Solid-phase microextraction coupled with capillary electrophoresis to determine ephedrine derivatives in water and urine using a sol-gel derived butyl methacrylate/silicone fiber

A sensitive method for determination of ephedrine derivatives using headspace solid-phase microextraction (SPME) with a novel fiber followed by capillary electrophoresis has been developed. The co-poly(butyl methacrylate/hydroxy-terminated silicone oil) (BMA/OH-TSO) was used as stationary phases with the aid of γ-methacryloxypropyltrimethoxysilane (KH-570) as bridge in SPME using sol-gel-coating method and cross-linking technology. It has high extraction efficiency for ephedrine derivatives in comparison with commercial poly(dimethylsiloxane) and poly(acrylate)-coated fiber. The coating exhibits good thermal and solvent stability as well as long lifetime. A simple and flexible device for desorption of analytes after headspace SPME was constructed. The effect of various experimental parameters for SPME (temperature, time, pH, ionic strength, desorption solvent, etc.) were discussed. Field amplified sample injection (FASI) was applied for on-line sample concentration and a sensitivity enhancement of two orders of magnitude was achieved. Linear ranges were found to be 20-5000 ng/ml. The detection limits for (1R,2S)-ephedrine, (1R,2R)-pseudoephedrine and (1S,2S)-pseudoephedrine were 3, 5 and 5 ng/ml, respectively. Relative standard deviation (n = 6) was found to be 4.96-7.57%. The method was successfully applied to the analysis of ephedrine derivatives in human urine.     

High operationally stable sol-gel diglycidyloxycalix[4]arene fiber for solid-phase microextraction of propranolol in human urine

A simple, sensitive, and accurate method for the determination of propranolol in human urine has been developed based on solid-phase microextraction (SPME) followed by GC-flame ionization detection (FID). The sol-gel 5,11,17,23-tetra-tert-butyl-25,27-dihydroxy-26,28-diglycidyloxycalix[4]arene/hydroxy-terminated silicone oil (diglycidyloxy-C[4]/OH-TSO) fiber was prepared to accommodate to the harsh extraction conditions. It possesses excellent alkali-proof ability and retains its extraction characteristics intact even after treatment with highly alkaline (4 mol/L) NaOH solution. Direct chemical bonding of the coating to the fiber surface provides it with excellent solvent resistance and the introduction of calixarene enhances its thermal stability. The newly developed sol-gel calixarene coating was effectively used for the extraction of propranolol in human urine. No interference with the determination of propranolol was observed from the urine components. Standard curves were linear in the range 50-5000 microg/L for headspace-SPME (HS-SPME) and 25-25000 microg/L for direct-SPME (Dir-SPME) with correlation coefficients better than 0.9999. The detection limit was 0.275 microg/L for HS-SPME and 0.193 microg/L for Dir-SPME. The method was validated using standard addition methodology and recovery values were between 91.4 and 117% for both the sampling modes with the RSDs less than 6% at different concentration levels in the linear ranges. The results obtained by both the sampling modes were feasible, and no significant differences between them regarding accuracy, precision, and detection limits were seen.     

Preparation and characteristics of sol-gel-coated calix[4]arene fiber for solid-phase microextraction

5,11,17,23-Tetra-tert-butyl-25,27-diethoxy-26,28-dihydroxycalix[4]arene/hydroxy-terminated silicone oil coated fiber was first prepared and applied for solid-phase microextraction (SPME) with sol-gel technology. The possible sol-gel mechanism was discussed and confirmed by IR spectra. It showed wonderful selectivity and sensitivity to polar (aromatic amines), nonpolar (benzene derivatives, polycyclic aromatic hydrocarbons) and high boiling point compounds (phthalates) and the extraction equilibria were reached quite fast. The coating has high thermal stability (380 degrees C) and solvent stability (organic and inorganic), thus its lifetime is longer than conventional fibers. In addition, it has surprising fiber-to-fiber and batch-to-batch reproducibility. The detection limits were quite low and the linear ranges were pretty broad for all analytes.     

