胶束增强型聚电解质微胶囊的制备

采用杂化碳酸钙微球作为模板, 利用LbL技术, 选择聚苯乙烯磺酸钠(PSS), 烯丙基胺的盐酸盐(PAH)和二烯丙基二甲基胺盐酸盐(PADA)聚电解质, 分别组装了PAH/PSS(弱/强)聚电解质胶囊和PADA/PSS(强/强)聚电解质微胶囊. 除去模板后得到了球形良好、分散均匀的聚电解质微胶囊. 研究结果表明, 利用杂化碳酸钙微球作为聚电解质微胶囊的模板, 得到的微胶囊的囊壁厚而致密, 同时, 由于组装采用的聚电解质的种类不同, 囊壁的微观形貌有较大差异.     

静电层层自组装制备聚苯乙烯微球(核)/MCM-41纳米粒子(壳)阶层结构复合微粒

采用聚苯乙烯磺酸钠(PSS)和聚二烯丙基二甲基氯化铵(PDDA)两种聚电解质, 通过静电层层自组装成功地将MCM-41介孔二氧化硅纳米粒子包覆到聚苯乙烯(PS)微球表面. 实验结果表明, 当以尺寸为1.4 μm的PS微球为核时, 包覆了两个聚电解质双层(PDDA/PSS)2的PS(PDDA/PSS)2(PDDA/MCM-41)复合结构微粒与包覆了一个聚电解质双层(PDDA/PSS)的PS(PDDA/PSS)(PDDA/MCM-41)复合结构微粒相比, 复合结构微粒之间的交联程度降低, 但是MCM-41纳米粒子在聚苯乙烯微球表面的包覆都比较松散, 且产物中存在大量杂质. 而当以尺寸为5 μm的聚苯乙烯微球为核时, MCM-41纳米粒子紧密地包覆在聚苯乙烯微球表面, 复合结构微粒之间只有少量桥连物, 且产物中杂质很少.     

富勒醇与阳离子聚电解质复合薄膜的制备与表征

采用静电自组装技术制备了富勒醇与聚对亚苯亚乙烯基 (PPV)的前驱体、聚二烯丙基二甲基氯化铵(PDDA)的复合薄膜 ,利用紫外 可见光吸收光谱 (UV Vis)、原子力显微镜 (AFM )、透射电镜 (TEM)和X射线光电子能谱 (XPS)对薄膜进行了表征 .UV Vis吸收光谱显示 ,在特定波长下自组装薄膜的吸光度与薄膜的双层数成线性关系 ,组装过程具有一致性与重复性 .AFM图象显示富勒醇组装到基片表面后形成直径为几十到10 0多nm的团簇 .富勒醇溶液过滤后组装薄膜 ,薄膜具有较好的均匀性 ;富勒醇溶液不经过滤 ,直接组装薄膜 ,将在薄膜中引入C6 0 晶粒 .XPS分析结果提示C6 0 被羟基修饰并通过静电吸引机制与阳离子聚电解质组装成膜 .富勒醇与PPV的前驱体、PDDA具有很好的自组装性能 ,膜层间的结合力较强 ,所组装的薄膜具有较高的牢固度 .     

长链DNA在金基底上的固定化和电化学标记

本文提出在金基底上用阳离子聚电解质———聚二烯丙基二甲基胺氯化物 (poly(dial lyldimethylammoniumchloride) ,PDDA)自组装膜固定长链DNA的方法 ,用DiffuseReflectanceIn frared ,XPS和STM技术进行表征 ,并对DNA杂交进行电化学标记     

含乳糖聚电解质靶向微胶囊的层层自组装构筑

设计合成了己二酸乳糖乙烯酯/对苯乙烯磺酸钠共聚物（PLESS）,通过层层自组装技术构筑聚烯丙基胺盐酸盐（PAH）与含乳糖聚电解质PLESS的靶向微胶囊。以紫外-可见吸收光谱监测了PAH与PLESS在平面的石英片进行层层自组装过程,研究了不同实验条件（聚电解质浓度、溶液盐度、盐种类）对PAH/PLESS多层膜自组装的影响;PAH与PLESS在球形碳酸钙微球模板上层层自组装,去除模板后得到层状结构的微胶囊,用透射电镜（TEM）等方法观察其形态形貌;通过花生凝集素识别考察其潜在靶向性;通过细胞MTT活性试验评价其生物相容性。     

