PANI‐PAN coaxial nanofibers have been prepared by electro‐spinning during polymerization. The surface of the resulting nanofibers is superhydrophobic with a water contact angle up to 164.5°. Conductivity of the PANI‐PAN nanofibers is about 4.3 × 10−2 S · cm−1. The superhydrophobic nanofibers show a chemical dual‐responsive surface wettability, which can be easily triggered by changing pH value or redox properties of the solution. A reversible conversion between superhydrophobicity and superhydrophilicity can be performed in a short time. The strategy used here may provide an easy method to control the wettability of smart surfaces by using properties of low‐cost functional polymers.
Two poly(p‐phenylenevinylene) derivative alternating copolymers ( P1‐I and P2‐I ) have been prepared featuring iodo substituents and m‐phenylene units to periodically disrupt conjugation. P1‐I was derivatized with various chromophores to yield P1a‐f . In P1a‐f , the chromophores were positioned within a sterically protected pocket shielding them from interchain interactions so that intrachain interactions between polymer segments could be observed. Solution and film properties of polymers have been examined. Post‐polymerization chromophore modification leads to new photophysical properties such as intramolecular charge transfer and fluorescent resonance energy transfer processes in some cases.
Summary: Poly(propylene oxide)‐amidoacids were used to intercalate montmorillonite clay to afford organoclays with an X‐ray basal spacing as wide as 81 Å. Differing from the ionic exchange between quaternary ammonium salts and the metal ions in clays, the intercalation mechanism involves a beta‐amidoacid chelation with sodium ions in the silicate interlayer confinement. With the end groups tethered on the silicate surface, the hydrophobic poly(propylene oxide)‐backbones self‐aggregate and consequently widen the interlayer space between neighboring silicate plates.
Postulated structure of the chelation of sodium ions by the poly(propylene oxide)‐amido acid. 相似文献
The atom transfer radical polymerization of styrene using activators generated by electron transfer (AGET ATRP) has been carried out in bulk in a limited amount of air at 110 °C, using 1,3,5‐(2′‐bromo‐2′‐methylpropionato)benzene (BMPB) as an initiator and FeCl3 · 6H2O/tris(3,6‐dioxaheptyl) amine (TDA‐1)/ascorbic acid (VC) as a novel FeIII‐mediated catalyst system. The results of the polymerizations demonstrate the features of ‘living’/controlled free‐radical polymerization, such as the number‐average molecular weights being close to their corresponding theoretical values and increasing linearly with monomer conversion, and narrow molecular weight distributions ( = 1.18–1.26). The end functionality of the obtained polymers was confirmed by 1H and 13C NMR spectra as well as a chain‐extension reaction.
A nickel α‐diimine catalyst was used for Grignard metathesis (GRIM) polymerization of 2,5‐dibromo 3‐hexylthiophene and 2‐bromo‐5‐iodo‐3‐hexylthiophene monomers. GRIM polymerization of 2‐bromo‐5‐iodo‐3‐hexylthiophene generated regioregular polymers with molecular weights ranging from 3 000 to 12 000 g · mol−1. The nickel α‐diimine catalyst was also successfully used for the GRIM polymerization of a bulky benzodithiophene monomer.
The main techniques developed to characterize chitosan are recalled. The interaction of chitosan with oppositely charged surfactants was investigated giving very important surface activity effects. A few chemical modifications are described and the new properties obtained are mentioned: alkylation gives amphiphilic polymers having interesting thickening behavior; grafting cyclodextrin (chit‐CD) gives a polymer able to include hydrophobic molecules; grafting adamantane gives an amphiphilic polymer able to specifically interact with chit‐CD forming a temporary network with gel‐like behavior.
The viscosities of adamantane‐chitosan, cyclodextrin‐chitosan, and unmodified chitosan solutions studied here. 相似文献
A novel helical poly(macromonomer) [poly(M‐PS): absolute = 82 800–252 000, determined by GPC/RALLS] with a polyacetylene main chain and polystyrene (PS) side chains was synthesized by the polymerization of acetylene‐terminated M‐PS [ = 2 000, / = 1.20, = 18] with an Rh catalyst. M‐PS was prepared by ATRP of styrene using the acetylene‐containing initiator 2‐bromo‐2‐methylpropionic acid (S)‐1‐methylpropargyl ester ( l ). In solutions, poly(M‐PS) exhibited an intense CD signal at 345–355 nm, indicating that it possessed a predominantly one‐handed helical conformation. Poly(M‐PS) had a stable helical conformation irrespective of solvents and temperature.
Preservation of initial polymer/catalyst particle morphology under air, was examined using stopped‐flow Ziegler–Natta polymerization with various quenching conditions and post‐chemical treatments. The exposure of the initial particles to air caused the fast formation of cracks on the surface, finally leading to significant reformation of the particle shape, when polymerizing particles were washed with heptane at ?65 °C under N2 or under CO2. On the other hand, when the particles were washed with heptane containing an appropriate amount of tetrahydrofuran under CO2, the particle morphology under air was almost completely maintained even after 1 h exposure. The present results are useful for various ex situ characterizations of unstable initial polymer/catalyst particles.
Summary: Magnetic nanoparticles have been prepared by a co‐precipitation method and modified with methacryloxypropyltrimethoxysilane. Magnetic molecularly imprinted polymer particles have been prepared by suspension polymerization in silicone oil. The particles possess a high affinity to the template molecules and are rapidly separated under a magnetic field.
