Determination of Caffeine Using a Simple Graphite Pencil Electrode with Square-Wave Anodic Stripping Voltammetry

A simple commercial graphite pencil electrode (GPE) was utilized for monitoring caffeine using the square-wave anodic stripping voltammetry (SWASV) method. This method was applied to determine the caffeine levels in several tea samples, which yielded a relative error of 1% in the concentrations. Caffeine was deposited at 0.0V (vs. Ag/AgCl), then reduced at +1.40V to strip it on the GPE. Optimal experimental conditions for the analysis were found to be as follows: pH value of 9 for the medium; deposition potential of 0.0V; deposition time of 120s; SW frequency of 25Hz; SW amplitude of 45mV, and step potential of 6mV. Given these optimum conditions, a linear range was observed within the concentration of 0500mgL^–1. At caffeine concentrations of 50.0, 250.0, and 500.0mgL^–1, the relative standard deviations in measured concentrations (n=12) were 0.19, 0.09, and 0.11%, respectively. The detection limit was found to be 9.2mgL^–1, which is comparable with the result obtained using a carbon paste electrode, equivalent to 8.2mgL^–1.     

Use of 2,4-dinitrophenylhydrazone of glyoxylic acid for the determination of glyoxylic acid by the chromatographic-spectrophotometric method and by differential pulse polarography

Two different methods (one based on chromatography and spectrophotometry and the other on polarography) have been developed for the determination of glyoxylic acid in the form of a derivative with 2,4-dinitrophenylhydrazine (DNPHGA). The TLC method allows the separation of two DNPHGA isomers (trans and cis). Spectrophotometric measurements of the eluents of the separated compounds (=360 nm) allow the determination of GA within the range from 4 to 30 g. Using differential pulse polarography, the conditions of DNPHGA formation were examined. The reduction peak of this derivative (E_P=–0.430 V), observed by dpp, was used to develop a polarographic determination of GA within the concentration range from 110^-4 to 710^–4 mol/l.     

Electrochemical Determination of Cinnamtannin B1 with a Pyrolytic Graphite Electrode

Cinnamtannin B1 (trimeric proanthocyanidin), which is identified and isolated from the effective fraction of the root of Lindera aggregata (Sims) Kosterm, is one kind of condensed tannin used as an effective antipyrotic and antitumor agent. Its electrochemical response can be obtained at a pyrolytic graphite electrode. Consequently, an easily performed and sensitive method for the determination of cinnamtannin B1 is developed. The detection limit is estimated to be 1.0×10^–7M with the linear determination range of 2.0×10^–7M to 1.8×10^–6M. Five replicate analyses of 1.0×10^–6M cinnamtannin B1 yields an RSD value of 2.1%. Since the working electrode does not need to be modified with any other species, it is very stable, repeatable and easily treated, and this method therefore potentially useful in real sample analysis.     

Determination of Trace Iron in KH2PO4 Crystal by Derivative Adsorption Chronopotentiometry

A sensitive derivative adsorption chronopotentiometric method was developed to determine trace amounts of Fe³⁺. The influence of preconcentration time, pH of solution and constant reducing current of the peak height is discussed. The detection limit and the linear range are 5.0×10^–10 and 2.0×10^–93.0×10^–6molL^–1, respectively. The method was used to determine trace Fe³⁺ in KH₂PO₄ crystals (KDP).     

Mixed ligand complexes involving aminoacid dithiocarbamates,substituted phosphines and nickel(II)

Mixed ligand complexes involving four aminoacid dithiocarbamates (RRdtc=glydtc^– (R=H; R=H), methdtc^– (R=H; R=C₃H₇S), sardtc^– (R=Me; R=H), trydtc^– (R=H; R=C₉H₈N), substituted phosphines [PPh₃, Ph₂PCH₂CH₂PPh₂(dppe)] and nickel(II) are reported. All are diamagnetic. Thermal analyses of the complexes are in keeping with the proposed formulae. Thermal decomposition of the dithiocarbamate moiety proceeds through the formation of Ni(SCN)₂. PPh₃ and dppe are lost in the initial decomposition stages.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Syntheses and properties of mixed dinuclear copper(II) complexes with heterocyclic dithiocarbamates and a cyclic octadentate tertiary amine

