输出能量4mJ的1kHz飞秒掺钛蓝宝石激光再生放大研究

针对高能量千赫兹重复频率飞秒激光的应用需求,设计了一套采用线性再生腔结构的高效率飞秒钛宝石激光啁啾脉冲放大系统.通过优化腔型设计,在重复频率为1 kHz、单脉冲能量为20 mJ的527 nm激光抽运下,将展宽后的800 nm啁啾脉冲激光的能量放大到5.8 mJ,对应斜效率达到30.7%.进一步通过色散补偿压缩脉冲宽度,获得了单脉冲能量为4 mJ、脉冲宽度为45.7 fs的输出,稳定性测量表明激光的能量抖动仅为0.18%(均方根值).     

全固态kHz啁啾脉冲飞秒激光放大器

要建造大功率超强激光系统,必须将nJ量级的种子进行放大,以得到mJ量级以及更高能量的激光输出.为达到这个目的,必须使种子能量指数增加,再生腔放大器是实现这一目的的良好途径;同时,为了得到更稳定的激光输出,须采用高重复频率的泵浦源.为此,设计了一种kHz重复频率激光泵浦的再生放大器,使用15 mJ的527 nm的绿光泵浦,得到了约2.3 mJ的800 nm放大激光输出,同时,对其输出激光的光谱特性进行了测量,将带宽为40 nm的种子注入后,得到了光谱带宽约为30 nm激光输出.     

基于大基模体积的10mJ飞秒钛宝石激光再生放大器

文章报导了基于大基模体积的高能量飞秒钛宝石激光再生放大器的设计与实验研究,在重复频率10 Hz、抽运能量60 mJ的激励下,得到了单脉冲能量17.4 mJ的种子脉冲放大结果,压缩后的脉冲宽度为40.6 fs,能量为13.9 mJ.借助于此大基模体积再生腔,仅增加一级多通放大,实现了峰值功率达1.9 TW飞秒激光脉冲输出.结果表明,大模体积再生放大不仅降低了后续放大对抽运能量的要求,也可以单独压缩实现再生腔直接输出10 mJ量级的飞秒激光脉冲,是大能量高峰值功率飞秒激光系统的优质前端.     

A 61-mJ, 1-kHz cryogenic Yb: YAG laser amplifier

We report a diode-pumped rod-type Yb:YAG laser amplifier operating at 1 kHz. Cryogenic cooling method was adopted to make the Yb:YAG crystal work with four-level behavior. A single-frequency fiber laser acts as the seed in an actively Q-switched Yb:YAG oscillator. The resonator delivers 5.75-mJ pulses at 1 kHz with a pulse duration of approximately 40 ns. The pulses were amplified to 61 mJ in a four-pass rod-type Yb:YAG amplifier with optical-to-optical efficiency of 24% in the main amplifier. The M² parameter of the output laser is <1.4.     

低重复率的Ti:Al2O3飞秒激光放大器研究

本文报道了重复频率为10Hz的Ti:Al₂O₃飞秒激光放大器的研究.基于脉冲啁啾放大技术和采用再生/多通放大装置,得到了能量为8mJ的放大光脉冲,在该放大系统中,激光脉冲获M净增益约8×10⁷.     

Picosecond laser system with 30-W average power via cavity dumping and amplifying

We present a picosecond laser system with high energy by technologies of cavity dumping and amplifying. Firstly, pulses with 10 ps and ～520 nJ were obtained by cavity-dumped mode-locked laser at 10 kHz repetition rate. Secondly those pulses were seeded into a side-pumped regenerative amplifier (RA). Then pulses output from the regenerative amplifier were amplified by two four-pass post amplifiers. From the laser system pulses with an average power of 30 W corresponding to 3 mJ pulse energy were achieved with the pulse-width of 25.4 ps at repetition rate of 10 kHz.     

Sub-picosecond pulses at 100 W average power from a Yb:YLF chirped-pulse amplification system

We present a high-repetition-frequency, diode-pumped, and chirped-pulse amplification system operating at 106 W average output power with excellent beam quality (M(2)=1.3), based on cryogenically cooled Yb:YLF. 1 nJ seed pulses, derived from a mode-locked Ti:sapphire laser, are first amplified to 1 mJ pulse energy at 10 kHz repetition frequency in a regenerative amplifier. The second-stage, multipass amplifier increases the pulse energy to 10.6 mJ, resulting in a spectral width of 2.2 nm. The pulses are compressed to 865 fs in duration, which is 1.26 times the transform limit.     

