low cost applications, a high air-stable mobility at low substrate temperature (T_sub), i.e. typically 25 °C together with a reduced bias stress effect compared to the well-known pentacene semiconductor. This study brings to light on the role of the molecular structure involved in the active layer in thin-film devices and describes effects as thin film morphology as important parameters when optimizing the structure of OTFTs.     

Characterization of SnO2 obtained from the thermal oxidation of vacuum evaporated Sn thin films

Tin oxide has been prepared by thermal oxidation of evaporated tin thin films onto pyrex glass substrates. Films oxidation was achieved in air at a temperature of 600 °C with varied duration from 20min to 3 h. Structural, optical and electrical properties of the films were characterized by means of X-ray diffraction, UV–vis spectroscopy and electrical resistivity measurements respectively. The X-ray analysis revealed the transformation of Sn into SnO₂ with preferential orientation along (101) plans. No intermediate phases such as SnO and Sn₃O₄ were evidenced. It was also found that the SnO₂ crystallites orientation changed with the annealing time due to the strain energy effect. Both band gap energy and electrical resistivity decrease with annealing time due to the crystalline quality improvement and films densification. We have noticed that oxidation at 600 °C for 3 h leads to transparent and conductive films with suitable properties for photovoltaic applications.     

High pressure effects on the electrical resistivity behavior of the Kondo lattice, YbPd2Si2

We report the influence of external high-pressure (P up to 8 GPa) on the temperature (T) dependence of electrical resistivity (ρ) of a Yb-based Kondo lattice, YbPd₂Si₂, which does not undergo magnetic ordering under ambient pressure condition. There are qualitative changes in the ρ(T) behavior due to the application of external pressure. While ρ is found to vary quadratically below 15 K (down to 45 mK) characteristic of Fermi-liquids, a drop is observed below 0.5 K for P=1 GPa, signaling the onset of magnetic ordering of Yb ions with the application of P. The T at which this fall occurs goes through a peak as a function of P (8 K for P=2 GPa and about 5 K at high pressures), mimicking Doniach's magnetic phase diagram. We infer that this compound is one of the very few Yb-based stoichiometric materials, in which one can traverse from valence fluctuation to magnetic ordering by the application of external pressure.     

Thermoelectric power of potassium doped lanthanum manganites at low temperatures

The temperature-dependent resistivity and thermoelectric power of monovalent (K) doped La_1−xK_xMnO₃ polycrystalline pellets (x=0.05, 0.10 and 0.15) between 50 and 300 K are reported. K substitution enhances the conductivity of this system. Curie temperature (T_C) also increases from 260 to 309 K with increasing K content. In the paramagnetic region (T>T_C), the electrical resistivity is well represented by adiabatic polaron hopping, while in the ferromagnetic region (T<T_C), the resistivity data show a nearly perfect fit for all the samples to an expression containing, the residual resistivity, spin-wave and two-magnon scattering and the term associated with small-polaron metallic conduction, which involves a relaxation time due to a soft optical phonon mode. Small polaron hopping mechanism is found to fit well to the thermoelectric power (S) data for T>T_C whereas at low temperatures (T<T_C) in ferromagnetic region (S_FM), S_FM is well explained with the spin-wave fluctuation and electron–magnon scattering. Both, resistivity and thermopower data over the entire temperature range (50–300 K) are also examined in light of a two-phase model based on an effective medium approximation.