Zn掺杂β-Ga2O3薄膜的制备和特性研究

β-Ga₂O₃是一种宽带隙半导体材料,能带宽度E_g≈5.0eV,在光学和光电子学领域有广泛的应用。用射频磁控溅射方法在Si衬底和远紫外光学石英玻璃衬底制备了本征β-Ga₂O₃薄膜及Zn掺杂β-Ga₂O₃薄膜,用紫外 可见分光光度计、X射线衍射仪、荧光分光光度计对本征β-Ga₂O₃薄膜及Zn掺杂β-Ga₂O₃薄膜的光学透过、光学吸收、结构和光致发光进行了测量,研究了Zn掺杂和热退火对薄膜结构和光学性质的影响。退火后的β-Ga₂O₃薄膜为多晶结构,与本征β-Ga₂O₃薄膜相比,Zn掺杂β-Ga₂O₃薄膜的β-Ga₂O₃(111)衍射峰强度变小,结晶性变差,衍射峰位从35.69°减小至35.66°。退火后的Zn掺杂β-Ga₂O₃薄膜的光学带隙变窄,光学透过降低,光学吸收增强,出现了近边吸收,薄膜的紫外、蓝光及绿光发射增强。表明退火后Zn掺杂β-Ga₂O₃薄膜中的Zn原子被激活充当受主。     

Cu掺杂Ga2O3薄膜的光学性能

采用射频磁控溅射和N2气氛退火处理制备了多晶Ga2O3薄膜和Cu掺杂Ga2O3薄膜.用X射线衍射仪、紫外-可见分光光度计、荧光光谱仪对Ga2O3薄膜和Cu掺杂Ga2O3薄膜的结构和光学性能进行了表征.结果表明,Cu掺杂后Ga2O3薄膜的结晶质量变差,透过率明显降低,吸收率增加,光学带隙减小.本征Ga2O3薄膜在紫外、蓝光和绿光出现了发光带,Cu掺杂后紫外和蓝光发射增强,且在475nm处出现了一个新的发光峰.     

过渡金属Fe或Ag掺杂K2Ti6O13的电子结构和光学性质

本文利用基于密度泛函理论（DFT）的第一性原理计算研究了它们的电子结构和光学性质.光学性质的计算结果和实验相一致.结果表明,Fe或Ag掺杂后,K₂Ti₆O₁₃的带隙中出现了杂质带且其带隙值变小,因而使掺杂后的K₂Ti₆O₁₃的吸收边发生红移并实现了其对可见光吸收.其中杂质带主要由Fe 3d态或Ag 4d态与Ti 3d态和O 2p态杂化而成.对于Fe掺杂的K₂Ti₆O₁₃,杂质带位于带隙中间,因此可以作为电子从价带跃迁到导带的桥梁.对于Ag掺杂的K₂Ti₆O₁₃,杂质带位于价带顶附近为受主能级,可以降低光生载流子的复合概率.实验和计算研究表明,通过Fe或Ag的掺杂可以实现了K₂Ti₆O₁₃对可见光的吸收,这对进一步研究K₂Ti₆O₁₃的光学性质具有重要意义.     

溶胶-凝胶法Er2O3薄膜的结构和光学特性

针对稀土Er掺杂Si光源中Er离子掺杂浓度低的问题,采用溶胶-凝胶（Sol-gel）法在Si(100)和SiO2/Si(100)基片上旋涂法制备Er₂O₃光学薄膜,Er离子浓度与以前掺杂方法相比提高了2个数量级.900 ℃热处理获得单一立方结构的Er₂O₃薄膜材料.光致发光（PL）特性研究表明在654 nm波长的激光泵浦下,Er₂O₃薄膜材料获得了1.535 μm的发光峰,并具有较小的温度猝灭1/5.在SiO₂/Si(100)基体上制备的Er2O3薄膜材料的光致发光强度比Si(100)基体上制备的薄膜提高2-3倍.研究结果表明具有强光致发光特性的Er₂O₃薄膜是一种有前景的硅基光源和放大器材料.     