Carrier envelope phase stabilization of a Yb:KGW laser amplifier

In this paper we report on the active stabilization of the carrier envelope phase (CEP) of a Yb:KGW chirped pulse amplifier laser system seeded by a Yb-doped solid-state Kerr-lens mode-locked oscillator. The regenerative amplifier delivers 180 fs CEP stable pulses of 30 μJ-1 mJ energy at a repetition rate tunable from 1 to 200 kHz. The bandwidth of the feedback loop was extended by a factor of 5 using a specially designed high-pass filter, which resulted in a dramatic decrease of CEP jitter below 0.45 rad after the amplifier.     

Tunable phase-stabilized infrared parametric laser source

This paper reports that the tunable self-phase-stabilized infrared laser pulses have been generated from a two-stage optical parametric amplifier. With an 800 nm pump source, the output idler pulses are tunable from 1.3 μm to 2.3 μm, and the maximum output energy of the idler pulses is higher than 1 mJ at 1.6 μm by using 6 mJ pump laser. A carrier-envelope phase fluctuation of ～ 0.15 rad (rms) for the idler pulses is measured for longer than one hour by using a home build f-to-2f interferometer.     

采用环形再生腔结构的飞秒激光啁啾脉冲放大研究

采用环形再生腔结构的啁啾脉冲放大技术方案, 在重复频率100 Hz,单脉冲能量33.1 mJ的532 nm激光抽运下, 从钛宝石激光中获得了单脉冲能量9.84 mJ的放大输出, 对应的斜效率达33.1%.在重复频率10 Hz的情况下, 同样获得了单脉冲能量为9.64 mJ, 对应斜效率达36.8%的高效率放大结果. 通过色散补偿压缩该啁啾激光脉冲后的单脉冲能量为6.36 mJ, 脉冲宽度为59.7 fs. 测量结果表明典型的能量不稳定度为1.85%. 关键词： 啁啾脉冲放大 再生放大 飞秒激光 环形腔     

High-average-power kilohertz-repetition-rate sub-100-fs Ti:sapphire amplifier system

We report on a femtosecond Ti:sapphire laser amplifier system that generates pulse energies >5 mJ at a 1-kHz repetition rate. The system consists of regenerative and multipass amplifiers and uses the technique of chirped-pulse amplification. When the system was seeded with 70-fs pulses at 800 nm from a self-mode-locked Ti:sapphire oscillator, amplified pulses of 94-fs duration at a repetition rate of 1 kHz and an average output power of 5.4 W were produced. The amplified pulse-repetition rate is variable from 250 Hz to 3 kHz. Pulse energies of >7.5 mJ were obtained at 500 and 250 Hz.     

Ti:sapphire Regenerative Amplifier at 1.056 μm

The design and performance of a Ti:sapphire regenerative amplifier operating at 1. 056 μm are described. A laser pulse with an initial pulsewidth of 100 fs is amplified to ≥1.5 mJ in the amplifier after firstly stretched to 850 ps. The amplified pulse can be re-compressed to ～300 fs with energy of ～1 mJ. Loss of the spectrum happens in the regenerative cavity since bandwidth of the coat of optics in the cavity is not enough adequate.     

Intense few-cycle laser pulses from self-compression in a self-guiding filament

Sub-10-fs-pulses are generated by self-compression in a noble gas filament. Using input pulses from a Ti:sapphire amplifier system with an energy of about 1.5 mJ at a repetition rate of 3 kHz and a pulse duration of 30 fs self-compressed sub-10-fs pulses with energies of about 0.3 mJ have been generated. These pulses are characterized with spectral phase interferometry for direct electrical-field reconstruction (SPIDER). Depending on the laser parameters, we observe a significant change in the chirp of the white-light. The spectral distribution of the outcoming beam profile is measured to distinguish the white-light core from the surrounding halo.     

