聚能炸药逆向环形起爆形成高速射流研究

设计了一种长径比为 0 .375 ,罩锥角为 12 0的大锥角小长径比聚能装药。利用闪光X射线摄影技术观察了小长径比聚能装药正向起爆时形成的射流图象以及逆向起爆时药型罩的压垮图象和射流图象。给出了形成射流的头部速度、射流的质量分布等射流特性参数。试验的聚能装药逆向起爆时射流头部速度为 7.48km/s,而正向起爆时仅为 4.34km/s。试验研究表明通过逆向环形起爆 ,小长径比聚能装药获得高速射流是可行的。     

串联EFP装药结构参数优化实验研究

为了在大块度障碍物上快速开孔且孔深和孔径符合要求,提出了一种前后两级均为爆炸成形弹丸 (EFP)装药的新型串联聚能装药结构。分析了装药结构参数对串联EFP侵彻威力的影响,并在此基础上分 别开展了串联EFP装药在不同装药间距与起爆延时条件下侵彻45钢靶实验。实验表明,优化后的串联EFP 装药结构使前后两级EFP装药的侵彻效率大大提高,能对硬目标进行有效破孔。     

夹层聚能装药作用过程的数值模拟

基于凝聚炸药冲击起爆的Lee-Tarver模型,利用AUTODYN有限元计算软件对夹层聚能装药作用过程进行了数值模拟。分别对夹层聚能装药爆轰波形传播过程及其特性参数进行了数值计算,对典型聚能装药采用单一结构装药、夹层装药的射流成型过程进行了数值研究,最后对不同爆速炸药匹配关系的夹层聚能装药射流参数进行了计算分析。计算结果表明,相对于单一结构装药,夹层装药射流头部速度提高了20%,夹层聚能装药能有效提高聚能金属射流头部速度、提高侵彻深度、增加炸药装药的作功能力。     

固体火箭推进剂起爆技术

针对便携式防空导弹的聚醚复合推进剂进行了余药起爆试验。试验表明,在聚能装药起爆器作用下成功地起爆了推进剂药柱。该技术对战斗部 发动机一体化设计有重要应用价值。     

间隔靶对射流侵彻影响的数值模拟和实验研究

对某聚能装药射流侵彻靶板的过程进行了数值模拟 ,得出其碰撞点附近应力分布与传统理论相符 ,侵彻深度与实验结果及工程计算结果基本相符 ;分别对该聚能装药侵彻连续靶和间隔靶的过程进行了数值模拟 ,数值模拟结果显示间隔靶的侵彻深度明显低于连续靶的侵彻深度 ,这说明侵彻开坑阶段的能耗侵深比远大于准定常阶段。为了验证间隔靶对射流侵彻的影响 ,用另一聚能装药分别对连续靶和间隔靶进行了侵彻实验 ,并排除了炸高的影响。实验结果也表明 ,间隔靶对射流侵彻的确存在着不利影响。还结合数值模拟及实验结果对传统的侵彻公式进行了修正。     

基于聚能射流的岩石定向劈裂机制

基于岩石材料脆性断裂模型分析,从提高炸药能量向岩石断裂表面能转换效率的角度,提出采用预切槽和多点聚能射流冲击岩石进行裂纹引导与扩展,实现岩石定向劈裂。设计了一种可用于岩石劈裂的聚能装药,利用数值计算方法研究了岩石类脆性材料在聚能射流冲击作用下的定向劈裂机制,并计算比较了不同形状金属杆射流对岩体的冲击劈裂效果。分析计算该聚能装药射流形成与岩石的侵彻断裂过程,得出用于岩石劈裂的最佳聚能装药结构与炸高。实验成功用2枚聚能装药将岩石试块按预制方向劈裂,测试获得的岩石表面应力峰值约0.5～0.8 MPa。结果表明,采用该聚能装药在25 mm炸高下能够形成长径比约1∶3的楔形金属杆射流,沿着控界面预先设计的切槽方向,多点设置聚能装药,同时起爆后形成楔形金属杆射流冲击岩石,产生了较好的定向劈裂效果。该方法将爆炸能量精准导入控界面并有效地转换成岩石断裂表面能,从而提升了岩石定向劈裂的效果及炸药的能量利用率,研究结果可为大范围岩体开挖精确控界爆破切割装置设计及降低工程爆破危害提供参考。     