Dispersion polymerization of n‐butyl acrylate has been performed in a mixture of ethanol and water in the presence of poly(N‐acryloylmorpholine) (polyNAM). These hydrophilic polymer chains are synthesized by the RAFT process and thus incorporate well‐defined chain ends. The dithioester ω‐end group is used as an efficient chain transfer agent under dispersion polymerization conditions to produce hairy poly(n‐butyl acrylate) latex particles. Moreover, pre‐functionalization of the polyNAM chains on the α‐end by a carbohydrate derivative is also achieved to obtain directly functionalized particles according to the same strategy.
The synthesis of new star‐shaped polymers, prepared by atom transfer radical polymerization of methyl methacrylate with tris(dialkylaminostyryl‐2,2′‐bipyridine) zinc(II) and iron(II) metalloinitiators, is reported. Their thermal and optical (absorption and emission) properties are discussed.
Twin polymerization is a novel technique for synthesizing hybrid polymers with domain sizes in the nanometer range. While a broad variety of monomers have been investigated, the mechanistic details and the most important influences on the nanostructure formation are unknown. A scale bridging approach is presented to simulate the twin polymerization of 2,2'‐spirobi[4H‐1,3,2‐benzodioxasiline]. This approach is based on detailed quantum chemical calculations that yield insight into reactivity and structure at the molecular level while the kinetics of the network formation process and the influences that govern structure formation are investigated at the mesoscopic level by a coarse‐grained simulation.
Reactions between the ethylene groups in the backbone of conjugated polymers under UV illumination and heat treatment result in the cross‐linking of the main polymer chains. The cross‐linking leads to two simultaneous results in the polymer: excellent solvent resistance and increased bandgap. Using this reaction, three‐color polymer light‐emitting diodes (PLEDs) with a multi‐layer structure can be easily realized by a dry photo‐pattern in an active‐gas‐free environment. Multi‐layer blue devices with dramatically enhanced efficiency can also be achieved conveniently.
Summary: The microwave (MW)‐assisted lipase‐catalyzed ring‐opening polymerization of ε‐caprolactone in boiling solvents was investigated for the first time. In case of boiling toluene or benzene the MW‐assisted reaction proceeded significantly slower compared to oil bath heating. On the other hand, using boiling diethyl ether as solvent, an increase of the polymerization rate due to MW irradiation was found. Yield, molecular weight measurements, and MALDI‐TOF analysis supported the results.
Reactivity of the MW‐assisted ring‐opening polymerization of ε‐caprolactone compared with conventional thermal heating in different solvents. 相似文献
A new approach for the synthesis of polyaniline (PANI) nanostructures under UV light illumination has been developed, which is the first report of a templateless chemical process for preparing pure PANI nanowires. The acceleration effect of photo‐assistance on the polymerization can promote the homogeneous nucleation and elongation of the nanofibers and nanowires, leading to easy preparation of tunable diameters of the nanowires and nanofibers of PANI.
Well‐defined diblock condensation copolymers composed of an aromatic polyamide and an aromatic polyether have been synthesized by means of successive chain‐growth condensation polymerizations. Polymerization of a polyamide monomer with an orthogonally difunctional initiator is accompanied with side reactions. On the other hand, polymerization with a monofunctional initiator afforded well‐defined polyamide, which has been converted into a macroinitiator by introduction of a terminal 4‐fluorobenzophenone unit. Well‐defined diblock copolymers are obtained by polymerization of a polyether monomer in the presence of this macroinitiator.
Carbon black (CB) nanoparticles were encapsulated by poly(vinyl alcohol) (PVA) by a simple method of coacervation. Transmission electron microscopy (TEM) images clearly demonstrated that the successful encapsulation of PVA happened at the surfaces of CB nanoparticles. The particle‐size distribution measurements indicated that the diameters of the obtained PVA‐encapsulated CB (CB@PVA) nanoparticles were distributed within the nanoscale dimension. This strategy avoids the complicated polymerization process involved in the counterpart of polymer‐coating approaches.
A TEM image of PVA‐encapsulated carbon black. 相似文献
Bis(2,2′:6′,2″‐terpyrid‐4′‐yl) diethylene glycol was synthesized as a monomer unit and further utilized for polymerization with FeCl2 in order to form water‐soluble coordination polymers. Viscosity measurements and film‐forming properties indicate the formation of linear coordination polymers or larger ring structures. The terpyridine/iron(II) complexes are stable up to temperatures of 210 °C, but can be uncomplexed by the addition of an excess of a strong competitive ligand (HEDTA) under mild conditions.
Suitably activated, (Cp*){N(tBu)C(Me)N(Et)}ZrMe2 is known to initiate the ‘living’ and isotactic‐selective polymerization of alk‐1‐enes, and it can be used to synthesize block copolymers and stereoblock polymers. We report a full molecular kinetic investigation of propene, but‐1‐ene, and hex‐1‐ene polymerization with a MAO‐activated catalyst system. By combining NMR microstructural polymer analysis with QM modeling of the active species, the complicated regio‐ and stereochemistry of the polyinsertion process, as well as the active chain‐transfer pathways, are investigated. The perspectives and limitations of this catalyst for application in (stereo)block polymerizations are discussed.
Supramolecular self‐assembly of block copolymers in aqueous solution has received ever‐increasing interest over the past few decades due to diverse biological and technological applications in drug delivery, imaging, sensing and catalysis. In addition to relative block lengths, molecular weights and solution conditions, chain architectures of block copolymers can also dramatically affect their self‐assembling properties in selective solvents. This feature article mainly focuses on recent developments in the field of supramolecular self‐assembly of amphiphilic and double hydrophilic block copolymers (DHBCs) possessing nonlinear chain topologies, including miktoarm star polymers, dendritic–linear block copolymers, cyclic block copolymers and comb‐shaped copolymer brushes.