Ⅱ-Ⅲ混合型裂纹相变增韧分析

本文采用压力敏感准则和松函数法对相变增韧陶瓷Ⅱ-Ⅲ混合型裂纹的增韧效应进行了理论预测。分别给出了静止裂纹和定常扩展裂纹相变塑性屏蔽的理论表达式。结果表明：相变对静止裂纹有甚微的负屏蔽效应，并随KⅢ/KⅡ的比值而波动；相变对定常扩展裂纹的增韧结果除与材料弹性模量、相变尾区高度和相变体积分数有关外，还与KⅢ/KⅡ的比值有关。     

相变增韧陶瓷Ⅱ型裂纹增韧分析

本文采用压力敏感和权函数法，对相变增韧陶瓷Ⅱ型裂纹的增韧效应进行了理论预测。分别给出了静止裂纹和定常扩展裂纹相变性屏蔽的理论表达式，结果表明；相变对静止裂纹无增韧效应，纹尖端屏蔽来自于裂纹扩展尾区的贡献。     

相变增韧陶瓷Ⅲ型裂纹增韧分析

本文采用压力敏感相变准则和权函数法对相变增韧陶瓷Ⅲ型裂纹的增韧效应进行了理论预测,分别给出了静止裂纹和定常扩展裂纹相变塑性屏蔽的理论表达式。结果表明:相变体积膨胀对增韧无贡献,裂尖屏蔽来自于晶格剪切和裂纹扩展尾区的贡献。     

Ⅰ—Ⅲ混合型裂纹相变增韧分析

本文采用压力敏感准则和权函数法对相变增韧陶瓷Ⅰ－Ⅲ混合型裂纹的增韧效应进行了理论预测。分别给出了静止裂纹和定长扩展裂纹相变塑性屏蔽的理论表达式，结果表明：相变对静止裂纹有负屏蔽效应，并随ＫⅢ／ＫⅠ比值的增大而趋于零，对扩展裂纹的增韧结果除与材料的弹性模量，相变尾区高度和相变体积分数有关外，还与ＫⅢ／ＫⅠ的比值有关。     

含弧形微裂纹相变复合陶瓷增韧分析

弧形微裂纹是复合陶瓷内的常见现象,含少量弧形微裂纹复合陶瓷比无裂纹复合陶瓷的韧性更好,而粒子相变能够提高陶瓷的断裂韧性已经得到普遍承认.本文考虑粒子相变与弧形微裂纹的联合效应,建立含弧形微裂纹相变复合陶瓷的混合型裂纹增韧模型.首先应用压力敏感准则和应变能释放率断裂准则,对含弧形微裂纹复合陶瓷的增韧效应进行了理论预测;然后采用权函数法推导出混合型裂纹的增韧结果,分别给出了静止裂纹和稳态扩展裂纹相变塑性屏蔽的理论表达式;最后根据相变区域与弧形微裂纹相之间的关系,分析增韧结果的尺度效应.结果表明:相变对静止裂纹无增韧作用;相变对稳态扩展裂纹的增韧结果除与材料弹性模量、相变尾区高度和相变粒子的体积分数有关外,还与复合陶瓷的颗粒直径和弧形微裂纹的体积分数有关.     

轮轨相互作用下钢轨焊接接头表面裂纹扩展分析

为了分析列车通过钢轨焊接接头时产生的轮轨动态冲击力对钢轨焊接接头表面裂纹扩展特性的影响,首先采用车辆-轨道耦合动力学数值模型计算轮轨垂向力,并建立带表面裂纹的轮轨接触有限元模型;然后将轮轨垂向力结果加载到有限元模型中分析其对裂纹扩展特性的影响。结果表明：在轮轨动态相互作用下,钢轨焊接接头处表面斜裂纹的扩展以剪切模式为主导,裂纹应力强度因子 KI 和应力强度因子范围ΔKII 随着列车速度的增大而增大;裂纹长度和裂纹面摩擦系数对应力强度因子范围ΔKII 影响较大,当裂纹长度从3mm 增加到10mm 时,其ΔKII 增大了204.2%,当裂纹面摩擦系数从0.1增加到0.6时,其ΔKII 减小了153.4%。     

