Efficient and widely step-tunable terahertz generation with a dual-wavelength CO<Subscript>2</Subscript> laser

Coherent terahertz radiation in a widely step-tunable range of 72.3–2706 μm (0.11–4.15 THz) has been generated in GaAs crystal by difference-frequency generation using one CO₂ laser with dual-wavelength output. The peak power of THz pulse reaches 35 W at the wavelength of 236.3 μm, which corresponds to a pulse energy of 2.1 μJ. An average power of 10 μW has been achieved when working repetitively. This efficient terahertz radiation source is more compact and widely tunable than other THz sources pumped by CO₂ laser.     

Synchronously pumped femtosecond optical parametric oscillator based on AgGaSe2 tunable from 2 μm to 8 μm

The operation of a continuous-wave mode-locked silver gallium selenide (AgGaSe₂) optical parametric oscillator (OPO) is reported. The OPO was synchronously excited by 120-fs-long pulses of 1.55-μm radiation at a repetition rate of 82 MHz. The 1.55-μm radiation is generated by a noncritically phasematched cesium-titanyl-arsenate (CTA)-OPO pumped by a mode-locked Ti:sapphire laser. The AgGaSe₂-OPO generates signal and idler radiation in the range from 1.93 μm to 2.49 μm and from 4.1 μm to 7.9 μm, respectively. Up to 67 mW of signal wave output power has been obtained. The experimentally determined pulse duration and chirp parameters are in reasonable agreement with results from a numerical model taking into account group velocity mismatch, group velocity dispersion, self phase modulation, and chirp enhancement. Received: 6 August 1999 / Revised version: 4 October 1999 / Published online: 3 November 1999     

Excimer-laser ablation and micro-patterning of ceramic Si3N4

3 N₄ has been investigated. The ablation threshold in air, Φ_th, is around 0.3±0.1 J/cm² with ArF- and 0.9±0.2 J/cm² with KrF-laser radiation. With fluences Φ_th<Φ<4 J/cm² the irradiated surface is either very flat or it exhibits a cone-type structure, depending on the number of laser pulses employed. With fluences of 5 to 10 J/cm², the sample surface becomes very smooth, much smoother than the original mechanically polished surface. Pores, scratches, and cracks observed on the non-irradiated surface are absent within the illuminated area. In this regime, the ablation rates are typically 0.1 to 0.2 μm/pulse. Received: 10 April 1997/Accepted: 11 April 1997     

Characterization of a Br(2P1/2)–CO2(1001-1000) transfer laser driven by photolysis of iodine monobromide

2 laser operating on the 10⁰1-10⁰0 transition at λ=4.3 μm and pumped by E –V energy transfer from Br(²P_1/2) has been demonstrated. The dynamics and performance of this device were characterized by observing the time-resolved stimulated emission and the steady-state spontaneous side fluorescence after photolysis of IBr or Br₂ by a frequency-doubled Nd:YAG laser or Ar⁺ laser, respectively. Although the E –V excitation kinetics are favorable, rapid vibrational relaxation limits laser action to CO₂ pressures of less than 1 Torr. Numerical modeling of laser pulse shapes and the dependence on IBr and CO₂ pressure and photolysis energy establish a relatively high gain of 0.33%/cm, a CO₂-pressure-dependent optical loss of 0.04–0.06%/cm, and an efficiency of 2×10^-5 4.3-μm-laser photons per incident photolysis photon. The CO₂ fluorescence after photolysis of a fixed Br₂/CO₂ gas mixture decreases as a function of photolysis time by about 30%/h, indicating the photolytic production of an important quencher. Received: 23 June 1997/Revised version: 23 September 1997     

Hard tissue ablation with a free running Er:YAG and a Q-switched CO2 laser: a comparative study

The Er:YAG and the CO₂ laser are competitors in the field of hard tissue ablation. The use of Er:YAG lasers (2.94 μm, pulse length _L of 100 to 200 μs) show smaller areas of thermal defects then ‘‘superpulsed’’ CO₂ lasers with pulse lengths of approximately 100 μs. Only the development of a Q-switched CO₂ laser (9.6 μm, τ_L=250 ns) allowed for similar results. In this paper new results for the Er:YAG and the Q-switched CO₂ laser under the influence of water spray will be presented. Several parameters are of special interest for these investigations: the specific ablation energy, which shows a minimum for the CO₂ laser at an energy density of 9 J/cm ² and a broad shallow minimum in the range of 10 to 70 J/cm² for the Er:YAG laser, and comparison of the cut-shape and depth. Surface effects and cutting velocity are discussed based on SEM pictures. Received: 19 July 2000 / Revised version: 1 November 2000 / Published online: 30 November 2000     

