Unsymmetric Platinum(II) Bis(aryleneethynylene) Complexes as Photosensitizers for Dye‐Sensitized Solar Cells

Four new unsymmetric platinum(II) bis(aryleneethynylene) derivatives have been designed and synthesized, which showed good light‐harvesting capabilities for application as photosensitizers in dye‐sensitized solar cells (DSSCs). The absorption, electrochemical, time‐dependent density functional theory (TD‐DFT), impedance spectroscopic, and photovoltaic properties of these platinum(II)‐based sensitizers have been fully characterized. The optical and TD‐DFT studies show that the incorporation of a strongly electron‐donating group significantly enhances the absorption abilities of the complexes. The maximum absorption wavelength of these four organometallic dyes can be tuned by various structural modifications of the triphenylamine and/or thiophene electron donor, improving the light absorption range up to 650 nm. The photovoltaic performance of these dyes as photosensitizers in mesoporous TiO₂ solar cells was investigated, and a power conversion efficiency as high as 1.57 % was achieved, with an open‐circuit voltage of 0.59 V, short‐circuit current density of 3.63 mA cm^?2, and fill factor of 0.73 under simulated AM 1.5G solar illumination.     

New Amphiphilic Polypyridyl Ruthenium（Ⅱ） Sensitizer and Its Application in Dye-Sensitized Solar Cells

Amphiphilic polypyridyl mthenium（Ⅱ） complex cis-di（isothiocyanato）（4,4＇-di-tert-butyl-2,2＇-bipyridyl）（4,4＇- dicarboxy-2,2＇-bipyridyl）ruthenium（Ⅱ）（K005） has been synthesized and characterized by cyclic voltammetry, ^1H NMR, UV-Vis, and FT-IR spectroscopies. The sensitizer sensitizes TiO2 over a notably broad spectral range due to its intense metal-to-ligand charge-transfer （MLCT） bands at 537 and 418 nm. The photophysical and photochemical studies of K005 were contrasted with those of cis-Ru（dcbpy）2（NCS）2, known as the N3 dye, and the amphiphilic ruthenium（Ⅱ） dye Z907. A reversible couple at E1/2=0.725 V vs. saturated calomel electrode （SCE） with a separation of 0.08 V between the anodic and cathodic peaks, was observed due to the Ru^Ⅱ/Ⅲ couple by cyclic voltammetry. Furthermore, this amphiphilic ruthenium complex was successfully used as sensitizers for dye-sensitized solar cells with the efficiency of 3.72% at the 100 mW·cm^-2 irradiance of air mass 1.5 simulated sunlight without optimization of TiO2 films and the electrolyte.     

Highly Catalytic Carbon Nanotube/Pt Nanohybrid‐Based Transparent Counter Electrode for Efficient Dye‐Sensitized Solar Cells

Low‐cost transparent counter electrodes (CEs) for efficient dye‐sensitized solar cells (DSSCs) are prepared by using nanohybrids of carbon nanotube (CNT)‐supported platinum nanoparticles as highly active catalysts. The nanohybrids, synthesized by an ionic‐liquid‐assisted sonochemical method, are directly deposited on either rigid glass or flexible plastic substrates by a facile electrospray method for operation as CEs. Their electrochemical performances are examined by cyclic voltammetry, current density–voltage characteristics, and electrochemical impedance spectroscopy (EIS) measurements. The CNT/Pt hybrid films exhibit high electrocatalytic activity for I^?/I₃^? with a weak dependence on film thickness. A transparent CNT/Pt hybrid CE film about 100 nm thick with a transparency of about 70 % (at 550 nm) can result in a high power conversion efficiency (η) of over 8.5 %, which is comparable to that of pyrolysis platinum‐based DSSCs, but lower cost. Furthermore, DSSC based on flexible CNT/Pt hybrid CE using indium‐doped tin oxide‐coated polyethylene terephthalate as the substrate also exhibits η=8.43 % with J_sc=16.85 mA cm^?2, V_oc=780 mV, and FF=0.64, and this shows great potential in developing highly efficient flexible DSSCs.     

