Synthesis and characterization of a polyaniline-modified SnO<Subscript>2</Subscript> nanocomposite

Polyaniline-modified tin oxide and tin oxide nanoparticles were synthesized using a solution route technique. The obtained pristine products were characterized with X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, and optical absorption spectroscopy. Thermogravimetric analysis results showed that the polyaniline-modified SnO₂ nanoparticles exhibit higher thermal stability than the SnO₂ nanoparticles. Scanning electron microscopy analysis on the as-synthesized powders showed spherical particle in the range of 50–100 nm.     

Al<Subscript>2</Subscript>O<Subscript>3</Subscript> plasma production during pulsed laser deposition

A Nd:YAG laser operating in second harmonic (532 nm), 3 ns pulse duration, 150 mJ pulse energy, and 10 Hz repetition rate, is employed to irradiate Al₂O₃ target placed in high vacuum. The produced plasma is investigated by an ion collector used in time-of-flight configuration and by a mass quadrupole spectrometer, in order to determine the equivalent plasma temperature and the atomic and molecular composition. Pulsed laser deposition technique has been used to produce thin films on different substrates placed close to the target. Different surface analyses, such as energy dispersive X-ray fluorescence (EDXRF), X-ray photoelectron spectroscopy (XPS) and surface profilometry are employed to characterize the produced films. Measurements of ablation yield, plasma equivalent temperature, acceleration voltage and characterization of grown thin films are presented and discussed.     

Growth and thermoelectric properties of FeSb<Subscript>2</Subscript> films produced by pulsed laser deposition

Thermoelectric FeSb₂ films were produced by pulsed laser deposition on silica substrates in a low-pressure Ar environment. The growth conditions for near phase-pure FeSb₂ films were confirmed to be optimized at a substrate temperature of 425°C, an Ar pressure of 2 Pa, and deposition time of 3 h by ablating specifically prepared compound targets made of Fe and Sb powders in atomic ratio of 1:4. The thermoelectric transport properties of FeSb₂ films were investigated. Pulsed laser deposition was demonstrated as a method for production of good-quality FeSb₂ films.     

Synthesis and nanostructural investigation of TiO<Subscript>2</Subscript> nanorods doped by SiO<Subscript>2</Subscript>

TiO₂ Nano rods can be used as dye-sensitized solar cells, various sensors and photocatalysts. These nanorods are synthesized by a hydrothermal corrosion process in NaOH solution at 200°C using TiO₂ powder as the source material. In the present work, the synthesis of TiO₂ nanorods in anatase, rutile and Ti₇O₁₃ phases and synthesis of TiO₂ nanorods by incorporating SiO₂ dopant, using the sol–gel method and alkaline corrosion are reported. The morphologies and crystal structures of the TiO₂ nanorods are characterized using field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) study. The obtained results show not only an aggregation structure at high calcination temperatures with spherical particles but also Ti–O–Si bonds having four-fold coordination with oxygen in SiO^4 −.     

Synthesis and characterization of hollow nanoparticles of crystalline Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>

Although Gd₂O₃ (gadolinia) nanoparticle is the subject of intense research interest due to its magnetic property as well as controllable emission wavelengths by doping of various lanthanide ions, it is known to be difficult to prepare monodisperse crystalline gadolinia nanoparticles because it requires high temperature thermal annealing process to enhance the crystallinity. In this article, we demonstrate the synthesis of hollow nanoparticles of crystalline Gd₂O₃ by employing poly(N-vinylpyrrolidone) (PVP) to stabilize the surface of Gd(OH)CO₃·H₂O nanoparticles and to successively form SiO₂ shell as a protecting layer to prevent aggregation during calcinations processes. Silica shells could be selectively removed after calcinations by a treatment with basic solution to give hollow nanoparticles of crystalline Gd₂O₃. The formation mechanism of hollow nanoparticles could be suggested based on several characterization results of the size and shape, and crystallinity of Gd₂O₃ nanoparticles by TEM, SEM, and XRD.     