基于杯［6］芳烃萃取头的固相微萃取-气相色谱法测定啤酒中痕量的酞酸酯类化合物

选用自制杯［6］芳烃溶胶-凝胶固相微萃取(SPME)萃取头,建立了顶空SPME与气相色谱联用检测啤酒中8种酞酸酯(PAEs)的方法。采用L25(56)正交设计对萃取条件进行了优化,所得方法检出限为0.003～3.429 μg/L,相对标准偏差不超过13.5%,加标回收率为86.3%～109.3%。采用标准加入法对3种瓶装啤酒中PAEs进行了检测,结果表明邻苯二甲酸二(2-乙基己)酯(DEHP)是啤酒中最主要的酞酸酯类污染物,含量最高达5.24 μg/L。迁移试验表明,瓶装啤酒所用塑料垫圈中高含量的DEHP可能成为酒体中PAEs的一种来源,且延长贮存时间、提高贮存温度和振荡都能加快垫圈中DEHP的迁移。     

Study of a novel cationic calix[4]arene used a selectivity modifier in capillary electrophoresis with electrochemical detection

The use of a novel cationic calixarene, p-(quaternary ammonium) calix[4]arene, as selectivity modifier in capillary electrophoresis coupled with electrochemical detection was reported. The calixarene displayed good selectivity for the positional isomers of benzenediol and aminophenol and their successful separation was obtained under optimum conditions. The interaction mechanism between p-(quaternary ammonium) calix[4]arene and the solutes is discussed using the molecular modeling method. The detection limits by electrochemical detection for the most solutes studied here were below picogram level, which was 2 orders of magnitude lower than those reported in the literature using UV detection. The results showed that electrochemical detection is especially suitable for an electrophoresis system where calixarenes are used as modifier.     

Determination of organochlorine pesticides and their metabolites in radish after headspace solid-phase microextraction using calix[4]arene fiber

A novel laboratory-made sol-gel calix[4]arene/hydroxy-terminated silicone oil coated fiber has been applied for headspace solid-phase microextraction (HS-SPME) combined with gas chromatography (GC) with electron capture detection (ECD) to determine 12 organochlorine pesticides (OCPs) and their metabolites in radish sample. The analytes in the study consisted of α-, β-, γ- and δ-hexachlorocyclohexane (BHC), 1,1,1-trichloro-2-(2-chlorophenyl)-2-(4-chlorophenyl)ethane (o,p′-DDT), 1,1,1-trichloro-2,2-bis(4-chlorophenyl)ethane (p,p′-DDT), 2,4-dichlorobenzophenone (o,p′-DBP), 4,4-dichlorobenzophenone (p,p′-DBP), 1,1-dichloro-2,2-bis(4-chlorophenyl)ethylene (p,p′-DDE), bis(4-chlorophenyl)methane (p,p′-DDM), 1,1-dichloro-2,2-bis(4-chlorophenyl)ethane (p,p′-DDD) and endrin. The following parameters were adjusted to optimize HS-SPME in order to obtain the maximum sensitivity: extraction temperature, extraction time, the addition of salt, desorption temperature and time. Especially, the effect of the complex radish matrix on quantitative extraction of pesticides was discussed in detail. Detection limits of the developed method for radish matrices were below 174 ng/kg for all pesticides. Relative standard deviations for quintuplicate analyses of radish samples fortified each analytes were not higher than 13.1%. The results demonstrate the suitability of the HS-SPME/GC-ECD approach for the analysis of multi-residue OCPs and metabolites in radish.     

A novel sol-gel calix[4]arene-modified capillary column for open-tubular capillary electrochromatography

A novel open-tubular CEC (OT-CEC) column was prepared by immobilized 5,11,17,23-tetra-tert-butyl-25,27-diethoxy-26,28-dihydroxy-calix[4]arene (Calix[4]) on fused-silica capillary column with sol-gel technology. Calix[4] was initially reacted with gamma-glycidoxypropyltrimethoxysilane (KH-560) to form a new sol-gel precursor (calix[4]-KH-560), and then mixed with another precursor, namely tetraethoxysilane (TEOS). After hydrolysis and condensation, a sol-gel matrix was obtained, in which calix[4] was incorporated. Successful calix[4]-modified sol-gel coating was suggested by infrared (IR) spectra and greatly decreased EOF. In comparison with OT columns prepared by the sol-gel method with TEOS and KH-560 only, the calix[4]-modified sol-gel column showed greatly improved separation of isomeric toluidines, nitrophenols, picolines and neurotransmitters with structural similarity. Migration time and theoretical plate number reproducibility were satisfactory with RSDs less than 1 and 6% each for within column runs and not more than 3 and 7% each for column-to-column measurements, using toluidine and nitrophenol isomers as test solutes on this column. High separation efficiencies (96,000-300,000 plates/m) for basic toluidine isomers were obtained. This column was also successfully employed to combine extraction procedure for the determination of dopamine (DA) and norepinephrine (NE) in Portulaca oleracea L. The recoveries of DA and NE were 93.3 and 94.2%, respectively.     