压-剪混合型定常扩展裂纹尖端的弹黏塑性场

假定黏性系数与塑性等效应变率的幂次成反比,考虑其黏性和裂纹面摩擦接触效应 建立了压-剪混合型定常扩展裂纹尖端弹黏塑性场的渐近方程,求得了裂纹尖端场不含应力、应变间 断的数值解. 并讨论了压-剪混合型裂纹数值解随各个参数的变化规律,计算结果 和分析表明,压-剪混合型裂纹尖端场是满塑性的,不含有弹性卸载区,黏性效应是研究扩展裂纹尖端场时的一个重要因素. 无论混合裂纹趋近I型还是趋近II型,静水压力随摩擦系数的增加都是增加的,裂纹面摩擦 效应是阻止裂纹扩展速度的因素,且摩擦作用越强,裂纹尖端场的韧性越高.     

相变增韧陶瓷平面应变Ⅰ型定常扩展裂纹的渐近分析（Ⅰ）

采用Ｂｕｄｉａｎｓｋｙ等人提出的相变增韧陶瓷材料的体膨胀本构关系，利用渐近解法得到该材料平面应变Ⅰ型定常扩展裂纹尖端附近的应力、速率沿角度的分布情况，给出相变区高度和相变造成的韧性增值的计算公式。     

改进的Irwin模型及裂尖塑性区对断裂行为的影响

本文研究了小范围屈服条件下I型裂纹尖端塑性区对断裂行为的影响.Irwin模型假设塑性区外奇异应力场分布是弹性解的平移,并将塑性区的一部分加上原有裂纹视为等效裂纹.这样得到的等效应力强度因子总是大于相应的线弹性解的应力强度因子,这与塑性区的增韧作用相悖.为了考察塑性区对裂纹尖端附近应力分布的影响,本文提出在塑性影响区内,裂纹延长线上奇异应力分布与线弹性奇异应力场静力等效的原则.在此基础上建立了改进的Irwin模型,并导出了衡量塑性区屏蔽效应的显式表达式,定量地解释了塑性区的屏蔽效应,本文结果与基于相变增韧理论的方法得到的结果在趋势上一致.     

压电材料中的微裂纹屏蔽问题分析

分析当主裂纹与一个微裂纹在远场I型力（KI）和远场电位移（Ke)作用下的相互干涉问题,得出了在微裂纹的位置角和方向角周时独立变化时,微裂纹对主裂纹的屏蔽作用的全局使命主裂纹扩展,通过电算还发现Ortiz在各向同性材料和各向异性材料中得出的“微裂纹群对主裂纹最大屏蔽效应产生在微裂纹方向与最大主应力垂直的方向”在压电材料中不再成立,进而提出除Hutchinson指出微裂纹屏蔽效应两个来源（即：材料有效刚度的降低和残余应力的释放）外的另一个来源,微裂纹对主裂砂电场的扰动,在对主微裂纹J积分分析时发现J2积分与J1积分具有同等重要的地位。     

Toughening analysis of mode III crack in transformation toughened ceramics

The fracture toughness enhancement of mode III crack in transformation toughened ceramics such as Ce-TZP and Mg-PSZ is predicted by using a pressure sensitive transformation criterion and the weight function method. The theoretical analyses of the toughening effect for both stationary and steady-state growing crack are given, respectively. The results show that the toughening is only associated with crack growth and there is no toughening effect for stationary crack.The project was supported by the National Science Foundation of China     

Crack growth resistance of shape memory alloys by means of a cohesive zone model

Crack growth resistance of shape memory alloys (SMAs) is dominated by the transformation zone in the vicinity of the crack tip. In this study, the transformation toughening behavior of a slowly propagating crack in an SMA under plane strain conditions and mode I deformation is numerically investigated. A small-scale transformation zone is assumed. A cohesive zone model is implemented to simulate crack growth within a finite element scheme. Resistance curves are obtained for a range of parameters that specify the cohesive traction-separation constitutive law. It is found that the choice of the cohesive strength t₀ has a great influence on the toughening behavior of the material. Moreover, the reversibility of the transformation can significantly reduce the toughening of the alloy. The shape of the initial transformation zone, as well as that of a growing crack is determined. The effect of the Young's moduli ratio of the martensite and austenite phases is examined.     