Synthesis of nanocrystalline SnO<Subscript>2</Subscript> in supercritical water

Nanocrystalline SnO₂ was synthesized in supercritical water at 385–415°C and 30 MPa (38–106 s residence time) in a tubular flow reactor from an aqueous solution of 0.1–0.4 M SnCl₄. The conversion rate was between 53 and 81%, but increased to 97.8% when 0.1 M NaOH was added. Nanoparticles were analyzed by a series of independent analytical techniques, including TEM, Raman, XRD, SEM, EDX and FT-IR. The initial size of the particles was about 3.7 nm. After calcination at 450°C for 2 h, the particle size increased to 4 nm. The particles were of low crystallinity, as indicated by the weak Raman and XRD signals. All particles were composed of Sn and O, as verified by the EDX spectra. The crystals were tetragonal, as confirmed by the weak XRD spectrum. After calcination at 600°C for 10 h, the particle size increased to 9 nm, while high crystallinity was confirmed by Raman and XRD analyses. All the crystals had the same structure, as indicated by TEM electron diffraction patterns. Using this one-step supercritical water process, nanoparticles of SnO₂ can be conveniently produced continuously in a flow reactor in less than 2 min.     

Optical properties of SrTiO<Subscript>3</Subscript> thin films by pulsed laser deposition

SrTiO₃ thin films were prepared on a fused-quartz substrate by pulsed laser deposition (PLD). Dense and homogeneous films with a thickness of 260 nm were prepared. Optical constants (refractive index n and extinction coefficient k) were determined from the transmittance spectra using the envelope method. The optical band gap energy of the films was found to be 3.58 eV, higher than the 3.22 eV for bulk SrTiO₃, attributable to the film stress exerted by the substrate. The dispersion relation of the refractive index vs. wavelength follows the single electronic oscillator model. The refractive index and the packing density for the PLD-prepared SrTiO₃ thin films are higher than those for the SrTiO₃ films prepared by physical vapor deposition, sol–gel and RF sputtering. Received: 18 March 2002 / Accepted: 7 October 2002 / Published online: 8 January 2003 RID="*" ID="*"Corresponding author. Fax: +86-25/359-5535, E-mail: mszhang@nju.edu.cn     

Synthesis and enhanced acetone gas-sensing performance of ZnSnO<Subscript>3</Subscript>/SnO<Subscript>2</Subscript> hollow urchin nanostructures

A kind of novel ZnSnO₃/SnO₂ hollow urchin nanostructure was synthesized by a facile, eco-friendly two-step liquid-phase process. The structure, morphology, and composition of samples were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption–desorption techniques. The results revealed that many tiny needle-like SnO₂ nanowires with the average diameter of 5 nm uniformly grew on the surface of the ZnSnO₃ hollow microspheres and the ZnSnO₃/SnO₂ hollow urchin nanostructures with different SnO₂ content also were successfully prepared. In order to comprehend the evolution process of the ZnSnO₃/SnO₂ hollow urchin nanostructures, the possible growth mechanism of samples was illustrated via several experiments in different reaction conditions. Moreover, the gas-sensing performance of as-prepared samples was investigated. The results showed that ZnSnO₃/SnO₂ hollow urchin nanostructures with high response to various concentration levels of acetone enhanced selectivity, satisfying repeatability, and good long-term stability for acetone detection. Specially, the 10 wt% ZnSnO₃/SnO₂ hollow urchin nanostructure exhibited the best gas sensitivity (17.03 for 50 ppm acetone) may be a reliable biomarker for the diabetes patients, which could be ascribed to its large specific surface area, complete pore permeability, and increase of chemisorbed oxygen due to the doping of SnO₂.     

