吸收介质膜/金属空芯光纤的太赫兹波传输特性

介质/金属结构空芯光纤是一种有发展前景的太赫兹波传输媒质.介质膜在有效增加内面反射率从而降低传输损耗的同时,其材料吸收会引起附加损耗.讨论了介质材料吸收对太赫兹空芯光纤结构参数的影响.计算结果表明,相比于无吸收的理想介质,吸收介质的最优膜厚变小.最优折射率变大.综合考虑了光纤内直径、介质膜折射率和传输波长等因素,分析了介质膜的材料吸收容限.分析结果表明,吸收容限随光纤内直径减小或传输波长增大而减小.当光纤内直径很小或传输波长很大时,吸收容限可能不存在.分析结果对介质/金属太赫兹空芯光纤的设计和材料选择具有重要参考价值.     

有限包层半径光纤Bragg光栅的理论研究

采用光纤波导三层模型,对有限包层半径光纤Bragg光栅导模有效折射率的改变进行了理论分析,结果表明:当包层直径小于16μm时,单模光纤Bragg光栅(纤芯直径为8.3μm)的导模有效折射率才开始发生明显变化.在包层外添加外包层,通过改变外包层的折射率可以实现对光栅Bragg反射波长的调谐,同时对不同芯子直径的光栅Bragg波长移动进行了数值计算.在保证光纤归一化频率不变的前提下,芯径越小Bragg波长调谐范围越大,当包层厚度为1μm时,芯径为a＝2.2μm的光栅Bragg波长调谐范围约为3.9μm.     

介质/金属结构太赫兹空芯光纤的传输特性

理论分析了金属、介质/金属结构空芯光纤在THz波段的模式结构和传输特性.金属空芯光纤支持TE11模式,介质/金属空芯光纤的介质膜厚在取最优值时支持HE11模式.对于波长为200μm的太赫兹波,内径为1 mm的两种空芯光纤,TE11和HE11模式的损耗分别为8.4 dB/m和2 dB/m.为优化介质/金属结构宅芯光纤的传输性能,分析了金属和介质材料的光学常数对衰减系数的影响.基于几种已发表的金属在太赫兹波段的光学常数,计算结果表明铝是最好的选择;初步测量结果显示,在各种树脂材料中聚乙烯在THz波段吸收较小,并且其折射率接近介质膜的最优值1.41,为太赫兹波空芯光纤中介质膜材料的理想选择.     

长周期光纤光栅检测混合油的折射率

为了检测柴油煤油混合油的折射率特性,利用耦合模理论分析长周期光纤光栅折射率传感特性,建立长周期光纤光栅中心波长、透射谱峰值损耗与混合油品中柴油含量的关系.结果表明:在混合油中,随着柴油含量的增加,长周期光纤光栅波长发生蓝移,当柴油含量达到使混合油折射率等于包层折射率时,中心波长漂移最大,柴油含量每改变1%,中心波长平均漂移0.622 7nm;柴油含量继续增加,混合油折射率大于包层折射率时,光栅中心波长基本保持不变,但是峰值损耗逐渐增大,带宽减小,之后柴油含量每增加1%,峰值损耗线性增加0.154 6dB.该方法在检测混合燃料各组分含量具有潜在的应用前景.     

缺陷层空心单模Bragg光纤的色散特性

针对空心单模Bragg光纤在1.55μm附近表现出非常大的正色散,研究了包层缺陷层对空心单模Bragg光纤色散的调节作用。利用光学软件FDTD Solutions对缺陷层空心单模Bragg光纤的模式耦合特性进行分析;对比分析普通空心单模Bragg光纤和缺陷层空心单模Bragg光纤的色散曲线;讨论了包层缺陷层结构参数对空心单模Bragg光纤的色散调节作用。     

