微乳法制备纳米TiO2 /SiO2的结构及光催化研究

Nanosized TiO₂ and TiO₂/SiO₂ particles were prepared by hydrolysis of tetrabutyl titanate (TBOT) and tetraethyl orthosilicate (TEOS) in the TX-100 reverse microemulsion. These particles were characterized by TG-DSC, XRD, FTIR, TEM，N₂ adsorption-desorption. Their photocatalytic activity was tested by degradation of methyl orange. The result shows that TiO₂/SiO₂ nanoparticles are with a monodispersed spherical phase and a uniform size distribution，and TiO₂ particles are dispersed on the surface of SiO₂. The band for Ti-O-Si vibration in FTIR was observed, the Ti-O-Si bond increased the stability of anatase TiO₂, suppressed the phase transformation of titania from anatase to rutile. And due to the addition of SiO₂, the average size of titania decreased from 38 nm in pure TiO₂ to 5 nm in TiO₂/SiO₂. It was found, under UV light irradiation, TiO₂/SiO₂ particles showed higher activity than pure TiO₂, and TiO₂/SiO₂(1/1) particles showed the highest photocatalytic activity on the photocatalytic decomposition of methyl orange, which was influenced by crystal structure, particle size, crystallinity and Surface area Characteristics.     

微乳法合成纳米SiO2/TiO2及其光催化性能

采用聚乙二醇辛基苯基醚(Triton X-100)/正己醇/环己烷/氨水微乳体系合成了纳米TiO2和SiO2/TiO2复合物,用X射线衍射、红外光谱和透射电镜对其结构进行了表征,并以甲基橙降解评价了其光催化性能,讨论了SiO2/TiO2摩尔比、晶相组成及粒径与光催化活性的关系.结果表明,SiO2/TiO2催化剂中形成了新的Ti-O-Si键和无定形SiO2;在纳米TiO2中复合SiO2能有效抑制锐钛矿向金红石的转变,增加锐钛矿的稳定性,并阻止TiO2晶粒的聚集生长.催化剂的光催化活性随金红石含量的增加而降低,加入适量SiO2能明显提高TiO2的光催化活性,其中摩尔比为1/7的SiO2/TiO2光催化活性最高.     

吸附相反应技术用于不同载体表面纳米TiO2的制备

研究了不同载体对吸附相反应技术制备TiO2粒子的影响, 设计了两种不同表面形貌载体的温度实验(A型SiO2: 粒径20 nm, 比表面积640 m2·g-1; B型SiO2: 粒径12 nm, 比表面积200 m2·g-1), 并用电子能谱仪测定了两种载体表面TiO2含量随温度的变化. 结果表明, 两种载体表面Ti含量都随着温度的升高而减少, 且在一定温度范围内存在着突变, 但A载体突变的温度范围是40-60 ℃, 而B载体为30-50 ℃. TEM表征结果则显示, B表面TiO2粒子要比A表面的均匀. XRD得到的晶粒粒径曲线表明, A 载体表面TiO2晶粒粒径随着温度升高而减小并存在着突变, B载体表面粒子粒径则基本不变. 根据硅胶表面的吸附特性, 提出SiO2吸附的共性导致载体表面Ti含量变化曲线存在着共同点, 而载体内外表面的不同形貌则引起其表面吸附层的形貌以及温度敏感性不同, 最终导致两种载体表面Ti含量、晶粒粒径以及形貌上的差别.     

吸附相反应技术制备TiO2的结晶过程以及光降解气相甲苯

研究了吸附相反应技术制备纳米TiO2的结晶过程, 并探讨了该过程对TiO2光催化活性的影响. 利用XRD测定了不同温度和时间焙烧后TiO2的晶型以及晶粒粒径的变化, 发现即使焙烧温度高达900 ℃, TiO2仍维持纯锐钛矿晶型. 随着焙烧温度的增加, TiO2的晶粒粒径变化不大, 均在7 nm以下, 在焙烧温度高于700 ℃时, 锐钛矿结晶峰的峰面积随温度增加, 峰面积保持不变. 改变焙烧时间基本不影响TiO2的晶型和晶粒粒径, 因而其光催化活性变化也较小. 光降解气相甲苯实验表明, 700 ℃焙烧后样品的催化活性最高, 且优于商用P25光催化剂.     

