Robust isocratic liquid chromatographic separation of functional poly(methyl methacrylate)

The separation of telechelic poly(methyl methacrylate) (PMMA) prepolymers based on the number of end-groups under critical liquid chromatography (LC) conditions has been studied using a bare-silica column, which can interact with polar functional groups. The critical solvent compositions for non-functional, mono-functional and bi-functional PMMAs were determined in normal-phase LC using mixtures of acetonitrile and dichloromethane (DCM) of varying composition as the mobile phase. The telechelic prepolymers were successfully separated according to hydroxyl (OH) functionality (with zero, one, or two OH groups, respectively) under the critical conditions, in which fast (5 min), base-line separations were obtained independent of molecular weight. Changing the column temperature, flow rate, and mobile-phase composition within a certain range did not affect the functionality separation. Therefore this isocratic LC separation method is quite robust. Evaporative light-scattering detector (ELSD) calibration curves were used for the quantitative analysis of functional PMMA prepolymers.     

Characterization of branched ultrahigh molar mass polymers by asymmetrical flow field-flow fractionation and size exclusion chromatography

The molar mass distribution (MMD) of synthetic polymers is frequently analyzed by size exclusion chromatography (SEC) coupled to multi angle light scattering (MALS) detection. For ultrahigh molar mass (UHM) or branched polymers this method is not sufficient, because shear degradation and abnormal elution effects falsify the calculated molar mass distribution and information on branching. High temperatures above 130 °C have to be applied for dissolution and separation of semi-crystalline materials like polyolefins which requires special hardware setups. Asymmetrical flow field-flow fractionation (AF4) offers the possibility to overcome some of the main problems of SEC due to the absence of an obstructing porous stationary phase. The SEC-separation mainly depends on the pore size distribution of the used column set. The analyte molecules can enter the pores of the stationary phase in dependence on their hydrodynamic volume. The archived separation is a result of the retention time of the analyte species inside SEC-column which depends on the accessibility of the pores, the residence time inside the pores and the diffusion ability of the analyte molecules. The elution order in SEC is typically from low to high hydrodynamic volume. On the contrary AF4 separates according to the diffusion coefficient of the analyte molecules as long as the chosen conditions support the normal FFF-separation mechanism. The separation takes place in an empty channel and is caused by a cross-flow field perpendicular to the solvent flow. The analyte molecules will arrange in different channel heights depending on the diffusion coefficients. The parabolic-shaped flow profile inside the channel leads to different elution velocities. The species with low hydrodynamic volume will elute first while the species with high hydrodynamic volume elute later. The AF4 can be performed at ambient or high temperature (AT-/HT-AF4). We have analyzed one low molar mass polyethylene sample and a number of narrow distributed polystyrene standards as reference materials with known structure by AT/HT-SEC and AT/HT-AF4. Low density polyethylenes as well as polypropylene and polybutadiene, containing high degrees of branching and high molar masses, have been analyzed with both methods. As in SEC the relationship between the radius of gyration (R(g)) or the molar mass and the elution volume is curved up towards high elution volumes, a correct calculation of the MMD and the molar mass average or branching ratio is not possible using the data from the SEC measurements. In contrast to SEC, AF4 allows the precise determination of the MMD, the molar mass averages as well as the degree of branching because the molar mass vs. elution volume curve and the conformation plot is not falsified in this technique. In addition, higher molar masses can be detected using HT-AF4 due to the absence of significant shear degradation in the channel. As a result the average molar masses obtained from AF4 are higher compared to SEC. The analysis time in AF4 is comparable to that of SEC but the adjustable cross-flow program allows the user to influence the separation efficiency which is not possible in SEC without a costly change of the whole column combination.     