聚电解质PDDA/PSS层层自组装膜的渗透汽化性能

采用聚电解质层层自组装(LbL)技术, 在不同盐浓度下制备了聚(二烯丙基二甲基氯化铵)/聚苯乙烯磺酸钠(PDDA/PSS) 多层自组装膜, 并用于渗透汽化性能的研究. 重点考察了组装溶液中NaCl的浓度、组装层数及操作温度对自组装膜的异丙醇脱水性能的影响. 同时, 用扫描电镜观测了不同条件下制备膜的表面形貌. 结果表明, 在高NaCl含量的聚电解质溶液中只需组装几个双层的LbL膜, 即能获得较高的分离因子和较大的通量, 并解释了该LbL膜呈现反“trade-off”现象的原因.     

PDDA/SnTsPc静电自组装膜的制备及其形态研究

采用静电层-层自组装技术制备出了含有阴离子磺化酞菁锡(SnTsPc)和阳离子聚二烯丙基二甲基胺盐酸盐(PDDA)交替复合超薄膜.利用紫外-可见光谱表征了PDDA/SnTsPc多层膜的组装过程,表明薄膜的吸收是连续的、有规律的.原子力结果表明,膜表面是光滑的、均匀的;在膜表面紧密堆积的纳米粒子的平均粒径为53.1 nm,平均表面粗糙度是4.021 nm.     

原位凝聚法制备聚电解质微胶囊——模板中掺杂聚电解质量对微胶囊结构与性能的影响

通过在CaCO3制备过程中加入不同浓度聚苯乙烯磺酸钠(PSS)的方法来控制掺杂进CaCO3粒子中的PSS含量,得到了PSS掺杂量为4%～11%,尺寸均匀的CaCO3球形微粒.在微粒表面仅吸附一层聚烯丙基胺盐酸盐(PAH)后,用乙二胺四乙酸二钠(EDTA)使碳酸钙溶解;释放出的PSS与PAH原位凝聚制备得到了分散良好且完整的聚电解质复合物微胶囊.在所研究的范围内,模板微粒中PSS的含量对微胶囊的形态结构和性能没有明显影响.与传统的层层组装微胶囊相比,聚电解质复合物微胶囊有较好的热稳定性,但在高盐浓度下尺寸收缩程度较大.由于和层层组装微胶囊相比缺乏结合紧密的有序结构,原位凝聚法制备的微胶囊囊壁的截留分子量较大.     

链状Silicalite-1分子筛的合成

在传统的合成体系中, 加入聚电解质聚二烯丙基二甲基胺盐酸盐(PDDA)自组装合成链状的Silicalite-1分子筛材料, 考察了PDDA的加入对产物的影响, 并对其进行了XRD和SEM表征.     

有机分子与聚电解质静电吸附成膜特性研究

选取多种有机分子及聚电解质，采用静电吸附自组装法制备了聚电解质，聚电解质、聚电解质，有机分子、有机分子，有机分子的复合薄膜，讨论了这些体系的静电吸附成膜特性及其成膜机理．     

Direct determination of the thermodynamics of polyelectrolyte complexation and implications thereof for electrostatic layer-by-layer assembly of multilayer films

Interpolyelectrolyte complex (IPEC) formation between poly(styrene sulfonate) (PSS) and poly(allylamine hydrochloride) (PAH) has been studied over a range of ionic strengths by isothermal titration calorimetry (ITC), turbidity titration, and electrostatic layer-by-layer assembly (ELBL). The results indicate that IPEC formation of PSS/PAH in aqueous solution is predominantly entropy-driven. The thermodynamic parameters suggest the formation of different types of complexes and aggregates due to salt-induced conformational changes in the polyelectrolyte conformation. Differences in polyelectrolyte behavior in the different salt-concentration regimes are described in terms of changes in the Debye screening length of the polyelectrolytes. The relationship of the results to the effect of salt concentration on the assembly of polyelectrolyte multilayer films (PEMs) is discussed.     