非均匀铁弹畴变对离面极化压电陶瓷应力强度因子的影响研究

基于文献中报道的试验结果，本文考虑非均匀的畴变过程区，它包含一个位于中心的饱和区和环绕饱和区的渐变区．为了描述外加应力引起的部分铁弹畴变，本文采用一个显式的基于最小能量原理的非均匀畴变准则．考虑离面极化的压电陶瓷，假设其初始极化矢量平行于离面方向．畴变后的电畴位于面内，具体方位由最大释放功来确定．基于非均匀畴变准则，本文给出了裂尖处非均匀畴变区几何及畴变体积分数的分布．并在静止裂纹和稳态扩展裂纹两种特殊情况下计算了铁弹畴变对裂尖处应力强度因子的影响．结果表明：(1) 静止裂纹尖端处的畴变减小了材料的起裂强度；(2) 准静态稳态裂纹附近的畴变增加了材料的断裂强度．且理论预测的R曲线渐近值与试验结果定量吻合．     

On the transformation toughening of a crack along an interface between a shape memory alloy and an isotropic medium

In this study, a bilinear cohesive zone model is employed to describe the transformation toughening behavior of a slowly propagating crack along an interface between a shape memory alloy and a linear elastic or elasto-plastic isotropic material. Small scale transformation zones and plane strain conditions are assumed. The crack growth is numerically simulated within a finite element scheme and its transformation toughening is obtained by means of resistance curves. It is found that the choice of the cohesive strength t₀ and the stress intensity factor phase angle φ greatly influence the toughening behavior of the bimaterial. The presented methodology is generalized for the case of an interface crack between a fiber reinforced shape memory alloy composite and a linear elastic, isotropic material. The effect of the cohesive strength t₀, as well as the fiber volume fraction are examined.     

结构增韧材料在裂纹扩展中的韧度增值

本文分析了由裂纹扩展过程中形成的耗能尾区和桥联段所产生的增韧效应。根据对扩展裂纹的能量积分的贡献,结构增韧材料在裂纹扩展中的韧度增值机制可分解为:尾区体膨胀塑性增韧;尾区剪切屈服带增韧;裂纹面夹杂第二相桥联;未贯穿裂纹的基体桥联。本文结合结构高分子材料和短纤维复合材料等材料体系进行了具体的增韧分析计算。     

The application of the Eshelby equivalent inclusion method for unifying modulus and transformation toughening

When a crack is lodged in an inclusion, both difference between the modulus of the inclusion and matrix material and stress-free transformation strain of the inclusion will cause the near-tip stress intensity factor to be greater (amplification effect) or less (shielding or toughening effect) than that prevailing in a homogeneous material. In this paper, the inclusion may represent a second phase particle in composites and a transformation or microcracked process zone in brittle materials, which may undergo a stress-free transformation strain induced by phase transformation, microcracking, thermal expansion mismatch and so forth. A close form of solution is derived for predicting the toughening (or amplification) effect. The derivation is based on Eshelby equivalent inclusion approach that provides rigorous theoretical basis to unify the modulus and transformation contributions to the near-tip field. As validated by numerical examples, the developed formula has excellent accuracy for different application cases.     

NiTi形状记忆合金裂纹尖端热力耦合行为研究

本文对NiTi形状记忆合金I型裂纹尖端热力耦合行为进行了数值仿真分析和实验验证。建立了包含相变和热力耦合的本构模型,通过有限元计算得到了裂纹尖端附近的纵向应变、马氏体体积分数和温度场分布,依据马氏体相变情况对裂纹尖端有效应力强度因子进行了修正,揭示了加载速率对形状记忆合金裂纹尖端有效应力强度影子的影响规律。参数研究表明,随着加载频率的增加,裂纹尖端附近温度逐渐升高,马氏体相变区域逐渐缩小,有效应力强度因子呈下降趋势,形状记忆合金表现出增韧效应,有助于减缓裂纹扩展。本研究结果对于揭示热力耦合作用下超弹性形状记忆合金疲劳裂纹扩展规律具有重要参考意义。     

Toughness increment by crack growth in toughened structural materials

Material toughening could be furnished by the energy dissipating wakes and bridging segments during crack growth. According to their contributions to the energy integral applicable to a growing crack, the toughening mechanisms are categorized as: dilatational plasticity and induced shear yielding in the crack wakes, bridging due to second inclusion phases, and the matrix bridging caused by wavy crack front. Detailed toughening analysis is pursued for structural polymers and composite materials reinforced by short aligned fibers. Sponsored by the State Education Commission of China and by the Fok Ying-Tung Education Foundation