Pulsed laser deposition of BaGa<Subscript>2</Subscript>O<Subscript>4</Subscript>

This paper reports the first results obtained on monobarium gallate thin films grown on silicon and platinum coated substrates by pulsed laser deposition. The influence of oxygen background pressure and substrate (or post-annealing) temperature on the film properties was studied. The films were characterized by XRD, RHEED, AFM, photoelectron and electrical impedance spectroscopy. The structure analysis showed that the films crystallized into a hexagonal phase, most probably into (metastable) α-BaGa₂O₄. Depending on deposition conditions, films with different (from nearly epitaxial to polycrystalline) textures were obtained.     

Methane sensor based on SnO<Subscript>2</Subscript>/In<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> nanostructure

Two sets of samples of SnO₂/In₂O₃/TiO₂ system have been fabricated with different concentrations of component materials. In the first set TiO₂ with rutile structure was used, while in the second set it has the structure of anatase. Thin films (up to 50 nm) of obtained mixtures were deposited. Their sensitivity and selectivity with respect to methane (CH4) were studied. Nanostructure on the basis of 70%SnO₂ — 10%In₂O₃ — 20%TiO₂(anatase) exhibits sufficient sensitivity to methane.     

Synthesis and characterization of platinum nano sized particles by laser ablation in C<Subscript>2</Subscript>H<Subscript>6</Subscript>O<Subscript>2</Subscript> solution

Platinum nano sized particles (Pt NPs) are superior catalysts for many intentions, such as glucose sensors, cancer therapy, gas sensors, etc. Here, Pt NPs were produced by pulsed laser ablation in C₂H₆O₂ solution using Q-switched Nd:YAG laser, for the first time. Then, the influence of the laser fluence during synthesis of them was investigated; and they were characterized by UV–vis spectroscopy, TEM, FE-SEM, XRD, FT-IR, and Raman spectroscopy. The results showed that with increasing laser fluence, the mean particle size of the spherical NPs enhanced. Meanwhile, they had a polycrystalline cubic structure. Correspondingly, the plasmon peak position of generated NPs in the absorption spectra shifted from 257 to 266 nm, with a rise of laser fluence. The IR and Raman spectroscopy was used to achieve the information about the surface state of Pt NPs. We propose that the optimum adjusted laser fluence is an important factor to increase the ablation efficiency.     

Impedance spectroscopy analysis of Li<Subscript>2</Subscript>SnO<Subscript>3</Subscript>

In this work, Li₂SnO₃ has been synthesized by the sol–gel method using acetates of lithium and tin. Thermogravimetric analysis (TGA) has been applied to the precursor of Li₂SnO₃ to determine the suitable calcination temperature. The formation of the compound calcined at 800 °C for 9 h has been confirmed by X-ray diffraction (XRD) analysis. The Li₂SnO₃ is then pelletized and electrically characterized by using electrochemical impedance spectroscopy (EIS) in the frequency range from 50 Hz to 1 MHz. The complex impedance spectra clearly show the dominating presence of the grain boundary effect on electrical properties whereas the complex modulus plots reveal two semicircles which are due to the grain (bulk) and grain boundary. The spectra of imaginary parts of both impedance and modulus versus frequency show the existence of peaks with the modulus plots exhibiting two peaks that are ascribed to the grain and grain boundary of the material. The peak maximum shifts to higher frequency with an increase in temperature and the broad nature of the peaks indicates the non-Debye nature of Li₂SnO₃. The activation energy associated with the dielectric relaxation obtained from the electrical impedance spectra is 0.67 eV. From the electric modulus spectra, the activation energies related to conductivity relaxation in the grain and grain boundary of Li₂SnO₃ are 0.59 and 0.69 eV, respectively. The conductivity–temperature relationship is thermally assisted and obeys the Arrhenius rule with the activation energy of 0.66 eV. The conduction mechanism of Li₂SnO₃ is via hopping.     