高能量环形长腔再生放大啁啾脉冲激光的研究

介绍了一种新型的高能量环形长腔再生放大器, 通过对谐振腔的模式分布进行计算, 建立了腔长为12 m的环形腔再生放大器, 在150 mJ的抽运能量下, 得到了单脉冲能量为20 mJ的放大激光输出, 对应的转化效率为13.3%, 其输出激光的能量远远超过了常规的再生放大器输出激光的单脉冲量. 放大激光的输出光谱为30 nm, 可以支持<40 fs的傅里叶转换极限脉宽. 关键词： 环形腔 再生放大 高能量     

Highly Efficient and Stable Ring Regenerative Amplifier for Chirped-Pulse Amplification at Repetition Rate 1 kHz

A highly efficient and stable ring-cavity regenerative amplifier for chirped-pulse amplification at a 1 kHz repetition rate, with slope efficiency up to 40% and output pulse-to-pulse energy-jitter less than 1.25%, is demonstrated. The pulse energy as high as 2.4mJ is obtained.     

无展宽器的高重复率钛宝石啁啾飞秒脉冲再生放大器的研究

通过优化放大腔结构参数和采用高光束质量的泵浦激光,依靠放大器腔内各个元件的色散展宽种子脉冲, 用钛宝石作为增益介质, 在低泵浦能量下, 实现了高光束质量,高稳定的中等能量的高重复率飞秒脉冲再生放大. 将钛宝石晶体离焦放置,有效的避免了光学损伤. 在1.1 mJ的绿光泵浦下, 获得了2 ps, 120 μJ, 重复频率为1 KHz, 光谱带宽7.8 nm的放大脉冲, 用石英棱镜对压缩可得到130 fs的激光脉冲.     

High-power parametric amplification of 11.8-fs laser pulses with carrier-envelope phase control

Phase-stable parametric chirped-pulse amplification of ultrashort pulses from a carrier-envelope phase-stabilized mode-locked Ti:sapphire oscillator (11.0 fs) to 0.25 mJ/pulse at 1 kHz is demonstrated. Compression with a grating compressor and a LCD shaper yields near-Fourier-limited 11.8-fs pulses with an energy of 0.12 mJ. The amplifier is pumped by 532-nm pulses from a synchronized mode-locked laser, Nd:YAG amplifier system. This approach is shown to be promising for the next generation of ultrafast amplifiers aimed at producing terawatt-level phase-controlled few-cycle laser pulses.     

300 kHz femtosecond Yb:KGW regenerative amplifier using an acousto–optic Q-switch

We report a diode-pumped high-repetition-rate chirped-pulse Yb:KGW regenerative amplifier delivering tens of microjoules pulse energy at repetition rates of up to 300 kHz. High repetition rates are obtained by using an acousto-optic modulator as switching element in the regenerative amplifier cavity. The output pulses were compressed down to 600 fs pulse duration. Even shorter pulses in the 100 fs range are obtained using an amplifier configuration without chirped pulse amplification. PACS 42.55.Xi; 42.60.Da; 42.65 Re     

飞秒激光脉冲的高效率放大研究

介绍了采用多通放大的飞秒脉冲掺钛蓝宝石激光放大系统,分析讨论了提高放大效率及缩短脉冲宽度的技术方法。在仅用能量２９０ｍＪ的倍频Ｎｄ：ＹＡＧ激光泵浦下,得到了输出峰值功率大于１．４ＴＷ、脉宽２５ｆｓ、重复频率１０Ｈｚ的超短超强激光脉冲。     

1.5 mJ, 6.4 fs parametric chirped-pulse amplification system at 1 kHz

We demonstrate an optical parametric chirped-pulse amplification (OPCPA) system with the pulse energy of 1.5 mJ at a 1 kHz repetition rate. The newly developed 100 ps Ti:sapphire pump laser system, which was optically synchronized with OPCPA seed pulses, delivered 10 mJ, 400 nm pump pulses. After three-stage parametric amplification, recompression of the amplifier output from 45 ps to 6.4 fs was performed. The pulse width of 6.4 fs is, to our knowledge, the shortest ever obtained by OPCPA, and the average power of 1.5 W (1.5 mJ, 1 kHz) is believed to be the highest among few-cycle OPCPA systems.