Solid-phase microextraction using a diglycidyloxycalix[4]arene coated fiber combined with gas chromatography: very simple, rapid and sensitive method for the determination of chlorobenzenes in water

A fiber material for solid-phase microextraction (SPME) was obtained by blending 5,11,17,23-tetra-tert-butyl-25,27-dihydroxy-26,28-diglycidyloxycalix[4]arene with hydroxy-terminated silicone oil by sol-gel technology. It was used for headspace SPME combined with gas chromatography using electron capture detection to determine seven chlorobenzenes in water matrix. Optimum extraction conditions were 15 min at 20 °C with a solution containing 300 g L^?1 sodium chloride. The fiber exhibits far higher extraction efficiency than the commercially available poly(dimethylsiloxane) (PDMS) and PDMS-divinylbenzene fibers. The detection limits range from 0.32 to 2.25 ng L^?1, and the relative standard deviations are <5%. The calibration curves display a high level of linearity, with correlation coefficients ranging between 0.9996 and 1. The method was applied to analyze a lake water sample that was found to be polluted with 1,2,3,4-tetrachlorobenzene and hexachlorobenzene. It was compared to the United States Environmental Protection Agency method and other recently introduced methods. The results demonstrate that the technique is rapid, simple, and sensitive, and thus represents an attractive alternative for ultra-trace analysis of chlorobenzenes in water samples.     

Colorimetric recognition of anions using preorganized tetra-amidourea derived calix[4]arene sensors

The synthesis and the spectroscopic studies of the amidourea based calix[4]arene sensors 1 and 2 are described. The 4-nitrophenyl based sensor 1 was synthesized in two steps from the corresponding calix [4]arene tetraethyl ester and shown to give rise to color changes in the UV-vis spectra in DMSO upon recognition of pyrophosphate and fluoride. Fitting the changes in the absorption spectra using nonlinear regression analysis indicated strong binding of several anions by 1 such as acetate and hydrogen phosphate in 1:1 (Host:Guest) stoichiometry, and at higher concentration in 1:2 stoichiometry. The preorganized calix-cavity was, however, not found to host chlorine while binding of bromide was determined. At high concentrations of these anions, significant colorimetric changes were also observed that were clearly visible to the naked eye for both pyrophosphate and fluoride. The phenyl analogue 2 was made to enable analysis of the anion recognition using 1H NMR titrations and showed that ions such as phosphate were bound in 1:1 stoichiometry, whereas the "urea" protons were shown to be significantly affected upon coordination to the anion.     

Determination of phthalate acid esters plasticizers in plastic by ultrasonic solvent extraction combined with solid-phase microextraction using calix[4]arene fiber

Ultrasonic solvent extraction combined with solid-phase microextraction (SPME) with calix[4]arene/hydroxy-terminated silicone (C[4]/OH-TSO) oil coated fiber was used to extract phthalate acid esters (PAEs) plasticizers in plastic, such as blood bags, transfusion tubing, food packaging bag, and mineral water bottle for analysis by gas chromatography (GC). Both extraction parameters (i.e. extraction time, extraction temperature, ionic strength) and conditions of the thermal desorption in a GC injector were optimized by analysis of eight phthalates. The fiber shows wonderful sensitivity and selectivity to the tested compounds. Owing to its high thermal stability (380 °C), the carryover effect that often encountered when using conventional fibers can be reduced by appropriately enhancing the injector temperature. The method showed linear response over two to four orders of magnitude with correlation coefficients (r) better than 0.996, and limits of detection (LOD) ranged between 0.006 and 0.084 μg l⁻¹. The relative standard deviation values obtained were ≤10%. bis-2-Ethylhexyl phthalate (DEHP) was the sole analyte detected in these plastics and recoveries were in the ranges 95.5-101.4% in all the samples.     

Open-tubular capillary electrochromatography using capillary columns chemically bonded with the new host molecules calix[6]crown,calix[6]arene

Two host molecules, p-tert-butylcalix[6]-1,4-crown-4 and p-tert-butylcalix[6]arene were prepared and attached onto the inner surfaces of capillaries for open-tubular electrochromatography with the aid of gamma-glycidoxypropyl-trimethoxysilane (KH-560) as bridging agent. The successful bonding was confirmed by infrared (IR) results and greatly decreased electroosmotic flow (EOF). Parameters affecting separation, such as buffer pH and organic modifier were studied. The two novel stationary phases were evaluated by the separation of isomeric toluidines, a mixture of pyridine and isomeric picolines, and isomeric dihydroxybenzenes; comparisons between capillaries coated with the two stationary phases and bare capillary were investigated. The special selectivity of these two novel stationary phases showed a certain extent of supramolecular interactions between stationary phases and solutes.     

