协效阻燃聚丙烯的阻燃性能

本文研究了以聚磷酸铵(APP)为主阻燃剂,次磷酸铝(AHP)和三聚氰胺氰尿酸盐(MCA)为辅阻燃剂的协效阻燃体系对聚丙烯(PP)阻燃性能的影响。 采用垂直燃烧测试、极限氧指数(LOI)测试、热重分析、锥形量热仪测试、扫描电子显微镜分析等技术手段对所制备的阻燃样品进行了阻燃性能分析。 结果表明:单独添加任一质量分数30%阻燃剂,均不能使PP获得良好的阻燃性能;当阻燃剂总质量分数保持在30%,m(APP)：m(AHP)：m(MCA)=4：1：1时获得理想阻燃效果,此时阻燃PP的LOI为33%,垂直燃烧测试达到V-0级,热释放速率峰值(PHRR)从765.7 kW/m²降为122.7 kW/m²。     

微氧化烧结制备掺杂Y2O3的SiC陶瓷及含镉模拟废水处理

采用了微氧化烧结制备了不同Y₂O₃质量分数（0%、2%、4%、6%）的多孔SiC陶瓷，通过对陶瓷的晶体结构、微观形貌、物理性能和Cd²⁺的去除率测试发现：添加了Y₂O₃的SiC陶瓷出现了较多的第二相Y₂SiO₇、Y₅Si₃C_0.5，随着Y₂O₃的质量分数增加逐渐升高，主相的衍射峰的强度有降低。扫描电子显微镜测试发现，SiC陶瓷的尺寸在2.5 μm，Y₂O₃引入后，SiC陶瓷的晶粒尺寸降低，高温烧结时液相的含量增加，熔体粘度降低，晶粒结合更加紧密，Y₂O₃的引入提高了多孔陶瓷的体积密度，Y₂O₃质量分数为6%SiC的体积密度最大为2.21 g/cm³。热导率随着Y₂O₃质量分数的增加呈现出先升高后降低的趋势。金属Cd²⁺的过滤测试表明：随着Y₂O₃质量分数增加，Cd²⁺的残留质量浓度、膜通量和去除率先降低后升高，当掺杂质量分数为4%时，Cd²⁺残留质量浓度最低为0.042 mg/L，膜通量达到了最大值572 L/（m²·h），去除率最大为99.95%，相比未掺质量分数杂体系的去除率提高了0.14%。随着溶液pH值的逐渐增大，金属Cd²⁺的残留质量浓度逐渐降低、去除率逐渐升高，pH≥9时最终均趋于稳定。综合来看，多孔SiC陶瓷的助烧剂Y₂O₃最佳掺量为4%。     

KMnF3的熔盐法合成及掺铕体系的发光性质

采用简单的熔盐法合成了KMnF₃单相样品及稀土离子铕掺杂的KMnF₃（KMnF₃：Eu）荧光样品. X射线粉末衍射（XRD）表征结果显示,KMnF₃属立方晶系,为AMF₃型钙钛矿结构氟化物. 对样品KMnF₃：Eu的发光性质进行了研究,荧光光谱分析结果表明,Mn²⁺,Eu²⁺与Eu³⁺这3个发光中心共存于KMnF₃：Eu体系中. 讨论了改变掺入Eu离子的摩尔分数对Mn²⁺,Eu²⁺以及Eu³⁺发光强度的影响.     

三（三溴苯氧基）三嗪的合成及阻燃性能

以苯酚和三聚氯氰为原料,合成了一种溴氮型阻燃剂--三（三溴苯氧基）三嗪（3）,收率95.8%,其结构和性能经¹H NMR, ¹³C NMR和TG-DTG表征。采用极限氧指数（LOI）测试研究了3对环氧树脂（EP）的阻燃性能。结果表明：3的T₅为331 ℃, 500 ℃残炭率为8.25%。 3的用量为25%时,3²⁵-EP的LOI为28%,阻燃级别为难燃。     

室温下快速合成超小Fe3+掺杂BiF3纳米粒子

室温下快速合成了Fe³⁺掺杂的BiF₃超小纳米粒子,只需要反应1 min,较小的Fe³⁺离子即可替代BiF₃晶格中较大的Bi³⁺离子.随着Fe³⁺掺杂量的增加,BiF₃：Fe³⁺纳米粒子的粒径不断减小,当Fe³⁺的掺杂量达到0.119时,可以得到尺寸约为6.9 nm的Fe³⁺掺杂BiF₃超小纳米粒子.此外,Fe³⁺离子的掺杂使BiF₃：Fe³⁺-x样品的能带结构发生了显著变化.制备的Fe³⁺掺杂BiF₃超小纳米粒子在光催化剂和荧光材料方面具有潜在的应用价值.     