Separation and characterization of functional poly(n-butyl acrylate) by critical liquid chromatography

The separation of functional poly(n-butyl acrylate) (PnBA) polymers based on the number of end-groups under critical liquid chromatography (LC) conditions has been studied using a bare-silica column. The (near-) critical solvent compositions for non-, mono-, and difunctional (telechelic) carboxyl-PnBAs were determined in normal-phase LC, using mixtures of acetonitrile, acetic (or formic) acid, and dichloromethane of varying composition. Some formic or acetic acid had to be added to the mobile phase to elute PnBA polymers with carboxyl end-groups. The critical solvent compositions obtained were not exactly the same for non-, mono-, and difunctional PnBA polymers. These were unusual experimental observation, but they were in agreement with theoretic predictions. Nevertheless, low-molecular-mass PnBA samples were successfully separated according to the carboxyl functionality at (near-) critical conditions. With the aid of mass spectrometry (MS), the (near-) critical separation of low-molecular-mass PnBA polymers was confirmed to be mainly based on the carboxyl functionality. Calibration curves for evaporative light-scattering detection (ELSD) were used for quantitative analysis of carboxyl-functional PnBA polymers. The results proved that nearly ideal functionalities (average number of carboxyl end-groups per molecule up to 1.99) were achieved for telechelic PnBAs prepared by one-step reversible addition-fragmentation chain-transfer (RAFT) polymerization of PnBA.     

Molar mass distributions by gradient liquid chromatography: predicting and tailoring selectivity

Interactive liquid chromatography (iLC) for polymer analysis is usually applied to the characterisation of distributions other than molar mass. In particular, its use for the determination of chemical-composition, functionality-type and tacticity distributions has been demonstrated. The application of iLC for the determination of molar mass distributions (MMDs), however, has not yet been fully explored. An expanded version of the reversed-phase liquid chromatography model has been developed to describe and predict how the retention behaviour of polydisperse polystyrene samples changes with molar mass. The relationship between molar mass and the parameters of the model has been investigated in some detail and non-linear correlations were found. From the model and the relationships between the model parameters and molar mass, calibration curves (retention time versus molar mass) were constructed to predict changes in chromatographic selectivity across a given molar mass range. These calibration curves were compared to experimentally obtained curves and, in most cases, excellent agreement was found. The dramatic enhancement in selectivity that can be obtained with iLC in comparison to size-exclusion chromatography (SEC) was illustrated by measuring matrix-assisted laser desorption ionisation (MALDI) MS spectra of fractions collected during a gradient-LC separation. In the low-molar mass range, essentially monodisperse fractions were obtained. Calibration curves, predicted by the model and validated experimentally using narrow-dispersity standards and MALDI-MS spectra of fractions, were used to determine the molar mass distribution of some narrowly distributed polystyrene samples. Molar mass distributions for such standards were found to be somewhat lower than the values reported by the manufacturers. The results also deviated from those obtained by MALDI-MS.     

Enthalpy assisted size exclusion chromatography. Part 2. Adsorption retention mechanism

A novel high performance liquid chromatographic method for separation of synthetic polymers has been tested. It involves combination of the enthalpic and entropic retention mechanisms, resulting in increased selectivity of separation within a specific molar mass range. In this present case, the enthalpic retention mechanism is adsorption of macromolecules on a bare silica gel column packing. Under critical conditions of enthalpic interactions, homopolymers are known to elute irrespective of their molar mass. However, in the vicinity of critical conditions, a situation can be identified when retention volumes (V(R)) rapidly decrease with increasing molar mass. Typically, this happens for polymer species close to or above their exclusion limit observed with the same column in the absence of enthalpic interactions between macromolecules and packing, that is near "ideal SEC" conditions. The dependence of polymer retention volume on molar mass closely resembles size exclusion conditions. However, the witnessed rate of change in V(R )with polymer molar mass is more pronounced, thus indicating increased selectivity of separation. This situation not only offers the benefit of more selective separation according to molar mass but efficient discrimination of macromolecules possessing different nature and interactivity with the column packing can be accomplished as well.     