PSS/PDDA自组装膜形成过程中的临界浓度效应

Decher等提出的阴阳聚电解质层层组装膜技术(LbL),方便快捷,结构有序,其纳米级可控,可用于生物传感器、杂多酸多层膜修饰电极及天然多糖类功能膜等领域．LbL膜的厚度直接影响其性能,而膜厚度与紫外吸光度(A)成正比．故A是通常用于评价膜厚度的一种简便方法．紫外吸光度与聚电解质溶液浓度(cp)往往呈递增关系,随着溶液中cp的增大,单位面积上吸附聚电解质的量也增加。     

Photo-cross-linkable polyelectrolyte multilayers for 2-D and 3-D patterning

We report the synthesis of poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linkable weak polyelectrolyte, and its incorporation into polyelectrolyte multilayer (PEM) films. PEM films assembled from PAArVBA and poly(allylamine hydrochloride) (PAH) are found to exhibit similar thickness trends with assembly pH as those previously reported for poly(acrylic acid) (PAA)/PAH multilayers. Swelling properties of the as-built and photo-cross-linked films are studied by in situ ellipsometry. Two-dimensional masking techniques are used to pattern regions of high and low swelling, as confirmed by atomic force microscopy (AFM), and to provide spatial control over the low-pH-induced microporosity transition exhibited by PAH/PAA PEMs. Films containing alternating blocks of PAH/PAArVBA bilayers and PAH/PAA bilayers were assembled, laterally photopatterned, and exposed to low-pH solution to generate nanoporosity leading to patterned Bragg reflectors, thereby demonstrating three-dimensional control over film structure in these weak PEM assemblies.     

由聚电解质自组装多层膜制备微孔薄膜

带有相反电荷的聚电解质通过静电作用交替沉积可以得到自组装多层膜,由于这种技术可操作性强,用途广泛,近十几年来已有了大量的研究．聚电解质多层膜在一定条件下可以形成纳米孔和微米孔．Fu等研究了聚丙烯酸和聚乙烯基吡啶组成的氢键自组装多层膜在碱溶液中溶去其中的聚丙烯酸后,剩下的聚乙烯基吡啶重构形成微孔薄膜．Mendelsohn等发现将聚丙烯酸和聚烯丙基胺自组装而成的多层膜浸入pH=2．4左右的溶液中可制备微孔薄膜．但这些方法并不能使强聚电解质多层膜形成多孔结构。     

Fabrication of free-standing multilayer films by using pH-responsive microgels as sacrificial layers

A facile way to prepare free-standing polyelectrolyte multilayer films of poly(sodium 4-styrenesulfonate)(PSS)/poly(diallyldimethylammonium)(PDDA) was developed by applying a new pH-dependent sacrificial system based on cross-linked poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA) microgels. The tertiary amine groups of PDMAEMA microgels can be protonated in acidic environment, and the protonated microgels were deposited by layer-by-layer (LbL) technique with PSS. PSS/PDDA multilayer films were constructed on the top of the PSS/microgels sacrificial layers. The LbL assembly process was investigated by UV–vis spectroscopy. Further study shows that the free-standing PSS/PDDA multilayer films can be obtained within 3 min by treating the as-prepared films in alkali aqueous solution with a pH of 12.0. The pH-triggered exfoliation of PSS/PDDA multilayer films provides a simple and facile way to prepare LbL assembled free-standing multilayer films.     

Formation and dielectric properties of polyelectrolyte multilayers studied by a silicon-on-insulator based thin film resistor

The formation of polyelectrolyte multilayers (PEMs) is investigated using a silicon-on-insulator based thin film resistor which is sensitive to variations of the surface potential. The buildup of the PEMs at the silicon oxide surface of the device can be observed in real time as defined potential shifts. The influence of polymer charge density is studied using the strong polyanion poly(styrene sulfonate), PSS, combined with the statistical copolymer poly(diallyl-dimethyl-ammoniumchloride-stat-N-methyl-N-vinylacetamide), P(DADMAC-stat-NMVA), at various degrees of charge (DC). The multilayer formation stops after a few deposition steps for a DC below 75%. We show that the threshold of surface charge compensation corresponds to the threshold of multilayer formation. However, no reversion of the preceding surface charge was observed. Screening of polyelectrolyte charges by mobile ions within the polymer film leads to a decrease of the potential shifts with the number of layers deposited. This decrease is much slower for PEMs consisting of P(DADMAC-stat-NMVA) and PSS as compared to PEMs consisting of poly(allylamine-hydrochloride), PAH, and PSS. From this, significant differences in the dielectric constants of the polyelectrolyte films and in the concentration of mobile ions within the films can be derived.     