孔道三维相互连通锐钛矿TiO2-SiO2纳米复合介孔材料的制备及其高光催化活性

本文报道一种孔道三维相互连通锐钛矿TiO2-SiO2纳米复合介孔材料的制备.该介孔材料是以两维六方有序结构、直孔道、锐钛矿70TiO2-30SiO2-950纳米复合介孔材料(于950oC晶化2 h)为前驱体, NaOH为SiO2的刻蚀剂,通过“在孔壁内造孔”的方法获得.我们的策略是采用温和的造孔条件,如稀NaOH溶液,合适的温度与固/液比等.采用X射线衍射(XRD),透射电镜(TEM)和低温N2吸附等技术对样品的介孔结构进行了系统表征.结果表明,墙内孔的密度非常高,孔径均一(平均尺寸3.6 nm),且在三维网络高度连通原孔道,但介孔结构仍保持其完整性.锐钛矿纳米晶粒的结晶度和大小在墙内造孔前后基本保持不变.该材料光催化降解罗丹明B(0.303 min–1)与亚甲基蓝(0.757 min–1)的活性相当高,此活性分别是其母体材料的5.1和5.3倍,甚至是Degussa P25光催化剂的16.5和24.1倍.这充分表明三维连通孔道结构对活性的大幅提高起了关键作用.孔道三维连通式锐钛矿TiO2-SiO2纳米复合介孔材料对上述污染物展现出意想不到的高降解活性,显著高于迄今已报道的金属氧化物基介孔材料对上述污染物的降解活性.更重要的是,该光催化剂具有相当高的稳定性和重复使用性.相信,本方法将为具有超高性能的孔道三维相互连通其它金属氧化物基介孔材料的制备铺平了道路.
　　小角XRD结果表明,母体材料的孔道是两维六方有序结构,在孔壁内造孔之后,样品原有的介孔结构仍保持其规整性.宽角XRD结果显示,二氧化钛的晶相是锐钛矿,晶粒尺寸为10.8 nm.造新孔之后,锐钛矿纳米晶粒的结晶度和大小与母体样品的相比变化不大. TEM结果显示,母体样品的孔壁内没有孔.孔道是两维六方有序排列的直孔道,孔径大小均一(平均尺寸4.1 nm).高分辨透射电镜(TEM)观察揭示,锐钛矿纳米晶粒(平均大小11.3 nm)在孔壁内随机排列,并与无定形SiO2纳米颗粒相互连接,相间共存,形成类似“砖块?水泥砂浆”砌成的孔壁,这种独特的复合骨架结构赋予其很高的稳定性.当一些SiO2纳米颗粒被去除之后, TEM观察显示,孔壁内有密集分布的孔,这些孔取向随机,并在三维方向连通原孔道,但介孔骨架结构仍保持其完整性.墙内孔的大小范围很窄(3.1?4.3 nm),平均大小为3.6 nm.高分辨TEM观察显示,锐钛矿晶粒大小与母体材料内的相比基本未变.上述结果与XRD结果一致.低温N2吸附表征结果显示,母体样品内只有一种孔道,孔径为4.0 nm.去除部分SiO2后的样品内有两种孔道,孔径分别是3.4和4.1 nm.这些结果与TEM的观察吻合.罗丹明B与亚甲基蓝在造孔前后样品内扩散速率评价结果显示,其在三维连通孔道内的扩散速率很高,大约是其母体材料内的5倍以上.这表明相互连通的孔道网络结构非常有利于客体分子在其内扩散.光催化降解性能评价结果显示,罗丹明B与亚甲基蓝在相互连通孔道内降解的速率相当高,分别是其在不连通孔道内的5.1和5.3倍.这充分证明孔道三维相互连通对活性的大幅提高起了关键作用.我们对材料的稳定性和重复使用性作了评价,经过10次循环使用孔道三维相互连通锐钛矿TiO2-SiO2纳米复合介孔材料,其吸附与光催化降解罗丹明B的性能变化不大.这充分证明本文制备的孔道连通复合介孔材料的性能是相当稳定的和可重复使用的.该方法可用于制备具有超高性能的孔道三维相互连通其它金属氧化物基介孔材料,如Nb2O5, Ta2O5等.     