Studies on high-performance size-exclusion chromatography of synthetic polymers. I. Volume of silica gel column packing pores reduced by retained macromolecules

Macromolecules, which stay adsorbed within the active size-exclusion chromatography (SEC) column packings may strongly reduce effective volume of the separation pores. This brings about a decrease of retention volumes of the non-retained polymer samples and results in the increased apparent molar mass values. The phenomenon has been demonstrated with a series of poly(methyl methacrylate)s (PMMA) and a polyethylenoxide (PEO) fully retained by adsorption within macroporous silica gel SEC column from toluene or tetrahydrofuran, respectively. The non-retained probes were polystyrenes (PS) in toluene and both PS and PMMA in THF eluents. The errors in the peak molar mass values determined for the non-retained polymer species using a column saturated with adsorbed macromolecules and considering calibration curves monitored for the original "bare" column packing assumed up to several hundreds of percent. Errors may appear also in the weight and number averages of molar masses calculated from calibration dependences obtained with columns saturated with adsorbed macromolecules. Moreover, the SEC peaks of species eluted from the polymer saturated columns were broadened and in some cases even split. These results demonstrate a necessity not only to periodically re-calibrate the SEC columns but also to remove macromolecules adsorbed within packing in the course of analyses.     

Liquid chromatography of polymers under limiting conditions of desorption II. Tandem injection and quantitative molar mass determination

Liquid chromatography under limiting conditions of desorption (LC LCD) is a method which allows molar mass independent elution of various synthetic polymers. A narrow, slowly moving zone of small molecules, which promotes full adsorption of one kind of polymer species within column (an adsorli) acts as an impermeable barrier for the fast moving macromolecules. The latter accumulate on the barrier edge and elute nearly in total volume of liquid within column. At the same time, transport of less adsorptive macromolecules is not hampered so that these are eluted in the size exclusion (SEC) mode. As result, polymers differing in their polarity and adsorptivity can be easily separated without molar mass interference. Three methods of barrier creation are discussed and compared. It is shown that a fraction of sample may elute unretained if the adsorli sample solvent is used as a barrier in connection with a narrow-pore column packing. One part of excluded macromolecules likely breaks-out from the adsorli zone and this results in partial loss of sample and distortion of the LC LCD peaks. This problem can be avoided if the adsorli zone is injected immediately before sample solution. Applicability of the LC LCD method for polymer separation has been demonstrated with a model mixture of poly(methyl methacrylate) (adsorbing polymer) and polystyrene (non adsorbing polymer) using bare silica gel as a column packing with a combination of tetrahydrofuran (a desorption promoting liquid -a desorli) and toluene (adsorli). It has been shown that the LC LCD procedure with tandem injection allows simple and fast discrimination of polymer blend components with good repeatability and high sample recovery. For quantitative determination of molar masses of both LC LCD and SEC eluted polymers, an additional size exclusion chromatographic column can be applied either in a conventional way or in combination with a multi-angle light scattering detector. A single eluent is used in the latter column, which separates the mixed mobile phase, system peaks and the desorli zone from the polymer peaks so that measurements are free from disturbances caused by the changing eluent composition. The resulting LC LCD x SEC procedure has been successfully applied to poly(methyl methacrylate) samples.     

The measurement of mass and size distributions,conformation, and branching of important food polymers by mals following sample fractionation

Three distinctive food polymers (ultra high molar mass amylopectin, guar gum, and hemi-cellulose) were chosen as model samples to illustrate the use of multi angle light scattering (MALS) detection in conjunction with size exclusion chromatography (SEC) separations for the characterization of such macromolecules. By combining SEC and MALS, absolute molar mass, rms radius and their distributions can be measured readily without reference to any molar mass standards and without the need to make structural assumptions. In addition, the conformation and branching of those polymers can be derived also.     

Distribution analysis of ultra-high molecular mass poly(ethylene oxide) containing silica particles by size-exclusion chromatography with dual light-scattering and refractometric detection

Two different size-exclusion chromatography (SEC) systems, connected in-line either to a low-angle light scattering (LALS) or to a multiangle light scattering (MALS) detector, are employed for determination of molecular mass distributions (MMD) of poly(ethylene oxide) (PEO) samples having a weight average molecular mass up to eight millions. The detrimental effect of the presence of strongly scattering silica particles in the samples on the light scattering signal can be eliminated using a suitable sample dissolution procedure utilizing silica solubility in aqueous mobile phase. The selection of flow-rate and sample concentration have a large impact on the obtained results. Hydrodynamic retardation phenomena and nonlinearity effects are shown to introduce severe errors in the molecular mass distributions unless flow-rate and sample concentration are kept at sufficiently low levels. Self-compensating ability of the dual detection in flow-rate effects is shown to be the main advantage here. A good agreement between the results obtained using LALS and MALS detection is found provided that a carefully selected angular extrapolation procedure is used in the case of MALS data. Thus, using carefully selected experimental conditions, SEC with light-scattering (LS) and refractometric detection proved to be an efficient technique for MMD characterisation also of ultra-high molecular mass (UHM) PEO polymers.     