Effect of oxygen partial pressure and VO<Subscript>2</Subscript> content on hexagonal WO<Subscript>3</Subscript> thin films synthesized by pulsed laser deposition technique

We report on the effect of oxygen partial pressure and vacuum annealing on structural and optical properties of pulsed laser-deposited nanocrystalline WO₃ thin films. XRD results show the hexagonal phase of deposited WO₃ thin films. The crystallite size was observed to increase with increase in oxygen partial pressure. Vacuum annealing changed the transparent as-deposited WO₃ thin film to deep shade of blue color which increases the optical absorption of the film. The origin of this blue color could be due to the presence of oxygen vacancies associated with tungsten ions in lower oxidation states. In addition, the effects of VO₂ content on structural, electrochemical, and optical properties of (WO₃)_1−x (VO₂) _x nanocomposite thin films have also been systematically investigated. Cyclic voltammogram exhibits a modification with the appearance of an extra cathodic peak for VO₂–WO₃ thin film electrode with higher VO₂ content (x ≥ 0.2). Increase of VO₂ content in (WO₃)_1−x (VO₂) _x films leads to red shift in optical band gap.     

Electrical and optical characterization of pulsed plasma of N<Subscript>2</Subscript>–H<Subscript>2</Subscript>

This paper considers the electrical and optical characterization of glow discharge pulsed plasma in N₂/H₂ gas mixtures at a pressures range between 0.5 and 4.0 Torr and discharge current between 0.2 and 0.6 A. Electron temperature and ion density measurements were performed employing a double Langmuir probe. They were found to increase rapidly as the H₂ percentage in the mixture was increased up to 20%. This increase slows down as the H₂ percentage in the gas mixture was increased above 20% at the same pressure. Emission spectroscopy was employed to observe emission from the pulsed plasma of a steady-state electric discharge. The discharge mainly emits within the range 280–500 nm. The emission consists of N₂ (C-X) 316, 336, 358 nm narrow peaks and a broad band with a maximum at λ_max = 427 nm. Also lines of N₂, N₂ ⁺ and NH excited states were observed. All lines and bands have their maximum intensity at the discharge current of 0.417 A. The intensities of the main bands and spectral lines are determined as functions of the total pressure and discharge current. Agreement with other theoretical and experimental groups was established.     

Red photoluminescence mechanism in SnO<Subscript>2</Subscript> nanostructures

Tin dioxide nanoribbons were fabricated for clarifying the origin of the red photoluminescence band. It is found that the red band abruptly decreases its intensity after annealing the nanoribbons in O₂. The time-resolved photoluminescence decay curve shows that the red band has a luminescence lifetime of ns. The electron spin resonance spectrum discloses that the red band is related to a kind of combined oxygen-vacancy (V _o⁺ and V _o⁺⁺) centers. Spectral analysis and theoretical calculation confirm that the red band arises from a transition between the combined oxygen-vacancy defect states in the band gap.     

Semiconducting SnO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> (S-T) composites for detection of SO<Subscript>2</Subscript> gas

SnO₂-TiO₂ (S-T) composites with different molar ratios were prepared by mechanical mixing followed by sintering at 700 °C for 4 h in air. The structural and microstructural properties of the composites were investigated using powder X-ray diffraction (PXRD) and scanning electron microscopy (SEM). S-T composites were investigated by introducing SO₂ to test their chemical stability using PXRD and SEM coupled with energy dispersive X-ray (EDX) analysis. The sensing performance was measured at different temperatures using various SO₂ concentrations (10–100 ppm). A composite comprising 25 mol% of SnO₂ and 75 mol% TiO₂ (S25-T75) exhibited the highest sensitivity comparing to other S-T composites studied under the presently investigated conditions. t ₉₀ (90 % of response time) was found to be ～5 min for thick pellet (~2 mm in thickness). SO₂ sensing mechanism has been explained through the band structure model.     