Five new Cu^II complexes of general formula [Cu₂(Rdtc)tpmc](ClO₄)₃, (1)–(5), where tpmc and Rdtc ^– refer to N,N,N,N-tetrakis(2-pyridylmethyl)-1,4,8,11-teraazacyclotetradecane and piperidine- (Pipdtc), 4-morpholine- (Morphdtc), 4-thiomorpholine- (Timdtc), piperazine- (Pzdtc) or N-methylpiperazine- (N-Mepzdtc) dithiocarbamates, respectively, have been prepared. Elemental analyses, conductometric and magnetic measurements, u.v./vis, i.r., e.p.r. and mass spectroscopy have been employed to characterize them. The complexes adopt an exo coordination of Cu^II ions and tpmc. The dithiocarbamate ion joins both the sulphur and the copper atoms acting as a bridging ligand The presence of different heteroatoms in the piperidine ring influences the (C=N) and (C=S) vibrations which decrease in the order of the complexes: Pipdtc>N-Mepipdtc>Pzdtc>Morphdtc>Timdtc ligands. Attention has been paid to the detailed mechanism of the mass spectral fragmentation of the complexes. The g _eff factors of the complexes have been also estimated by e.p.r. spectra. Finally, the complexes obtained demonstrate microbiologycal activity against some bacteria.     

Investigation of Medium Power Radiofrequency Capacitively Coupled Plasmas and Their Application to Atomic Emission Spectrometry for the Determination of Aluminium in Water Samples

A medium power radiofrequency capacitively coupled plasma (275W, 27.12MHz) with low argon consumption (0.5Lmin^–1) was investigated to be used for the determination of aluminium in water samples pneumatically nebulised by atomic emission spectrometry. The plasma torch was operated in two geometric configurations, coaxial and coaxial-annular with single (SRTr.f.CCP) or double ring electrodes (DRTr.f.CCP), respectively. The optimum experimental parameters (observation height, Ar flow rate, distance between ring electrodes, matrix interference of Na⁺ and Ca²⁺ and anion nature) for Al 396.152nm emission were established. Under optimum operating conditions of the DRTr.f.CCP torch (6cm distance between annular electrodes), a detection limit of 70ngmL^–1 aluminium was found. Both operating parameters and several figures of merit of the investigated plasmas were compared to those of microwave plasmas and inductively coupled plasma used in atomic emission spectrometry. The method was used to control the quality of drinking and industrial water. Samples were mineralised with 2mL of 1+1 HNO₃ and 10mL of 1+1 HCl. In the range of 0.15–3.5mgL^–1 Al³⁺ the relative standard deviation varied between 3.7 and 8.6% (n=3). For two certified drinking water samples containing 0.206 and 0.218mgL^–1 Al³⁺ the recovery (n=5) was 97.6±6.8% and 98.6±7.3%, respectively.     

Nickel Ion-Selective PVC Membrane Electrode Based on a New t-Octyl-Calix[6]arene Derivative

This study presents a PVC membrane based on 5,11,17,23,29,35-Hexakis-t-octyl-37,38,39,40,41,42-hexakis(N-phenylthiocarbamoylmethoxy)calix[6]arene which is used as an electroactive substance. The electrode reveals a Nernstian response for Ni²⁺ over a wide pH range with a slope of linear portion (5×10^–6–1×10^–2M, R=0.988) of 29.75±0.2mV·decade^–1 at 25°C. The electrodes sensitivity is enhanced upon the introduction of sodium tetraphenylborate into the membrane as a negatively charged lipophilic additive. The selectivity coefficients of various interfering ions were determined using the fixed interference method (FIM). The membrane reveals good selectivity for nickel ions over the other metal ions investigated. The lifetime of this electrode is about one month. This electrode has been applied to the determination of nickel ions in wastewater from the electroplating industry.     

Determination of Nucleic Acids Based on their Resonance Light Scattering Enhancement Effect on Metalloporphyrin Derivatives

A new method for the determination of nucleic acids at nanogram per mL level is proposed based on the enhanced resonance light scattering (RLS) signal resulting from the interaction of metalloporphyrins with nucleic acids. Under optimum conditions, the weak RLS signal of metalloporphyrin is enhanced by nucleic acids, and the enhanced RLS intensity is proportional to the concentration of nucleic acids. The detection limits of calf thymus DNA were 3.5ngmL^–1, 2.9ngmL^–1 and 1.0ngmL^–1 for three metalloporphyrins, respectively. Synthetic samples were determined with satisfactory results.     