大锥角聚能装药射流形成及对多层靶侵彻的数值模拟研究

运用改进的网格线示踪点法MOCL(MarkOnCellLine)二维多流体欧拉程序 ,对大锥角聚能装药射流的形成及侵彻多层金属靶的全过程进行了数值模拟研究 ,计算结果与试验结果较吻合。这种连贯性的模拟能力避免了数值计算中对射流的许多人为假定。计算和试验结果表明 ,该聚能装药所形成的射流质量约占整个药型罩质量的 32 % ,兼有聚能射流和爆炸成型弹丸的特点 ,更适合于穿透多层大间隔金属靶。     

约束状态下聚能杆流对混凝土作用的实验研究

聚能杆流是多级串联战斗部次级装药的常用聚能侵彻体.基于两种典型的聚能装药结构,设计加工了有不同直径和深度预制约束孔的C35混凝土靶板,开展了(Φ60mm亚半球和K装药在不同约束状态侵彻毁伤混凝土对比实验研究.结果表明,两种聚能杆流都可在混凝土孔约束状态下形成大且深的侵彻孔;随约束孔径增大,侵彻深度先减小而后增加;随约束...     

反钢筋混凝土串联聚能装药技术研究

根据钢筋混凝土目标的特点,提出了一种高速杆流与低速杆流相结合的新型串联聚能装药结构。利用有限元软件分别对前级装药、后级装药的成型过程进行了数值仿真。在此基础上开展了系列串联聚能装药毁伤钢筋混凝土目标的静破甲实验。结果表明:该串联装药可有效提高对钢筋混凝土目标的毁伤能力,能起到对钢筋混凝土的扩孔作用。实验和数值仿真计算结果都表明该串联装药在对付钢筋混凝土、机场跑道、多层间隔靶等反硬目标串联型战斗部中有较好的应用前景。     

三锥S形聚能装药及其射流的性能分析

简介了一种新设计的三维S形聚能装药,并用MFD程序及多虚拟原点侵彻理论数值和解析地分析了射流的特性及侵彻能力。文中还给出了这种装药与单、双锥罩聚能装药的对比、理论预估与实验结果的对比。     

Impact non-pénétrant sur le thorax : influence de la courbure sur la propagation des ondesNonpenetrating impact on the thorax: influence of curvature on wave propagation

Theoretical studies of the propagation of impact waves through the thorax are needed to improve the design of bulletproof jackets and blast protections (Fung in ‘Biomechanics Motions, Flow, Stress, and Growth’, Springer-Verlag, 1990; Cooper et al., J. Trauma 40 (1996) S38–S41). The influence of the weak acoustic coupling at the interface between the thoracic wall and the lung were described in (Grimal et al., C. R. Acad. Sci. IIB 329 (2001) 655–662); in this work, we study, within the frame of elastodynamics and with an approximate analytical method, the effects of the curvature of this interface. Results are given in terms of strain energy for the pressure wave, transmitted or converted. Focalisation of energy in the medium representing the lung is important for curvatures measured in humans. To cite this article: Q. Grimal et al., C. R. Mecanique 330 (2002) 569–574.     

Vérification expérimentale de la relation de réciprocité d'Onsager pour l'électro-osmose et l'électro-filtration dans une argile naturelleExperimental verification of the Onsager's reciprocal relations for electro-osmosis and electro-filtration phenomena on a saturated clay

This Note is devoted to the experimental verification of the Onsager's reciprocal relations in the particular case of electro-osmosis and electro-filtration. A special set up has been designed to carry out the measurements of both the electro-osmotic permeability and the streaming potential. This has been performed by using a natural material i.e., saturated kaolinite. To cite this article: K. Beddiar et al., C. R. Mecanique 330 (2002) 893–898.     