Characterization of Zn<Subscript>2</Subscript>SnO<Subscript>4</Subscript> Thin Films Prepared by RF Magnetron Sputtering

Zn₂SnO₄ (ZTO) is a stable semiconductor in ZnO–SnO₂ system and important transparent conducting oxide (TCO) predominantly used in optoelectronic devices. ZTO thin films were prepared by RF magnetron sputtering using Zn₂SnO₄ ceramic target in this paper. The effects of annealing temperatures and oxygen contents on characterization of ZTO thin films were studied. The results show that ZTO thin films prepared by RF magnetron sputtering are amorphous with an optical band gap of 3.22 eV. After annealing at 650°C in Ar atmosphere for 40 min, ZTO films possess a spinel structure with an optical band gap of 3.62 eV. The atomic force microscope (AFM) data of morphology reveals that the surface roughness of films is about 2 nm. The results of energy dispersive spectrometer (EDS) show that the concentration ratio of Zn to Sn is in the range from 1.44 to 1.57. The results of Hall-effect-measurement system reveal that the resistivity of films varies from 102 to 10–1 Ωcm, carrier concentration is about 10¹⁷ cm^–3, and mobility ranges from 10⁰ to 10¹ cm² v^–1 s^–1.     

Highly (100) oriented Pb(Zr<Subscript>0.52</Subscript>Ti<Subscript>0.48</Subscript>)O<Subscript>3</Subscript>/LaNiO<Subscript>3</Subscript> films grown on amorphous substrates by pulsed laser deposition

Pb(Zr_0.52Ti_0.48)O₃ (PZT)/LaNiO₃ (LNO) thin films with highly (100) out of plane orientation were produced on SiO₂/Si(100) and alkaline earth aluminosilicate glass substrates by pulsed laser deposition (PLD). Orientations of both PZT and LNO films were evaluated using X-ray diffraction. The pure (100)-oriented PZT/LNO films were obtained under optimized deposition conditions. Time of flight-secondary ion mass spectrometry analysis showed that LNO could effectively block interdiffusion between the PZT films and the substrates. Fairly smooth surfaces of the PZT films with roughness of about 4 nm were observed using an atomic force microscope. Cross sectional examination revealed that the films grew in columnar grains. The PZT films grown on both SiO₂/Si and glass substrates demonstrated very good ferroelectric characteristic at room temperature with remnant polarization of up to 26 μC/cm². PACS 79.20.DS; 77.84.DY; 78.70.Ck     

Ferromagnetism in Rh-doped SnO<Subscript>2</Subscript> from first-principles calculation

The electronic structures and magnetic properties for Rh-doped SnO₂ crystals have been investigated by density functional theory. The results demonstrate a magnetic moment, which mainly arises from d orbital of Rhodium, of 1.0 μ _B per Rhodium with a little contribution from the Oxygen atoms surrounding it. The Rh-doped SnO₂ system exhibits half-metallic ferromagnetism with high Curie temperature. Several doped configurations calculations show that there are some robust ferromagnetic couplings between these local magnetic moments. The p–d hybridization mechanism is responsible for the predicted ferromagnetism. These results suggest a recipe obtaining promising dilute magnetic semiconductor by doping nonmagnetic elements in SnO₂ matrix.     

Antiferromagnetic interactions in Er-doped SnO<Subscript>2</Subscript> DMS nanoparticles

Diluted magnetic semiconductor (DMS) nanoparticles of Sn_1−x Er _x O₂ (x = 0.0, 0.02, 0.04, and 0.1) were prepared by sol–gel method. The X-ray diffraction patterns showed SnO₂ rutile structure for all samples with no impurity peaks. The decrease in crystallite size with Er concentration was confirmed from TEM measurements (from 12 to 4 nm). The UV–Visible absorption spectra of Er-doped SnO₂ nanoparticles showed blue shift in band gap compared to undoped SnO₂. The electron spin resonance analysis of Er-doped SnO₂ nanoparticles indicate Er³⁺ in a rutile lattice and also decrease in intensity with Er concentration above x = 0.02. Temperature-dependent magnetization studies and the inverse susceptibility curves indicated increased antiferromagnetic interaction with Er concentration.