Size exclusion chromatography-gradients, an alternative approach to polymer gradient chromatography: 2. Separation of poly(meth)acrylates using a size exclusion chromatography-solvent/non-solvent gradient

A gradient ranging from methanol to tetrahydrofuran (THF) was applied to a series of poly(methyl methacrylate) (PMMA) standards, using the recently developed concept of SEC-gradients. Contrasting to conventional gradients the samples eluted before the solvent, i.e. within the elution range typical for separations by SEC, however, the high molar mass PMMAs were retarded as compared to experiments on the same column using pure THF as the eluent. The molar mass dependence on retention volume showed a complex behaviour with a nearly molar mass independent elution for high molar masses. This molar mass dependence was explained in terms of solubility and size exclusion effects. The solubility based SEC-gradient was proven to be useful to separate PMMA and poly(n-butyl crylate) (PnBuA) from a poly(t-butyl crylate) (PtBuA) sample. These samples could be separated neither by SEC in THF, due to their very similar hydrodynamic volumes, nor by an SEC-gradient at adsorbing conditions, due to a too low selectivity. The example shows that SEC-gradients can be applied not only in adsorption/desorption mode, but also in precipitation/dissolution mode without risking blocking capillaries or breakthrough peaks. Thus, the new approach is a valuable alternative to conventional gradient chromatography.     

Determining the absolute, chemical-heterogeneity-corrected molar mass averages, distribution, and solution conformation of random copolymers

We present a method by which to obtain the absolute, chemical-heterogeneity-corrected molar mass (M) averages and distributions of copolymers and apply the method to a gradient random copolymer of styrene and methyl methacrylate in which the styrene percentage decreases from approximately 30% to 19% as a function of increasing molar mass. The method consists of separation by size-exclusion chromatography (SEC) with detection using multi-angle static light scattering (MALS), differential viscometry (VISC), differential refractometry (DRI), and ultraviolet absorption spectroscopy (UV) and relies on the preferential absorption of styrene over methyl methacrylate at 260 nm. Using this quadruple-detector SEC/MALS/UV/VISC/DRI approach, the percentage of styrene (%St) in each elution slice is determined. This %St is then used to determine the specific refractive index increment, corrected for chemical composition, at each elution slice, which is then used to obtain the molar mass at each slice, corrected for chemical composition. From this corrected molar mass and from the chemical-composition-corrected refractometer response, the absolute, chemical-heterogeneity-corrected molar mass averages and distribution of the copolymer are calculated. The corrected molar mass and intrinsic viscosity at each SEC elution slice are used to construct a chemical-heterogeneity-corrected Mark–Houwink plot. The slice-wise-corrected M data are used, in conjunction with the MALS-determined R _G,z of each slice, to construct a conformation plot corrected for chemical heterogeneity. The corrected molar mass distribution (MMD) of the gradient copolymer extends over an approximately 30,000 g/mol wider range than the uncorrected MMD. Additionally, correction of the Mark–Houwink and conformation plots for the effects of chemical heterogeneity shows that the copolymer adopts a more compact conformation in solution than originally concluded.     

Role of adsorption in liquid chromatography of macromolecules and potential of liquid chromatography in assessing adsorption of macromolecules onto solid surfaces

Many liquid chromatographic (LC) separations of macromolecules are influenced or directly based on adsorption of solutes on column packing. In the case of well known size exclusion chromatography (SEC), adsorption effects are usually unwanted and therefore suppressed. Still they appear in many SEC systems and may badly affect precision of results obtained. In other LC methods applicable to high polymers, adsorption is deliberately combined with exclusion. The aim is to discriminate complex polymer systems which exhibit more than one single distribution of their molecular characteristics. The main goals of such combinations include either a controlled increase or a full suppression of separation selectivity according to one molecular characteristics. Most important so far known exclusion-adsorption compensation methods allowing to suppress dependence of LC retention volumes on polymer molar mass are reviewed. The discussion is accomplished with a presentation of newly developed full adsorption - desorption (FAD) method which can be combined with various LC procedures. A very useful combination represents the on-line FAD/SEC procedure which enables also to study adsorption and desorption phenomena in the systems solid surface - solvent - macromolecules.     