Photoluminescence of osmocene and decamethylosmocene

Osmocene (and decamethylosmocene) is characterized by a lowest-energy ligand field triplet which occurs at _max=372nm (374nm) in absorption and 567nm (572nm) in emission. This orange–yellow phosphorescence is rather intense at 77K but is also visible at r.t.     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Electrochemical Behavior of Epinephrine at a Penicillamine Self-Assembled Gold Electrode,and its Analytical Application

The fabrication and electrochemical characteristics of a penicillamine (PCA) self-assembled monolayer modified gold electrode were investigated. The self-assembled electrode shows obvious electrocatalytic activity for the oxidation of epinephrine (EP). In phosphate buffer (pH 7.73), a sensitive oxidation peak was observed at 0.190V with the PCA modified Au electrode. The peak current is proportional to the concentration of EP in the range of 2.0×10^–56.0×10^–4molL^–1 and 5.0×10^–6 2.0×10^–4molL^–1 for cyclic voltammetry (CV) and differential pulse voltammetry (DPV) with the detection limits of 1.8×10^–7 and 1.3×10^–7molL^–1, respectively. The possible reaction mechanism is also discussed. The PCA self-assembled monolayer modified gold electrode is highly stable and can be applied to the determination of EP in practical injection samples. Application is simple, rapid and produces accurate results.     

Kinetics of formation,dissociation and equilibrium constants of pentacyanoaquoruthenate(II) with heterocycles

The kinetics of formation and dissociation reactions of [Ru(CN)₅L]^3– with a series of heterocyclic ligands were studied in aqueous media. In this presence of an excess of heterocycle, the observed second order rate constants were calculated from the k_obs versus [ligand] plot at =0.100m NaClO₄. Activation parameters for the formation reactions (H=28±7kJmol^–1 and S=140±35JK^–1mol^–1) are comparable for all systems, indicating a common mechanism. The kinetics of exchange of coordinated heterocycles for 1,3,5-triazine yielded a rate saturation typical of a limiting dissociative mechanism. Activation parameters of the limiting first order specific rate of dissociation reactions were H=85±7kJmol^–1 and S=18±4JK^–1mol^–1. Equilibrium constants were calculated from the second order rates of formation and pseudo-first order rates of dissociation reaction.     

Non-Aqueous Capillary Electrophoresis with Indirect Photometric Detection for Direct Analysis of Pb2+, Zn2+ and Cd2+ Ions

A new approach, based on non-aqueous capillary electrophoresis separation and indirect photometric detection, was established for the determination of the transition metal ions Pb²⁺, Zn²⁺ and Cd²⁺. Under optimized conditions, the method produced baseline separation of these three metal ions. The linear range and detection limits were 1050µM, 1.9µM for Cd²⁺; 1050µM, 2.1µM for Zn²⁺; and 20100µM, 3.8µM for Pb²⁺, respectively.     

High-Performance Liquid Chromatographic Determination of Quinolizidine Alkaloids in Radix Sophora Flavescens Using Tris(2,2′-Bipyridyl)Ruthenium(II) Electrochemiluminescence

Electrogenerated chemiluminescences (ECLs) of quinolizidine alkaloids including matrine (MT), sophocarpine (SC), and sophoridine (SRI) are studied. The light emission is caused by an electro-oxidation reaction between Ru(bpy)₃²⁺ and the tertiary amino group on the alkaloid compounds. A thin-layer flow cell equipped with a glassy carbon disk electrode (22.1mm²) at the potential of ⁺1.30V (vs. Ag/AgCl) was applied for ECL observation. MT, SC and SRI were separated and quantitatively determined within 25min by an ODS-80 Ts reversed-phase column with a mobile phase containing 80mmolL^–1 NaH₂PO₄–K₂HPO₄ buffer+acetonitrile (7:3)+40mmolL^–1 sodium dodecyl sulfate (pH 6.5). The determination limit at an S/N of 3 ranged from 3×10^–9gmL^–1 for MT, 6×10^–9gmL^–1 for SC and 1×10^–9gmL^–1 for SRI. The recoveries are from 92 to 108%, with repeatability ranging from 1.3 to 4.5% (relative standard deviation). The method was successfully applied to the determination of quinolizidine alkaloids in Sophora flavescens samples.     