Peripherally and Axially Carboxylic Acid Substituted Subphthalocyanines for Dye‐Sensitized Solar Cells

A series of subphthalocyanines (SubPcs) bearing a carboxylic acid group either at the peripheral or axial position have been designed and synthesized to investigate the influence of the COOH group positions on the dye‐sensitized solar cell (DSSC) performance. The DSSC devices based on SubPcs with axially substituted carboxylic acid groups showed low photovoltaic performance, whereas peripherally substituted one exhibited higher power conversion efficiency owing to improved injection from LUMO of SubPcs to the TiO₂ conduction band.     

Opp‐Dibenzoporphyrins as a Light‐Harvester for Dye‐Sensitized Solar Cells

New opp‐dibenzoporphyrins were prepared in a concise method that was based on a Pd⁰‐catalyzed cascade reaction. These porphyrins, which contained carboxylic‐acid linker groups on benzene rings that were fused to the porphyrin at their β,β′‐positions, were examined as sensitizers for dye‐sensitized solar cells for the first time. Whereas all of the porphyrins showed solar‐energy‐to‐electricity conversion, an opp‐dibenzoporphyrin with conjugated carboxylic‐acid linkers displayed the highest conversion efficiency and an exceptionally high J_sc value. Cyclic voltammetry of these porphyrins suggested that the fusion of two aromatic benzene rings onto the periphery of the porphyrin lowered the HOMO–LUMO energy gap; the incorporation of a conjugated carboxylic‐acid linker group decreased the HOMO–LUMO gap even further. These CV data are consistent with DFT calculations for these porphyrins and agree well with the UV/Vis absorption‐ and fluorescence spectra of these porphyrins.     

Functionalized Alkynylplatinum(II) Polypyridyl Complexes for Use as Sensitizers in Dye‐Sensitized Solar Cells

A series of platinum(II) alkynyl‐based sensitizers has been synthesized and found to show light‐to‐electricity conversion properties. These dyes were developed as sensitizers for the application in nanocrystalline TiO₂ dye‐sensitized solar cells (DSSCs). Their photophysical and electrochemical properties were studied. The excited‐state property was probed using nanosecond transient absorption spectroscopy, which showed the formation of a charge‐separated state that arises from the intramolecular photoinduced charge transfer from the platinum(II) alkynylbithienylbenzothiadiazole moiety (donor) to the polypyridyl ligand (acceptor). A lifetime of 3.4 μs was observed for the charge‐separated state. A dye‐sensitized solar cell based on one of the complexes showed a short‐circuit photocurrent of 7.12 mA cm^?2, an open circuit voltage of 780 mV, and a fill factor of 0.65, thus giving an overall power conversion efficiency of 3.6 %.     

Photophysical and Electrochemical Properties,and Molecular Structures of Organic Dyes for Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSSCs) based on organic dyes adsorbed on oxide semiconductor electrodes, such as TiO₂, ZnO, or NiO, which have emerged as a new generation of sustainable photovoltaic devices, have attracted much attention from chemists, physicists, and engineers because of enormous scientific interest in not only their construction and operational principles, but also in their high incident‐solar‐light‐to‐electricity conversion efficiency and low cost of production. To develop high‐performance DSSCs, it is important to create efficient organic dye sensitizers, which should be optimized for the photophysical and electrochemical properties of the dyes themselves, with molecular structures that provide good light‐harvesting features, good electron communication between the dye and semiconductor electrode and between the dye and electrolyte, and to control the molecular orientation and arrangement of the dyes on a semiconductor surface. The aim of this Review is not to make a list of a number of organic dye sensitizers developed so far, but to provide a new direction in the epoch‐making molecular design of organic dyes for high photovoltaic performance and long‐term stability of DSSCs, based on the accumulated knowledge of their photophysical and electrochemical properties, and molecular structures of the organic dye sensitizers developed so far.     