The size exclusion chromatography calibration of ‘Mixed-A’ and ‘Mixed-D’ columns using various polymers and compounds: An application to coal-derived materials

This work attempts to obtain the calibration curves of two different size exclusion chromatography (SEC) columns operating with 1-methyl-2-pyrrolidinone (NMP) as eluent by using various standards. Polystyrene (PS) and polymethylmethacrylate (PMMA) standards were used for obtaining calibration curves, and checked against polysaccharide (PSAC) standards, some small aromatic polycyclic standards and miscellaneous polymers. Polystyrenes and polymethylmethacrylates gave identical calibrations while polysaccharides and miscellaneous polymers lay within 1 or 2 min of the polystyrene calibration. Small molecules of mass less than 1000 units lay on or near to the polystyrene calibration lines, with a shift to late elution for the smallest molecules. This shift may be caused by the interaction with the column packing. A sample has been examined by analytical size exclusion chromatography, which was calibrated using polystyrene and polymethylmethacrylate standards. Molecular mass (MM) distributions of the sample have been examined in terms of these calibrations.     

Characterization of EO-PO Block Copolymers by Liquid Chromatography Under Critical Conditions

Summary: Block copolymers of ethylene oxide (EO) and propylene oxide (PO) are characterized by liquid chromatography under critical conditions (LCCC) for EO. At the critical adsorption point (CAP) for one structural unit, the non-critical block can elute in size exclusion (SEC) or adsorption (LAC) mode. Depending on the molar mass and architecture of the polymers, different strategies are applied. For samples with a higher molar mass, the SEC separation is the method of choice, while lower molar masses also allow a LAC separation. Examples for both situations are given, which show, that these approaches yield different information. In the SEC mode, homopolymers and diblocks can be separated from the triblocks. In LAC mode, a baseline resolution of individual oligomers can be achieved, in which homopolymers, diblocks and triblocks with the same number of repeat units of the non-critical block have the same elution volume.     

Determination of chemical composition distributions in synthetic polymers

A characteristic feature of synthetic polymers is their dispersity in molar mass and, in many cases, chemical composition. Since dispersity is highly relevant in relation to polymer properties, ongoing efforts are being put in the development of appropriate analysis methods. In this respect, size-exclusion chromatography (SEC) is well known for the determination of molar mass distributions. Methods for chemical composition distributions are less mature than SEC and mainly include liquid chromatography and mass spectrometry and the combination of these techniques. The term chemical composition distribution is considered broad in this paper, i.e. for the chemical composition distribution of a (co)polymer backbone, for the functionality type distribution of a polymers' functional end groups, for the block length distribution of a block copolymer, for the branching distribution and for the tacticity distribution. In this paper, analysis methods for all types of chemical composition distributions are reviewed. Special attention is paid to practical requirements and common misconceptions that sometimes arise. Applications within the last 5 years are summarized.     

Preferential solvation of poly(methyl methacrylate) and a bisphenol A diglycidyl ether by size-exclusion chromatography

The preferential adsorption coefficient, lambda, of poly(methyl methacrylate), PMMA, in solutions formed by an epoxy resin in tetrahydrofuran (THF), was studied by size-exclusion chromatography (SEC). Only PMMA of lowest molar mass was preferentially solvated by epoxy but at low concentrations of epoxy in the mixture. At higher epoxy content PMMA was preferentially solvated by THF. A simultaneous and competitive solvation between the specific interactions PMMA-epoxy and the self association of epoxy at high concentrations would be the responsible of this inversion point. The more compacted coil of PMMA of higher molecular weights in solution could explain the lack of interaction of these polymers with epoxy. The results also indicated that lambda decreased with the molar mass. This variation has been attributed to the influence of the coil segment density on preferential adsorption.     