阻燃剂对镍钴锰三元材料体系电化学性能的影响

测试了不同浓度的电解液阻燃添加剂对镍钴锰三元材料（LiNi_0.4Co_0.2Mn_0.4O₂）作为正极的锂离子电池电化学性能的影响. 实验结果表明,当阻燃剂浓度增加时,电池的放电容量下降,电化学反应电阻和锂离子扩散阻力都有所增加,但加入阻燃添加剂的锂离子电池,当充放电的电流相对比较小的时候,循环性能相比于不含阻燃剂的有所提高,循环稳定性得到了改善. 在0.5C倍率电流下,不含阻燃剂时容量保持率为89%,而当阻燃剂含量增至10%后保持率达到94.21%. 当充放电电流为1C时,未使用阻燃剂时容量保持率约为92.22%,当阻燃剂的浓度为10%时容量保持率为93.01%. 在2C倍率下,不含阻燃剂时容量保持率为87.92%. 阻燃剂浓度为10%时,容量保持率有所提升,达到92.16%. 与基础电解液相比,选用含有10%阻燃剂的电解液可使容量保持率提高5%左右,相比于其他浓度,包含10%阻燃剂的电池循环性能也最为稳定.     

氨基修饰介孔SiO2的合成及对其对Hg2+、 Ni2+和Mn2+的吸附

利用介孔SiO₂微球（MSM）作为基底,对其表面进行氨基修饰,合成了氨基修饰介孔SiO₂微球（MSM/NH₂）,其结构和性能经TEM, XRD和元素分析表征。结果表明：MSM/NH₂ 1.0［3-氨丙基三乙氧基硅烷（APTES）用量为1.0 mL］对Hg²⁺、 Ni²⁺和Mn²⁺的5次循环吸附效率的平均值均超过92.0%。     

反应型阻燃剂三(2-羟乙基)磷酸酯的合成及性能评价

以三氯氧磷和乙二醇为原料，合成了一种反应型无卤阻燃剂三（2-羟乙基）磷酸酯（1），其结构和性能经¹H NMR, ¹³C NMR, ³¹P NMR, IR和TGA表征。利用 THEPP制备了含磷本质阻燃硬质聚氨酯泡沫塑料（2ⁿ, n为1的加量）并研究了其阻燃性能。结果表明：1的初始分解温度为164.8 ℃, 700 ℃时的残炭率约23.8%。以20份1替代聚醚多元醇，2²⁰的极限氧指数由18.6%提高至22.5%，水平燃烧测试达到HB级并能够离火自熄。     

阻燃剂对聚碳酸酯透明性能的影响

以透明聚碳酸酯(PC)为基础树脂,在保持PC优异的力学性能和高透明性能的前提下,分别制备了磺酸盐类阻燃剂、硅油类阻燃剂以及两者复配型阻燃剂改性的3组PC体系,测试了PC的阻燃等级及透明性并通过SEM探讨了阻燃机理.研究表明:单独添加质量分数为0.1％的磺酸盐类阻燃剂可使PC阻燃等级达到V-0级并保持良好的力学性能及透明性;单独添加质量分数为1％的硅油类阻燃剂仍能保持PC良好的力学性能及透明性,但是阻燃等级无法达到V-0级;复配质量分数0.05％～0.1％的磺酸盐类阻燃剂及质量分数为0.5％～1％的硅油类阻燃剂,可使PC阻燃等级达到V-0级,并能保持良好的力学性能及透明性,此外复配之后燃烧形成的碳层阻燃效果更好.     

Bi3+掺杂对YVO4:Yb3+近红外发光的敏化作用

用主温固相法合成了Yb³⁺、Bi³⁺共掺的YVO₄,研究了Bi³⁺的掺入对YVO₄:Yb³⁺发光光谱的影响和近红外发光的敏化作用.X射线衍射图谱研究表明:掺入Yb³⁺、Bi³⁺之后,基质YVO₄的晶格结构没有发生明显变化.Bi³⁺的掺入不仅显著增强了样品中Yb³⁺的特征远红外发光强度,还使YVO₄:Yb³⁺激发光谱的范围红移,当Bi³⁺掺入的摩尔分数从0增加到0.05时,样品的最强激发峰位置从335nm红移至352 nm,激发光谱范围由300-360 nm扩宽至300-430 nm.优化的Bi³⁺掺入量为0.03.初步讨论了VO₄^3-,Bi³⁺Yb³⁺间的能量传递机理.结果表明Bi^3-的共掺使YVO₄:Yb³⁺样品对长波紫外光的响应性能大大改善,作为一种基于量子剪裁的光谱转换材料,可以更好地匹配太阳光的能量谱,有助于提高硅太阳能电池的光电转换效率.     