Radio frequency excited waveguide CO2 lasers on sequence-band transitions

2 lasers based on either a quartz or an alumina waveguide were studied on the 00°2 - [10°1,02°1]_I,II sequence bands. A compact multisegment RF excitation with capacitive coupling was used for pumping the gain section of the laser waveguide. The use of a separate intracavity hot CO₂ waveguide suppresses the regular-band transitions. The quartz waveguide laser has a total of 62 lines lasing on both the 9.4 and 10.4 μm sequence bands. The alumina waveguide laser has 40 lines lasing on the 10.4 μm sequence band. These lasers can be either pulsed or continuous-wave (CW) operated on the selected line without a line jumping problem. Received: 29 September 1997/Revised version: 2 December 1997     

Generation of continuously tunable terahertz-wave radiation exploited by stimulated polariton scattering

The characteristics of a coherent tunable terahertz-wave source have been experimentally investigated in detail. By using a difference frequency generation as a result of stimulated Raman scattering by polaritons in MgO:LiNbO₃ crystals, the signal wave was continuously tuned in the range of 1.069–1.075 μm, which corresponded to a terahertz-wave in the wide range from 227 to 104 μm (1.3 to 2.9 THz). The highest output signal pulse energy at the pumping level of 44 mJ/pulse was 1.8 mJ/pulse with 20 mW seeder injection, and the terahertz peak power was 139 mW at the wavelength of 143 μm. This source has the advantages of simple alignment, simplicity of tuning, and compactness that makes the device more attractive.     

Multiwatt optically pumped ammonia laser operation in the 12–13 μm

Design and operating caracteristics of high pulse repetition rate NH₃ laser producing up to 20 W of average output power are described. The NH₃ laser, operating in the 12–13 μm region was optically pumped with a high pulse repetition rate TEA CO₂ laser. Dependences of the NH₃ laser output on the pump energy, ammonia and buffer gas pressures and pulse repetition rate have been studied. The conversion efficiency of up to 16% has been received.     

Near-infrared trace-gas sensors based on room-temperature diode lasers

2 monitor designed for field applications using room-temperature diode lasers are presented. Near-infrared DFB lasers operating at 1.57 μm and around 2.0 μm have been used for CO₂ measurements. At ambient concentration levels a resolution of more than two orders of magnitude has been demonstrated at 1.57 μm, at 2 μm the precision is in the order of 0.1 ppm CO₂, and for trace analysis a detection limit of 10 ppb has been obtained. The measurements demonstrate the capability of near-infrared DFB diode lasers for the precise determination of CO₂ concentrations as required for climatological, medical, or industrial applications. Received: 24 February 1998/Revised version: 27 April 1998     

Development of a microstrip-based neutron detector

A gas-filled microstrip detector for thermal neutrons has been built and successfully tested in our laboratory. The detector has an active area of 20 mm × 15 mm and consists of alternate anodes and cathodes of widths 12 μm and 300 μm respectively. The anode to cathode gap is 150 μm and the pitch is 612 μm. A high resistance, meandering type horizontal strip connects the anodes at one end and aids in position sensing by charge division method. The detector is tested with gas mixtures³He+Kr (1: 2) and³He+CF₄ (2:1) at pressure of 3 atmospheres and using a Pu-Be neutron source. The pulse height spectrum shows energy resolution of ∼8% (FWHM) for the 764 keV peak at anode voltage of 525 V for³He+Kr and ∼15% at anode voltage of 800 V for³He+CF₄. Gas gains up to 6.3 × 103 and 3.6 × 103 are obtained respectively with these gas mixtures. The overall efficiency of the detector along the sensitive length is tested by exposing the active area to neutrons and recording the position spectrum. The detector shows fairly uniform efficiency (∼45%) over the active length.     