形态结构和光电特性对纳米TiO2光催化性能的影响

采用sol-gel法制备了系列纳米TiO2光催化剂,运用X射线衍射、BET比表面测定、紫外漫反射吸收光谱和表面光电压谱等手段对催化剂进行表征,并以乙烯作为光催化反应的指标反应分子,研究了TiO2纳米晶的性质对于光催化活性的影响.随着焙烧温度的升高,TiO2的晶粒逐渐增大,比表面积下降,晶相由锐钛矿向金红石转变,其吸收带边与光伏响应阈值向长波方向移动,氧化－还原能力降低,降解乙烯的转化率迅速下降.     

Sb掺杂纳米TiO2光催化剂的晶体结构与光催化性能

Nanoscale Sb doped titanium dioxide thin films photocatalyst (Ti1-xSbO2) were obtained from dip-coating sol-gel method. The influence of dopant Sb density on the crystal structure and the phase transformation of the thin films were characterized by X-ray diffraction (XRD) and Raman spectra. The results of XRD showed that as-prepared films were not only in anatase state but also in brookite. The crystalline size was estimated to be around 13.3-20 nm. Raman spectra indicated there coexisted other phases and a transformation from brookite to anatase in the samples doped with 0.2% Sb. After doping a proper amount of Sb, the crystallization rate and the content of the anatase Ti1?xSbO2 in the thin films was clearly enhanced because Sb replaced part of the Ti of TiO2 in the thin films. The anode current density (photocurrent density) and the first order reaction speed constant (k) of thin films doped with 0.2% Sb reached 42.49 1A/cm2 and 0.171 h/cm2 under 254 nm UV illumination, respectively, which is about 11 times and 2 times that of the non-doped TiO2 anode prepared by the same method respectively.     

Raman study of TiO2 role in SiO2-Al2O3-MgO-TiO2-ZnO glass crystallization

Tough glass-ceramic material of special mechanical properties with nanosize crystal phases formed by appropriately controlled crystallization was studied by Raman spectroscopy. It was obtained by TiO2 activated crystallization of Mg-aluminosilicate glass of SiO2-Al2O3-MgO-TiO2-ZnO composition. Crystallization was preceded by a change in the TiO2 structural position and state, which is manifested by a changed color of glass from yellow into blue shortly before the glass transformation (Tg) temperature. Raman spectroscopy was applied to explain the mechanism of this process and to establish the role of TiO2 in the early stage of glass crystallization that precedes a complete crystal phase formation. The starting glasses were found in almost complete disorder, since all bands were weak, broad and dominated by a Bose band at about 90 cm-1. After the sample annealing all bands turned out better resolved and the Bose band practically disappeared, both confirming the amorphous structure reorganization process. A multiplet observed in the vicinity of 150 cm-1 we assigned to the anatase and other titania structures that can be considered prime centers of crystallization. Finally, in the closest neighborhood of the Rayleigh line the low frequency mode characterizing nanoparticles was observed. According to this band theory, the mean size of initial titania crystallites is about 10nm for all samples, but the size distribution varies within factor two among them.     

Size dependence of second-order optical nonlinearity of CdS nanoparticles studied by hyper-Rayleigh scattering

Rutile TiO(2) particles were partly dissolved into aqueous solutions of H(2)SO(4), and the Ti(4+) ions were reprecipitated by adding NH(3) aq. Rutile-anatase coupled TiO(2) particles were prepared by heating the solid recovered after centrifugation of the suspension. The content of anatase (c(A), wt%) could be controlled arbitrarily by changing the dissolved amount of rutile. The photocatalytic activity for the gas-phase oxidation of acetaldehyde was evaluated. The first-order rate constant, k, strongly depended on both c(A) and heating temperature (T(c)), increasing with an increase in T(c) at T(c)相似文献   