Nd掺杂对Bi4Ti3O12铁电薄膜的微结构和铁电性能的影响

利用溶胶-凝胶法在Pt/Ti/SiO₂/Si(100)衬底上制备了Nd掺杂Bi₄Ti₃O₁₂(Bi_4-xNd_xTi₃O₁₂, x=0.00,0.30,0.45,0.75,0.85,1.00,1.50)铁电薄膜样品.研究了Nd掺杂对Bi₄Ti₃O₁₂薄膜的微结构和铁电性能的影响.研究结果表明:Nd掺杂未改变Bi₄Ti₃O₁₂薄膜的基本晶体结构.在掺杂量x<0.45时,Nd³⁺只取代类钙钛矿层中的A位Bi³⁺.当x=0.45时,样品剩余极化强度达最大值,在270kV·cm^-1的电场下为32.7μC·cm^-2.掺杂量进一步增加时,结构无序度开始明显增大,Nd³⁺开始进入(Bi₂O₂)²⁺层,削弱其绝缘层和空间电荷库的作用,导致材料剩余极化逐渐下降.当掺杂量x达到1.50时,掺杂离子最终破坏(Bi₂O₂)²⁺层的结构,材料发生铁电-顺电相变.     

Gd3Ga5O12:Ag薄膜电致发光材料的制备及其发光性质

研究了Gd₃Ga₅O₁₂:Ag材料的制备及其发光性质.Gd₃Ga₅O₁₂:Ag材料通过固相反应法制得,采用X射线衍射法分 析了材料的结晶度及成分.用电子束蒸发将该材料制备成交流的薄膜电致发光器件,得到了 较好的蓝紫色发光,发光峰分别位于397和467nm.通过对材料的光致发光和激发光谱的研究 和比较,得出397和467nm分别来自于氧空位和Ag⁺的发光.     

Er3+/Yb3+共掺Gd3Sc2Ga3O12晶体的上转换发光

研究了提拉法生长的Er³⁺/Yb³⁺:Gd₃Sc₂Ga₃O₁₂和Er³⁺:Gd₃Sc₂Ga₃O₁₂晶体在室温下320—1700nm范围的吸收光谱和500—750nm范围内的上转换荧光谱,同时对其上转换荧光的可能发生机制、途径以及上转换过程可能对Er^{3+相似文献}   

CdTe太阳电池前电极SnO2:F/SnO2复合薄膜性能分析

减薄CdS窗口层是提高CdS/CdTe太阳电池转换效率的有效途径之一,减薄窗口层会对器件造成不利的影响,因此在减薄了的窗口层与前电极之间引入过渡层非常必要.利用反应磁控溅射法在前电极SnO₂:F薄膜衬底上制备未掺杂的SnO₂薄膜形成过渡层,并将其在N₂/O₂=4 ∶1,550 ℃环境进行了30 min热处理,利用原子力显微镜、X射线衍射仪、紫外分光光度计对复合薄膜热处理前后的形貌、结构、光学性能进行了表征,同时分析了复     

He+辐照对Ga0.94Mn0.06As薄膜铁磁性的改善

离子辐照半导体可以很好的改善半导体材料的磁学性质.用He⁺ 辐照Ga_0.94Mn_0.06As薄膜,可以较方便的调制Ga_0.94Mn_0.06As 薄膜中产生铁磁性载体的浓度.由于空穴居间而导致Ga_0.94Mn_0.06As薄膜的铁磁性, 可以通过He⁺的辐照来得到改善,其结果是Ga_0.94Mn_0.06As薄膜的矫顽力可以增加3倍多. 当He⁺辐照流强增加时, 居里温度和沿着样品面外磁化难轴方向的饱和磁场都减小了. 被辐照的Ga_0.94Mn_0.06As薄膜的电学性质和结构特征显示, He⁺辐照Ga_0.94Mn_0.06As薄膜可以有控制地改善它的铁磁性, 其结果源于He⁺辐照Ga_0.94Mn_0.06As薄膜所诱导产生电缺陷对空穴的补偿, 而不是He⁺辐照改变了Ga_0.94Mn_0.06As薄膜的结构.     