A Promising Candidate with D‐A‐A‐A Architecture as an Efficient Sensitizer for Dye‐Sensitized Solar Cells

A series of metal‐free organic dyes with electron‐rich (D) and electron‐deficient units (A) as π linkers have been studied theoretically by means of density functional theory (DFT) and time‐dependent DFT calculations to explore the effects of π spacers on the optical and electronic properties of triphenylamine dyes. The results show that Dye 1 with a structure of D‐A‐A‐A is superior to the typical C218 dye in various key aspects, including the maximum absorption (λ_max=511 nm), the charge‐transfer characteristics (D/Δq/t is 5.49 Å/0.818 e^?/4.41 Å), the driving force for charge‐carrier injection (ΔG_inject=1.35 eV)/dye regeneration (ΔG_regen=0.27 eV), and the lifetime of the first excited state (τ=3.1 ns). It is thus proposed to be a promising candidate in dye‐sensitized solar cell applications.     

Molecular Design Principle of All‐organic Dyes for Dye‐Sensitized Solar Cells

All‐organic dyes have shown promising potential as an effective sensitizer in dye‐sensitized solar cells (DSSCs). The design concept of all‐organic dyes to improve light‐to‐electric‐energy conversion is discussed based on the absorption, electron injection, dye regeneration, and recombination. How the electron‐donor–acceptor‐type framework can provide better light harvesting through bandgap‐tuning and why proper arrangement of acceptor/anchoring groups within a conjugated dye frame is important in suppressing improper charge recombination in DSSCs are discussed. Separating the electron acceptor from the anchoring unit in the donor–acceptor‐type organic dye would be a promising strategy to reduce recombination and improve photocurrent generation.     

Application of the Tris(acetylacetonato)iron(III)/(II) Redox Couple in p‐Type Dye‐Sensitized Solar Cells

An electrolyte based on the tris(acetylacetonato)iron(III)/(II) redox couple ([Fe(acac)₃]^0/1?) was developed for p‐type dye‐sensitized solar cells (DSSCs). Introduction of a NiO blocking layer on the working electrode and the use of chenodeoxycholic acid in the electrolyte enhanced device performance by improving the photocurrent. Devices containing [Fe(acac)₃]^0/1? and a perylene–thiophene–triphenylamine sensitizer (PMI–6T–TPA) have the highest reported short‐circuit current (J_SC=7.65 mA cm^?2), and energy conversion efficiency (2.51 %) for p‐type DSSCs coupled with a fill factor of 0.51 and an open‐circuit voltage V_OC=645 mV. Measurement of the kinetics of dye regeneration by the redox mediator revealed that the process is diffusion limited as the dye‐regeneration rate constant (1.7×10⁸ M ^?1 s^?1) is very close to the maximum theoretical rate constant of 3.3×10⁸ M ^?1 s^?1. Consequently, a very high dye‐regeneration yield (>99 %) could be calculated for these devices.     

Computational Design of Cyclic Nitroxides as Efficient Redox Mediators for Dye‐Sensitized Solar Cells

Cyclic nitroxide radicals represent promising alternatives to the iodine‐based redox mediator commonly used in dye‐sensitized solar cells (DSSCs). To date DSSCs with nitroxide‐based redox mediators have achieved energy conversion efficiencies of just over 5 % but efficiencies of over 15 % might be achievable, given an appropriate mediator. The efficacy of the mediator depends upon two main factors: it must reversibly undergo one‐electron oxidation and it must possess an oxidation potential in a range of 0.600–0.850 V (vs. a standard hydrogen electrode (SHE) in acetonitrile at 25 °C). Herein, we have examined the effect that structural modifications have on the value of the oxidation potential of cyclic nitroxides as well as the reversibility of the oxidation process. These included alterations to the N‐containing skeleton (pyrrolidine, piperidine, isoindoline, azaphenalene, etc.), as well as the introduction of different substituents (alkyl‐, methoxy‐, amino‐, carboxy‐, etc.) to the ring. Standard oxidation potentials were calculated using high‐level ab initio methodology that was demonstrated to be very accurate (with a mean absolute deviation from experimental values of only 16 mV). An optimal value of 1.45 for the electrostatic scaling factor for UAKS radii in acetonitrile solution was obtained. Established trends in the values of oxidation potentials were used to guide molecular design of stable nitroxides with desired ${E{{{\circ}\hfill \atop {\rm ox}\hfill}}}$ , and a number of compounds were suggested for potential use as enhanced redox mediators in DSSCs.