溶胶法制备的二氧化硅与二氧化钛复合薄膜的性能

在室温下, 采用溶胶法在玻璃基板上制备了厚度约为100 nm的均匀、透明的纳米SiO2-TiO2复合薄膜.研究了不同温度处理后薄膜的超亲水性、光催化能力等光致活性.通过XPS对薄膜表面及近表面元素的化学态的研究发现, Ti在表面及近表面不仅以Ti4＋形式存在, 也存在少量Ti3＋.紫外光照射后, 部分Ti4＋ 转变成了Ti3＋. XRD研究表明, 该薄膜中的TiO2主要以锐钛矿形式存在, 而且其晶粒大小为14～20 nm.用AFM研究了SiO2-TiO2薄膜的表面形貌及不同的温度处理对TiO2颗粒大小的影响.     

Synthesis of uniform anatase TiO2 nanoparticles by gel-sol method. 3. Formation process and size control

Uniform anatase-type TiO(2) nanoparticles were prepared by the gel-sol process from a condensed Ti(OH)(4) gel preformed by the hydrolysis of a Ti-triethanolamine (TEOA) complex. The particle size of the anatase TiO(2) was increased from ca. 5 to 30 nm with pH increasing from 0.6 to 12 by aging the Ti(OH)(4) gel at 140 degrees C for 72 h, while the yield of the anatase TiO(2), 100% below pH 9.6, started to decrease from pH 10, to 67% at pH 11.5 and only 9% at pH 12.2. These results reveal a significant reduction of the nucleation rate of the anatase TiO(2) with increasing pH, as is explained by the reduction of the concentration of a precursor complex, Ti(OH)(3)(+), and the adsorption of hydroxide ion onto the embryos of TiO(2). Triethanolamine appeared to enhance the pH effect on the nucleation rate of anatase TiO(2) particles by adsorption onto their embryos, leading to the wide range of the size control. Triethanolamine was also found to act as a shape controller of the anatase TiO(2) particles for yielding ellipsoidal particles from Ti(OH)(4) gel at a relatively high pH above 11. The particle size was also controlled by seeding of anatase TiO(2). Moreover, the seeding experiment suggested that the rate-determining step of the gel-sol process was not the dissolution of the hydroxide gel, but the deposition of the monomeric precursor from the solution phase.     

表面键联型TiO2/SiO2固定化催化剂的结构及催化性能

 采用浸渍法制备了表面键联型TiO2／SiO2固定化光催化剂．XRD\r\n,FT－IR,XPS和BET比表面积测定结果表明,TiO2通过Ti－O－Si联结\r\n负载于多孔硅胶的表面,由此提出TiO2／SiO2的结构模型．考察了多孔\r\n硅胶的粒度及氧化钛负载量对催化剂活性的影响．对活性艳红K－2G（\r\nR15）的光催化脱色反应,最佳的光催化剂30％TiO2／SiO2（Ims30）比\r\nB－TiO2粉末的催化速率快3倍．随着载体粒度的减小,催化剂的比表面\r\n积增大,催化活性升高;多孔硅胶不仅起着支持体的作用,而且具有分\r\n散的作用;多孔硅胶具有很好的透光性．经ξ－电位测定,所制备催化\r\n剂的等电点为3．0pH单位,表明催化剂表面呈酸性．     

Structural characterization of CeO(2)-ZrO(2)/TiO(2) and V(2)O(5)/CeO(2)-ZrO(2)/TiO(2) mixed oxide catalysts by XRD, Raman spectroscopy, HREM, and other techniques