化学法制备的HfO2薄膜的激光损伤阈值研究

 采用化学法制备了HfO₂介质膜，研究了热处理、紫外辐照以及Al₂O₃复合对HfO₂介质膜激光损伤阈值的影响。采用红外光谱（FTIR）和X射线衍射仪对薄膜进行了表征，并用输出波长为1.064 μm、脉宽为10 ns的电光调Q激光系统测试薄膜的激光损伤阈值。实验结果表明：采用150 ℃左右的温度对薄膜进行热处理可以提高薄膜的激光损伤阈值，所获得的薄膜的激光损伤阈值高达42.32 J/cm²，比热处理前的激光损伤阈值提高了82%；无机材料Al₂O₃的适量添加能够提高薄膜的激光损伤阈值，其中HfO₂与Al₂O₃的最佳质量配比约为95∶5；另外，对薄膜进行适当的紫外辐照也可改善HfO₂ 薄膜以及HfO₂-Al₂O₃复合薄膜的抗激光损伤性能。紫外辐照对提高HfO₂-Al₂O₃复合薄膜的激光损伤阈值效果尤为显著，辐照40 min后的激光损伤阈值达到44.33 J/cm²，比紫外辐照前的激光损伤阈值提高了90%。     

Growth of β-Ga2O3 nanorods by ammoniating Ga2O3/V thin films on Si substrate

This paper reports that/3-Ga2O3 nanorods have been synthesized by ammoniating Ga2O3 films on a V middle layer deposited on Si（111） substrates. The synthesized nanorods were confirmed as monoclinic Ga2O3 by x-ray diffraction,Fourier transform infrared spectra. Scanning electron microscopy and transmission electron microscopy reveal that the grown β-Ga2O3 nanorods have a smooth and clean surface with diameters ranging from 100 nm to 200 nm and lengths typically up to 2μm. High resolution TEM and selected-area electron diffraction shows that the nanorods are pure monoclinic Ga2O3 single crystal. The photoluminescence spectrum indicates that the Ga2O3 nanorods have a good emission property. The growth mechanism is discussed briefly.     

Band alignment of Ga2O3/6H-SiC heterojunction

A high-quality Ga₂O₃ thin film is deposited on an SiC substrate to form a heterojunction structure. The band alignment of the Ga₂O₃/6H-SiC heterojunction is studied by using synchrotron radiation photoelectron spectroscopy. The energy band diagram of the Ga₂O₃/6H-SiC heterojunction is obtained by analysing the binding energies of Ga 3d and Si 2p at the surface and the interface of the heterojunction. The valence band offset is experimentally determined to be 2.8 eV and the conduction band offset is calculated to be 0.89 eV, which indicate a type-II band alignment. This provides useful guidance for the application of Ga₂O₃/6H-SiC electronic devices.     

Annealing effects on the optical and structural properties of Al2O3/SiO2 films as UV antireflection coatings on 4H-SiC substrates

Al₂O₃/SiO₂ films have been prepared by electron-beam evaporation as ultraviolet (UV) antireflection coatings on 4H-SiC substrates and annealed at different temperatures. The films were characterized by reflection spectra, ellipsometer system, atomic force microscopy (AFM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. As the annealing temperature increased, the minimum reflectance of the films moved to the shorter wavelength for the variation of refractive indices and the reduction of film thicknesses. The surface grains appeared to get larger in size and the root mean square (RMS) roughness of the annealed films increased with the annealing temperature but was less than that of the as-deposited. The Al₂O₃/SiO₂ films maintained amorphous in microstructure with the increase of the temperature. Meanwhile, the transition and diffusion in film component were found in XPS measurement. These results provided the important references for Al₂O₃/SiO₂ films annealed at reasonable temperatures and prepared as fine antireflection coatings on 4H-SiC-based UV optoelectronic devices.     

Intense ultraviolet and blue upconversion emissions in Yb-Tm codoped stoichiometric Y7O6F9 powder

Stoichiometric Y₇O₆F₉ powder codoped with Yb³⁺-Tm³⁺ was synthesized via co-precipitation and subsequent calcining route. The results of X-ray diffraction and transmission electron microscopy reveal that when the calcining temperature is beyond 800 °C, orthorhombic YF₃ nanoparticles can be completely oxidized into orthorhombic Y₇O₆F₉ powder. Under the excitation of a 980 nm laser, Y₇O₆F₉ powder exhibits multicolor UC emission in regions spanning the UV to the NIR. In addition, the upconversion emission intensities of YF₃, Y₇O₆F₉ and Y₂O₃ powders were compared under the same dopant condition (Yb/Tm=5/0.5 mol%). The low phonon energy revealed by Raman spectra helped to understand the high efficient upconversion emission of Y₇O₆F₉ and the main phonon vibration of Y₇O₆F₉ lies at 472 cm⁻¹, which is far lower that of Y₂O₃ (at 708 cm⁻¹). Our results indicate that orthorhombic rare earth ions doped Y₇O₆F₉ is an efficient matrix for UV and blue UC emission, and has potential applications in color displays, anti-counterfeiting and multicolor fluorescent labels.     