微纳米钙钛矿型羟基锡酸钙的合成及对环氧树脂的阻燃性能

钙钛矿型羟基锡酸盐是近年来出现的新型高效阻燃消烟剂. 本文采用化学共沉淀法合成了微纳米钙钛矿型羟基锡酸钙[CaSn(OH)₆, CSH], 并利用扫描电子显微镜、 透射电子显微镜、 X射线衍射仪、 红外光谱仪和X射线光电子能谱仪等对其形貌和结构进行表征. 结果表明合成的CaSn(OH)₆为平均粒径500 nm的纯净正六面体, 粒径均一且分散性良好. 将CaSn(OH)₆应用于环氧树脂(EP)复合阻燃体系(CSH/EP), 并分别采用热重分析、 极限氧指数和锥形量热测试表征了其热降解行为和燃烧性能. 采用扫描电子显微镜、 红外光谱、 X射线衍射和拉曼光谱对EP复合材料的阻燃成炭机制进行探索. 结果表明, CaSn(OH)₆能显著提高EP复合材料的高温稳定性、 热释放速率、 热释放量、 烟释放量和极限氧指数数值. 特别是在很低添加量(0.5%, 质量分数)下, 阻燃消烟性能即得到极大提升, 热释放速率、 总放热量和一氧化碳释放量分别降低45.8%, 25.1%和31.3%. 此外, 由于CaSn(OH)₆在EP基体中的良好分散及较强的界面作用, CaSn(OH)₆在提升EP复合材料阻燃消烟性的同时还提升了EP复合材料的力学强度. 本文合成的CaSn(OH)₆可作为一种多功能的高效阻燃、 消烟和增强剂.     

The influence of melamine phosphate modified MoS2 on the thermal and flammability of poly(butylene succinate) composites

This work reported a facile fabrication method to modify molybdenum disulfide (MoS₂) nanosheets with common flame retardant melamine phosphate (MAP) and then were incorporated into poly(butylene succinate) by melt blending method with the purpose of improving the thermal and flame retardancy properties. MAP modified MoS₂ nanosheets dispersed well in poly(butylene succinate) composites with intercalated structure. The incorporation of MAP modified MoS₂ nanosheets led to an increase of thermal degradation temperature and char formation as well as reduction of the peak heat release rate. Copyright © 2016 John Wiley & Sons, Ltd.     

Evaluation of activation energy conformity derived from model-free non-isothermal predictions and Arrhenius isothermal results

Organically modified montmorillonite (OMMT) was used as synergist to enhance the flame-retardant and mechanical properties of poly(butylene succinate)/intumescent flame retardant (PBS/IFR) composites. The flame-retardant, thermal degradation and combustion properties of PBS and its flame-retardant composites were characterized by limiting oxygen index (LOI) test, vertical burning (UL-94) test, thermogravimetric analysis, cone calorimeter and scanning electron microscopy, respectively. The results indicate that PBS/IFR composites exhibit excellent flame retardance when OMMT is at an appropriate content. PBS/IFR composite with 20 wt% IFR and 1.5 wt% OMMT has an LOI of 40.1% and can pass the UL-94 V0 rating. The synergistic effect between OMMT and IFR on the flame-retardant properties of PBS depends on the content of OMMT, and excessive OMMT diminish this synergistic effect. The possible flame-retardant mechanism of OMMT on PBS/IFR composite is proposed. The results of mechanical test also indicate that OMMT can effectively increase the notched impact strength of PBS/IFR composites.     

A flame‐retardant DOPO‐MgAl‐LDH was prepared and applied in poly (methyl methacrylate) resin

A novel inorganic and organic composite flame retardant (9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide [DOPO]–layered double hydroxide [LDH]) was synthesized via grafting DOPO with organic‐modified Mg/Al‐LDH, which was introduced into poly (methyl methacrylate) (PMMA) resin to prepare the flame‐retardant PMMA composites. Thermogravimetric analyzer (TGA) showed that the T_‐50% of DOPO‐LDH/PMMA composites enhanced by about 20°C, and with the 20% flame retardant, the residual char content can be increased by 39.8% in the air atmosphere compared with LDH/PMMA composites. In the UL‐94 and the limiting oxygen index (LOI) tests, it can be found that compared with LDH/PMMA composites, the LOI value of DOPO‐LDH/PMMA composites were raised evidently with the increased flame retardants, and the droplet combustion was greatly improved. These results could be ascribed to the action of DOPO free‐radical, catalytic charring of polymer and the effect of LDH physical barrier. Moreover, the novel DOPO‐LDH not only given PMMA a good flame‐retardant property and thermal stability, but also have higher visible light transmittance, ultraviolet‐shielding effect, and low loss of mechanical properties, which could further facilitate the wide application of inorganic environment‐friendly flame retardants in general resins and engineering resins and broaden the application of polymers.     