Fluoride sensing with a PCT-based calix[4]arene

Novel calix[4]arene-based anion sensor 1 with two coumarin units attached via amido functions acting also as binding sites is presented. Complexation of F⁻ by PCT-based 1 causes selectively red-shift in UV-vis absorption and in fluorescence emission due to H-bonding followed by deprotonation of NH-amide groups.     

一种新型杯[4]芳烃的合成

本文通过对特丁基杯[4]芳烃的酚羟基烷基化和苯环特丁基位上的IPSO-硝化制备了一系列对硝基杯[4]芳烃烷基醚,烷基分别是n-C~4H~9(3a)、n-C~8H~1~7(3b)、n-C~1~2H~2~5(3c)和n-C~1~6H~3~3(3d)。^1HNMR表明所有新的杯[4]芳烃都具有锥形(cone)构象。     

Solid-phase synthesis of linear and cyclic peptides containing a calix[4]arene amino acid

Solid-phase synthesis is used to obtain new linear and cyclic N,C-linked peptidocalixarenes. The synthetic strategy allows, for the first time, the condensation of a calix[4]arene amino acid during the stepwise elongation sequence of the peptide. An important role is played by the lower rim functionalization of the calixarene since it modulates the flexibility of the calixarene scaffold and the conformational properties of the resulting non-natural peptide.     

Supramolecular interaction between water-soluble calix[4]arene and ATP--the catalysis of calix[4]arene for hydrolysis of ATP

The catalysis effect of water-soluble calix[4]arene C[4] (calix[4]arene-5,11,17,23-tetrasulfonate) on hydrolysis of ATP in aqueous solution was studied by HPLC. Using laser photolysis and pulse radiolysis, the supramolecular interaction between water-soluble calix[4]arene and ATP was investigated.     

Electrochemical oxidation of a tetraester calix[4]arene

The electrochemical oxidation of tetraethyl ester p-tert-butyl calix[4]arene 1 was observed in acetonitrile solution at a platinum electrode, using either cyclic or square wave voltammetry. The oxidation occurred in a number of processes, with the lowest, process I at a peak potential of 1.10 V vs. Ferrocene, being the best defined response. This was attributed to the one-electron oxidation of the aryl ether functionality present in the calixarene and so should provide a route to the electrochemical detection of calixarenes in non-aqueous mixtures. The oxidation behaviour was dependent on the presence of alkali metal cations in solution. Shifts in the oxidation potentials observed were in good agreement with the order of selectivity for the alkali metal cations.     

Binucleating behaviour of a proximally-diphosphinated calix[4]arene

The long diphosphine 5,11-diphenylphosphanyl-25,26-dipropyloxy-27,28-bis(2-propenyloxy) calix[4]arene (cone) (5), in which the two phosphorus atoms are separated by a semi-rigid linking unit, was prepared in four steps starting from calix[4]arene. Reaction of 5 with AuCl(SEt(2)) or [RuCl(2)(p-cymene)](2) led to calixarenes bearing two metallated pendant arms, [5·(AuCl)(2)] and [5·{RuCl(2)(p-cymene)}(2)], respectively. In the presence of AgBF(4) or [Ni(C(5)H(5))(1,5-cyclooctadiene)]BF(4), diphosphine 5 displayed a marked tendency to form oligomeric material, but under high dilution conditions dimeric species were obtained selectively. The inability of 5 to form chelate complexes was further illustrated by its reaction with [PdCl(2)(1,5-cyclooctadiene)(2)], which led quantitatively to a rare complex in which a diphosphine spans across the dinuclear [PdCl(μ-Cl)(2)PdCl] unit.     

Preferential axial protonation in a zwitterionic calix[4]arene

[structure: see text] Calixarene 3, substituted at two methylene bridges by dimethylamino groups, exists in the crystal and in polar solvents as a zwitterion, with the axial dimethylamino group protonated.     

5-碘[杯(4)芳烃偶氮]氨基喹啉光度法测钯

合成了新试剂5 碘[杯(4)芳烃偶氮]氨基喹啉(ICAQ),并研究了该试剂与钯显色反应条件。结果表明,在pH10.2～11.0的Na2CO3 NaHCO3缓冲介质中,在TritonX 100存在下,试剂与钯发生显色反应,生成1∶1稳定络合物。建立了测定钯的光度法新体系,λmax=625nm,ε=1.42×105L·mol-1·cm-1,钯质量浓度在0～0 80μg/mL内符合比尔定律。方法用于钯催化剂中钯的测定,结果与原子吸收法相符,平行6次测定的RSD在2.5%～3.0%。