Structural characteristics of CeO(2)-ZrO(2)/TiO(2) (CZ/T) and V(2)O(5)/CeO(2)-ZrO(2)/TiO(2) (V/CZ/T) mixed oxide catalysts have been investigated using X-ray diffraction (XRD), BET surface area, Raman spectroscopy (RS), and high-resolution transmission electron microscopy (HREM) techniques. The CeO(2)-ZrO(2) (1:1 mole ratio) solid solution was deposited over a finely powdered TiO(2) support by a deposition precipitation method. A nominal 5 wt % V(2)O(5) was impregnated over the calcined (773 K) CZ/T mixed oxide carrier by a wet impregnation technique. The obtained CZ/T and V/CZ/T samples were further subjected to thermal treatments from 773 to 1073 K to understand the dispersion and temperature stability of these materials. In the case of CZ/T samples, the XRD results suggest the formation of different cubic and tetragonal Ce-Zr-oxide phases, Ce(0.75)Zr(0.25)O(2), Ce(0.6)Zr(0.4)O(2), Ce(0.5)Zr(0.5)O(2), and Ce(0.16)Zr(0.84)O(2) in varying proportions depending on the treatment temperature. With increasing calcination temperature from 773 to 1073 K, the intensity of the lines pertaining to cubic Ce(0.6)Zr(0.4)O(2) and Ce(0.5)Zr(0.5)O(2) phases increased at the expense of cubic Ce(0.75)Zr(0.25)O(2), indicating more incorporation of zirconia into the ceria lattice. The TiO(2) was mainly in the anatase form whose crystallite size also increased with increasing treatment temperature. A better crystallization and more incorporation of zirconia into the ceria lattice was noted when CZ/T was impregnated with V(2)O(5). However, no crystalline V(2)O(5) could be seen from both XRD and RS measurements. In particular, a preferential formation of CeVO(4) compound and an intense tetragonal Ce(0.16)Zr(0.84)O(2) phase were noted beyond 873 K. The HREM results indicate, in the case of CZ/T samples, a well-dispersed Ce-Zr-oxide of the size approximately 5 nm over the bigger crystals ( approximately 40 nm) of TiO(2) when treated at 873 K. The exact structural features of these crystals as determined by digital diffraction analysis of experimental images reveal that the Ce-Zr-oxides are mainly in the cubic fluorite geometry and the TiO(2) is in anatase form. A better crystallization of Ce-Zr-oxides ( approximately 8 nm) over the surface of bigger crystals of TiO(2) was noted at 1073 K. A further enhancement in the crystallite size and zirconia-rich tetragonal phase was noted in the case of V/CZ/T samples. Further, the structure of CeVO(4) formed was also clearly identified in conformity with XRD and RS results.     

SiO2负载的TiO2光催化剂可见光催化降解染料污染物

 采用酸催化溶胶-凝胶法制备了SiO2负载的TiO2光催化剂,考察了制备条件对负载型TiO2光催化剂的晶相、结构、比表面积和可见光催化活性的影响. 结果表明,采用SiO2为载体时,TiO2以纳米颗粒的形态分散在载体表面,负载型TiO2/SiO2催化剂的比表面积大、等电点低而且热稳定性能良好. 偶氮染料酸性橙7的可见光催化降解实验结果表明,染料污染物在催化剂表面的吸附是影响催化剂可见光催化活性的重要因素. 与试剂TiO2样品相比,负载型TiO2/SiO2光催化剂具有更好的光催化活性和沉降性能.     

Y掺杂纳米TiO2的合成及晶型转变过程

溶胶-凝胶;锐钛型;金红石型;Y掺杂纳米TiO2的合成及晶型转变过程     

氮和碳共掺杂TiO2纳米晶的制备及可见光催化性能

以钛酸四丁酯为钛源, 冰醋酸为抑制剂, 超细铵盐为固体载体, 采用新型溶胶-凝胶法制备了氮和碳共掺杂TiO2纳米晶(N-C-TiO2) 光催化剂. 透射电子显微镜(TEM)结果表明, N-C-TiO2样品颗粒均匀, 尺寸细小, 且分散性好; 热失重分析(TGA)、 X射线粉末衍射(XRD)和X射线光电子能谱(XPS)研究结果表明, 复合干凝胶经低温热处理, 使铵盐载体分解、 挥发去除, 样品为单一的锐钛矿相, N和C原子扩散进入晶格结点或间隙位置, 与TiO2化学键结合; 氮气等温吸附-脱附结果表明, 样品比表面积高达356 m2/g, 孔体积为0.27 mL/g. 以氙灯为可见光光源, 罗丹明B水溶液为模拟污染物, P25为参比催化剂, 在辐射强度为100 mW/cm2的可见光照射条件下, N-C-TiO2具有很高的光催化活性, 其可见光催化活性明显高于P25.     