Determination of Na,K, Rb and Cs Distribution in Human Brain Using Neutron Activation Analysis

This study aims to investigate the distribution of Na, K, Rb and Cs in human brains (5 individuals, 12 brain parts, mean age: 75 years). Distribution of the trace metals between lipid fraction and brain tissue was investigated in solvent extraction experiments. Determinations were carried out by instrumental neutron activation analysis. The present results show a rather non-homogeneous distribution for Na and a relatively uniform distribution for K, Rb and Cs. The mean concentrations found are 7440µgNag^–1 dry weight, 12800µgKg^–1, 14µgRbg^–1 and 50ngCsg^–1. A highly significant positive correlation was found between Rb and Cs. Solvent extraction experiments showed that 19% of Rb and 26% of Cs of the total content is located in lipid fraction.     

Solvent Sublation Using Dithizone as a Ligand for Determination of Trace Elements in Water Samples

Solvent sublation was studied as a method of separating and pre-concentrating traces of Zn(II), Cd(II) and Cu(II) as diphenylthiocarbazone (dithizone) complexes for their determination. The experimental conditions, such as pH of solution, amount of dithizone as ligand, stirring time, gas flow rate and flotation time, were optimized. Different non-ionic surfactants and types of organic solvents were optimized for efficient sublation. The analyte ions in a 350mL sample were complexed as metal-dithizone complexes by adding 10mL of 0.084% dithizone, 0.5mL of 0.1% nonylphenol polyoxyethylene ether (NP) and 10mL of pH 4.3 potassium hydrogen phthalate-sodium hydroxide buffer solution. The solution was stirred with a mechanical stirrer for 30min. It was transferred to a flotation cell, and the complexes were floated by bubbling air and extracted into 10mL of methylisobutyl ketone (MIBK) on the surface of the aqueous solution. The analytes in the organic phase were determined by flame atomic absorption spectrometry (F-AAS) for Zn(II) and by graphite furnace atomic absorption spectrometry (GF-AAS) for Cd(II) and Cu(II). The proposed method was applied to determine Zn(II), Cd(II) and Cu(II) in real water samples; the enrichment factor was more than 37, the RSD was less than 4.26%, recoveries ranged from 92.7 to 107.3%, and the detection limits were 1.0µgL^–1 for Zn(II), 0.006µgL^–1 for Cd(II) and 0.06µgL^–1 for Cu(II). The results obtained were satisfactory.     

The Electrochemical Behavior of p-Aminophenol at a ω-Mercaptopropionic Acid Self-Assembled Gold Electrode

A -mercaptopropionic acid (MPA) self-assembled monolayer modified electrode (MPA/SAM/Au) on a gold electrode has been fabricated. The characterization of the MPA/SAM/Au was investigated using attenuated total reflection-fourier transform infrared (ATR-FTIR) and A.C. impedance. The electrochemical behaviors of p-aminophenol (p-AP) were studied at the MPA/SAM/Au by cyclic voltammetry and semi-derivative voltammetry (SDV) in BR buffer solution. The modified electrode shows excellent electrocatalytic activity for the redox of p-AP and accelerates the electron transfer rate. The diffusion coefficient (D) is 4.55×10^–6cm²s^–1. The oxidative peak current increases linearly with the concentration of p-AP in the range of 4.0×10^–88×10^–6molL^–1 and 1.0×10^–52×10^–4molL^–1 by square wave voltammetry response, respectively. The detection limit (three times the signal blank/slope) is up to 1.2×10^–8molL^–1. The modified electrode is able to eliminate the interference of p-benzenediol, o-benzenediol and o-AP at a 40-, 90- or 70-fold concentration of p-AP, and it has been satisfactorily used for the determination of the real sample.     

Brightness Reversion of Mechanical Pulps. Part XVII: Diffuse Reflectance Study on Brightness Stabilization by Additives Under Various Atmospheres

Brightness reversion of softwood (SW) and hardwood (HW) bleached chemithermomechanical pulps (BCTMP) with a 300–400nm light source under argon, oxygen, and air were studied in the absence and presence of UV-screens using UV–Vis reflectance difference spectroscopy. The UV-Vis difference absorption spectra of control SW and HW BCTMP testsheets indicate that as the concentration of atmospheric oxygen is increased, the absorption at max 360nm increases and a blue shift occurs. In all of the cases studied, brightness reversion was observed to occur under an argon atmosphere. The addition of benzophenone and benzotriazole additives to BCTMP testsheets resulted in a significant decrease in formation of chromophores absorbed at 400nm and 360nm. The possible mechanisms contributing to these effects are discussed in terms of the photoformation of lignin chromophoric structures.