空芯带隙型光子晶体光纤整体空气孔包层导光特性研究

 传统光纤包层中仅存在泄漏的倏逝波,能量较小,不利于包层传感的应用。增大包层中的能量,实现整体包层导光是提高光纤传感灵敏度的有效途径。从理论上分析了利用空芯带隙型光子晶体光纤(HC-PCF)包层进行导光的机理。在实验上选用带隙外的冷光源和激光对一种典型结构的HC-PCF进行了空气孔包层的导光实验,并利用折射率引导型光子晶体光纤和单模光纤进行对比实验。结果表明,带隙范围外光波在HC-PCF中传输时将不受禁带效应的约束泄露至包层中重新分布。包层中SiO2与空气孔的周期型结构将光波约束在高折射率介质中,实现HC-PCF整体空气孔包层中光波的稳定传输。PBG-PCF包层的整体导光在传感上有提高灵敏度的潜在价值。     

基于对称双环嵌套管的低损耗弱耦合六模空芯负曲率光纤

本文设计了一种具有对称双环嵌套管结构的新型低损耗少模空芯负曲率光纤,该光纤支持LP₀₁, LP₁₁,LP₂₁, LP₀₂, LP_31a, LP_31b共6种纤芯模式.所设计的光纤以SiO₂作为基底材料,采用特殊的对称双环嵌套结构将包层区域进行划分,能够有效地减小纤芯模式与包层模式的耦合.使用有限元法对该少模空芯负曲率光纤的结构参数进行优化,并分析了纤芯各个模式的限制损耗和弯曲损耗.仿真结果表明,所提出的少模空芯负曲率光纤能够同时支持弱耦合的6种纤芯模式独立传输(相邻模式间的有效折射率差均大于10^–4,有效地避免了纤芯内模式间的耦合).在400 nm带宽(1.23—1.63μm,覆盖O, E, S, C, L波段)范围内,纤芯中的6个模式均保持低损耗稳定传输.各模式限制损耗在1.4μm处达到最低,其中基模LP₀₁模式的限制损耗最低,为4.3×10^–7 d B/m.此外,当弯...     

侧边抛磨区材料折射率对光纤光栅波长的影响

针对轮式光纤侧边抛磨法,研究了在侧边抛磨光纤光栅抛磨区覆盖不同折射率的材料时,侧边抛磨光纤光栅Bragg波长随外界折射率的改变而变化的特性.理论计算与实验结果都表明,侧边抛磨光纤光栅Bragg波长会随抛磨区覆盖材料折射率的增大向长波长方向偏移;侧边抛磨面离光栅区纤芯表面越近,覆盖材料折射率对波长偏移的影响越大.实验指出,当侧边抛磨区覆盖材料的折射率从1.389 7变到1.447 9时,Bragg波长将会发生1.402 nm的偏移.用轮式光纤侧边抛磨法制备的侧边抛磨光纤光栅可应用于光纤光栅的波长调谐或传感器.     

空芯光纤中介质层材料色散的研究

提出一种根据实验测量的损耗谱曲线,通过曲线拟合等方法获得空芯光纤巾介质层薄膜材料色散性质的方法,并使用此方法得到了数种空芯光纤中常用的介质层材料在可见光与近红外Ⅸ域的色散柯西公式.将得列的介质层材料色散引入到空芯光纤传输损耗谱的理论计算中之后,相对于小考虑材料色散或者使用文献中提供的色散数据进行计算的结果,理论计算结果能更好地符合实验测量结果,从而能够在理论上更加准确地预估空芯光纤在可见光与近红外区域的低损耗窗口的位置.所获得的材料色散柯西公式对于空芯光纤的高性能化没计有重要的辅助作用.     

包层为负折射率介质的抛物型渐变光纤色散特性分析

研究了纤芯为各向同性非均匀材料,而包层为负折射率均匀介质光纤的色散特性.在纤芯满足弱渐变条件的假定下,按矢量场分析法,通过芯层与包层的介电常数比ξ和磁导率比η,讨论了导波模式色散特性对左手介质包层材料的依赖性.分析表明,ξ和 η对轴对称模色散曲线的低频段影响较大,但对非轴对称模影响不大.ξ和 η对导波模式的截止频率没有影响.由于该光纤中的HEm1模的截止频率都等于0,所以不存在理论上的单模区,但仍可近似实现无色散传输.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.