A New Method for Preparing Ti-Si Mixed Oxides

Ti-Si mixed oxides with different TiO2 content were prepared by sol-gel one step hydrolysis, using TiCl4 as the precursor. The samples were characterized by BET, FT-IR and XRD. The results indicated that titanium is in fourfold coordination with oxygen in the SiO4^4- in mixed oxides, form the bond of Ti-O-Si, and the low titania materials are mixed on an atomic scale.The phase of anatase appeared when TiO2 content is up to 80%. The mixed oxides had high specific surface areas up to 681.5 m^2/g. 10TiSi is a better support than SiO2 in the reaction of CO oxidation.     

二氧化钛系列光催化剂的拉曼光谱

采用溶胶-凝胶法制备了TiO₂粉体和薄膜光催化剂.使用FT-Raman光谱和激光共聚焦拉曼光谱研究了粉体和薄膜的拉曼光谱,探讨了热处理条件、Fe³⁺掺杂和以硅胶为载体的薄膜化所引起的TiO₂结构变化.结果表明,TiO₂在350℃存在由无定形向锐钛矿相的转变,600℃下存在锐钛矿相向金红石相的转变,750℃下完全转变为金红石相;掺杂会引起TiO₂的晶格畸变,导致拉曼谱峰宽化;以硅胶为载体的TiO₂负载薄膜的部分拉曼谱峰与粉体相比,有一定的位移和宽化.     

Characterization of Pore Structure and Coordination of Titanium in TiO(2) and SiO(2)-TiO(2) Sol-Pillared Clays

Titania sol-pillared clay (TiO(2) PILC) and silica-titania sol-pillared clay (SiO(2)-TiO(2) PILC) were synthesized by the sol-gel method. Supercritical drying (SCD) and treatment with quaternary ammonium surfactants were used to tailor the pore structure of the resulting clay. It was found that SCD approach increased the external surface area of the PILCs dramatically and that treatment with surfactants could be used to tailor pore size because the mesopore formation in the galleries between the clay layers follows the templating mechanism as observed in the synthesis of MCM-41 materials. Highly mesoporous solids were thus obtained. In calcined TiO(2) PILC, ultrafine crystallites in anatase phase, which are active for photocatalytic oxidation of organics, were observed. In SiO(2)-TiO(2) PILCs and their derivatives, titanium was highly dispersed in the matrix of silica and no crystal phase was observed. The highly dispersed titanium sites are good catalytic centers for selective oxidation of organic compounds. Copyright 2001 Academic Press.     

Microwave-solvothermal synthesis of various polymorphs of nanostructured TiO2 in different alcohol media and their lithium ion storage properties

The various polymorphs (anatase, rutile, and brookite) of TiO(2) with different nanomorphologies have been synthesized by a facile microwave-assisted solvothermal process without surfactants, employing TiCl(4) or TiCl(3) as precursors in various alcohol (ethanol, propanol, butanol, and octanol) media. The samples have been characterized by X-ray diffraction (XRD), electron microscopy, and Brunauer-Emmett-Teller (BET) surface area analysis. The Ti/Cl ion concentration, reaction pH, and size of the alcohol molecule are found to control the morphology, crystal structure, and crystallite size of the TiO(2) particles. Among the various TiO(2) polymorphs synthesized, the rutile TiO(2) spheres built up of nanorods that were synthesized with TiCl(4) in octanol have an average pore size and surface area of, respectively, 5 nm and 404 m(2)/g and exhibit the best electrochemical performance with a capacity of >200 mAh/g after 100 cycles and high rate capability. The excellent electrochemical properties originate from the nanorod-building morphology and mesoporosity of TiO(2) spheres that provide good electrical contact, accommodates the strain smoothly, and facilitates facile lithium-ion diffusion.