CW laser performance of Yb and Er,Yb doped tungstates

 Room temperature cw laser action of Yb³⁺-doped KY(WO₄)₂ and KGd(WO₄)₂ crystals at 1.025 μm and Er, Yb : KY(WO₄)₂ at 1.54 μm has been demonstrated under pumping by both Ti-sapphire laser and InGaAs laser diodes. A slope efficiency of Yb-lasers up to 78% has been obtained. Received: 19 June 1996     

High repetition rate LiF<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack>: Color center laser

The efficient oscillation of LiF:F₂⁻ color center laser pumped by a compact LD-pumped Nd:YVO₄ acousto optically Q-switched laser with 30 kHz pulse repetition rate was demonstrated. The broadband oscillation with 75 μJ pulse energy and 37 kW peak power with the slope efficiency 20% was obtained. The average output power as high as 230 mW was reached. The narrow line tunable from 1.10 to 1.29 μm laser radiation with 10% conversion efficiency in the maximum of the tuning curve was achieved under pumping with 1.6 W average pump power.     

Validity of the three-charge-state model in photorefractive BaTiO3:Rh at 1.06 μm in the cw regime

3 :Rh are the only ones involved in the photorefractive effect at 1.06 μm. In this paper, we apply this model to the prediction of the steady-state photorefractive space-charge field. We present experimental measurements of induced absorption and beam-coupling gain in BaTiO₃:Rh at 1.06 μm, which are consistent with the model. From these data, we determine a set of parameters (with error bars) such as the excitation cross sections and density of rhodium. Received: 2 January 1997 / Revised version: 21 March 1997     

A Raman laser system for multi-wavelength satellite laser ranging

~~A Raman laser system for multi-wavelength satellite laser ranging@K.Hamal$Czech Technical University in Prague,Czech @I.Prochazka$Czech Technical University in Prague,Czech @J.Blazej$Czech Technical University in Prague,Czech1. Yang Fumin, Chen Wanzhen, Zhang Zhongping et al., Satellite laser ranging experiment with sub-centimeter single-shot ranging precision at Shanghai Observatory, Science in China, Ser. A, 2002, 32(10): 935-939. 2. Degnan, J. J., Millimeter accurac…     

Generation of subpicosecond infrared pulses tunable between 5.2 μm and 18 μm at a repetition rate of 76 MHz

2 (2 mm thick) and GaSe (1 mm thick) crystals are applied as nonlinear media. GaSe has a larger tuning range and is more efficient in the whole spectral range than AgGaS₂. The average IR power reaches up to 2.0 mW at 8.5 μm when the GaSe crystal is used, and up to 1.3 mW at the same wavelength when AgGaS₂ is applied for the frequency conversion. Received: 17 February 1997/Revised version: 14 July 1997     

Optical parametric oscillators for high pulse energy and high average power operation based on large aperture periodically poled KTP and RTA

We report on optical parametric oscillators (OPOs) based on large aperture periodically poled KTiOPO₄ (PPKTP) and RbTiOAsO₄ (PPRTA) pumped with high pulse energy and high average power Q-switched solid-state lasers. The OPOs were pumped with 1064-nm pulses of a diode-pumped Nd:YVO₄ laser at 20 kHz repetition rate. The emitted signal wavelengths were 1.72 μm and 1.58 μm and the idler wavelengths were 2.79 μm and 3.26 μm, respectively. Pumping the PPKTP OPO with 7.2 W and the PPRTA OPO with 8 W average power, 2 W and 1.3 W total OPO output powers were generated. Two-dimensional measurements of the total OPO output power, the signal wavelength and the signal bandwidth in dependence on the crystal location indicated a good uniformity of the quasiphasematching structure over the entire 3-mm-thick crystals. This allowed pumping with larger pump beams and therefore with pulse energies of tens of millijoules. Pumping with different flash-lamp-pumped lasers, good OPO performance and high output pulse energies could be achieved for all pump lasers. Maximum input pulse energies of 56 mJ gave output pulse energies of as much as 18 mJ. The temperature tuning behaviors of both OPOs were measured, showing excellent agreement with calculated temperature tuning curves. New equations for temperature dispersion in RTA are presented. These results show that large-aperture PPKTP and PPRTA crystals are well suited for tunable nanosecond OPO operation with multi-watt average pump power and several tens of millijoules pump pulse energies. Received: 7 September 2001 / Published online: 7 November 2001     

Mid-infrared ZGP OPO pumped by near-degenerate narrowband type-I PPKTP parametric oscillator