Use specification of multiscale materials for life spanned over macro-, micro-, nano-, and pico-scale

Multiscale material intends to enhance the strength and life of mechanical systems by matching the transmitted spatiotemporal energy distribution to the constituents at the different scale, say—macro, micro, nano, and pico,—, depending on the needs. Lower scale entities are, particularly, critical to small size systems. Large structures are less sensitive to microscopic effects. Scale shifting laws will be developed for relating test data from nano-, micro-, and macro-specimens. The benefit of reinforcement at the lower scale constituents needs to be justified at the macroscopic scale. Filling the void and space in regions of high energy density is considered.Material inhomogeneity interacts with specimen size. Their combined effect is non-equilibrium. Energy exchange between the environment and specimen becomes increasingly more significant as the specimen size is reduced. Perturbation of the operational conditions can further aggravate the situation. Scale transitional functions and/or f_j/j+1 are introduced to quantify these characteristics. They are represented, respectively, by , and (f_mi/ma,f_na/mi,f_pi/na). The abbreviations pi, na, mi, and ma refer to pico, nano, micro and macro.Local damage is assumed to initiate at a small scale, grows to a larger scale, and terminate at an even larger scale. The mechanism of energy absorption and dissipation will be introduced to develop a consistent book keeping system. Compaction of mass density for constituents of size 10⁻¹², 10⁻⁹, 10⁻⁶, 10⁻³ m, will be considered. Energy dissipation at all scales must be accounted for. Dissipations at the smaller scale must not only be included but they must abide by the same physical and mathematical interpretation, in order to avoid inconsistencies when making connections with those at the larger scale where dissipations are eminent.Three fundamental Problems I, II, and III are stated. They correspond to the commonly used service conditions. Reference is made to a Representative Tip (RT), the location where energy absorption and dissipation takes place. The RT can be a crack tip or a particle. At the larger size scales, RT can refer to a region. Scale shifting of results from the very small to the very large is needed to identify the benefit of using multiscale materials.     

Methode zum Messen des Langzeitverhaltens von Thermoplasten

Zusammenfassung Es wird eine neue berührungslose optische Dehnungsmeßeinrichtung für biaxiale Langzeit-Zug- bzw. Torsionsversuche vorgestellt. Die Ergebnisse der Versuche an kugel- und kurzglasfasergefülltem Polyamid 6 (PA6) zeigen, daß dieses System genügend genau arbeitet. Das untersuchte Material weist sowohl im Zugversuch als auch im Torsionsversuch nichtlineares Verhalten auf. Bei überlagerten Zug/Torsions-Belastungen verschieben sich die Dehnungen, verglichen mit denen bei gleicher einaxialer Last zu höheren Werten. Durch die Füllstoffzugabe ergeben sich unterschiedliche Verstärkungseffekte. Die faserverstärkten Proben sind erwartungsgemäß eher in Richtung der Rohrachse verstärkt, während das kugelgefüllte System eine höhere Verstärkungswirkung bei Torsionsbelastung erkennen läßt.

---

A new optical device for strain measurement in long-term tension and torsion tests is presented. The new system has been compared with others and the results of the experiments with glass bead and short, glas-fiber-filled Polyamid 6 show that it works well. With a dead-weight loading machine used it is possible to perform combined tension/torsion creep experiments or simple tension and simple torsion tests. The materials under consideration here exhibit nonlinear behavior in tension as well as in torsion tests. Under combined loading, which is tensile stress with a superimposed torsional stress, or vice versa, the amounts of the strains compared with those of the one-dimensional stress state are increasing. The fillers produce different reinforcement effects. The bead-filled system is stiffer when subjected to a torsional load, which may be explained by different load carrying mechanism in tension and torsion. The glassfiber-filled system is stiffer in axis direction, because the fibers are aligned to a considerable extent by the flow of the melt during molding.

Vortrag gehalten auf der Jahrestagung der Deutschen Rheologischen Gesellschaft, TH Darmstadt, 19.–21. 4. 1989.     

Methode zum Messen des Langzeitverhaltens von Thermoplasten

Zusammenfassung Es wird eine neue berührungslose optische Dehnungsmeßeinrichtung für biaxiale Langzeit-Zug- bzw. Torsionsversuche vorgestellt. Die Ergebnisse der Versuche an kugel- und kurzglasfasergefülltem Polyamid 6 (PA 6) zeigen, daß dieses System genügend genau arbeitet. Das untersuchte Material weist sowohl im Zugversuch als auch im Torsionsversuch nichtlineares Verhalten auf. Bei überlagerten Zug/Torsions-Belastungen verschieben sich die Dehnungen, verglichen mit denen bei gleicher einaxialer Last zu höheren Werten. Durch die Füllstoffzugabe ergeben sich unterschiedliche Verstärkungseffekte. Die faserverstärkten Proben sind erwartungsgemäß eher in Richtung der Rohrachse verstärkt, während das kugelgefüllte System eine höhere Verstärkungswirkung bei Torsionsbelastung erkennen läßt.