Modulation of hemocompatibility of polysulfone by polyelectrolyte multilayer films

Polyelectrolyte multilayer (PEM) films have been recently applied to surface modification of biomaterials. Cellular interactions with PEM films consisted of weak polyelectrolytes are greatly affected by the conditions of polyelectrolyte deposition, such as pH of polyelectrolyte solution. Previous studies indicated that the adhesion of several types of mammalian cells to PAH/PAA multilayer films was hindered by low pH and high layer numbers. The objective of this study is to evaluate whether the hemocompatibility of polysulfone can be modulated by deposition of poly(allylamine hydrochloride) (PAH)/poly(acrylic acid) (PAA) multilayer films. PAH/PAA multilayer films with different layer numbers were assembled onto polysulfone at either pH 2.0 or pH 6.5. The number of platelet adhesion and the morphology of adherent platelets were determined to evaluate hemocompatibility of modified substrates. Compared to non-treat polysulfone, the PEM films developed at pH 2.0 decreased platelet adhesion, while those built at pH 6.5 enhanced platelet deposition. Platelet adhesion was found positively correlated to polyclonal antibodies binding to surface-bound fibrinogen. The extent of platelet spreading was increased with layer numbers of PEM films, suggesting that the adherent platelets on thick PEM films were prone to activation. In conclusion, PAH/PAA films with few layers developed at pH 2.0 possessed better hemocompatibility compared to other substrates.     

Assembly of poly(N-isopropylacrylamide)-co-acrylic acid microgel thin films on polyelectrolyte multilayers: Effects of polyelectrolyte layer thickness, surface charge, and microgel solution pH

Temperature- and pH-sensitive poly(N-isopropylacrylamide)?Cco-acrylic acid (pNIPAm-co-AAc) microgels were deposited on glass substrates coated with polyelectrolyte multilayers composed of the polycation poly(allylamine hydrochloride) (PAH) and the polyanion poly(sodium 4-styrenesulfonate) (PSS). The microgel density and structure of the resultant films were investigated as a function of: (1) the number of PAH/PSS layers (layer thickness); (2) the charge on the outer layer of the polyelectrolyte multilayer film; and (3) the pH of microgel deposition solution. The resultant films were studied by differential interference contrast optical microscopy, atomic force microscopy, and scanning electron microscopy. It was found that the coverage of the microgels on the surface was a complex function of the pH of the deposition solution, the charge on the outer layer of the polyelectrolyte thin film and the PAH/PSS layer thickness; although it appears that microgel charge plays the biggest role in determining the resultant surface coverage.     

Surface interactions during polyelectrolyte multilayer build-up. 2. The effect of ionic strength on the structure of preformed multilayers

Interactions between surfaces bearing multilayer films of poly(allylamine hydrochloride) (PAH) and poly(styrenesulfonate sodium salt) (PSS) were investigated across a range of aqueous KBr solutions. Three layer films (PAH/PSS/PAH) were preassembled on mica surfaces, and the resulting interactions were measured with the interferometric surface force apparatus (SFA). Increasing the ionic strength of the medium resulted in a progressive swelling of the multilayer films. Interactions in solutions containing more than 10(-3) M KBr were dominated by a long-ranged steric repulsion originating from compression of polyelectrolyte segments extending into solution. In 10(-1) M KBr, repeated measurements at the same contact position showed a considerable reduction of the range and the strength of the steric force, indicating a flattening of the film during initial approach. Furthermore, this flattening was irreversible on the time scale of the experiments, and measurements performed up to 72 h after the initial compression showed no signs of relaxation. These studies aid in understanding the dominant interactions between polyelectrolyte multilayers, including polyelectrolyte films deposited on colloidal particles, which is important for the preparation of colloidally stable nanoengineered particles.