Liquid chromatography under limiting conditions of desorption 4 separation of blends containing low-solubility polymers

Low solubility polymers, poly(ethylene terephthalate), PET and poly(butylene terephthalate), PBT were mutually separated at ambient temperature with help of a novel method, liquid chromatography under limiting conditions of desorption, LC LCD. The results demonstrate high selectivity of LC LCD, which enabled discrimination of macromolecules of well similar chemical structure, irrespectively of their molar mass. Above poly(terephthalate)s were also readily base-line separated from the aliphatic biodegradable polyesters poly(l-lactic acid) and poly(butylene adipate). The experimentally feasible LC LCD method produces narrow, focused peaks of polymers eluted behind the adsorption promoting barrier of appropriate liquid. This merit of LC LCD enables discrimination and identification of minor macromolecular constituents of multicomponent polymers and facilitates the application of method as an integral part of two-dimensional liquid chromatography for comprehensive molecular characterization of complex polymer systems.     

Liquid chromatography of macromolecules at the critical adsorption point. II. Role of column packing: Bare silica gel

Liquid chromatography of macromolecules at the critical adsorption point (LC CAP) presents a potentially very powerful method for molecular characterization of complex polymers. However, LC CAP applicability is limited due to various experimental problems. The pore sizes and surface chemistry of the column packings belong to the most important weak points of the method. The LC CAP behavior of poly(methyl methacrylate)s was investigated using bare silica gels of 6, 12, and 100 nm pore sizes and with various amounts of surface silanols. Tetrahydrofuran as the adsorption suppressing liquid and toluene as the adsorption promoting liquid were mixed to form the “nearly critical” eluents. Both pore size and surface chemistry of silica were found to strongly influence the retentive characteristics of the system in the critical adsorption area. Macromolecules that were large enough to be excluded from the packing pores hardly followed the LC CAP rules: their retention volumes changed irregularly with the polymer molar mass and their recovery dropped sharply. The narrow pore silica gel-packed column governed the elution patterns of the whole column set composed of silica gels with different pore sizes. This makes the conventional LC CAP characterization of common polymers with broader molar mass distribution impractical and even not feasible. A hybrid column system was proposed containing narrow pore nonadsorptive column added in series to the meso- and macroporous LC CAP silica gels. This narrow pore column would allow separation of gas, impurities, and system peaks from the polymer peaks. The possible successive changes of the surface of silica gel, e.g., due to formation of silanols by hydrolysis or due to irreversible adsorption of some admixtures from the sample or eluent may make the LC CAP irrepeatable. Pronounced peak broadening was observed in the critical adsorption area and this effect increased strongly with the polymer molar mass. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1363–1371, 1998     

Analysis of polyamides by size exclusion chromatography and laser light scattering

The molar mass analysis of polyamides is complicated due to the fact that only a limited range of solvents can be used and association and aggregation phenomena have to be screened by adding electrolytes to the mobile phase. Optimum SEC behaviour is obtained when hexafluoroisopropanol + 0.05 mol/L potassium trifluoroacetate is used as the mobile phase. The calibration of the SEC system can be conducted in different ways. While a calibration with narrow disperse polymethyl methacrylate standards does not yield accurate molar mass information, the quantification can be done using an “artificial” calibration curve. This calibration curve is obtained by correcting the PMMA calibration curve with polyamide molar mass data from light scattering. The resulting molar mass distributions for different types of polyamides are compared with molar masses that are determined by size exclusion chromatography with a light scattering detector and an excellent correlation is obtained.     

Liquid chromatography of synthetic polymers under critical conditions of enthalpic interactions 4: Sample recovery

Reduced sample recovery is a frequent feature of LC of macromolecules under critical conditions of enthalpic interactions (LC CC). Several methods of assessment of LC CC sample recovery are compared. A novel approach is based on an online combination of the. The LC CC column with a noninteractive SEC column. It provides not only the amount but also the molar mass of the eluted/withheld polymer. The procedure was tested with poly(methyl methacrylate), bare silica gel column packings, and “critical eluent” tetrahydrofuran/toluene. It was shown that macromolecules with higher molar masses were preferentially trapped within the LC CC column packing so that the eluted part of the sample was no longer representative. The incomplete polymer elution can make the LC CC polymer analyses susceptible to significant experimental errors.