---

A new optical device for strain measurement in long-term tension and torsion tests is presented. The new system has been compared with others and the results of the experiments with glass bead and short, glas-fiber-filled Polyamid 6 show that it works well. With a dead-weight loading machine used it is possible to perform combined tension/torsion creep experiments or simple tension and simple torsion tests. The materials under consideration here exhibit nonlinear behavior in tension as well as in torsion tests. Under combined loading, which is tensile stress with a superimposed torsional stress, or vice versa, the amounts of the strains compared with those of the one-dimensional stress state are increasing. The fillers produce different reinforcement effects. The bead-filled system is stiffer when subjected to a torsional load, which may be explained by different load carrying mechanism in tension and torsion. The glass-fiber-filled system is stiffer in axis direction, because the fibers are aligned to a considerable extent by the flow of the melt during molding.

Vortrag gehalten auf der Jahrestagung der Deutschen Rheologischen Gesellschaft, TH Darmstadt, 19.–21. 4. 1989.     

Pont entre les « micro » et « méso » mécaniques des composites stratifiésRelationships between ‘micro’ and ‘meso’ mechanics of laminated composites

A relatively complete bridge is built between the micromechanics of laminates for which there are numerous theoritical and experimental works and the mesomechanics of laminates introduced and developped in particular at Cachan for more than 15 years. At the ‘meso’ scale, the ply and the interface are homogeneized. To cite this article: P. Ladevèze, G. Lubineau, C. R. Mecanique 331 (2003).     

Laser-based measurements of gas-phase chemistry in non-equilibrium pulsed nanosecond discharges

Detailed experimental investigation of a non-equilibrium nanosecond pulsed discharge in premixed CH₄/air mixtures at atmospheric pressure has been carried out. The experiments demonstrated significant reductions in ignition delay and increased lean burn capability relative to conventional spark ignition. Advanced laser diagnostics have been used to identify the physical processes which lead to these improvements. The electron temperature and density properties were measured using laser Thomson scattering (LTS). Temperature measurements were performed using N₂ CARS thermometry to quantify the energy transfer in the gas mixture. Effect of the discharge on the local temperature shows the existence of the ignition of the gas mixture for equivalence ratio between 0.7 and 1.3. Fast development of a flame kernel is then observed. The experiment also shows that the flame can be sustained above the discharge due the repetitive ignition of the flame at the plasma repetition rate. Finally, OH and CH PLIF experiments were performed to confirm the large OH and CH streamer-induced production over the discharge volume. To cite this article: F. Grisch et al., C. R. Mecanique 337 (2009).     

Viscoelastic properties of polymerlike reverse micelles

A dramatic increase in the viscosity of reverse micellar solutions of lecithin in a variety of organic solvents of up to a factor of 10⁶ upon the addition of a small amount of water can be observed. The formation of viscoelastic solutions can be explained by a water-induced aggregation of lecithin molecules into flexible cylindrical reverse micelles and the subsequent formation of a transient network of entangled micelles. The viscoelastic properties of these solutions are characterized as a function of water content and temperature for different organic solvents by means of dynamic shear viscosity measurements. The results are interpreted by making analogies to the behavior of semidilute polymer solutions and living polymers.Dedicated to Prof. Dr. J. Meissner on the occasion of his 60th birthday.     

Lie–Bäcklund and Noether Symmetries with Applications

New identities relating the Euler–Lagrange, Lie–Bäcklund and Noether operators are obtained. Some important results are shown to be consequences of these fundamental identities. Furthermore, we generalise an interesting example presented by Noether in her celebrated paper and prove that any Noether symmetry is equivalent to a strict Noether symmetry, i.e. a Noether symmetry with zero divergence. We then use the symmetry based results deduced from the new identities to construct Lagrangians for partial differential equations. In particular, we show how the knowledge of a symmetry and its corresponding conservation law of a given partial differential equation can be utilised to construct a Lagrangian for the equation. Several examples are given.