原位共沉淀法制备Ni-Mg-Al-LDHs/γ-Al2O3催化前驱体在甲烷二氧化碳重整反应体系中的性能评价

通过原位共沉淀的方法在γ-Al₂O₃表面上合成了Ni-Mg-Al-LDHs (水滑石), 合成的Ni-Mg-Al-LDHs/γ-Al₂O₃作为催化前驱体经过不同的热处理还原方式得到催化剂Cat-1、Cat-2和Cat-3. 用X射线衍射(XRD)、透射电镜(TEM)、N₂吸附-脱附测试(BET)以及热重-差热分析(TG-DTA)对催化剂的形貌结构和抗积碳能力进行了表征测试; 通过甲烷二氧化碳重整反应体系对催化剂的反应活性和稳定性进行了评价. 结果表明催化剂前驱体的预处理方式对催化剂的反应性能具有较大的影响. Ni-Mg-Al-LDHs/γ-Al₂O₃ 直接经过H2/Ar 常压高频冷等离子体炬的分解还原所获得的催化剂Cat-3 表现出了最佳的催化活性和稳定性. TEM表征表明催化活性组分在Cat-3上的分散性更好, 颗粒粒径更小. BET结果证明Cat-3具备较大的比表面积(195.8 m²·g^-1). Ni-Mg-Al 水滑石的结构赋予了催化剂活性组分在载体γ-Al₂O₃上均匀的分散性, 同时常压高频冷等离体炬对催化剂的表面结构以及活性组分的还原具有进一步的优化作用, 两者的协同作用使Ni-Mg-Al-LDHs/γ-Al₂O₃在甲烷二氧化碳反应体系中具备优良的催化活性和抗积碳性能.     

Properties and characteristics of polylactide blends: Synergistic combination of poly(butylene succinate) and flame retardant

A study on the influence of flame‐retardant types, poly(butylene succinate) (PBS) contents, and combination of flame retardant and PBS on the mechanical, thermal, morphological, and flame retardancy properties of polylactide (PLA) and PLA/PBS blends was investigated. Blending of PLA, PBS, and flame retardant was prepared by a twin screw extruder. Tricresyl phosphate (TCP) and montmorillonite (MMT) were used as a flame retardant, whereas PBS acted as a flexible material for enhancing the fire resistance and toughness of PLA, respectively. The results revealed that the introducing of TCP and MMT greatly improved the impact strength of the PLA. The impact toughness of PLA blends with 20 wt% of PBS increased to about 244% that of neat PLA. The addition of flame retardants markedly improved the limiting oxygen index of PLA from 18.0% to 30.1% and 24.3% for the blends containing TCP and MMT. The V‐0 rating in UL‐94 testing was achieved with PLA/TCP blend. Elongation at break, impact toughness, and thermal stability of PLA significantly increased with the increment of PBS concentration. The synergistic effect of flame retardant and PBS afforded the PLA blends with outstanding increase of impact resistance. Furthermore, the flame retardant of TCP in the system not only affected dripping behavior and total flame time of PLA/PBS blends but also improved limiting oxygen index values due to the forming of char layer and inhibiting of burning mechanism.     

Synthesis of a novel polyphosphazene/triazine bi‐group flame retardant in situ doping nano zinc oxide and its application in poly (lactic acid) resin

A novel polyphosphazene/triazine bi‐group flame retardant in situ doping nano ZnO (A4‐d‐ZnO) was synthesized and applied in poly (lactic acid) (PLA). Fourier transform infrared (FTIR), solid state nuclear magnetic resonance (SSNMR), X‐ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscope (TEM), and energy dispersive spectrometer (EDS) were used to confirm the chemical structure of A4‐d‐ZnO. The thermal stability and the flame‐retardant properties of the PLA composites were characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), limiting oxygen index (LOI), vertical burning test (UL‐94), and micro combustion calorimeter (MCC) test. The results of XPS showed that A4‐d‐ZnO has been synthesized, and the doping ratio of ZnO was 7.2% in flame‐retardant A4‐d‐ZnO. TGA results revealed that A4‐d‐ZnO had good char forming ability (40 wt% at 600°C). The results of LOI, vertical burning test, and MCC showed that PLA/5%A4‐d‐ZnO composite acquired a higher LOI value (24%), higher UL94 rating, and lower pk‐HRR (501 kW/m²) comparing with that of pure PLA. It indicated that a small amount of flame‐retardant A4‐d‐ZnO could achieve great flame‐retardant performance in PLA composites. The catalytic chain scission effect of A4‐d‐ZnO could make PLA composites drip with flame and go out during combustion, which was the reason for the good flame‐retardant property. Moreover, after the addition of A4‐d‐ZnO, the impaired mechanical properties of PLA composites are minimal enough.     