The total pulse energy of the signal and idler in a near-degenerate type-I periodically poled KTiOPO₄ (PPKTP) optical parametrical oscillator (OPO) was spectrally confined within a 2 nm spectral bandwidth at 2.13 μm. This was achieved by using a volume Bragg grating as the output coupler. Both the signal and the idler from the PPKTP OPO were then simultaneously used to pump a mid-infrared ZnGeP₂ (ZGP) OPO. The 2 nm bandwidth was narrower than the ZGP crystal acceptance bandwidth and, thus, made efficient conversion in the second OPO possible. A total slope efficiency of 10% from 1.06 μm to the 3.5–5 μm region was demonstrated, generating 250 μJ in the mid-IR with only 3.6 mJ of 1.06 μm pump energy. This corresponds to a Nd:YAG pump to mid-IR conversion efficiency of 7%. PACS 42.65.Yj; 42.72.Ai; 42.40.Eq     

8.30 μm singly resonant ZnGeP2 optical parametric oscillators pumped by a Tm,Ho:GdVO4 laser

A single resonator 8.30 μm ZnGeP₂ (ZGP) optical parametric oscillators (OPO) was reported in the paper. The OPO was pumped by a 10.2-W Tm,Ho:GdVO₄ laser at 8 kHz in a Q-switch mode, a 170-mW idler was obtained at 8.30 μm, and the output power of the idler and signal wave was 1.0 W, corresponding to an optical-optical conversion efficiency of 10.3% and a slope efficiency of 20.9%. Tm,Ho:GdVO₄ laser was pumped by a 30-W fiber-coupled laser diode (LD) at the center wavelength of 801 nm. The output wavelength of Tm,Ho:GdVO₄ laser was at 2.05 μm, and the energy per pulse of 1.28 mJ in 18 ns was achieved at 8 kHz with the peak power of 71.1 kW.     

Dynamic behavior of photoablation products of corneal tissue in the mid-IR: a study with FELIX

2 . Dynamic parameters such as the extension of the ablation cloud, the initial velocity and momentum of the ablated particles as well as the ablation threshold, the ablated mass, and the particle size were investigated. The ablation plume was made visible with a stroboscopic technique. For a fluence of 3.1 J/cm² the average initial velocity of the ejected particles was deduced from the extension of the plume to range from 120–400 m/s. Measurements of the recoil momentum using a sensitive pendulum led to values between 0.5 and 2.0 mm g/s. All measured properties were related to the spectroscopically determined absorption coefficient of cornea α_cornea. Where absorption due to proteins is high (at λ=6.2 and 6.5 μm), ablated mass, velocity and recoil momentum behave according to α_cornea. For the first time, variations of the ablation plume from pulse to pulse were observed. Those, as well as the particle size, not only depend on the absorption coefficient, but also on the predominant absorber. Received: 4 November 1997/Revised version: 7 September 1998     

High-power picosecond LiB3O5 optical parametric oscillators tunable in the blue spectral range

The paper reports on an experimental investigation and numerical analysis of noncritically and critically phasematched LiB₃O₅ (LBO) optical parametric oscillators (OPOs) synchronously pumped by the third harmonic of a cw diode-pumped mode-locked Nd:YVO₄ oscillator–amplifier system. The laser system generates 9.0 W of 355-nm mode-locked radiation with a pulse duration of 7.5 ps and a repetition rate of 84 MHz. The LBO OPO, synchronously pumped by the 355-nm pulses, generates a signal wave tunable in the blue spectral range 457–479 nm. With a power of up to 5.0 W at 462 nm and 1.7 W at 1535 nm the conversion efficiency is 74%. The OPO is characterized experimentally by measuring the output power (and its dependence on the pump power, the transmission of the output coupler and the resonator length) and the pulse properties (such as pulse duration and spectral width). Also the beam quality of the resonant and nonresonant waves is investigated. The measured results are compared with the predictions of a numerical analysis for Gaussian laser and OPO beams. In addition to the blue-signal output visible-red 629-nm radiation is generated by sum-frequency mixing of the 1.535-μm infrared idler wave with the residual 1.064-μm laser radiation. A power of 1.25 W of 1.535-μm idler radiation and 5.7 W of 1.064-μm laser light generated a red 629-nm output power of 2.25 W. Received: 2 February 2000 / Revised version: 28 July 2000 / Published online: 22 November 2000