A novel chemical synthesis and characterization of Mn3O4 thin films for supercapacitor application

Mn₃O₄ thin films have been prepared by novel chemical successive ionic layer adsorption and reaction (SILAR) method. Further these films were characterized for their structural, morphological and optical properties by means of X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), field emission scanning electron microscopy (FESEM), wettability test and optical absorption studies. The XRD pattern showed that the Mn₃O₄ films exhibit tetragonal hausmannite structure. Formation of manganese oxide compound was confirmed from FTIR studies. The optical absorption showed existence of direct optical band gap of energy 2.30 eV. Mn₃O₄ film surface showed hydrophilic nature with water contact angle of 55°. The supercapacitive properties of Mn₃O₄ thin film investigated in 1 M Na₂SO₄ electrolyte showed maximum supercapacitance of 314 F g⁻¹ at scan rate 5 mV s⁻¹.     

Optical characteristics of amorphous V2O5 thin films colored by an excimer laser

The V₂O₅ films were prepared by an RF sputtering method, and the amorphous films were colored by an UV excimer laser. The crystallinity of the as-grown V₂O₅ film was degenerated greatly by laser irradiation, as determined by X-ray diffraction (XRD) and Raman studies. The transmission and complex refractive index spectra of the V₂O₅ film were affected by variations in the microstructure, including the surface morphology, crystalline structure, and substoichiometry with an oxygen deficiency. Considerable emissions due to oxygen vacancies and band transition of photoluminescence (PL) peaks were observed, and the peaks were significantly changed after laser irradiation. The variations in the optical properties in both films may be attributed to oxygen deficiency induced by laser irradiation.     

Luminescent properties of green- or red-emitting Eu-doped Sr3Al2O6 for LED

Eu²⁺-doped Sr₃Al₂O₆ (Sr_3−xEu_xAl₂O₆) was synthesized by a solid-state reaction under either H₂ and N₂ atmosphere or CO atmosphere. When H₂ was used as the reducing agent, the phosphor exhibited green emission under near UV excitation, while CO was used as the reducing agent, the phosphor mainly showed red emission under blue light excitation. Both emissions belong to the d-f transition of Eu²⁺ ion. The relationship between the emission wavelengths and the occupation of Eu²⁺ at different crystallographic sites was studied. The preferential substitution of Eu²⁺ into different Sr²⁺ cites at different reaction periods and the substitution rates under different atmospheres were discussed. Finally, green-emitting and red-emitting LEDs were fabricated by coating the phosphor onto near UV- or blue-emitting InGaN chips.     

Anodization of aluminium thin films on pSi and annihilation of strong luminescence from Al2O3

Photoluminescence (PL) of Al₂O₃ films obtained by anodization of thermally evaporated and annealed thin Al films on p⁺⁺Si in 0.3 M oxalic acid has been investigated. Thermal annealing at 200–950 °C under the dry nitrogen atmosphere was used for deactivation of luminescence centres. Luminescence from as grown films was broad and located at 425 nm. This luminescence reached to highest level after annealing at 600 °C. Maximum 10 min was required for full optical activation and prolonged annealing up to 4 h did not change the luminescence intensity. Because of deep levels, absorption band edge of as grown films was shifted to the lower energy which is 3.25 eV. Annealing above 800 °C reduced the PL intensity and this observation was correlated with the blue shift of band edge as the defects annealed out. Disappearing PL intensity and blue shift of band edge absorption after annealing at 950 °C was mainly attributed to the oxygen-related defects and partly to impurities that may be originated from oxalic acid. AFM results did not show any hexagonally ordered holes but uniformly distributed nanosized Al₂O₃ clusters that were clearly seen. XRD measurements on as grown Al₂O₃ showed only [1 1 0] direction of α phase. Debye–Scherer calculation for this line indicates that cluster size is 35.7 nm. XRD and AFM pictures suggest that nanocrystalline Al₂O₃ are embedded in amorphous Al₂O₃.