Preparation and characterization of microencapsulated LDHs with melamine‐formaldehyde resin and its flame retardant application in epoxy resin

Layered double hydroxides (LDHs) are emerging as a new and green high‐efficient flame retardant. But LDHs aggregate seriously because of their hydrophilicity, which affect deeply the mechanical and flame retardant properties of their composites. For the first time in this paper, microencapsulated LDHs (MCLDHs) with melamine‐formaldehyde (MF) resin were prepared by microencapsulation technology to enhance their compatibility and dispersion within epoxy resin (EP). The mechanical and flame retardant performances of EP/MCLDH composite were studied by comparing with EP/LDH composite. Results showed that the water contact angle of MCLDHs increased from 8.9° to 122.1°, which indicated good compatibility. The particle size of MCLDHs decreased sharply, and more than one‐third were up to submicron scale, which can be conducive to dispersion. Moreover, the tensile strength and elongation at break of EP/MCLDHs with different flame retardant contents were higher than those of EP/LDHs. And the addition of MCLDHs increased the glass transition temperature (Tg) of EP/MCLDHs, which meant a strong interfacial interaction. Besides, compared with EP/LDHs, the limiting oxygen index values of EP/MCLDHs were higher, and its peak of heat release rate and total heat release decreased by 16.3% and 5.5% respectively. EP/MCLDHs achieved from V‐1 to V‐0 rate with the increasing content of MCLDHs from 20% to 30%, while LDHs/EP never passed tests. In the process of heating, H₂O, CO₂, and NH₃ released from MCLDHs formed gaseous phase, and the remaining dense char layers and oxides produced condensed phase, which played an important role in inhibiting combustion.     

An efficient halogen-free flame retardant for glass-fibre-reinforced poly(butylene terephthalate)

Compared with poly(butylene terephthalate) (PBT), glass-fibre-reinforced poly(butylene terephthalate) (GF-PBT) is difficult to flame retard with halogen-free flame retardants. In the present study, the aluminium salt of hypophosphorous acid (AP) was used as a flame retardant for GF-PBT. A series of flame-retardant GF-PBT composites was prepared via melt compounding. The flame retardance and combustion behaviour of the composites were studied by limiting oxygen index (LOI), vertical burning test (UL-94) and cone calorimetric test. Thermal behaviours and thermal decomposition kinetics were investigated by thermogravimetric analysis (TGA) under N₂ atmosphere. The addition of AP to the composites could result in an increased LOI value, a UL-94 V-0 (1.6 mm) classification and a better fire performance in cone calorimetric tests. The char morphology observation after flame-retardant tests, calculation of decomposition kinetics, X-ray photoelectron spectroscopy (XPS) and infra-red spectral analysis of the char residue confirmed the condensed-phase flame-retardant mechanism. Furthermore, the mechanical properties of the flame-retardant composites were not deteriorated, retaining an acceptable level.     

Synergistic effect of ammonium polyphosphate and layered double hydroxide on flame retardant properties of poly(vinyl alcohol)

A novel flame retardant system of poly(vinyl alcohol) (PVA) is prepared via using ammonium polyphosphate (APP) and layered double hydroxide (LDH). The flammability of PVA composites containing APP-based LDH at a 15 wt.% global percentage showed that the flame retardancy of all PVA/APP/LDH samples increase with the increase of LDH concentration in the range of 0.1-1.0 wt.%, and reach a LOI value of up to 33 and UL-94 V-0 rating for most composites. Thermo-gravimetric analysis reveals that PVA/APP/LDH samples show higher initial decomposition temperature in comparison with PVA/APP composite. The morphology and structures of residues generated during LOI test were investigated by scanning electronic microscopy (SEM). Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) were used to analyze the composition of the residue formed after thermo-oxidation to support a fundamental analysis for the mechanism of char formation. The test of mechanical properties demonstrated that LDH can enhance tensile strength, Young's modulus and elongation at break of PVA/APP composites.